On Saturday 05 April 2008 01:32:19 Johannes Berg wrote:
> On Sat, 2008-04-05 at 01:09 +0200, Christian Lamparter wrote:
> > Signed-off-by: Christian Lamparter <chunkeey@xxxxxx>
> > ---
> > drivers/net/wireless/Kconfig | 65
> > -------------------------------------- drivers/net/wireless/Makefile
> > | 4 --
> > drivers/net/wireless/p54/Kconfig | 63
> > ++++++++++++++++++++++++++++++++++++ drivers/net/wireless/p54/Makefile |
> > 3 +
>
> You can't do this in five patches, it'll break git bisect. Also, for
> files that are exactly the same you might just want to ask John to do a
> 'git mv' instead of posting full patches.
>
hmm, git bisect skip? or concat all 5 patches into 1, apply and commit?
anyway... you're probably right!
John? can you please do the git mv?
I have attached a diff to make checkpatch.pl happy, so you don't have to do
it. ;-)
Regards,
Chr
--- a/drivers/net/wireless/p54/net2280.h 2008-03-29 16:05:41.000000000 +0100
+++ b/drivers/net/wireless/p54/net2280.h 2008-04-05 00:40:17.000000000 +0200
@@ -37,292 +37,292 @@
/* main registers, BAR0 + 0x0000 */
struct net2280_regs {
- // offset 0x0000
- __le32 devinit;
-#define LOCAL_CLOCK_FREQUENCY 8
-#define FORCE_PCI_RESET 7
-#define PCI_ID 6
-#define PCI_ENABLE 5
-#define FIFO_SOFT_RESET 4
-#define CFG_SOFT_RESET 3
-#define PCI_SOFT_RESET 2
-#define USB_SOFT_RESET 1
-#define M8051_RESET 0
- __le32 eectl;
-#define EEPROM_ADDRESS_WIDTH 23
-#define EEPROM_CHIP_SELECT_ACTIVE 22
-#define EEPROM_PRESENT 21
-#define EEPROM_VALID 20
-#define EEPROM_BUSY 19
-#define EEPROM_CHIP_SELECT_ENABLE 18
-#define EEPROM_BYTE_READ_START 17
-#define EEPROM_BYTE_WRITE_START 16
-#define EEPROM_READ_DATA 8
-#define EEPROM_WRITE_DATA 0
- __le32 eeclkfreq;
- u32 _unused0;
- // offset 0x0010
-
- __le32 pciirqenb0; /* interrupt PCI master ... */
-#define SETUP_PACKET_INTERRUPT_ENABLE 7
-#define ENDPOINT_F_INTERRUPT_ENABLE 6
-#define ENDPOINT_E_INTERRUPT_ENABLE 5
-#define ENDPOINT_D_INTERRUPT_ENABLE 4
-#define ENDPOINT_C_INTERRUPT_ENABLE 3
-#define ENDPOINT_B_INTERRUPT_ENABLE 2
-#define ENDPOINT_A_INTERRUPT_ENABLE 1
-#define ENDPOINT_0_INTERRUPT_ENABLE 0
- __le32 pciirqenb1;
-#define PCI_INTERRUPT_ENABLE 31
-#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
-#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
-#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
-#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
-#define GPIO_INTERRUPT_ENABLE 13
-#define DMA_D_INTERRUPT_ENABLE 12
-#define DMA_C_INTERRUPT_ENABLE 11
-#define DMA_B_INTERRUPT_ENABLE 10
-#define DMA_A_INTERRUPT_ENABLE 9
-#define EEPROM_DONE_INTERRUPT_ENABLE 8
-#define VBUS_INTERRUPT_ENABLE 7
-#define CONTROL_STATUS_INTERRUPT_ENABLE 6
-#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
-#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
-#define RESUME_INTERRUPT_ENABLE 1
-#define SOF_INTERRUPT_ENABLE 0
+ /* offset 0x0000 */
+ __le32 devinit;
+#define LOCAL_CLOCK_FREQUENCY 8
+#define FORCE_PCI_RESET 7
+#define PCI_ID 6
+#define PCI_ENABLE 5
+#define FIFO_SOFT_RESET 4
+#define CFG_SOFT_RESET 3
+#define PCI_SOFT_RESET 2
+#define USB_SOFT_RESET 1
+#define M8051_RESET 0
+ __le32 eectl;
+#define EEPROM_ADDRESS_WIDTH 23
+#define EEPROM_CHIP_SELECT_ACTIVE 22
+#define EEPROM_PRESENT 21
+#define EEPROM_VALID 20
+#define EEPROM_BUSY 19
+#define EEPROM_CHIP_SELECT_ENABLE 18
+#define EEPROM_BYTE_READ_START 17
+#define EEPROM_BYTE_WRITE_START 16
+#define EEPROM_READ_DATA 8
+#define EEPROM_WRITE_DATA 0
+ __le32 eeclkfreq;
+ u32 _unused0;
+ /* offset 0x0010 */
+
+ __le32 pciirqenb0; /* interrupt PCI master ... */
+#define SETUP_PACKET_INTERRUPT_ENABLE 7
+#define ENDPOINT_F_INTERRUPT_ENABLE 6
+#define ENDPOINT_E_INTERRUPT_ENABLE 5
+#define ENDPOINT_D_INTERRUPT_ENABLE 4
+#define ENDPOINT_C_INTERRUPT_ENABLE 3
+#define ENDPOINT_B_INTERRUPT_ENABLE 2
+#define ENDPOINT_A_INTERRUPT_ENABLE 1
+#define ENDPOINT_0_INTERRUPT_ENABLE 0
+ __le32 pciirqenb1;
+#define PCI_INTERRUPT_ENABLE 31
+#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
+#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
+#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
+#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
+#define GPIO_INTERRUPT_ENABLE 13
+#define DMA_D_INTERRUPT_ENABLE 12
+#define DMA_C_INTERRUPT_ENABLE 11
+#define DMA_B_INTERRUPT_ENABLE 10
+#define DMA_A_INTERRUPT_ENABLE 9
+#define EEPROM_DONE_INTERRUPT_ENABLE 8
+#define VBUS_INTERRUPT_ENABLE 7
+#define CONTROL_STATUS_INTERRUPT_ENABLE 6
+#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
+#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
+#define RESUME_INTERRUPT_ENABLE 1
+#define SOF_INTERRUPT_ENABLE 0
__le32 cpu_irqenb0; /* ... or onboard 8051 */
-#define SETUP_PACKET_INTERRUPT_ENABLE 7
-#define ENDPOINT_F_INTERRUPT_ENABLE 6
-#define ENDPOINT_E_INTERRUPT_ENABLE 5
-#define ENDPOINT_D_INTERRUPT_ENABLE 4
-#define ENDPOINT_C_INTERRUPT_ENABLE 3
-#define ENDPOINT_B_INTERRUPT_ENABLE 2
-#define ENDPOINT_A_INTERRUPT_ENABLE 1
-#define ENDPOINT_0_INTERRUPT_ENABLE 0
+#define SETUP_PACKET_INTERRUPT_ENABLE 7
+#define ENDPOINT_F_INTERRUPT_ENABLE 6
+#define ENDPOINT_E_INTERRUPT_ENABLE 5
+#define ENDPOINT_D_INTERRUPT_ENABLE 4
+#define ENDPOINT_C_INTERRUPT_ENABLE 3
+#define ENDPOINT_B_INTERRUPT_ENABLE 2
+#define ENDPOINT_A_INTERRUPT_ENABLE 1
+#define ENDPOINT_0_INTERRUPT_ENABLE 0
__le32 cpu_irqenb1;
-#define CPU_INTERRUPT_ENABLE 31
-#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
-#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
-#define PCI_INTA_INTERRUPT_ENABLE 24
-#define PCI_PME_INTERRUPT_ENABLE 23
-#define PCI_SERR_INTERRUPT_ENABLE 22
-#define PCI_PERR_INTERRUPT_ENABLE 21
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
-#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
-#define GPIO_INTERRUPT_ENABLE 13
-#define DMA_D_INTERRUPT_ENABLE 12
-#define DMA_C_INTERRUPT_ENABLE 11
-#define DMA_B_INTERRUPT_ENABLE 10
-#define DMA_A_INTERRUPT_ENABLE 9
-#define EEPROM_DONE_INTERRUPT_ENABLE 8
-#define VBUS_INTERRUPT_ENABLE 7
-#define CONTROL_STATUS_INTERRUPT_ENABLE 6
-#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
-#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
-#define RESUME_INTERRUPT_ENABLE 1
-#define SOF_INTERRUPT_ENABLE 0
-
- // offset 0x0020
- u32 _unused1;
- __le32 usbirqenb1;
-#define USB_INTERRUPT_ENABLE 31
-#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
-#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
-#define PCI_INTA_INTERRUPT_ENABLE 24
-#define PCI_PME_INTERRUPT_ENABLE 23
-#define PCI_SERR_INTERRUPT_ENABLE 22
-#define PCI_PERR_INTERRUPT_ENABLE 21
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
-#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
-#define GPIO_INTERRUPT_ENABLE 13
-#define DMA_D_INTERRUPT_ENABLE 12
-#define DMA_C_INTERRUPT_ENABLE 11
-#define DMA_B_INTERRUPT_ENABLE 10
-#define DMA_A_INTERRUPT_ENABLE 9
-#define EEPROM_DONE_INTERRUPT_ENABLE 8
-#define VBUS_INTERRUPT_ENABLE 7
-#define CONTROL_STATUS_INTERRUPT_ENABLE 6
-#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
-#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
-#define RESUME_INTERRUPT_ENABLE 1
-#define SOF_INTERRUPT_ENABLE 0
- __le32 irqstat0;
-#define INTA_ASSERTED 12
-#define SETUP_PACKET_INTERRUPT 7
-#define ENDPOINT_F_INTERRUPT 6
-#define ENDPOINT_E_INTERRUPT 5
-#define ENDPOINT_D_INTERRUPT 4
-#define ENDPOINT_C_INTERRUPT 3
-#define ENDPOINT_B_INTERRUPT 2
-#define ENDPOINT_A_INTERRUPT 1
-#define ENDPOINT_0_INTERRUPT 0
- __le32 irqstat1;
-#define POWER_STATE_CHANGE_INTERRUPT 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT 26
-#define PCI_PARITY_ERROR_INTERRUPT 25
-#define PCI_INTA_INTERRUPT 24
-#define PCI_PME_INTERRUPT 23
-#define PCI_SERR_INTERRUPT 22
-#define PCI_PERR_INTERRUPT 21
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
-#define PCI_RETRY_ABORT_INTERRUPT 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
-#define GPIO_INTERRUPT 13
-#define DMA_D_INTERRUPT 12
-#define DMA_C_INTERRUPT 11
-#define DMA_B_INTERRUPT 10
-#define DMA_A_INTERRUPT 9
-#define EEPROM_DONE_INTERRUPT 8
-#define VBUS_INTERRUPT 7
-#define CONTROL_STATUS_INTERRUPT 6
-#define ROOT_PORT_RESET_INTERRUPT 4
-#define SUSPEND_REQUEST_INTERRUPT 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
-#define RESUME_INTERRUPT 1
-#define SOF_INTERRUPT 0
- // offset 0x0030
- __le32 idxaddr;
- __le32 idxdata;
- __le32 fifoctl;
-#define PCI_BASE2_RANGE 16
-#define IGNORE_FIFO_AVAILABILITY 3
-#define PCI_BASE2_SELECT 2
-#define FIFO_CONFIGURATION_SELECT 0
- u32 _unused2;
- // offset 0x0040
- __le32 memaddr;
-#define START 28
-#define DIRECTION 27
-#define FIFO_DIAGNOSTIC_SELECT 24
-#define MEMORY_ADDRESS 0
- __le32 memdata0;
- __le32 memdata1;
- u32 _unused3;
- // offset 0x0050
- __le32 gpioctl;
-#define GPIO3_LED_SELECT 12
-#define GPIO3_INTERRUPT_ENABLE 11
-#define GPIO2_INTERRUPT_ENABLE 10
-#define GPIO1_INTERRUPT_ENABLE 9
-#define GPIO0_INTERRUPT_ENABLE 8
-#define GPIO3_OUTPUT_ENABLE 7
-#define GPIO2_OUTPUT_ENABLE 6
-#define GPIO1_OUTPUT_ENABLE 5
-#define GPIO0_OUTPUT_ENABLE 4
-#define GPIO3_DATA 3
-#define GPIO2_DATA 2
-#define GPIO1_DATA 1
-#define GPIO0_DATA 0
- __le32 gpiostat;
-#define GPIO3_INTERRUPT 3
-#define GPIO2_INTERRUPT 2
-#define GPIO1_INTERRUPT 1
-#define GPIO0_INTERRUPT 0
+#define CPU_INTERRUPT_ENABLE 31
+#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
+#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
+#define PCI_INTA_INTERRUPT_ENABLE 24
+#define PCI_PME_INTERRUPT_ENABLE 23
+#define PCI_SERR_INTERRUPT_ENABLE 22
+#define PCI_PERR_INTERRUPT_ENABLE 21
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
+#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
+#define GPIO_INTERRUPT_ENABLE 13
+#define DMA_D_INTERRUPT_ENABLE 12
+#define DMA_C_INTERRUPT_ENABLE 11
+#define DMA_B_INTERRUPT_ENABLE 10
+#define DMA_A_INTERRUPT_ENABLE 9
+#define EEPROM_DONE_INTERRUPT_ENABLE 8
+#define VBUS_INTERRUPT_ENABLE 7
+#define CONTROL_STATUS_INTERRUPT_ENABLE 6
+#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
+#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
+#define RESUME_INTERRUPT_ENABLE 1
+#define SOF_INTERRUPT_ENABLE 0
+
+ /* offset 0x0020 */
+ u32 _unused1;
+ __le32 usbirqenb1;
+#define USB_INTERRUPT_ENABLE 31
+#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
+#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
+#define PCI_INTA_INTERRUPT_ENABLE 24
+#define PCI_PME_INTERRUPT_ENABLE 23
+#define PCI_SERR_INTERRUPT_ENABLE 22
+#define PCI_PERR_INTERRUPT_ENABLE 21
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
+#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
+#define GPIO_INTERRUPT_ENABLE 13
+#define DMA_D_INTERRUPT_ENABLE 12
+#define DMA_C_INTERRUPT_ENABLE 11
+#define DMA_B_INTERRUPT_ENABLE 10
+#define DMA_A_INTERRUPT_ENABLE 9
+#define EEPROM_DONE_INTERRUPT_ENABLE 8
+#define VBUS_INTERRUPT_ENABLE 7
+#define CONTROL_STATUS_INTERRUPT_ENABLE 6
+#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
+#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
+#define RESUME_INTERRUPT_ENABLE 1
+#define SOF_INTERRUPT_ENABLE 0
+ __le32 irqstat0;
+#define INTA_ASSERTED 12
+#define SETUP_PACKET_INTERRUPT 7
+#define ENDPOINT_F_INTERRUPT 6
+#define ENDPOINT_E_INTERRUPT 5
+#define ENDPOINT_D_INTERRUPT 4
+#define ENDPOINT_C_INTERRUPT 3
+#define ENDPOINT_B_INTERRUPT 2
+#define ENDPOINT_A_INTERRUPT 1
+#define ENDPOINT_0_INTERRUPT 0
+ __le32 irqstat1;
+#define POWER_STATE_CHANGE_INTERRUPT 27
+#define PCI_ARBITER_TIMEOUT_INTERRUPT 26
+#define PCI_PARITY_ERROR_INTERRUPT 25
+#define PCI_INTA_INTERRUPT 24
+#define PCI_PME_INTERRUPT 23
+#define PCI_SERR_INTERRUPT 22
+#define PCI_PERR_INTERRUPT 21
+#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
+#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
+#define PCI_RETRY_ABORT_INTERRUPT 17
+#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
+#define GPIO_INTERRUPT 13
+#define DMA_D_INTERRUPT 12
+#define DMA_C_INTERRUPT 11
+#define DMA_B_INTERRUPT 10
+#define DMA_A_INTERRUPT 9
+#define EEPROM_DONE_INTERRUPT 8
+#define VBUS_INTERRUPT 7
+#define CONTROL_STATUS_INTERRUPT 6
+#define ROOT_PORT_RESET_INTERRUPT 4
+#define SUSPEND_REQUEST_INTERRUPT 3
+#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
+#define RESUME_INTERRUPT 1
+#define SOF_INTERRUPT 0
+ /* offset 0x0030 */
+ __le32 idxaddr;
+ __le32 idxdata;
+ __le32 fifoctl;
+#define PCI_BASE2_RANGE 16
+#define IGNORE_FIFO_AVAILABILITY 3
+#define PCI_BASE2_SELECT 2
+#define FIFO_CONFIGURATION_SELECT 0
+ u32 _unused2;
+ /* offset 0x0040 */
+ __le32 memaddr;
+#define START 28
+#define DIRECTION 27
+#define FIFO_DIAGNOSTIC_SELECT 24
+#define MEMORY_ADDRESS 0
+ __le32 memdata0;
+ __le32 memdata1;
+ u32 _unused3;
+ /* offset 0x0050 */
+ __le32 gpioctl;
+#define GPIO3_LED_SELECT 12
+#define GPIO3_INTERRUPT_ENABLE 11
+#define GPIO2_INTERRUPT_ENABLE 10
+#define GPIO1_INTERRUPT_ENABLE 9
+#define GPIO0_INTERRUPT_ENABLE 8
+#define GPIO3_OUTPUT_ENABLE 7
+#define GPIO2_OUTPUT_ENABLE 6
+#define GPIO1_OUTPUT_ENABLE 5
+#define GPIO0_OUTPUT_ENABLE 4
+#define GPIO3_DATA 3
+#define GPIO2_DATA 2
+#define GPIO1_DATA 1
+#define GPIO0_DATA 0
+ __le32 gpiostat;
+#define GPIO3_INTERRUPT 3
+#define GPIO2_INTERRUPT 2
+#define GPIO1_INTERRUPT 1
+#define GPIO0_INTERRUPT 0
} __attribute__ ((packed));
/* usb control, BAR0 + 0x0080 */
struct net2280_usb_regs {
- // offset 0x0080
- __le32 stdrsp;
-#define STALL_UNSUPPORTED_REQUESTS 31
-#define SET_TEST_MODE 16
-#define GET_OTHER_SPEED_CONFIGURATION 15
-#define GET_DEVICE_QUALIFIER 14
-#define SET_ADDRESS 13
-#define ENDPOINT_SET_CLEAR_HALT 12
-#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
-#define GET_STRING_DESCRIPTOR_2 10
-#define GET_STRING_DESCRIPTOR_1 9
-#define GET_STRING_DESCRIPTOR_0 8
-#define GET_SET_INTERFACE 6
-#define GET_SET_CONFIGURATION 5
-#define GET_CONFIGURATION_DESCRIPTOR 4
-#define GET_DEVICE_DESCRIPTOR 3
-#define GET_ENDPOINT_STATUS 2
-#define GET_INTERFACE_STATUS 1
-#define GET_DEVICE_STATUS 0
- __le32 prodvendid;
-#define PRODUCT_ID 16
-#define VENDOR_ID 0
- __le32 relnum;
- __le32 usbctl;
-#define SERIAL_NUMBER_INDEX 16
-#define PRODUCT_ID_STRING_ENABLE 13
-#define VENDOR_ID_STRING_ENABLE 12
-#define USB_ROOT_PORT_WAKEUP_ENABLE 11
-#define VBUS_PIN 10
-#define TIMED_DISCONNECT 9
-#define SUSPEND_IMMEDIATELY 7
-#define SELF_POWERED_USB_DEVICE 6
-#define REMOTE_WAKEUP_SUPPORT 5
-#define PME_POLARITY 4
-#define USB_DETECT_ENABLE 3
-#define PME_WAKEUP_ENABLE 2
-#define DEVICE_REMOTE_WAKEUP_ENABLE 1
-#define SELF_POWERED_STATUS 0
- // offset 0x0090
- __le32 usbstat;
-#define HIGH_SPEED 7
-#define FULL_SPEED 6
-#define GENERATE_RESUME 5
-#define GENERATE_DEVICE_REMOTE_WAKEUP 4
- __le32 xcvrdiag;
-#define FORCE_HIGH_SPEED_MODE 31
-#define FORCE_FULL_SPEED_MODE 30
-#define USB_TEST_MODE 24
-#define LINE_STATE 16
-#define TRANSCEIVER_OPERATION_MODE 2
-#define TRANSCEIVER_SELECT 1
-#define TERMINATION_SELECT 0
- __le32 setup0123;
- __le32 setup4567;
- // offset 0x0090
- u32 _unused0;
- __le32 ouraddr;
-#define FORCE_IMMEDIATE 7
-#define OUR_USB_ADDRESS 0
- __le32 ourconfig;
+ /* offset 0x0080 */
+ __le32 stdrsp;
+#define STALL_UNSUPPORTED_REQUESTS 31
+#define SET_TEST_MODE 16
+#define GET_OTHER_SPEED_CONFIGURATION 15
+#define GET_DEVICE_QUALIFIER 14
+#define SET_ADDRESS 13
+#define ENDPOINT_SET_CLEAR_HALT 12
+#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
+#define GET_STRING_DESCRIPTOR_2 10
