From: Sujith Manoharan <c_manoha@xxxxxxxxxxxxxxxx> CL calibration is applicable for all chips and the enable/disable knob comes via the INI file. For PCOEM chips, the calibration data is reused when Fast Channel Change is used. Caldata reuse is not enabled for SoC chips, so remove the CL post processing code. Signed-off-by: Sujith Manoharan <c_manoha@xxxxxxxxxxxxxxxx> --- drivers/net/wireless/ath/ath9k/ar9003_calib.c | 27 ++------------------------- drivers/net/wireless/ath/ath9k/ar9003_phy.c | 9 +++++---- 2 files changed, 7 insertions(+), 29 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c index 347b002..58eacf1 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c +++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c @@ -1236,20 +1236,13 @@ static bool ar9003_hw_init_cal_soc(struct ath_hw *ah, bool txiqcal_done = false; bool is_reusable = true, status = true; bool run_agc_cal = false, sep_iq_cal = false; - u32 rx_delay = 0; /* Use chip chainmask only for calibration */ ar9003_hw_set_chain_masks(ah, ah->caps.rx_chainmask, ah->caps.tx_chainmask); if (ah->enabled_cals & TX_CL_CAL) { - if (caldata && test_bit(TXCLCAL_DONE, &caldata->cal_flags)) - REG_CLR_BIT(ah, AR_PHY_CL_CAL_CTL, - AR_PHY_CL_CAL_ENABLE); - else { - REG_SET_BIT(ah, AR_PHY_CL_CAL_CTL, - AR_PHY_CL_CAL_ENABLE); - run_agc_cal = true; - } + REG_SET_BIT(ah, AR_PHY_CL_CAL_CTL, AR_PHY_CL_CAL_ENABLE); + run_agc_cal = true; } if (IS_CHAN_HALF_RATE(chan) || IS_CHAN_QUARTER_RATE(chan)) @@ -1285,15 +1278,6 @@ skip_tx_iqcal: REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN); } - if (REG_READ(ah, AR_PHY_CL_CAL_CTL) & AR_PHY_CL_CAL_ENABLE) { - rx_delay = REG_READ(ah, AR_PHY_RX_DELAY); - /* Disable BB_active */ - REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_DIS); - udelay(5); - REG_WRITE(ah, AR_PHY_RX_DELAY, AR_PHY_RX_DELAY_DELAY); - REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN); - } - if (run_agc_cal || !(ah->ah_flags & AH_FASTCC)) { /* Calibrate the AGC */ REG_WRITE(ah, AR_PHY_AGC_CONTROL, @@ -1306,11 +1290,6 @@ skip_tx_iqcal: 0, AH_WAIT_TIMEOUT); } - if (REG_READ(ah, AR_PHY_CL_CAL_CTL) & AR_PHY_CL_CAL_ENABLE) { - REG_WRITE(ah, AR_PHY_RX_DELAY, rx_delay); - udelay(5); - } - if (!status) { ath_dbg(common, CALIBRATE, "offset calibration failed to complete in %d ms; noisy environment?\n", @@ -1323,8 +1302,6 @@ skip_tx_iqcal: else if (caldata && test_bit(TXIQCAL_DONE, &caldata->cal_flags)) ar9003_hw_tx_iq_cal_reload(ah); - ar9003_hw_cl_cal_post_proc(ah, is_reusable); - /* Revert chainmask to runtime parameters */ ar9003_hw_set_chain_masks(ah, ah->rxchainmask, ah->txchainmask); diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c index d39b79f..39b71b3 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c @@ -641,11 +641,12 @@ static void ar9003_hw_override_ini(struct ath_hw *ah) else ah->enabled_cals &= ~TX_IQ_CAL; - if (REG_READ(ah, AR_PHY_CL_CAL_CTL) & AR_PHY_CL_CAL_ENABLE) - ah->enabled_cals |= TX_CL_CAL; - else - ah->enabled_cals &= ~TX_CL_CAL; } + + if (REG_READ(ah, AR_PHY_CL_CAL_CTL) & AR_PHY_CL_CAL_ENABLE) + ah->enabled_cals |= TX_CL_CAL; + else + ah->enabled_cals &= ~TX_CL_CAL; } static void ar9003_hw_prog_ini(struct ath_hw *ah, -- 1.8.4.2 -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html