From: Kirshenbaum Erez <erezk@xxxxxxxxxxxx>
WMI PCP Start flow should not be handled through:
net_device_ops->ndo_open()->wil_up()->__wil_up()
because it missing mandatory FW parameters (SSID,Channel,IEs, Security...).
Prior to AP starting __wil_up() may be called with iftype set
cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION)
depend on the application hostapd/wpa_supplicant/iw.
there should not be an attempt to start an AP flow,
AP/PCP start flow will be started latter by cfg80211_ops->start_ap().
Signed-off-by: Kirshenbaum Erez <erezk@xxxxxxxxxxxx>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/wil6210/main.c | 34 ---------------------------------
1 file changed, 34 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index 8cafa45..0a2844c 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -286,10 +286,7 @@ static int __wil_up(struct wil6210_priv *wil)
{
struct net_device *ndev = wil_to_ndev(wil);
struct wireless_dev *wdev = wil->wdev;
- struct ieee80211_channel *channel = wdev->preset_chandef.chan;
int rc;
- int bi;
- u16 wmi_nettype = wil_iftype_nl2wmi(wdev->iftype);
rc = wil_reset(wil);
if (rc)
@@ -300,32 +297,25 @@ static int __wil_up(struct wil6210_priv *wil)
if (rc)
return rc;
- /* FIXME Firmware works now in PBSS mode(ToDS=0, FromDS=0) */
- wmi_nettype = wil_iftype_nl2wmi(NL80211_IFTYPE_ADHOC);
switch (wdev->iftype) {
case NL80211_IFTYPE_STATION:
wil_dbg_misc(wil, "type: STATION\n");
- bi = 0;
ndev->type = ARPHRD_ETHER;
break;
case NL80211_IFTYPE_AP:
wil_dbg_misc(wil, "type: AP\n");
- bi = 100;
ndev->type = ARPHRD_ETHER;
break;
case NL80211_IFTYPE_P2P_CLIENT:
wil_dbg_misc(wil, "type: P2P_CLIENT\n");
- bi = 0;
ndev->type = ARPHRD_ETHER;
break;
case NL80211_IFTYPE_P2P_GO:
wil_dbg_misc(wil, "type: P2P_GO\n");
- bi = 100;
ndev->type = ARPHRD_ETHER;
break;
case NL80211_IFTYPE_MONITOR:
wil_dbg_misc(wil, "type: Monitor\n");
- bi = 0;
ndev->type = ARPHRD_IEEE80211_RADIOTAP;
/* ARPHRD_IEEE80211 or ARPHRD_IEEE80211_RADIOTAP ? */
break;
@@ -333,33 +323,9 @@ static int __wil_up(struct wil6210_priv *wil)
return -EOPNOTSUPP;
}
- /* Apply profile in the following order: */
- /* SSID and channel for the AP */
- switch (wdev->iftype) {
- case NL80211_IFTYPE_AP:
- case NL80211_IFTYPE_P2P_GO:
- if (wdev->ssid_len == 0) {
- wil_err(wil, "SSID not set\n");
- return -EINVAL;
- }
- rc = wmi_set_ssid(wil, wdev->ssid_len, wdev->ssid);
- if (rc)
- return rc;
- break;
- default:
- break;
- }
-
/* MAC address - pre-requisite for other commands */
wmi_set_mac_address(wil, ndev->dev_addr);
- /* Set up beaconing if required. */
- if (bi > 0) {
- rc = wmi_pcp_start(wil, bi, wmi_nettype,
- (channel ? channel->hw_value : 0));
- if (rc)
- return rc;
- }
napi_enable(&wil->napi_rx);
napi_enable(&wil->napi_tx);
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
