On 2015년 11월 12일 20:39, Arnd Bergmann wrote:
On Thursday 12 November 2015 19:05:41 glen lee wrote:
Hi arnd,
I appreciate the patches.
I did test this patch series on h/w which is arm based MCU.
From this patch wilc is not working properly. After downloading firmware, the firmware cannot start and it fails.
I double check this patch and the previous one(14/20) which works fine.
I cannot find the problem in this patch at the moment. I will see if I can find something,
and I'd appreciate if you would help with it.
I've looked at it some more, but didn't find anything obvious, here are some
possible things I found:
-struct wilc_hif_func wilc_hif_sdio = {
- sdio_init,
- sdio_deinit,
- sdio_read_reg,
- sdio_write_reg,
- sdio_read,
- sdio_write,
- sdio_sync,
- sdio_clear_int,
- sdio_read_int,
- sdio_clear_int_ext,
- sdio_read_size,
- sdio_write,
- sdio_read,
- sdio_sync_ext,
-
- sdio_set_max_speed,
- sdio_set_default_speed,
+const struct wilc_hif_func wilc_hif_sdio = {
+ .hif_init = sdio_init,
+ .hif_deinit = sdio_deinit,
+ .hif_read_reg = sdio_read_reg,
+ .hif_write_reg = sdio_write_reg,
+ .hif_block_rx = sdio_read,
+ .hif_block_tx = sdio_write,
+ .hif_sync = sdio_sync,
+ .hif_clear_int = sdio_clear_int,
+ .hif_read_int = sdio_read_int,
+ .hif_clear_int_ext = sdio_clear_int_ext,
+ .hif_read_size = sdio_read_size,
+ .hif_block_rx_ext = sdio_write,
+ .hif_block_tx_ext = sdio_read,
Hi arnd,
I found this. These should be like this. It works fine.
+ .hif_block_tx_ext = sdio_write,
+ .hif_block_rx_ext = sdio_read,
also, wilc_hif_spi need to be fixed together like this.
+ .hif_block_tx_ext = _wilc_spi_write,
+ .hif_block_rx_ext = _wilc_spi_read,
Thank you for all the patches.
regards,
glen lee
+ .hif_sync_ext = sdio_sync_ext,
+ .hif_set_max_bus_speed = sdio_set_max_speed,
+ .hif_set_default_bus_speed = sdio_set_default_speed,
};
If the callbacks are not in the same order here, something could
in theory go wrong. I've tried to verify them by inspection and
could not find anything here, but you can try reverting this part.
memset((void *)&g_wlan, 0, sizeof(wilc_wlan_dev_t));
g_wlan.io_type = wilc->io_type;
-
-#ifdef WILC_SDIO
- if (!wilc_hif_sdio.hif_init(wilc, wilc_debug)) {
- ret = -EIO;
- goto _fail_;
- }
- memcpy((void *)&g_wlan.hif_func, &wilc_hif_sdio,
- sizeof(struct wilc_hif_func));
-#else
- if (!wilc_hif_spi.hif_init(wilc, wilc_debug)) {
+ g_wlan.hif_func = *wilc->ops;
+ if (!g_wlan.hif_func.hif_init(wilc, wilc_debug)) {
ret = -EIO;
goto _fail_;
}
- memcpy((void *)&g_wlan.hif_func, &wilc_hif_spi,
- sizeof(struct wilc_hif_func));
-#endif
This is the most likely part I found:
doing an assigment instead of memcpy should not make a difference,
but my new version also called init after copying over the
operations rather than before. This seemed to be the correct
order when I did it, but it is a change in behavior that might
cause problems if some code relies on the hif_func structure
to be empty at the time that hif_init is called.
Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
