From: David Liu <cfliu.tw@xxxxxxxxx>
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@xxxxxxxxx>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@xxxxxxxxx> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@xxxxxxxxx>
Signed-off-by: Michal Kazior <michal.kazior@xxxxxxxxx>
Tested-by: Michal Kazior <michal.kazior@xxxxxxxxx>
---
drivers/net/wireless/ath/ath10k/core.c | 43 +++++++++++++++++++
drivers/net/wireless/ath/ath10k/core.h | 31 +++++++++++---
drivers/net/wireless/ath/ath10k/debug.c | 21 ++++------
drivers/net/wireless/ath/ath10k/htt.c | 23 +++++++++-
drivers/net/wireless/ath/ath10k/htt.h | 8 ++++
drivers/net/wireless/ath/ath10k/htt_rx.c | 7 ++--
drivers/net/wireless/ath/ath10k/htt_tx.c | 12 +++++-
drivers/net/wireless/ath/ath10k/hw.h | 11 ++---
drivers/net/wireless/ath/ath10k/mac.c | 70 ++++++++++++++++++++++++-------
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 2 +-
drivers/net/wireless/ath/ath10k/wmi.c | 8 ++--
11 files changed, 184 insertions(+), 52 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 59496a9..85162f0 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -31,16 +31,19 @@
#include "wmi-ops.h"
unsigned int ath10k_debug_mask;
+static unsigned int ath10k_cryptmode_param;
static bool uart_print;
static bool skip_otp;
module_param_named(debug_mask, ath10k_debug_mask, uint, 0644);
+module_param_named(cryptmode, ath10k_cryptmode_param, uint, 0644);
module_param(uart_print, bool, 0644);
module_param(skip_otp, bool, 0644);
MODULE_PARM_DESC(debug_mask, "Debugging mask");
MODULE_PARM_DESC(uart_print, "Uart target debugging");
MODULE_PARM_DESC(skip_otp, "Skip otp failure for calibration in testmode");
+MODULE_PARM_DESC(cryptmode, "Crypto mode: 0-hardware, 1-software");
static const struct ath10k_hw_params ath10k_hw_params_list[] = {
{
@@ -991,6 +994,46 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
return -EINVAL;
}
+ ar->wmi.rx_decap_mode = ATH10K_HW_TXRX_NATIVE_WIFI;
+ switch (ath10k_cryptmode_param) {
+ case ATH10K_CRYPT_MODE_HW:
+ clear_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags);
+ clear_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags);
+ break;
+ case ATH10K_CRYPT_MODE_SW:
+ if (!test_bit(ATH10K_FW_FEATURE_RAW_MODE_SUPPORT,
+ ar->fw_features)) {
+ ath10k_err(ar, "cryptmode > 0 requires raw mode support from firmware");
+ return -EINVAL;
+ }
+
+ set_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags);
+ set_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags);
+ break;
+ default:
+ ath10k_info(ar, "invalid cryptmode: %d\n",
+ ath10k_cryptmode_param);
+ return -EINVAL;
+ }
+
+ ar->htt.max_num_amsdu = ATH10K_HTT_MAX_NUM_AMSDU_DEFAULT;
+ ar->htt.max_num_ampdu = ATH10K_HTT_MAX_NUM_AMPDU_DEFAULT;
+
+ if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
+ ar->wmi.rx_decap_mode = ATH10K_HW_TXRX_RAW;
+
+ /* Workaround:
+ *
+ * Firmware A-MSDU aggregation breaks with RAW Tx encap mode
+ * and causes enormous performance issues (malformed frames,
+ * etc).
+ *
+ * Disabling A-MSDU makes RAW mode stable with heavy traffic
+ * albeit a bit slower compared to regular operation.
+ */
+ ar->htt.max_num_amsdu = 1;
+ }
+
/* Backwards compatibility for firmwares without
* ATH10K_FW_IE_WMI_OP_VERSION.
*/
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 45f9603..38d386d 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -91,6 +91,7 @@ struct ath10k_skb_cb {
u8 tid;
u16 freq;
bool is_offchan;
+ bool nohwcrypt;
struct ath10k_htt_txbuf *txbuf;
u32 txbuf_paddr;
} __packed htt;
@@ -151,6 +152,7 @@ struct ath10k_wmi {
const struct wmi_ops *ops;
u32 num_mem_chunks;
+ u32 rx_decap_mode;
struct ath10k_mem_chunk mem_chunks[WMI_MAX_MEM_REQS];
};
@@ -349,6 +351,7 @@ struct ath10k_vif {
} u;
bool use_cts_prot;
+ bool nohwcrypt;
int num_legacy_stations;
int txpower;
struct wmi_wmm_params_all_arg wmm_params;
@@ -390,9 +393,6 @@ struct ath10k_debug {
u32 reg_addr;
u32 nf_cal_period;
- u8 htt_max_amsdu;
- u8 htt_max_ampdu;
-
struct ath10k_fw_crash_data *fw_crash_data;
};
@@ -461,16 +461,21 @@ enum ath10k_fw_features {
ATH10K_FW_FEATURE_WOWLAN_SUPPORT = 6,
/* Don't trust error code from otp.bin */
- ATH10K_FW_FEATURE_IGNORE_OTP_RESULT,
+ ATH10K_FW_FEATURE_IGNORE_OTP_RESULT = 7,
/* Some firmware revisions pad 4th hw address to 4 byte boundary making
* it 8 bytes long in Native Wifi Rx decap.
*/
- ATH10K_FW_FEATURE_NO_NWIFI_DECAP_4ADDR_PADDING,
+ ATH10K_FW_FEATURE_NO_NWIFI_DECAP_4ADDR_PADDING = 8,
/* Firmware supports bypassing PLL setting on init. */
ATH10K_FW_FEATURE_SUPPORTS_SKIP_CLOCK_INIT = 9,
+ /* Raw mode support. If supported, FW supports receiving and trasmitting
+ * frames in raw mode.
+ */
+ ATH10K_FW_FEATURE_RAW_MODE_SUPPORT = 10,
+
/* keep last */
ATH10K_FW_FEATURE_COUNT,
};
@@ -484,6 +489,15 @@ enum ath10k_dev_flags {
* waiters should immediately cancel instead of waiting for a time out.
*/
ATH10K_FLAG_CRASH_FLUSH,
+
+ /* Use Raw mode instead of native WiFi Tx/Rx encap mode.
+ * Raw mode supports both hardware and software crypto. Native WiFi only
+ * supports hardware crypto.
+ */
+ ATH10K_FLAG_RAW_MODE,
+
+ /* Disable HW crypto engine */
+ ATH10K_FLAG_HW_CRYPTO_DISABLED,
};
enum ath10k_cal_mode {
@@ -492,6 +506,13 @@ enum ath10k_cal_mode {
ATH10K_CAL_MODE_DT,
};
+enum ath10k_crypt_mode {
+ /* Only use hardware crypto engine */
+ ATH10K_CRYPT_MODE_HW,
+ /* Only use software crypto engine */
+ ATH10K_CRYPT_MODE_SW,
+};
+
static inline const char *ath10k_cal_mode_str(enum ath10k_cal_mode mode)
{
switch (mode) {
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index 8fa606a..640f3d1 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -124,7 +124,7 @@ EXPORT_SYMBOL(ath10k_info);
void ath10k_print_driver_info(struct ath10k *ar)
{
- ath10k_info(ar, "%s (0x%08x, 0x%08x%s%s%s) fw %s api %d htt %d.%d wmi %d cal %s max_sta %d\n",
+ ath10k_info(ar, "%s (0x%08x, 0x%08x%s%s%s) fw %s api %d htt %d.%d wmi %d cal %s max_sta %d raw %d hwcrypto %d\n",
ar->hw_params.name,
ar->target_version,
ar->chip_id,
@@ -138,7 +138,9 @@ void ath10k_print_driver_info(struct ath10k *ar)
ar->htt.target_version_minor,
ar->wmi.op_version,
ath10k_cal_mode_str(ar->cal_mode),
- ar->max_num_stations);
+ ar->max_num_stations,
+ test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags),
+ !test_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags));
ath10k_info(ar, "debug %d debugfs %d tracing %d dfs %d testmode %d\n",
config_enabled(CONFIG_ATH10K_DEBUG),
config_enabled(CONFIG_ATH10K_DEBUGFS),
@@ -1357,12 +1359,8 @@ static ssize_t ath10k_read_htt_max_amsdu_ampdu(struct file *file,
mutex_lock(&ar->conf_mutex);
- if (ar->debug.htt_max_amsdu)
- amsdu = ar->debug.htt_max_amsdu;
-
- if (ar->debug.htt_max_ampdu)
- ampdu = ar->debug.htt_max_ampdu;
-
+ amsdu = ar->htt.max_num_amsdu;
+ ampdu = ar->htt.max_num_ampdu;
mutex_unlock(&ar->conf_mutex);
len = scnprintf(buf, sizeof(buf), "%u %u\n", amsdu, ampdu);
@@ -1396,8 +1394,8 @@ static ssize_t ath10k_write_htt_max_amsdu_ampdu(struct file *file,
goto out;
res = count;
- ar->debug.htt_max_amsdu = amsdu;
- ar->debug.htt_max_ampdu = ampdu;
+ ar->htt.max_num_amsdu = amsdu;
+ ar->htt.max_num_ampdu = ampdu;
out:
mutex_unlock(&ar->conf_mutex);
@@ -1899,9 +1897,6 @@ void ath10k_debug_stop(struct ath10k *ar)
if (ar->debug.htt_stats_mask != 0)
cancel_delayed_work(&ar->debug.htt_stats_dwork);
- ar->debug.htt_max_amsdu = 0;
- ar->debug.htt_max_ampdu = 0;
-
ath10k_wmi_pdev_pktlog_disable(ar);
}
diff --git a/drivers/net/wireless/ath/ath10k/htt.c b/drivers/net/wireless/ath/ath10k/htt.c
index 6da6ef2..a4e1a1b 100644
--- a/drivers/net/wireless/ath/ath10k/htt.c
+++ b/drivers/net/wireless/ath/ath10k/htt.c
@@ -205,8 +205,27 @@ int ath10k_htt_setup(struct ath10k_htt *htt)
}
status = ath10k_htt_verify_version(htt);
- if (status)
+ if (status) {
+ ath10k_warn(ar, "failed to verify htt version: %d\n",
+ status);
return status;
+ }
+
+ status = ath10k_htt_send_rx_ring_cfg_ll(htt);
+ if (status) {
+ ath10k_warn(ar, "failed to setup rx ring: %d\n",
+ status);
+ return status;
+ }
- return ath10k_htt_send_rx_ring_cfg_ll(htt);
+ status = ath10k_htt_h2t_aggr_cfg_msg(htt,
+ htt->max_num_ampdu,
+ htt->max_num_amsdu);
+ if (status) {
+ ath10k_warn(ar, "failed to setup amsdu/ampdu limit: %d\n",
+ status);
+ return status;
+ }
+
+ return 0;
}
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 7e8a0d8..58ca533 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1325,6 +1325,8 @@ struct ath10k_htt {
u8 target_version_minor;
struct completion target_version_received;
enum ath10k_fw_htt_op_version op_version;
+ u8 max_num_amsdu;
+ u8 max_num_ampdu;
const enum htt_t2h_msg_type *t2h_msg_types;
u32 t2h_msg_types_max;
@@ -1482,6 +1484,12 @@ struct htt_rx_desc {
#define HTT_LOG2_MAX_CACHE_LINE_SIZE 7 /* 2^7 = 128 */
#define HTT_MAX_CACHE_LINE_SIZE_MASK ((1 << HTT_LOG2_MAX_CACHE_LINE_SIZE) - 1)
+/* These values are default in most firmware revisions and apparently are a
+ * sweet spot performance wise.
