From: Sujith Manoharan <c_manoha@xxxxxxxxxxxxxxxx>
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@xxxxxxxxxxxxxxx
Reported-by: Oleksij Rempel <linux@xxxxxxxxxxxxxxxx>
Signed-off-by: Sujith Manoharan <c_manoha@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath9k/recv.c | 25 ++++++++++++++-----------
1 file changed, 14 insertions(+), 11 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
index 6d643ca..f7cc5b3 100644
--- a/drivers/net/wireless/ath/ath9k/recv.c
+++ b/drivers/net/wireless/ath/ath9k/recv.c
@@ -850,20 +850,15 @@ static int ath9k_process_rate(struct ath_common *common,
enum ieee80211_band band;
unsigned int i = 0;
struct ath_softc __maybe_unused *sc = common->priv;
+ struct ath_hw *ah = sc->sc_ah;
- band = hw->conf.chandef.chan->band;
+ band = ah->curchan->chan->band;
sband = hw->wiphy->bands[band];
- switch (hw->conf.chandef.width) {
- case NL80211_CHAN_WIDTH_5:
+ if (IS_CHAN_QUARTER_RATE(ah->curchan))
rxs->flag |= RX_FLAG_5MHZ;
- break;
- case NL80211_CHAN_WIDTH_10:
+ else if (IS_CHAN_HALF_RATE(ah->curchan))
rxs->flag |= RX_FLAG_10MHZ;
- break;
- default:
- break;
- }
if (rx_stats->rs_rate & 0x80) {
/* HT rate */
@@ -1078,6 +1073,14 @@ static int ath9k_rx_skb_preprocess(struct ath_softc *sc,
rx_stats->is_mybeacon = ath9k_is_mybeacon(sc, hdr);
+ /*
+ * This shouldn't happen, but have a safety check anyway.
+ */
+ if (WARN_ON(!ah->curchan)) {
+ ret = -EINVAL;
+ goto exit;
+ }
+
if (ath9k_process_rate(common, hw, rx_stats, rx_status)) {
ret =-EINVAL;
goto exit;
@@ -1085,8 +1088,8 @@ static int ath9k_rx_skb_preprocess(struct ath_softc *sc,
ath9k_process_rssi(common, hw, rx_stats, rx_status);
- rx_status->band = hw->conf.chandef.chan->band;
- rx_status->freq = hw->conf.chandef.chan->center_freq;
+ rx_status->band = ah->curchan->chan->band;
+ rx_status->freq = ah->curchan->chan->center_freq;
rx_status->antenna = rx_stats->rs_antenna;
rx_status->flag |= RX_FLAG_MACTIME_END;
--
1.8.5.2
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
