On Tue, 2014-10-14 at 02:59 +0200, poma wrote: > Realtek RTL8188SU/RTL8191SU/RTL8192SU driver > https://github.com/chunkeey/rtl8192su > & > RTL8188SU > It looks like everything worked correctly here for AP mode, at least from the NM logs. Is that correct? Dan > - lsusb > > Bus 002 Device 003: ID 0bda:8171 Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter > > ~~~~~~~~~~ > > - lsusb -t > > /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M > ... > |__ Port 3: Dev 3, If 0, Class=Vendor Specific Class, Driver=rtl8192su, 480M > > ~~~~~~~~~~~~~~~~~~~~~~~ > > - ethtool -i wlp0s4f1u3 > > driver: rtl8192su > ... > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > - /usr/lib/firmware/rtlwifi/rtl8192sufw.bin > eq > https://github.com/chunkeey/rtl8192su/raw/master/firmwares/rtl8192sufw-ap.bin > > ~~~~~~~~~~~~~~~~~~~~~ > > - iwconfig wlp0s4f1u3 > > wlp0s4f1u3 IEEE 802.11bgn Mode:Master Tx-Power=20 dBm > Retry short limit:7 RTS thr=2347 B Fragment thr:off > Power Management:off > > ~~~~~~~~~~~~~~~~~~~~~ > > - ifconfig wlp0s4f1u3 > > wlp0s4f1u3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > inet 10.42.0.1 netmask 255.255.255.0 broadcast 10.42.0.255 > inet6 fe80::201:2ff:fe03:405 prefixlen 64 scopeid 0x20<link> > ether 00:01:02:03:04:05 txqueuelen 1000 (Ethernet) > RX packets 77 bytes 7421 (7.2 KiB) > RX errors 0 dropped 0 overruns 0 frame 0 > TX packets 126 bytes 27469 (26.8 KiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > > ~~~~~~~~~~~~~~~~~~~~ > > - iw wlp0s4f1u3 info > > Interface wlp0s4f1u3 > ifindex 5 > wdev 0x100000001 > addr 00:01:02:03:04:05 > ssid RTL8188SU(rtl8192su) > type AP > wiphy 1 > channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz > > ~~~~~~~~~ > > - iw list > > Wiphy phy1 > max # scan SSIDs: 4 > max scan IEs length: 2257 bytes > RTS threshold: 2347 > Coverage class: 0 (up to 0m) > Device supports RSN-IBSS. > Supported Ciphers: > * WEP40 (00-0f-ac:1) > * WEP104 (00-0f-ac:5) > * TKIP (00-0f-ac:2) > * CCMP (00-0f-ac:4) > * CMAC (00-0f-ac:6) > Available Antennas: TX 0 RX 0 > Supported interface modes: > * IBSS > * managed > * AP > * AP/VLAN > * monitor > * mesh point > * P2P-client > * P2P-GO > Band 1: > Capabilities: 0x1862 > HT20/HT40 > Static SM Power Save > RX HT20 SGI > RX HT40 SGI > No RX STBC > Max AMSDU length: 7935 bytes > DSSS/CCK HT40 > Maximum RX AMPDU length 65535 bytes (exponent: 0x003) > Minimum RX AMPDU time spacing: 16 usec (0x07) > HT TX/RX MCS rate indexes supported: 0-7, 32 > Bitrates (non-HT): > * 1.0 Mbps > * 2.0 Mbps > * 5.5 Mbps > * 11.0 Mbps > * 6.0 Mbps > * 9.0 Mbps > * 12.0 Mbps > * 18.0 Mbps > * 24.0 Mbps > * 36.0 Mbps > * 48.0 Mbps > * 54.0 Mbps > Frequencies: > * 2412 MHz [1] (20.0 dBm) > * 2417 MHz [2] (20.0 dBm) > * 2422 MHz [3] (20.0 dBm) > * 2427 MHz [4] (20.0 dBm) > * 2432 MHz [5] (20.0 dBm) > * 2437 MHz [6] (20.0 dBm) > * 2442 MHz [7] (20.0 dBm) > * 2447 MHz [8] (20.0 dBm) > * 2452 MHz [9] (20.0 dBm) > * 2457 MHz [10] (20.0 dBm) > * 2462 MHz [11] (20.0 dBm) > * 2467 MHz [12] (20.0 dBm) > * 2472 MHz [13] (20.0 dBm) > * 2484 MHz [14] (disabled) > Supported commands: > * new_interface > * set_interface > * new_key > * start_ap > * new_station > * new_mpath > * set_mesh_config > * set_bss > * authenticate > * associate > * deauthenticate > * disassociate > * join_ibss > * join_mesh > * set_tx_bitrate_mask > * frame > * frame_wait_cancel > * set_wiphy_netns > * set_channel > * set_wds_peer > * probe_client > * set_noack_map > * register_beacons > * start_p2p_device > * set_mcast_rate > * Unknown command (104) > * connect > * disconnect > Supported TX frame types: > * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > Supported RX frame types: > * IBSS: 0x40 0xb0 0xc0 0xd0 > * managed: 0x40 0xd0 > * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * mesh point: 0xb0 0xc0 0xd0 > * P2P-client: 0x40 0xd0 > * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * P2P-device: 0x40 0xd0 > software interface modes (can always be added): > * AP/VLAN > * monitor > interface combinations are not supported > HT Capability overrides: > * MCS: ff ff ff ff ff ff ff ff ff ff > * maximum A-MSDU length > * supported channel width > * short GI for 40 MHz > * max A-MPDU length exponent > * min MPDU start spacing > Device supports TX status socket option. > Device supports HT-IBSS. > Device supports low priority scan. > Device supports scan flush. > Device supports AP scan. > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > - iw wlp0s4f1u3 station dump > > Station 00:22:44:66:88:aa (on wlp0s4f1u3) > inactive time: 15052 ms > rx bytes: 36692 > rx packets: 349 > tx bytes: 67232 > tx packets: 282 > tx retries: 0 > tx failed: 0 > signal: -30 dBm > signal avg: -30 dBm > tx bitrate: 72.2 MBit/s MCS 7 short GI > rx bitrate: 6.0 MBit/s > authorized: yes > authenticated: yes > preamble: long > WMM/WME: yes > MFP: no > TDLS peer: no > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > - /etc/NetworkManager/system-connections/AP > > [connection] > id=AP > uuid=12345678-1234-5678-9abc-123456789abc > type=wifi > autoconnect=true > > [wifi] > ssid=RTL8188SU(rtl8192su) > mode=ap > mac-address=00:01:02:03:04:05 > security=802-11-wireless-security > > [wifi-security] > key-mgmt=wpa-psk > proto=rsn > pairwise=ccmp > psk=passphrase > > [ipv4] > method=shared > > [ipv6] > method=ignore > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > - journalctl NetworkManager > > [ 25.277724] systemd[1]: Starting Network Manager... > [ 25.616088] NM[820]: <info> NetworkManager (version 0.9.10.0-5.git20140704.fc21) is starting... > [ 25.616296] NM[820]: <info> Read config: /etc/NetworkManager/NetworkManager.conf and conf.d: keyfile-plugin.conf > [ 25.616468] NM[820]: <info> WEXT support is enabled > [ 26.111881] NM[820]: <info> Loaded plugin keyfile: (c) 2007 - 2013 Red Hat, Inc. To report bugs please use the NetworkManager mailing list. > [ 26.137541] NM[820]: <info> new connection /etc/NetworkManager/system-connections/enp3s0 > [ 26.271517] NM[820]: <info> new connection /etc/NetworkManager/system-connections/AP > [ 26.281099] NM[820]: <info> new connection /etc/NetworkManager/system-connections/MBB > [ 26.296694] NM[820]: <info> monitoring kernel firmware directory '/lib/firmware'. > [ 26.298418] NM[820]: <info> rfkill0: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:04.1/usb2/2-3/2-3:1.0/ieee80211/phy0/rfkill0) (driver rtl8192su) > [ 26.298898] NM[820]: <info> WiFi hardware radio set enabled > [ 26.299359] NM[820]: <info> WWAN hardware radio set enabled > [ 26.301854] NM[820]: <info> Loaded device plugin: /usr/lib64/NetworkManager/libnm-device-plugin-wwan.so > [ 26.302361] NM[820]: <info> Loaded device plugin: /usr/lib64/NetworkManager/libnm-device-plugin-wifi.so > [ 26.302818] NM[820]: <info> WiFi enabled by radio killswitch; enabled by state file > [ 26.303284] NM[820]: <info> WWAN enabled by radio killswitch; enabled by state file > [ 26.303754] NM[820]: <info> WiMAX enabled by radio killswitch; enabled by state file > [ 26.304255] NM[820]: <info> Networking is enabled by state file > [ 26.304632] systemd[1]: Started Network Manager. > [ 26.313508] NM[820]: <info> (lo): link connected > [ 26.313671] NM[820]: <info> (lo): carrier is ON > [ 26.313817] NM[820]: <info> (lo): new Generic device (driver: 'unknown' ifindex: 1) > [ 26.313967] NM[820]: <info> (lo): exported as /org/freedesktop/NetworkManager/Devices/0 > [ 26.347836] NM[820]: <info> (enp3s0): carrier is OFF > [ 26.365975] NM[820]: <info> (enp3s0): new Ethernet device (driver: 'r8169' ifindex: 3) > [ 26.366704] NM[820]: <info> (enp3s0): exported as /org/freedesktop/NetworkManager/Devices/1 > [ 26.367298] NM[820]: <info> (enp3s0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] > [ 26.389929] NM[820]: <info> (enp3s0): preparing device > [ 26.391212] NM[820]: <info> (wlp0s4f1u3): using nl80211 for WiFi device control > [ 26.391720] NM[820]: <info> (wlp0s4f1u3): driver supports Access Point (AP) mode > [ 26.392201] NM[820]: <info> (wlp0s4f1u3): new 802.11 WiFi device (driver: 'rtl8192su' ifindex: 4) > [ 26.392649] NM[820]: <info> (wlp0s4f1u3): exported as /org/freedesktop/NetworkManager/Devices/2 > [ 26.393123] NM[820]: <info> (wlp0s4f1u3): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] > [ 27.348116] NM[820]: <info> (wlp0s4f1u3): preparing device > [ 27.357681] NM[820]: <info> ModemManager available in the bus > [ 28.033860] NM[820]: <info> (enp3s0): link connected > [ 28.035054] NM[820]: <info> (enp3s0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] > [ 28.035713] NM[820]: <info> Auto-activating connection 'enp3s0'. > [ 28.040332] NM[820]: <info> Activation (enp3s0) starting connection 'enp3s0' > [ 28.040846] NM[820]: <info> Activation (enp3s0) Stage 1 of 5 (Device Prepare) scheduled... > [ 28.041318] NM[820]: <info> Activation (enp3s0) Stage 1 of 5 (Device Prepare) started... > [ 28.041776] NM[820]: <info> (enp3s0): device state change: disconnected -> prepare (reason 'none') [30 40 0] > [ 28.042246] NM[820]: <info> NetworkManager state is now CONNECTING > [ 28.042698] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) scheduled... > [ 28.043182] NM[820]: <info> Activation (enp3s0) Stage 1 of 5 (Device Prepare) complete. > [ 28.043634] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) starting... > [ 28.044072] NM[820]: <info> (enp3s0): device state change: prepare -> config (reason 'none') [40 50 0] > [ 28.061851] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) successful. > [ 28.062348] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) complete. > [ 28.325821] NM[820]: <info> wpa_supplicant started > [ 28.466946] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs > [ 28.467471] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: starting -> ready > [ 28.467930] NM[820]: <info> (wlp0s4f1u3): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] > [ 28.468893] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: ready -> disconnected > [ 28.469370] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs > [ 28.469837] NM[820]: <info> Auto-activating connection 'AP'. > [ 28.475692] NM[820]: <info> Activation (wlp0s4f1u3) starting connection 'AP' > [ 28.476128] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) scheduled... > [ 28.476311] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) started... > [ 28.476491] NM[820]: <info> (wlp0s4f1u3): device state change: disconnected -> prepare (reason 'none') [30 40 0] > [ 28.476672] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) scheduled... > [ 28.476852] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) complete. > [ 28.477047] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) starting... > [ 28.477225] NM[820]: <info> (wlp0s4f1u3): device state change: prepare -> config (reason 'none') [40 50 0] > [ 28.477400] NM[820]: <info> Activation (wlp0s4f1u3/wireless): connection 'AP' has security, and secrets exist. No new secrets needed. > [ 28.477574] NM[820]: <info> Config: added 'ssid' value 'RTL8188SU(rtl8192su)' > [ 28.477750] NM[820]: <info> Config: added 'mode' value '2' > [ 28.477925] NM[820]: <info> Config: added 'frequency' value '2412' > [ 28.478111] NM[820]: <info> Config: added 'key_mgmt' value 'WPA-PSK' > [ 28.478286] NM[820]: <info> Config: added 'psk' value '<omitted>' > [ 28.478459] NM[820]: <info> Config: added 'proto' value 'RSN' > [ 28.478632] NM[820]: <info> Config: added 'pairwise' value 'CCMP' > [ 28.478809] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) complete. > [ 28.478982] NM[820]: <info> Config: set interface ap_scan to 2 > [ 28.738684] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: disconnected -> completed > [ 28.738891] NM[820]: <info> Activation (wlp0s4f1u3/wireless) Stage 2 of 5 (Device Configure) successful. Started Wi-Fi Hotspot 'RTL8188SU(rtl8192su)'. > [ 34.977083] NM[820]: <info> Activation (enp3s0) Stage 3 of 5 (IP Configure Start) scheduled. > [ 34.977610] NM[820]: <info> Activation (enp3s0) Stage 3 of 5 (IP Configure Start) started... > [ 34.978096] NM[820]: <info> (enp3s0): device state change: config -> ip-config (reason 'none') [50 70 0] > [ 34.978554] NM[820]: <info> Activation (enp3s0) Beginning DHCPv4 transaction (timeout in 45 seconds) > [ 35.304547] NM[820]: <info> dhclient started with pid 1395 > [ 35.305087] NM[820]: <info> Activation (enp3s0) Stage 3 of 5 (IP Configure Start) complete. > [ 35.306502] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) scheduled. > [ 35.306985] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) started... > [ 35.307480] NM[820]: <info> (wlp0s4f1u3): device state change: config -> ip-config (reason 'none') [50 70 0] > [ 35.307976] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Configure Commit) scheduled... > [ 35.308447] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) complete. > [ 35.308937] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) started... > [ 35.490657] dhclient[1395]: Internet Systems Consortium DHCP Client 4.3.1 > [ 35.491211] dhclient[1395]: Copyright 2004-2014 Internet Systems Consortium. > [ 35.491674] dhclient[1395]: All rights reserved. > [ 35.492147] dhclient[1395]: For info, please visit https://www.isc.org/software/dhcp/ > [ 35.492592] dhclient[1395]: > [ 35.493078] NM[820]: Internet Systems Consortium DHCP Client 4.3.1 > [ 35.493519] NM[820]: Copyright 2004-2014 Internet Systems Consortium. > [ 35.493950] NM[820]: All rights reserved. > [ 35.494211] NM[820]: For info, please visit https://www.isc.org/software/dhcp/ > [ 36.725988] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 53 --jump ACCEPT > [ 36.733764] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 53 --jump ACCEPT > [ 36.752064] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 67 --jump ACCEPT > [ 36.757195] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 67 --jump ACCEPT > [ 36.776083] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --jump REJECT > [ 36.781590] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --out-interface wlp0s4f1u3 --jump REJECT > [ 36.786875] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --out-interface wlp0s4f1u3 --jump ACCEPT > [ 36.789805] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --source 10.42.0.0/255.255.255.0 --in-interface wlp0s4f1u3 --jump ACCEPT > [ 36.792748] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --destination 10.42.0.0/255.255.255.0 --out-interface wlp0s4f1u3 --match state --state ESTABLISHED,RELATED --jump ACCEPT > [ 38.812843] NM[820]: <info> Executing: /usr/sbin/iptables --table nat --insert POSTROUTING --source 10.42.0.0/255.255.255.0 ! --destination 10.42.0.0/255.255.255.0 --jump MASQUERADE > [ 38.816972] NM[820]: <info> Starting dnsmasq... > [ 38.818556] NM[820]: <info> (wlp0s4f1u3): device state change: ip-config -> ip-check (reason 'none') [70 80 0] > [ 38.818941] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) complete. > [ 38.822707] NM[820]: <info> (enp3s0): DHCPv4 state changed nbi -> preinit > [ 38.825233] NM[820]: <info> (wlp0s4f1u3): device state change: ip-check -> secondaries (reason 'none') [80 90 0] > [ 38.826026] NM[820]: <info> (wlp0s4f1u3): device state change: secondaries -> activated (reason 'none') [90 100 0] > [ 38.881776] dhclient[1395]: Listening on LPF/enp3s0/00:12:34:56:78:30 > [ 38.882317] dhclient[1395]: Sending on LPF/enp3s0/00:12:34:56:78:30 > [ 38.882777] dhclient[1395]: Sending on Socket/fallback > [ 38.883995] dhclient[1395]: DHCPREQUEST on enp3s0 to 255.255.255.255 port 67 (xid=0x9c4e1f) > [ 38.884524] dhclient[1395]: DHCPACK from 192.168.2.1 (xid=0x9c4e1f) > [ 38.885027] NM[820]: Listening on LPF/enp3s0/00:12:34:56:78:30 > [ 38.885471] NM[820]: Sending on LPF/enp3s0/00:12:34:56:78:30 > [ 38.885903] NM[820]: Sending on Socket/fallback > [ 38.886356] NM[820]: DHCPREQUEST on enp3s0 to 255.255.255.255 port 67 (xid=0x9c4e1f) > [ 38.886787] NM[820]: DHCPACK from 192.168.2.1 (xid=0x9c4e1f) > [ 39.008666] dnsmasq[1416]: started, version 2.72 cachesize 150 > [ 39.009255] dnsmasq[1416]: compile time options: IPv6 GNU-getopt DBus no-i18n IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset auth DNSSEC loop-detect > [ 39.009719] dnsmasq-dhcp[1416]: DHCP, IP range 10.42.0.10 -- 10.42.0.254, lease time 1h > [ 39.010186] dnsmasq[1416]: reading /etc/resolv.conf > [ 39.010634] dnsmasq[1416]: using nameserver 192.168.2.1#53 > [ 39.012048] dnsmasq[1416]: cleared cache > [ 44.464210] NM[820]: <info> Activation (wlp0s4f1u3) successful, device activated. > [ 44.470643] NM[820]: <info> (enp3s0): DHCPv4 state changed preinit -> reboot > [ 44.472389] NM[820]: <info> address 192.168.2.35 > [ 44.472910] NM[820]: <info> plen 24 (255.255.255.0) > [ 44.473421] NM[820]: <info> gateway 192.168.2.1 > [ 44.473892] NM[820]: <info> server identifier 192.168.2.1 > [ 44.474382] NM[820]: <info> lease time 600 > [ 44.474841] NM[820]: <info> nameserver '192.168.2.1' > [ 44.476312] NM[820]: <info> Activation (enp3s0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... > [ 44.476428] NM[820]: <info> Activation (enp3s0) Stage 5 of 5 (IPv4 Commit) started... > [ 44.476548] NM[820]: <info> (enp3s0): device state change: ip-config -> ip-check (reason 'none') [70 80 0] > [ 44.476664] NM[820]: <info> Activation (enp3s0) Stage 5 of 5 (IPv4 Commit) complete. > [ 44.476782] NM[820]: <info> (enp3s0): device state change: ip-check -> secondaries (reason 'none') [80 90 0] > [ 44.476897] NM[820]: <info> (enp3s0): device state change: secondaries -> activated (reason 'none') [90 100 0] > [ 44.477060] NM[820]: <info> NetworkManager state is now CONNECTED_LOCAL > [ 44.671564] dhclient[1395]: bound to 192.168.2.35 -- renewal in 253 seconds. > [ 44.672104] NM[820]: bound to 192.168.2.35 -- renewal in 253 seconds. > [ 44.672581] NM[820]: <info> NetworkManager state is now CONNECTED_GLOBAL > [ 44.673074] NM[820]: <info> Policy set 'enp3s0' (enp3s0) as default for IPv4 routing and DNS. > [ 44.719277] NM[820]: <info> Activation (enp3s0) successful, device activated. > [ 44.721265] NM[820]: <info> startup complete > [ 95.712977] dnsmasq[1416]: reading /etc/resolv.conf > [ 95.713657] dnsmasq[1416]: using nameserver 192.168.2.1#53 > [ 95.715255] dnsmasq[1416]: cleared cache > [ 217.044170] dnsmasq-dhcp[1416]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa > [ 217.044896] dnsmasq-dhcp[1416]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef > ... > [ 1240.752553] dnsmasq-dhcp[1416]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa > [ 1240.813416] dnsmasq-dhcp[1416]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef > ... > [ 1408.894826] dnsmasq-dhcp[1416]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa > [ 1408.895557] dnsmasq-dhcp[1416]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef > > - systemctl suspend > & resume(S3) > > [ 1689.325793] NM[820]: <info> (wlp0s4f1u3): device state change: activated -> unmanaged (reason 'removed') [100 10 36] > [ 1689.325961] NM[820]: <info> (wlp0s4f1u3): deactivating device (reason 'removed') [36] > [ 1689.326448] NM[820]: <info> radio killswitch /sys/devices/pci0000:00/0000:00:04.1/usb2/2-3/2-3:1.0/ieee80211/phy0/rfkill0 disappeared > [ 1689.326580] NM[820]: <info> (wlp0s4f1u3): using nl80211 for WiFi device control > [ 1689.326709] NM[820]: <info> (wlp0s4f1u3): driver supports Access Point (AP) mode > [ 1689.326834] NM[820]: <info> (wlp0s4f1u3): new 802.11 WiFi device (driver: 'rtl8192su' ifindex: 5) > [ 1689.326966] NM[820]: <info> (wlp0s4f1u3): exported as /org/freedesktop/NetworkManager/Devices/3 > [ 1689.327098] NM[820]: <info> (wlp0s4f1u3): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] > [ 1689.327223] NM[820]: <info> (wlp0s4f1u3): preparing device > [ 1689.328176] NM[820]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:04.1/usb2/2-3/2-3:1.0/ieee80211/phy1/rfkill1) (driver rtl8192su) > [ 1689.329155] NM[820]: <info> Executing: /usr/sbin/iptables --table nat --delete POSTROUTING --source 10.42.0.0/255.255.255.0 ! --destination 10.42.0.0/255.255.255.0 --jump MASQUERADE > [ 1689.331088] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --destination 10.42.0.0/255.255.255.0 --out-interface wlp0s4f1u3 --match state --state ESTABLISHED,RELATED --jump ACCEPT > [ 1689.334823] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --source 10.42.0.0/255.255.255.0 --in-interface wlp0s4f1u3 --jump ACCEPT > [ 1689.336627] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --in-interface wlp0s4f1u3 --out-interface wlp0s4f1u3 --jump ACCEPT > [ 1689.338561] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --out-interface wlp0s4f1u3 --jump REJECT > [ 1689.341038] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --in-interface wlp0s4f1u3 --jump REJECT > [ 1689.343125] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 67 --jump ACCEPT > [ 1689.380119] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 67 --jump ACCEPT > [ 1689.385774] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 53 --jump ACCEPT > [ 1690.325415] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 53 --jump ACCEPT > [ 1690.336827] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs > [ 1690.337091] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: starting -> ready > [ 1690.337297] NM[820]: <info> (wlp0s4f1u3): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] > [ 1690.337493] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: ready -> disconnected > [ 1690.337686] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs > [ 1690.337884] NM[820]: <info> Auto-activating connection 'AP'. > [ 1690.338085] NM[820]: <info> Activation (wlp0s4f1u3) starting connection 'AP' > [ 1690.338281] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) scheduled... > [ 1690.338472] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) started... > [ 1690.338672] NM[820]: <info> (wlp0s4f1u3): device state change: disconnected -> prepare (reason 'none') [30 40 0] > [ 1690.338865] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) scheduled... > [ 1690.339062] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) complete. > [ 1690.339257] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) starting... > [ 1690.339452] NM[820]: <info> (wlp0s4f1u3): device state change: prepare -> config (reason 'none') [40 50 0] > [ 1690.343841] NM[820]: <info> Activation (wlp0s4f1u3/wireless): access point 'AP' has security, but secrets are required. > [ 1690.344110] NM[820]: <info> (wlp0s4f1u3): device state change: config -> need-auth (reason 'none') [50 60 0] > [ 1690.344304] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) complete. > [ 1690.344436] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) scheduled... > [ 1690.348812] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) started... > [ 1690.348980] NM[820]: <info> (wlp0s4f1u3): device state change: need-auth -> prepare (reason 'none') [60 40 0] > [ 1690.349130] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) scheduled... > [ 1690.349260] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) complete. > [ 1690.349389] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) starting... > [ 1690.349519] NM[820]: <info> (wlp0s4f1u3): device state change: prepare -> config (reason 'none') [40 50 0] > [ 1690.349653] NM[820]: <info> Activation (wlp0s4f1u3/wireless): connection 'AP' has security, and secrets exist. No new secrets needed. > [ 1690.349783] NM[820]: <info> Config: added 'ssid' value 'RTL8188SU(rtl8192su)' > [ 1690.349911] NM[820]: <info> Config: added 'mode' value '2' > [ 1690.350052] NM[820]: <info> Config: added 'frequency' value '2412' > [ 1690.350186] NM[820]: <info> Config: added 'key_mgmt' value 'WPA-PSK' > [ 1690.350311] NM[820]: <info> Config: added 'psk' value '<omitted>' > [ 1690.350440] NM[820]: <info> Config: added 'proto' value 'RSN' > [ 1690.350567] NM[820]: <info> Config: added 'pairwise' value 'CCMP' > [ 1690.350692] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) complete. > [ 1690.355138] NM[820]: <info> Config: set interface ap_scan to 2 > [ 1690.439942] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: disconnected -> completed > [ 1690.440552] NM[820]: <info> Activation (wlp0s4f1u3/wireless) Stage 2 of 5 (Device Configure) successful. Started Wi-Fi Hotspot 'RTL8188SU(rtl8192su)'. > [ 1690.496432] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) scheduled. > [ 1690.497084] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) started... > [ 1690.497617] NM[820]: <info> (wlp0s4f1u3): device state change: config -> ip-config (reason 'none') [50 70 0] > [ 1690.498145] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Configure Commit) scheduled... > [ 1690.498669] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) complete. > [ 1690.499196] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) started... > [ 1690.519773] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 53 --jump ACCEPT > [ 1690.522189] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 53 --jump ACCEPT > [ 1690.550111] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 67 --jump ACCEPT > [ 1690.555813] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 67 --jump ACCEPT > [ 1690.573980] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --jump REJECT > [ 1690.577369] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --out-interface wlp0s4f1u3 --jump REJECT > [ 1690.580764] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --out-interface wlp0s4f1u3 --jump ACCEPT > [ 1690.585441] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --source 10.42.0.0/255.255.255.0 --in-interface wlp0s4f1u3 --jump ACCEPT > [ 1690.587979] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --destination 10.42.0.0/255.255.255.0 --out-interface wlp0s4f1u3 --match state --state ESTABLISHED,RELATED --jump ACCEPT > [ 1690.590492] NM[820]: <info> Executing: /usr/sbin/iptables --table nat --insert POSTROUTING --source 10.42.0.0/255.255.255.0 ! --destination 10.42.0.0/255.255.255.0 --jump MASQUERADE > [ 1690.592764] NM[820]: <info> Starting dnsmasq... > [ 1690.593692] NM[820]: <info> (wlp0s4f1u3): device state change: ip-config -> ip-check (reason 'none') [70 80 0] > [ 1690.594290] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) complete. > [ 1690.595395] dnsmasq[3442]: started, version 2.72 cachesize 150 > [ 1690.595629] dnsmasq[3442]: compile time options: IPv6 GNU-getopt DBus no-i18n IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset auth DNSSEC loop-detect > [ 1690.595822] dnsmasq-dhcp[3442]: DHCP, IP range 10.42.0.10 -- 10.42.0.254, lease time 1h > [ 1690.596021] dnsmasq[3442]: reading /etc/resolv.conf > [ 1690.596216] dnsmasq[3442]: using nameserver 192.168.2.1#53 > [ 1690.596793] dnsmasq[3442]: cleared cache > [ 1690.596982] NM[820]: <info> (wlp0s4f1u3): device state change: ip-check -> secondaries (reason 'none') [80 90 0] > [ 1690.597182] NM[820]: <info> (wlp0s4f1u3): device state change: secondaries -> activated (reason 'none') [90 100 0] > [ 1691.068838] NM[820]: <info> Activation (wlp0s4f1u3) successful, device activated. > [ 1698.780512] dnsmasq-dhcp[3442]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa > [ 1698.781136] dnsmasq-dhcp[3442]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef > > ~~~~~~~ > > - dmesg > > [ 2.126073] usb 2-3: new high-speed USB device number 3 using ehci-pci > [ 2.242873] usb 2-3: New USB device found, idVendor=0bda, idProduct=8171 > [ 2.242880] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > [ 2.242883] usb 2-3: Product: RTL8188S WLAN Adapter > [ 2.242885] usb 2-3: Manufacturer: Manufacturer Realtek > [ 2.242887] usb 2-3: SerialNumber: 00e04c000001 > [ 20.134415] rtlwifi: module verification failed: signature and/or required key missing - tainting kernel > [ 20.517392] rtl8192s_common: Chip version 0x3 > [ 20.686391] rtl_usb: rx_max_size 9100, rx_urb_num 8, in_ep 3 > [ 20.687057] rtl8192su: Power Save off (module option) > [ 20.687639] rtl8192su: FW Power Save off (module option) > [ 20.688394] rtl8192su: Driver for Realtek RTL8192SU/RTL8191SU > Loading firmware rtlwifi/rtl8192sufw.bin > [ 20.689751] usbcore: registered new interface driver rtl8192su > [ 20.850838] ieee80211 phy0: Selected rate control algorithm 'rtl_rc' > [ 20.854551] rtl8192su 2-3:1.0 wlp0s4f1u3: renamed from wlan0 > > - systemctl suspend > > [ 1679.990678] PM: Preparing system for mem sleep > [ 1680.178832] Freezing user space processes ... (elapsed 0.048 seconds) done. > [ 1680.226937] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. > [ 1680.228270] PM: Entering mem sleep > [ 1680.228299] Suspending console(s) (use no_console_suspend to debug) > [ 1682.772451] PM: suspend of devices complete after 2543.533 msecs > [ 1682.773864] PM: late suspend of devices complete after 1.407 msecs > [ 1682.775348] ehci-pci 0000:00:02.1: System wakeup enabled by ACPI > [ 1682.786410] PM: noirq suspend of devices complete after 12.536 msecs > [ 1682.787692] ACPI: Preparing to enter system sleep state S3 > [ 1682.788861] PM: Saving platform NVS memory > > & resume(S3) > > [ 1682.798859] ACPI: Low-level resume complete > [ 1682.798924] PM: Restoring platform NVS memory > [ 1682.844566] ACPI: Waking up from system sleep state S3 > [ 1682.855147] ehci-pci 0000:00:02.1: System wakeup disabled by ACPI > [ 1682.856186] PM: noirq resume of devices complete after 11.457 msecs > [ 1682.856759] PM: early resume of devices complete after 0.531 msecs > [ 1683.074063] PM: resume of devices complete after 217.286 msecs > [ 1683.074332] rtl8192s_common: Chip version 0x3 > [ 1683.218439] rtl_usb: rx_max_size 9100, rx_urb_num 8, in_ep 3 > [ 1683.218484] rtl8192su: Power Save off (module option) > [ 1683.218485] rtl8192su: FW Power Save off (module option) > [ 1683.218694] rtl8192su: Driver for Realtek RTL8192SU/RTL8191SU > Loading firmware rtlwifi/rtl8192sufw.bin > [ 1683.219176] ieee80211 phy1: Selected rate control algorithm 'rtl_rc' > [ 1683.234998] PM: Finishing wakeup. > [ 1683.235003] Restarting tasks ... done. > [ 1683.258259] rtl8192su 2-3:1.0 wlp0s4f1u3: renamed from wlan0 > [ 1683.270928] IPv6: ADDRCONF(NETDEV_UP): wlp0s4f1u3: link is not ready > [ 1684.238973] IPv6: ADDRCONF(NETDEV_UP): wlp0s4f1u3: link is not ready > [ 1684.401143] r8169 0000:03:00.0 enp3s0: link up > [ 1691.249718] IPv6: ADDRCONF(NETDEV_UP): wlp0s4f1u3: link is not ready > [ 1691.376981] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s4f1u3: link becomes ready > > ~~~~~~~~~~~~~~~~~~~~ > > http://goo.gl/3O3Tz4 > > > poma > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-wireless" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