+ */
+#define ATH10K_HTT_MAX_NUM_AMSDU_DEFAULT 3
+#define ATH10K_HTT_MAX_NUM_AMPDU_DEFAULT 64
+
int ath10k_htt_connect(struct ath10k_htt *htt);
int ath10k_htt_init(struct ath10k *ar);
int ath10k_htt_setup(struct ath10k_htt *htt);
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index 89eb16b..2a6267e 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -1017,9 +1017,8 @@ static void ath10k_htt_rx_h_undecap_raw(struct ath10k *ar,
skb_trim(msdu, msdu->len - FCS_LEN);
/* In most cases this will be true for sniffed frames. It makes sense
- * to deliver them as-is without stripping the crypto param. This would
- * also make sense for software based decryption (which is not
- * implemented in ath10k).
+ * to deliver them as-is without stripping the crypto param. This is
+ * necessary for software based decryption.
*
* If there's no error then the frame is decrypted. At least that is
* the case for frames that come in via fragmented rx indication.
@@ -2074,6 +2073,8 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
break;
case HTT_T2H_MSG_TYPE_CHAN_CHANGE:
break;
+ case HTT_T2H_MSG_TYPE_AGGR_CONF:
+ break;
default:
ath10k_warn(ar, "htt event (%d) not handled\n",
resp->hdr.msg_type);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index a60ef7d..7c81560 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -450,8 +450,12 @@ int ath10k_htt_tx(struct ath10k_htt *htt, struct sk_buff *msdu)
if ((ieee80211_is_action(hdr->frame_control) ||
ieee80211_is_deauth(hdr->frame_control) ||
ieee80211_is_disassoc(hdr->frame_control)) &&
- ieee80211_has_protected(hdr->frame_control))
+ ieee80211_has_protected(hdr->frame_control)) {
skb_put(msdu, IEEE80211_CCMP_MIC_LEN);
+ } else if (!skb_cb->htt.nohwcrypt &&
+ skb_cb->txmode == ATH10K_HW_TXRX_RAW) {
+ skb_put(msdu, IEEE80211_CCMP_MIC_LEN);
+ }
skb_cb->paddr = dma_map_single(dev, msdu->data, msdu->len,
DMA_TO_DEVICE);
@@ -508,12 +512,16 @@ int ath10k_htt_tx(struct ath10k_htt *htt, struct sk_buff *msdu)
prefetch_len);
skb_cb->htt.txbuf->htc_hdr.flags = 0;
+ if (skb_cb->htt.nohwcrypt)
+ flags0 |= HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT;
+
if (!skb_cb->is_protected)
flags0 |= HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT;
flags1 |= SM((u16)vdev_id, HTT_DATA_TX_DESC_FLAGS1_VDEV_ID);
flags1 |= SM((u16)tid, HTT_DATA_TX_DESC_FLAGS1_EXT_TID);
- if (msdu->ip_summed == CHECKSUM_PARTIAL) {
+ if (msdu->ip_summed == CHECKSUM_PARTIAL &&
+ !test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
flags1 |= HTT_DATA_TX_DESC_FLAGS1_CKSUM_L3_OFFLOAD;
flags1 |= HTT_DATA_TX_DESC_FLAGS1_CKSUM_L4_OFFLOAD;
}
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 85cca29..5175e94 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -176,14 +176,16 @@ void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey,
#define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174)
/* Known pecularities:
- * - current FW doesn't support raw rx mode (last tested v599)
- * - current FW dumps upon raw tx mode (last tested v599)
* - raw appears in nwifi decap, raw and nwifi appear in ethernet decap
* - raw have FCS, nwifi doesn't
* - ethernet frames have 802.11 header decapped and parts (base hdr, cipher
* param, llc/snap) are aligned to 4byte boundaries each */
enum ath10k_hw_txrx_mode {
ATH10K_HW_TXRX_RAW = 0,
+
+ /* Native Wifi decap mode is used to align IP frames to 4-byte
+ * boundaries and avoid a very expensive re-alignment in mac80211.
