On Fri, 2013-06-28 at 16:21 +0300, Luciano Coelho wrote:
> On Fri, 2013-06-28 at 15:18 +0300, Felipe Balbi wrote:
> > On Fri, Jun 28, 2013 at 03:13:52PM +0300, Luciano Coelho wrote:
> > > On Fri, 2013-06-28 at 14:41 +0300, Felipe Balbi wrote:
> > > > On Fri, Jun 28, 2013 at 02:22:11PM +0300, Luciano Coelho wrote:
> > > > > On Fri, 2013-06-28 at 13:31 +0300, Luciano Coelho wrote:
> > > > > > (fixed Mike's address)
> > > > > >
> > > > > > On Fri, 2013-06-28 at 11:21 +0100, Mark Rutland wrote:
> > > > > > > On Fri, Jun 28, 2013 at 10:53:35AM +0100, Luciano Coelho wrote:
> > > > > > > > On Fri, 2013-06-28 at 10:38 +0100, Mark Rutland wrote:
> > > > > > > > > On Tue, Jun 25, 2013 at 09:35:30AM +0100, Luciano Coelho wrote:
> > > > > > > > > > +Optional properties:
> > > > > > > > > > +--------------------
> > > > > > > > > > +
> > > > > > > > > > +- refclock: the internal WLAN reference clock frequency (required for
> > > > > > > > > > + WiLink6 and WiLink7; not used for WiLink8). Must be one of the
> > > > > > > > > > + following:
> > > > > > > > > > + 0 = 19.2 MHz
> > > > > > > > > > + 1 = 26.0 MHz
> > > > > > > > > > + 2 = 38.4 MHz
> > > > > > > > > > + 3 = 52.0 MHz
> > > > > > > > > > + 4 = 38.4 MHz, XTAL
> > > > > > > > > > + 5 = 26.0 MHz, XTAL
> > > > > > > > > > +
> > > > > > > > > > +- tcxoclock: the internal WLAN TCXO clock frequency (required for
> > > > > > > > > > + WiLink7 not used for WiLink6 and WiLink8). Must be one of the
> > > > > > > > > > + following:
> > > > > > > > > > + 0 = 19.200 MHz
> > > > > > > > > > + 1 = 26.000 MHz
> > > > > > > > > > + 2 = 38.400 MHz
> > > > > > > > > > + 3 = 52.000 MHz
> > > > > > > > > > + 4 = 16.368 MHz
> > > > > > > > > > + 5 = 32.736 MHz
> > > > > > > > > > + 6 = 16.800 MHz
> > > > > > > > > > + 7 = 33.600 MHz
> > > > > > > > >
> > > > > > > > > This looks suspiciously like what we have the common clock bindings for:
> > > > > > > > >
> > > > > > > > > refclk {
> > > > > > > > > compatible = "fixed-clock";
> > > > > > > > > #clock-cells = <0>;
> > > > > > > > > clock-frequency = <19200000>;
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > wilink {
> > > > > > > > > compatible = "ti,wilink7";
> > > > > > > > > interrupt-parent = <&some_interrupt_controller>;
> > > > > > > > > interrupts = <0 1 1>;
> > > > > > > > > clocks = <&refclk>, <&refclk>;
> > > > > > > > > clock-names = "refclk", "txoclk";
> > > > > > > > > };
> > > > > > > > >
> > > > > > > > > Could you not use them?
> > > > > > > >
> > > > > > > > Hmmm... this actually does look good. But these are internal clocks in
> > > > > > > > the modules, they cannot be accessed from outside. Does it make sense
> > > > > > > > to register them with the clock framework?
> > > > > > >
> > > > > > > Given we already have a common way of describing clocks, I think it
> > > > > > > makes sense to use it -- people already understand the common bindings,
> > > > > > > and it's less code to add add to the kernel. I don't think the fact
> > > > > > > these clocks are internal should prevent us from describing them as we
> > > > > > > would an external clock.
> > > > > >
> > > > > > Yes, I agree with you. Thanks for the suggestion! I think it will look
> > > > > > much better. And now that I dug a bit more into the code, I can see
> > > > > > that there are only structs being populated, so there shouldn't be any
> > > > > > other side-effects.
> > > > >
> > > > > Hmmm, one thing that escaped me. Besides the frequency, I also need a
> > > > > boolean that tells if the clock is XTAL or not. I can't figure out how
> > > > > to pass this if I use the generic clock framework. Any suggestions?
> > > >
> > > > Could you use clock-output-names for that ?
> > > >
> > > > XTAL clock:
> > > >
> > > > refclk {
> > > > compatible = "fixed-clock";
> > > > #clock cells = <0>;
> > > > clock-frequency = <19200000>;
> > > > clock-output-names = "xtal";
> > > > };
> > > >
> > > > non-XTAL clock:
> > > >
> > > > refclk {
> > > > compatible = "fixed-clock";
> > > > #clock cells = <0>;
> > > > clock-frequency = <19200000>;
> > > > clock-output-names = "osc"; /* any better name ? */
> > > > };
> > >
> > > This starts looking a bit hacky. Using the output name as a flag is not
> > > very pretty.
> > >
> > > I think it would be better to have a separate flag for it in the wlan
> > > node. Like an optional "refclock-xtal" boolean or something. The
> > > downside of this is that we would be adding information about the clock
> > > details in the wilink node. :(
> > >
> > > OTOH, we could add a flag to the generic clock binding? A new optional
> > > boolean that tells whether the clock is XTAL or not:
> > >
> > > refclk {
> > > compatible = "fixed-clock";
> > > #clock cells = <0>;
> > > clock-frequency = <19200000>;
> > > clock-xtal;
> > > };
> > >
> > > Do you think that would make sense?
> >
> > sure, that looks alright to me. Surely there are other devices out there
> > who want to know if the clock comes from a crystal or not ?!?
>
> Mike, what do you think about this idea? If it sounds okay to you, I can
> cook up a patch adding this flag.
Hmmm... I started implementing this whole thing, but using these clocks
as "fixed-clock"s is not so straightforward. The problem is that I
would need to register my driver as a clock provider and add the OF
match for "fixed-clock".
If I do that, all the other "fixed-clock" nodes would be passed to my
driver too, which is wrong. Or, the platform should register the
"fixed-clock" match, but this would be wrong too, since it would find
*my* fixed-clocks.
The only thing I can come up with is to make a small clock driver (maybe
even inside the WiLink module itself) that registers a new type of
clock, "ti,wilink-clock" or something. But this would really be
overkill, wouldn't it?
Any other ideas?
--
Luca.
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