+#define GET_STRING_DESCRIPTOR_1 9
+#define GET_STRING_DESCRIPTOR_0 8
+#define GET_SET_INTERFACE 6
+#define GET_SET_CONFIGURATION 5
+#define GET_CONFIGURATION_DESCRIPTOR 4
+#define GET_DEVICE_DESCRIPTOR 3
+#define GET_ENDPOINT_STATUS 2
+#define GET_INTERFACE_STATUS 1
+#define GET_DEVICE_STATUS 0
+ __le32 prodvendid;
+#define PRODUCT_ID 16
+#define VENDOR_ID 0
+ __le32 relnum;
+ __le32 usbctl;
+#define SERIAL_NUMBER_INDEX 16
+#define PRODUCT_ID_STRING_ENABLE 13
+#define VENDOR_ID_STRING_ENABLE 12
+#define USB_ROOT_PORT_WAKEUP_ENABLE 11
+#define VBUS_PIN 10
+#define TIMED_DISCONNECT 9
+#define SUSPEND_IMMEDIATELY 7
+#define SELF_POWERED_USB_DEVICE 6
+#define REMOTE_WAKEUP_SUPPORT 5
+#define PME_POLARITY 4
+#define USB_DETECT_ENABLE 3
+#define PME_WAKEUP_ENABLE 2
+#define DEVICE_REMOTE_WAKEUP_ENABLE 1
+#define SELF_POWERED_STATUS 0
+ /* offset 0x0090 */
+ __le32 usbstat;
+#define HIGH_SPEED 7
+#define FULL_SPEED 6
+#define GENERATE_RESUME 5
+#define GENERATE_DEVICE_REMOTE_WAKEUP 4
+ __le32 xcvrdiag;
+#define FORCE_HIGH_SPEED_MODE 31
+#define FORCE_FULL_SPEED_MODE 30
+#define USB_TEST_MODE 24
+#define LINE_STATE 16
+#define TRANSCEIVER_OPERATION_MODE 2
+#define TRANSCEIVER_SELECT 1
+#define TERMINATION_SELECT 0
+ __le32 setup0123;
+ __le32 setup4567;
+ /* offset 0x0090 */
+ u32 _unused0;
+ __le32 ouraddr;
+#define FORCE_IMMEDIATE 7
+#define OUR_USB_ADDRESS 0
+ __le32 ourconfig;
} __attribute__ ((packed));
/* pci control, BAR0 + 0x0100 */
struct net2280_pci_regs {
- // offset 0x0100
- __le32 pcimstctl;
-#define PCI_ARBITER_PARK_SELECT 13
-#define PCI_MULTI LEVEL_ARBITER 12
-#define PCI_RETRY_ABORT_ENABLE 11
-#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
-#define DMA_READ_MULTIPLE_ENABLE 9
-#define DMA_READ_LINE_ENABLE 8
-#define PCI_MASTER_COMMAND_SELECT 6
-#define MEM_READ_OR_WRITE 0
-#define IO_READ_OR_WRITE 1
-#define CFG_READ_OR_WRITE 2
-#define PCI_MASTER_START 5
-#define PCI_MASTER_READ_WRITE 4
-#define PCI_MASTER_WRITE 0
-#define PCI_MASTER_READ 1
-#define PCI_MASTER_BYTE_WRITE_ENABLES 0
- __le32 pcimstaddr;
- __le32 pcimstdata;
- __le32 pcimststat;
-#define PCI_ARBITER_CLEAR 2
-#define PCI_EXTERNAL_ARBITER 1
-#define PCI_HOST_MODE 0
+ /* offset 0x0100 */
+ __le32 pcimstctl;
+#define PCI_ARBITER_PARK_SELECT 13
+#define PCI_MULTI LEVEL_ARBITER 12
+#define PCI_RETRY_ABORT_ENABLE 11
+#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
+#define DMA_READ_MULTIPLE_ENABLE 9
+#define DMA_READ_LINE_ENABLE 8
+#define PCI_MASTER_COMMAND_SELECT 6
+#define MEM_READ_OR_WRITE 0
+#define IO_READ_OR_WRITE 1
+#define CFG_READ_OR_WRITE 2
+#define PCI_MASTER_START 5
+#define PCI_MASTER_READ_WRITE 4
+#define PCI_MASTER_WRITE 0
+#define PCI_MASTER_READ 1
+#define PCI_MASTER_BYTE_WRITE_ENABLES 0
+ __le32 pcimstaddr;
+ __le32 pcimstdata;
+ __le32 pcimststat;
+#define PCI_ARBITER_CLEAR 2
+#define PCI_EXTERNAL_ARBITER 1
+#define PCI_HOST_MODE 0
} __attribute__ ((packed));
/* dma control, BAR0 + 0x0180 ... array of four structs like this,
@@ -330,50 +330,50 @@ struct net2280_pci_regs {
* that can be loaded into some of these registers.
*/
struct net2280_dma_regs { /* [11.7] */
- // offset 0x0180, 0x01a0, 0x01c0, 0x01e0,
- __le32 dmactl;
-#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
-#define DMA_CLEAR_COUNT_ENABLE 21
-#define DESCRIPTOR_POLLING_RATE 19
-#define POLL_CONTINUOUS 0
-#define POLL_1_USEC 1
-#define POLL_100_USEC 2
-#define POLL_1_MSEC 3
-#define DMA_VALID_BIT_POLLING_ENABLE 18
-#define DMA_VALID_BIT_ENABLE 17
-#define DMA_SCATTER_GATHER_ENABLE 16
-#define DMA_OUT_AUTO_START_ENABLE 4
-#define DMA_PREEMPT_ENABLE 3
-#define DMA_FIFO_VALIDATE 2
-#define DMA_ENABLE 1
-#define DMA_ADDRESS_HOLD 0
- __le32 dmastat;
-#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
-#define DMA_TRANSACTION_DONE_INTERRUPT 24
-#define DMA_ABORT 1
-#define DMA_START 0
- u32 _unused0[2];
- // offset 0x0190, 0x01b0, 0x01d0, 0x01f0,
+ /* offset 0x0180, 0x01a0, 0x01c0, 0x01e0, */
+ __le32 dmactl;
+#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
+#define DMA_CLEAR_COUNT_ENABLE 21
+#define DESCRIPTOR_POLLING_RATE 19
+#define POLL_CONTINUOUS 0
+#define POLL_1_USEC 1
+#define POLL_100_USEC 2
+#define POLL_1_MSEC 3
+#define DMA_VALID_BIT_POLLING_ENABLE 18
+#define DMA_VALID_BIT_ENABLE 17
+#define DMA_SCATTER_GATHER_ENABLE 16
+#define DMA_OUT_AUTO_START_ENABLE 4
+#define DMA_PREEMPT_ENABLE 3
+#define DMA_FIFO_VALIDATE 2
+#define DMA_ENABLE 1
+#define DMA_ADDRESS_HOLD 0
+ __le32 dmastat;
+#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
+#define DMA_TRANSACTION_DONE_INTERRUPT 24
+#define DMA_ABORT 1
+#define DMA_START 0
+ u32 _unused0[2];
+ /* offset 0x0190, 0x01b0, 0x01d0, 0x01f0, */
__le32 dmacount;
-#define VALID_BIT 31
-#define DMA_DIRECTION 30
-#define DMA_DONE_INTERRUPT_ENABLE 29
-#define END_OF_CHAIN 28
-#define DMA_BYTE_COUNT_MASK ((1<<24)-1)
-#define DMA_BYTE_COUNT 0
- __le32 dmaaddr;
- __le32 dmadesc;
- u32 _unused1;
+#define VALID_BIT 31
+#define DMA_DIRECTION 30
+#define DMA_DONE_INTERRUPT_ENABLE 29
+#define END_OF_CHAIN 28
+#define DMA_BYTE_COUNT_MASK ((1<<24)-1)
+#define DMA_BYTE_COUNT 0
+ __le32 dmaaddr;
+ __le32 dmadesc;
+ u32 _unused1;
} __attribute__ ((packed));
/* dedicated endpoint registers, BAR0 + 0x0200 */
struct net2280_dep_regs { /* [11.8] */
- // offset 0x0200, 0x0210, 0x220, 0x230, 0x240
- __le32 dep_cfg;
- // offset 0x0204, 0x0214, 0x224, 0x234, 0x244
- __le32 dep_rsp;
- u32 _unused[2];
+ /* offset 0x0200, 0x0210, 0x220, 0x230, 0x240 */
+ __le32 dep_cfg;
+ /* offset 0x0204, 0x0214, 0x224, 0x234, 0x244 */
+ __le32 dep_rsp;
+ u32 _unused[2];
} __attribute__ ((packed));
/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
@@ -381,62 +381,62 @@ struct net2280_dep_regs { /* [11.8] */
* ep0 reserved for control; E and F have only 64 bytes of fifo
*/
struct net2280_ep_regs { /* [11.9] */
- // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
- __le32 ep_cfg;
-#define ENDPOINT_BYTE_COUNT 16
-#define ENDPOINT_ENABLE 10
-#define ENDPOINT_TYPE 8
-#define ENDPOINT_DIRECTION 7
-#define ENDPOINT_NUMBER 0
- __le32 ep_rsp;
-#define SET_NAK_OUT_PACKETS 15
-#define SET_EP_HIDE_STATUS_PHASE 14
-#define SET_EP_FORCE_CRC_ERROR 13
-#define SET_INTERRUPT_MODE 12
-#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
-#define SET_NAK_OUT_PACKETS_MODE 10
-#define SET_ENDPOINT_TOGGLE 9
-#define SET_ENDPOINT_HALT 8
-#define CLEAR_NAK_OUT_PACKETS 7
-#define CLEAR_EP_HIDE_STATUS_PHASE 6
-#define CLEAR_EP_FORCE_CRC_ERROR 5
