From: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
This reorganizes the device initialization to init page boundaries
before starting the firmware. This matches the flow in the 8192eu
vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
---
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 68 ++++++++++++------------
1 file changed, 34 insertions(+), 34 deletions(-)
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 2f31c2a..a17d88e 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -4315,6 +4315,40 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
dev_dbg(dev, "%s: macpower %i\n", __func__, macpower);
if (!macpower) {
+ if (priv->ep_tx_normal_queue)
+ val8 = TX_PAGE_NUM_NORM_PQ;
+ else
+ val8 = 0;
+
+ rtl8xxxu_write8(priv, REG_RQPN_NPQ, val8);
+
+ val32 = (TX_PAGE_NUM_PUBQ << RQPN_NORM_PQ_SHIFT) | RQPN_LOAD;
+
+ if (priv->ep_tx_high_queue)
+ val32 |= (TX_PAGE_NUM_HI_PQ << RQPN_HI_PQ_SHIFT);
+ if (priv->ep_tx_low_queue)
+ val32 |= (TX_PAGE_NUM_LO_PQ << RQPN_LO_PQ_SHIFT);
+
+ rtl8xxxu_write32(priv, REG_RQPN, val32);
+
+ /*
+ * Set TX buffer boundary
+ */
+ val8 = TX_TOTAL_PAGE_NUM + 1;
+ rtl8xxxu_write8(priv, REG_TXPKTBUF_BCNQ_BDNY, val8);
+ rtl8xxxu_write8(priv, REG_TXPKTBUF_MGQ_BDNY, val8);
+ rtl8xxxu_write8(priv, REG_TXPKTBUF_WMAC_LBK_BF_HD, val8);
+ rtl8xxxu_write8(priv, REG_TRXFF_BNDY, val8);
+ rtl8xxxu_write8(priv, REG_TDECTRL + 1, val8);
+ }
+
+ ret = rtl8xxxu_init_queue_priority(priv);
+ dev_dbg(dev, "%s: init_queue_priority %i\n", __func__, ret);
+ if (ret)
+ goto exit;
+
+ dev_dbg(dev, "%s: macpower %i\n", __func__, macpower);
+ if (!macpower) {
ret = priv->fops->llt_init(priv, TX_TOTAL_PAGE_NUM);
if (ret) {
dev_warn(dev, "%s: LLT table init failed\n", __func__);
@@ -4392,40 +4426,6 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
priv->rf_mode_ag[0] = rtl8xxxu_read_rfreg(priv, RF_A,
RF6052_REG_MODE_AG);
- dev_dbg(dev, "%s: macpower %i\n", __func__, macpower);
- if (!macpower) {
- if (priv->ep_tx_normal_queue)
- val8 = TX_PAGE_NUM_NORM_PQ;
- else
- val8 = 0;
-
- rtl8xxxu_write8(priv, REG_RQPN_NPQ, val8);
-
- val32 = (TX_PAGE_NUM_PUBQ << RQPN_NORM_PQ_SHIFT) | RQPN_LOAD;
-
- if (priv->ep_tx_high_queue)
- val32 |= (TX_PAGE_NUM_HI_PQ << RQPN_HI_PQ_SHIFT);
- if (priv->ep_tx_low_queue)
- val32 |= (TX_PAGE_NUM_LO_PQ << RQPN_LO_PQ_SHIFT);
-
- rtl8xxxu_write32(priv, REG_RQPN, val32);
-
- /*
- * Set TX buffer boundary
- */
- val8 = TX_TOTAL_PAGE_NUM + 1;
- rtl8xxxu_write8(priv, REG_TXPKTBUF_BCNQ_BDNY, val8);
- rtl8xxxu_write8(priv, REG_TXPKTBUF_MGQ_BDNY, val8);
- rtl8xxxu_write8(priv, REG_TXPKTBUF_WMAC_LBK_BF_HD, val8);
- rtl8xxxu_write8(priv, REG_TRXFF_BNDY, val8);
- rtl8xxxu_write8(priv, REG_TDECTRL + 1, val8);
- }
-
- ret = rtl8xxxu_init_queue_priority(priv);
- dev_dbg(dev, "%s: init_queue_priority %i\n", __func__, ret);
- if (ret)
- goto exit;
-
/*
* Set RX page boundary
*/
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