+ */
ATH10K_HW_TXRX_NATIVE_WIFI = 1,
ATH10K_HW_TXRX_ETHERNET = 2,
@@ -245,10 +247,6 @@ enum ath10k_hw_rate_cck {
#define TARGET_RX_TIMEOUT_LO_PRI 100
#define TARGET_RX_TIMEOUT_HI_PRI 40
-/* Native Wifi decap mode is used to align IP frames to 4-byte boundaries and
- * avoid a very expensive re-alignment in mac80211. */
-#define TARGET_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI
-
#define TARGET_SCAN_MAX_PENDING_REQS 4
#define TARGET_BMISS_OFFLOAD_MAX_VDEV 3
#define TARGET_ROAM_OFFLOAD_MAX_VDEV 3
@@ -283,7 +281,6 @@ enum ath10k_hw_rate_cck {
#define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
#define TARGET_10X_RX_TIMEOUT_LO_PRI 100
#define TARGET_10X_RX_TIMEOUT_HI_PRI 40
-#define TARGET_10X_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI
#define TARGET_10X_SCAN_MAX_PENDING_REQS 4
#define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2
#define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index f4de717..6918cee 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -197,6 +197,10 @@ static int ath10k_send_key(struct ath10k_vif *arvif,
return -EOPNOTSUPP;
}
+ if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ }
+
if (cmd == DISABLE_KEY) {
arg.key_cipher = WMI_CIPHER_NONE;
arg.key_data = NULL;
@@ -218,6 +222,9 @@ static int ath10k_install_key(struct ath10k_vif *arvif,
reinit_completion(&ar->install_key_done);
+ if (arvif->nohwcrypt)
+ return 1;
+
ret = ath10k_send_key(arvif, key, cmd, macaddr, flags);
if (ret)
return ret;
@@ -256,7 +263,7 @@ static int ath10k_install_peer_wep_keys(struct ath10k_vif *arvif,
ret = ath10k_install_key(arvif, arvif->wep_keys[i], SET_KEY,
addr, flags);
- if (ret)
+ if (ret < 0)
return ret;
flags = 0;
@@ -264,7 +271,7 @@ static int ath10k_install_peer_wep_keys(struct ath10k_vif *arvif,
ret = ath10k_install_key(arvif, arvif->wep_keys[i], SET_KEY,
addr, flags);
- if (ret)
+ if (ret < 0)
return ret;
spin_lock_bh(&ar->data_lock);
@@ -322,10 +329,10 @@ static int ath10k_clear_peer_keys(struct ath10k_vif *arvif,
/* key flags are not required to delete the key */
ret = ath10k_install_key(arvif, peer->keys[i],
DISABLE_KEY, addr, flags);
- if (ret && first_errno == 0)
+ if (ret < 0 && first_errno == 0)
first_errno = ret;
- if (ret)
+ if (ret < 0)
ath10k_warn(ar, "failed to remove peer wep key %d: %d\n",
i, ret);
@@ -398,7 +405,7 @@ static int ath10k_clear_vdev_key(struct ath10k_vif *arvif,
break;
/* key flags are not required to delete the key */
ret = ath10k_install_key(arvif, key, DISABLE_KEY, addr, flags);
- if (ret && first_errno == 0)
+ if (ret < 0 && first_errno == 0)
first_errno = ret;
if (ret)
@@ -3168,13 +3175,30 @@ ath10k_tx_h_get_txmode(struct ath10k *ar, struct ieee80211_vif *vif,
* Some wmi-tlv firmwares for qca6174 have broken Tx key selection for
* NativeWifi txmode - it selects AP key instead of peer key. It seems
* to work with Ethernet txmode so use it.
+ *
+ * FIXME: Check if raw mode works with TDLS.
*/
if (ieee80211_is_data_present(fc) && sta && sta->tdls)
return ATH10K_HW_TXRX_ETHERNET;
+ if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags))
+ return ATH10K_HW_TXRX_RAW;
+
return ATH10K_HW_TXRX_NATIVE_WIFI;
}
+static bool ath10k_tx_h_use_hwcrypto(struct ieee80211_vif *vif,
+ struct sk_buff *skb) {
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ const u32 mask = IEEE80211_TX_INTFL_DONT_ENCRYPT |
+ IEEE80211_TX_CTL_INJECTED;
+ if ((info->flags & mask) == mask)
+ return false;
+ if (vif)
+ return !ath10k_vif_to_arvif(vif)->nohwcrypt;
+ return true;
+}
+
/* HTT Tx uses Native Wifi tx mode which expects 802.11 frames without QoS
* Control in the header.
*/
@@ -3620,6 +3644,7 @@ static void ath10k_tx(struct ieee80211_hw *hw,
ATH10K_SKB_CB(skb)->htt.is_offchan = false;
ATH10K_SKB_CB(skb)->htt.freq = 0;
ATH10K_SKB_CB(skb)->htt.tid = ath10k_tx_h_get_tid(hdr);
+ ATH10K_SKB_CB(skb)->htt.nohwcrypt = !ath10k_tx_h_use_hwcrypto(vif, skb);
ATH10K_SKB_CB(skb)->vdev_id = ath10k_tx_h_get_vdev_id(ar, vif);
ATH10K_SKB_CB(skb)->txmode = ath10k_tx_h_get_txmode(ar, vif, sta, skb);
ATH10K_SKB_CB(skb)->is_protected = ieee80211_has_protected(fc);
@@ -3635,12 +3660,11 @@ static void ath10k_tx(struct ieee80211_hw *hw,
ath10k_tx_h_8023(skb);
break;
case ATH10K_HW_TXRX_RAW:
- /* FIXME: Packet injection isn't implemented. It should be
- * doable with firmware 10.2 on qca988x.
- */
- WARN_ON_ONCE(1);
- ieee80211_free_txskb(hw, skb);
- return;
+ if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
+ WARN_ON_ONCE(1);
+ ieee80211_free_txskb(hw, skb);
+ return;
+ }
}
if (info->flags & IEEE80211_TX_CTL_TX_OFFCHAN) {
@@ -4236,6 +4260,14 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
goto err;
}
}
+ if (test_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags))
+ arvif->nohwcrypt = true;
+
+ if (arvif->nohwcrypt &&
+ !test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
+ ath10k_warn(ar, "cryptmode module param needed for sw crypto\n");
+ goto err;
+ }
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev create %d (add interface) type %d subtype %d bcnmode %s\n",
arvif->vdev_id, arvif->vdev_type, arvif->vdev_subtype,
@@ -4828,6 +4860,9 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC)
return 1;
+ if (arvif->nohwcrypt)
+ return 1;
+
if (key->keyidx > WMI_MAX_KEY_INDEX)
return -ENOSPC;
@@ -4897,6 +4932,7 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
ret = ath10k_install_key(arvif, key, cmd, peer_addr, flags);
if (ret) {
+ WARN_ON(ret > 0);
ath10k_warn(ar, "failed to install key for vdev %i peer %pM: %d\n",
arvif->vdev_id, peer_addr, ret);
goto exit;
@@ -4912,13 +4948,16 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
ret = ath10k_install_key(arvif, key, cmd, peer_addr, flags2);
if (ret) {
+ WARN_ON(ret > 0);
ath10k_warn(ar, "failed to install (ucast) key for vdev %i peer %pM: %d\n",
arvif->vdev_id, peer_addr, ret);
ret2 = ath10k_install_key(arvif, key, DISABLE_KEY,
peer_addr, flags);
- if (ret2)
+ if (ret2) {
+ WARN_ON(ret2 > 0);
ath10k_warn(ar, "failed to disable (mcast) key for vdev %i peer %pM: %d\n",
arvif->vdev_id, peer_addr, ret2);
+ }
goto exit;
}
}
@@ -6890,7 +6929,6 @@ int ath10k_mac_register(struct ath10k *ar)
IEEE80211_HW_HAS_RATE_CONTROL |
IEEE80211_HW_AP_LINK_PS |
IEEE80211_HW_SPECTRUM_MGMT |
- IEEE80211_HW_SW_CRYPTO_CONTROL |
IEEE80211_HW_CONNECTION_MONITOR |
IEEE80211_HW_SUPPORTS_PER_STA_GTK |
IEEE80211_HW_WANT_MONITOR_VIF |
@@ -6898,6 +6936,9 @@ int ath10k_mac_register(struct ath10k *ar)
IEEE80211_HW_QUEUE_CONTROL |
IEEE80211_HW_SUPPORT_FAST_XMIT;
+ if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags))
+ ar->hw->flags |= IEEE80211_HW_SW_CRYPTO_CONTROL;
+
ar->hw->wiphy->features |= NL80211_FEATURE_STATIC_SMPS;
ar->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;
@@ -6995,7 +7036,8 @@ int ath10k_mac_register(struct ath10k *ar)
goto err_free;
}
- ar->hw->netdev_features = NETIF_F_HW_CSUM;
+ if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags))
+ ar->hw->netdev_features = NETIF_F_HW_CSUM;
if (config_enabled(CONFIG_ATH10K_DFS_CERTIFIED)) {
/* Init ath dfs pattern detector */
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index 563fde7..20ee5a3 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -1334,7 +1334,7 @@ static struct sk_buff *ath10k_wmi_tlv_op_gen_init(struct ath10k *ar)
cfg->rx_timeout_pri[1] = __cpu_to_le32(0x64);
cfg->rx_timeout_pri[2] = __cpu_to_le32(0x64);
cfg->rx_timeout_pri[3] = __cpu_to_le32(0x28);
- cfg->rx_decap_mode = __cpu_to_le32(1);
+ cfg->rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode);
cfg->scan_max_pending_reqs = __cpu_to_le32(4);
cfg->bmiss_offload_max_vdev = __cpu_to_le32(TARGET_TLV_NUM_VDEVS);
cfg->roam_offload_max_vdev = __cpu_to_le32(TARGET_TLV_NUM_VDEVS);
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 77220b0..dc12a53 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -3759,8 +3759,7 @@ static struct sk_buff *ath10k_wmi_op_gen_init(struct ath10k *ar)
config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_be = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_bk = __cpu_to_le32(TARGET_RX_TIMEOUT_HI_PRI);
- config.rx_decap_mode = __cpu_to_le32(TARGET_RX_DECAP_MODE);
-
+ config.rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode);
config.scan_max_pending_reqs =
__cpu_to_le32(TARGET_SCAN_MAX_PENDING_REQS);
@@ -3828,8 +3827,7 @@ static struct sk_buff *ath10k_wmi_10_1_op_gen_init(struct ath10k *ar)
config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_be = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_bk = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_HI_PRI);
- config.rx_decap_mode = __cpu_to_le32(TARGET_10X_RX_DECAP_MODE);
-
+ config.rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode);
config.scan_max_pending_reqs =
__cpu_to_le32(TARGET_10X_SCAN_MAX_PENDING_REQS);
@@ -3894,7 +3892,7 @@ static struct sk_buff *ath10k_wmi_10_2_op_gen_init(struct ath10k *ar)
config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_be = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_bk = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_HI_PRI);
- config.rx_decap_mode = __cpu_to_le32(TARGET_10X_RX_DECAP_MODE);
+ config.rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode);
config.scan_max_pending_reqs =
__cpu_to_le32(TARGET_10X_SCAN_MAX_PENDING_REQS);
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
