As communicated with the firmware & hardware teams
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/wil6210/main.c | 23 ++++++++++++++++++-----
drivers/net/wireless/ath/wil6210/wil6210.h | 6 ++++++
2 files changed, 24 insertions(+), 5 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index 7900384..0e95557 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -400,7 +400,7 @@ static inline void wil_release_cpu(struct wil6210_priv *wil)
static int wil_target_reset(struct wil6210_priv *wil)
{
int delay = 0;
- u32 hw_state;
+ u32 x;
u32 rev_id;
bool is_sparrow = (wil->board->board == WIL_BOARD_SPARROW);
@@ -415,9 +415,22 @@ static int wil_target_reset(struct wil6210_priv *wil)
S(RGF_USER_CLKS_CTL_SW_RST_MASK_0, BIT_CAR_PERST_RST);
wil_halt_cpu(wil);
- C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_CAR_AHB_SW_SEL); /* 40 MHz */
if (is_sparrow) {
+ S(RGF_CAF_OSC_CONTROL, BIT_CAF_OSC_XTAL_EN);
+ /* XTAL stabilization should take about 3ms */
+ usleep_range(5000, 7000);
+ x = R(RGF_CAF_PLL_LOCK_STATUS);
+ if (!(x & BIT_CAF_OSC_DIG_XTAL_STABLE)) {
+ wil_err(wil, "Xtal stabilization timeout\n"
+ "RGF_CAF_PLL_LOCK_STATUS = 0x%08x\n", x);
+ return -ETIME;
+ }
+ /* switch 10k to XTAL*/
+ C(RGF_USER_SPARROW_M_4, BIT_SPARROW_M_4_SEL_SLEEP_OR_REF);
+ /* 40 MHz */
+ C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_CAR_AHB_SW_SEL);
+
W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x3ff81f);
W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_1, 0xf);
}
@@ -458,13 +471,13 @@ static int wil_target_reset(struct wil6210_priv *wil)
/* wait until device ready. typical time is 200..250 msec */
do {
msleep(RST_DELAY);
- hw_state = R(RGF_USER_HW_MACHINE_STATE);
+ x = R(RGF_USER_HW_MACHINE_STATE);
if (delay++ > RST_COUNT) {
wil_err(wil, "Reset not completed, hw_state 0x%08x\n",
- hw_state);
+ x);
return -ETIME;
}
- } while (hw_state != HW_MACHINE_BOOT_DONE);
+ } while (x != HW_MACHINE_BOOT_DONE);
/* TODO: Erez check rev_id != 1 */
if (!is_sparrow && (rev_id != 1))
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 7ffaf2f..18f8729 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -117,6 +117,8 @@ struct RGF_ICR {
#define BIT_USER_USER_ICR_SW_INT_2 BIT(18)
#define RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0 (0x880c18)
#define RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_1 (0x880c2c)
+#define RGF_USER_SPARROW_M_4 (0x880c50) /* Sparrow */
+ #define BIT_SPARROW_M_4_SEL_SLEEP_OR_REF BIT(2)
#define RGF_DMA_EP_TX_ICR (0x881bb4) /* struct RGF_ICR */
#define BIT_DMA_EP_TX_ICR_TX_DONE BIT(0)
@@ -152,6 +154,10 @@ struct RGF_ICR {
#define RGF_MAC_MTRL_COUNTER_0 (0x886aa8)
#define RGF_CAF_ICR (0x88946c) /* struct RGF_ICR */
+#define RGF_CAF_OSC_CONTROL (0x88afa4)
+ #define BIT_CAF_OSC_XTAL_EN BIT(0)
+#define RGF_CAF_PLL_LOCK_STATUS (0x88afec)
+ #define BIT_CAF_OSC_DIG_XTAL_STABLE BIT(0)
/* popular locations */
#define HOST_MBOX HOSTADDR(RGF_USER_USER_SCRATCH_PAD)
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
