Basic rates setting is done with hardcoded register write with
fixed settings.
This patch introduces a new function that makes it possible to
configure basic rates and it add a check for mac80211
BSS_CHANGED_BASIC_RATES flag in order to eventually invoke that
function when needed.
Signed-off-by: Andrea Merello <andrea.merello@xxxxxxxxx>
---
drivers/net/wireless/rtl818x/rtl8180/dev.c | 51 ++++++++++++++++++++++++++----
1 file changed, 45 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/rtl818x/rtl8180/dev.c b/drivers/net/wireless/rtl818x/rtl8180/dev.c
index 3c2b784..ede8fee 100644
--- a/drivers/net/wireless/rtl818x/rtl8180/dev.c
+++ b/drivers/net/wireless/rtl818x/rtl8180/dev.c
@@ -371,6 +371,36 @@ void rtl8180_set_anaparam(struct rtl8180_priv *priv, u32 anaparam)
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
}
+static void rtl8180_conf_basic_rates(struct ieee80211_hw *dev,
+ u32 rates_mask)
+{
+ struct rtl8180_priv *priv = dev->priv;
+
+ u8 max, min;
+ u16 reg;
+
+ max = fls(rates_mask) - 1;
+ min = ffs(rates_mask) - 1;
+
+ switch (priv->chip_family) {
+
+ case RTL818X_CHIP_FAMILY_RTL8180:
+ /* in 8180 this is NOT a BITMAP */
+ reg = rtl818x_ioread16(priv, &priv->map->BRSR);
+ reg &= ~3;
+ reg |= max;
+ rtl818x_iowrite16(priv, &priv->map->BRSR, reg);
+
+ break;
+
+ case RTL818X_CHIP_FAMILY_RTL8185:
+ /* in 8185 this is a BITMAP */
+ rtl818x_iowrite16(priv, &priv->map->BRSR, rates_mask);
+ rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (max << 4) | min);
+ break;
+ }
+}
+
static int rtl8180_init_hw(struct ieee80211_hw *dev)
{
struct rtl8180_priv *priv = dev->priv;
@@ -441,9 +471,6 @@ static int rtl8180_init_hw(struct ieee80211_hw *dev)
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) {
rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0x81);
- rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
-
- rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
/* TODO: set ClkRun enable? necessary? */
reg = rtl818x_ioread8(priv, &priv->map->GP_ENABLE);
@@ -453,7 +480,6 @@ static int rtl8180_init_hw(struct ieee80211_hw *dev)
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | (1 << 2));
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
} else {
- rtl818x_iowrite16(priv, &priv->map->BRSR, 0x1);
rtl818x_iowrite8(priv, &priv->map->SECURITY, 0);
rtl818x_iowrite8(priv, &priv->map->PHY_DELAY, 0x6);
@@ -461,8 +487,18 @@ static int rtl8180_init_hw(struct ieee80211_hw *dev)
}
priv->rf->init(dev);
- if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185)
- rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
+
+ /* default basic rates are 1,2 Mbps for rtl8180. 1,2,6,9,12,18,24 Mbps
+ * otherwise. bitmask 0x3 and 0x01f3 respectively.
+ * NOTE: currenty rtl8225 RF code changes basic rates, so we need to do
+ * this after rf init.
+ * TODO: try to find out whether RF code really needs to do this..
+ */
+ if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180)
+ rtl8180_conf_basic_rates(dev, 0x3);
+ else
+ rtl8180_conf_basic_rates(dev, 0x1f3);
+
return 0;
}
@@ -857,6 +893,9 @@ static void rtl8180_bss_info_changed(struct ieee80211_hw *dev,
rtl818x_iowrite8(priv, &priv->map->MSR, reg);
}
+ if (changed & BSS_CHANGED_BASIC_RATES)
+ rtl8180_conf_basic_rates(dev, info->basic_rates);
+
if (changed & BSS_CHANGED_ERP_SLOT && priv->rf->conf_erp)
priv->rf->conf_erp(dev, info);
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