-#define CLEAR_INTERRUPT_MODE 4
-#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
-#define CLEAR_NAK_OUT_PACKETS_MODE 2
-#define CLEAR_ENDPOINT_TOGGLE 1
-#define CLEAR_ENDPOINT_HALT 0
- __le32 ep_irqenb;
-#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
-#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
-#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
-#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
-#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
-#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
- __le32 ep_stat;
-#define FIFO_VALID_COUNT 24
-#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
-#define TIMEOUT 21
-#define USB_STALL_SENT 20
-#define USB_IN_NAK_SENT 19
-#define USB_IN_ACK_RCVD 18
-#define USB_OUT_PING_NAK_SENT 17
-#define USB_OUT_ACK_SENT 16
-#define FIFO_OVERFLOW 13
-#define FIFO_UNDERFLOW 12
-#define FIFO_FULL 11
-#define FIFO_EMPTY 10
-#define FIFO_FLUSH 9
-#define SHORT_PACKET_OUT_DONE_INTERRUPT 6
-#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
-#define NAK_OUT_PACKETS 4
-#define DATA_PACKET_RECEIVED_INTERRUPT 3
-#define DATA_PACKET_TRANSMITTED_INTERRUPT 2
-#define DATA_OUT_PING_TOKEN_INTERRUPT 1
-#define DATA_IN_TOKEN_INTERRUPT 0
- // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
- __le32 ep_avail;
- __le32 ep_data;
- u32 _unused0[2];
+ /* offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 */
+ __le32 ep_cfg;
+#define ENDPOINT_BYTE_COUNT 16
+#define ENDPOINT_ENABLE 10
+#define ENDPOINT_TYPE 8
+#define ENDPOINT_DIRECTION 7
+#define ENDPOINT_NUMBER 0
+ __le32 ep_rsp;
+#define SET_NAK_OUT_PACKETS 15
+#define SET_EP_HIDE_STATUS_PHASE 14
+#define SET_EP_FORCE_CRC_ERROR 13
+#define SET_INTERRUPT_MODE 12
+#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
+#define SET_NAK_OUT_PACKETS_MODE 10
+#define SET_ENDPOINT_TOGGLE 9
+#define SET_ENDPOINT_HALT 8
+#define CLEAR_NAK_OUT_PACKETS 7
+#define CLEAR_EP_HIDE_STATUS_PHASE 6
+#define CLEAR_EP_FORCE_CRC_ERROR 5
+#define CLEAR_INTERRUPT_MODE 4
+#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
+#define CLEAR_NAK_OUT_PACKETS_MODE 2
+#define CLEAR_ENDPOINT_TOGGLE 1
+#define CLEAR_ENDPOINT_HALT 0
+ __le32 ep_irqenb;
+#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
+#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
+#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
+#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
+#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
+#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
+ __le32 ep_stat;
+#define FIFO_VALID_COUNT 24
+#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
+#define TIMEOUT 21
+#define USB_STALL_SENT 20
+#define USB_IN_NAK_SENT 19
+#define USB_IN_ACK_RCVD 18
+#define USB_OUT_PING_NAK_SENT 17
+#define USB_OUT_ACK_SENT 16
+#define FIFO_OVERFLOW 13
+#define FIFO_UNDERFLOW 12
+#define FIFO_FULL 11
+#define FIFO_EMPTY 10
+#define FIFO_FLUSH 9
+#define SHORT_PACKET_OUT_DONE_INTERRUPT 6
+#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
+#define NAK_OUT_PACKETS 4
+#define DATA_PACKET_RECEIVED_INTERRUPT 3
+#define DATA_PACKET_TRANSMITTED_INTERRUPT 2
+#define DATA_OUT_PING_TOKEN_INTERRUPT 1
+#define DATA_IN_TOKEN_INTERRUPT 0
+ /* offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 */
+ __le32 ep_avail;
+ __le32 ep_data;
+ u32 _unused0[2];
} __attribute__ ((packed));
struct net2280_reg_write {
