Hi! Thank you, that's helped and after entering these commands device began to work, but: But after some network activity through this device (`apt-get update` - about ~2-3 MB downloaded and that was about ~60 secs after successful modprobe) interface was deleted with following logs in dmesg: [362.612028] usb 1-3: TX queue stuck (tot 2 pend 2) [362.612036] usb 1-3: Will restart dongle [362.612272] usb 1-3: USB disconnect, device number 3 [362.612769] wlan0: deauthenticating from 90:f6:52:c6:3c:eb by local choice (reason=3) ... <some logs from cfg80211 module> [363.108058] usb 1-3: new high-speed USB device number 6 using ehci-pci [363.241150] usb 1-3: New USB device found, idVendor=07d1, idProduct=3a0d [363.241157] usb 1-3: New USB device string: Mfr=1, Product=2, Serial Number = 3 ... <just another device info> [365.240030] usb 1-3: timeout waiting for command reply [365.240038] usb 1-3: could not initialize adapter [365.240263] usb 1-3: RX USB error -2. [365.240271] usb 1-3: error -1 when submitting rx usb [365.240334] ar5523: probe of 1-3:1.0 failed with error -110 Switching off and ejecting adapter doesn't help: the same error repeated: > ar5523: probe of 1-3:1.0 failed with error -110 But I found that rebooting to Windows makes the adapter working. After that I rebooted back to Linux and adapter began to work about ~60 secs, but after that the same situation as described above repeated. Also I noted following: without rebooting to Windows - just after rebooting Linux - adapter does not work: _only_ after rebooting to Windows and only now back to Linux. Windows is doing something with adapter I do not know what, but after that adapter works for about 1 minute and disconnected with logs above. What can I do now to solve that problem? Dmitry. On Tue, Jul 9, 2013 at 4:36 PM, Larry Finger <Larry.Finger@xxxxxxxxxxxx> wrote: > On 07/09/2013 03:59 AM, Dmitry Zganyaiko wrote: >> >> Hi! I'm using usb wireless adaptor named >> 07d1:3a0d D-Link System DWA-120 802.11g Wireless 108G (taken from lsusb) >> >> System is Debian wheezy with 3.8 kernel taken from ubuntu reps. But after >> launch this adaptor doesn't work: no any new network interfaces is shown in >> ifconfig. >> >> As far as I understood, such vendor:product (07d1:3a0d) isn't specified in >> drivers/net/wireless/ath/ar5523/ar5523.c, and therefore the driver doesn't >> recognise my device. Firmware 'ar5523.bin' is located in >> /usr/local/lib/firmware. >> >> What can I do to make this adaptor work? Only add that v:p pair to >> ar5523.c and recompile it? Just if that can be done without compiling - it >> will be great. > > > You can test to see if it works with that kernel with the following commands > (as root): > > modprobe -v ar5523 > echo 07d1 3a0d > /sys/bus/usb/drivers/ar5523/new_id > > If the device would work by adding that USB ID to the device table, then the > above commands should accomplish the same result. Note - these commands will > need to be re-entered after every reload of ar5523. > > Larry > -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
