Search Linux Wireless

Re: [PATCH] ath10k: implement more versatile set_bitrate_mask

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 17 April 2015 at 09:06, Kalle Valo <kvalo@xxxxxxxxxxxxxxxx> wrote:
> Michal Kazior <michal.kazior@xxxxxxxxx> writes:
>
>> Until now only a single fixed tx rate or nss was
>> allowed to be set.
>>
>> The patch attempts to improve this by allowing
>> most bitrate masks. The limitation is VHT MCS
>> rates cannot be expressed separately using
>> existing firmware interfaces and only the
>> following VHT MCS ranges are supported: none, 0-7,
>> 0-8, and 0-9.
>>
>> This keeps the old behaviour when requesting
>> single tx rate or single nss. The new bitrate mask
>> logic is only applied to other cases that would
>> return -EINVAL until now.
>>
>> Depending on firmware revisions some combinations
>> may crash firmware so use with care, please.
>>
>> This depends on "ath10k: don't use reassoc flag".
>> Without it key cache would effectively be
>> invalidated upon bitrate change leading to
>> communication being no longer possible.
>>
>> Signed-off-by: Michal Kazior <michal.kazior@xxxxxxxxx>
>
> To reduce support questions from the users it would be nice to give few
> good examples how to use this with iw. And also it makes it easier to
> test the patch. If you could send something I can add it to the commit
> log.

Should work:

  iw wlan0 set bitrates legacy 1 6 12 ht-mcs 1 2 3
  iw wlan0 set bitrates legacy-5 mcs-5 7 8 9
  iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9

Won't work:

  iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
  iw wlan0 set bitrates vht-mcs-5 2:7-9

(note the invalid VHT MCS ranges)

Generally the patch removes a lot of limitations from 'set bitrates'
ath10k had. Before it was possible to do only things as described in
51ab1a0a09a8 ("ath10k: add set_bitrate_mask callback").


[...]
>> +             default:
>> +                     /* see ath10k_mac_can_set_bitrate_mask() */
>> +                     WARN_ON(1);
>> +                     /* fall through */
>> +             case -1:
>> +                     mcs = IEEE80211_VHT_MCS_NOT_SUPPORTED; break;
>> +             case 7:
>> +                     mcs = IEEE80211_VHT_MCS_SUPPORT_0_7; break;
>> +             case 8:
>> +                     mcs = IEEE80211_VHT_MCS_SUPPORT_0_8; break;
>> +             case 9:
>> +                     mcs = IEEE80211_VHT_MCS_SUPPORT_0_9; break;
>> +             }
>
> I moved the breaks into their own lines, I think that just easier to
> read. This is the diff:
[snip]

I'm okay with this.


Michał
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux