Search Linux Wireless

[PATCH V4] bcma: use chipcommon node from DT for SoC GPIO chip

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This will allow us to define GPIO-attached devices (LEDs, buttons) in
the the device tree.

Signed-off-by: Rafał Miłecki <zajec5@xxxxxxxxx>
---
This is based on top of
[PATCH v6] bcma: register bcma as device tree driver
that I hope will reach wireless-next git tree.

V2: Describe axi chilren and make gpio a child of chipcommon core.
V3: Make chipcommon a GPIO controller (avoid extra sub-child)
    Speed up finding OF node in driver_gpio.c
V4: Simplify setting of_node in driver_gpio.c
---
 Documentation/devicetree/bindings/bus/bcma.txt | 12 ++++++++++++
 drivers/bcma/driver_gpio.c                     |  4 ++++
 2 files changed, 16 insertions(+)

diff --git a/Documentation/devicetree/bindings/bus/bcma.txt b/Documentation/devicetree/bindings/bus/bcma.txt
index e9070c1..62a4834 100644
--- a/Documentation/devicetree/bindings/bus/bcma.txt
+++ b/Documentation/devicetree/bindings/bus/bcma.txt
@@ -9,6 +9,11 @@ Required properties:
 The cores on the AXI bus are automatically detected by bcma with the
 memory ranges they are using and they get registered afterwards.
 
+The top-level axi bus may contain children representing attached cores
+(devices). This is needed since some hardware details can't be auto
+detected (e.g. IRQ numbers). Also some of the cores may be responsible
+for extra things, e.g. ChipCommon providing access to the GPIO chip.
+
 Example:
 
 	axi@18000000 {
@@ -17,4 +22,11 @@ Example:
 		ranges = <0x00000000 0x18000000 0x00100000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
+
+		chipcommon {
+			reg = <0x00000000 0x1000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
 	};
diff --git a/drivers/bcma/driver_gpio.c b/drivers/bcma/driver_gpio.c
index 8ea497c..57ce5fe 100644
--- a/drivers/bcma/driver_gpio.c
+++ b/drivers/bcma/driver_gpio.c
@@ -218,6 +218,10 @@ int bcma_gpio_init(struct bcma_drv_cc *cc)
 #if IS_BUILTIN(CONFIG_BCM47XX)
 	chip->to_irq		= bcma_gpio_to_irq;
 #endif
+#if IS_BUILTIN(CONFIG_OF)
+	if (cc->core->bus->hosttype == BCMA_HOSTTYPE_SOC)
+		chip->of_node	= cc->core->dev.of_node;
+#endif
 	switch (cc->core->bus->chipinfo.id) {
 	case BCMA_CHIP_ID_BCM5357:
 	case BCMA_CHIP_ID_BCM53572:
-- 
1.8.4.5

--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux