Signed-off-by: Kalle Valo <kvalo@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath10k/targaddrs.h | 449 +++++++++++++++++++++++++++
1 file changed, 449 insertions(+)
create mode 100644 drivers/net/wireless/ath/ath10k/targaddrs.h
diff --git a/drivers/net/wireless/ath/ath10k/targaddrs.h b/drivers/net/wireless/ath/ath10k/targaddrs.h
new file mode 100644
index 0000000..be7ba1e
--- /dev/null
+++ b/drivers/net/wireless/ath/ath10k/targaddrs.h
@@ -0,0 +1,449 @@
+/*
+ * Copyright (c) 2005-2011 Atheros Communications Inc.
+ * Copyright (c) 2011-2013 Qualcomm Atheros, Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef __TARGADDRS_H__
+#define __TARGADDRS_H__
+
+/*
+ * xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the
+ * host_interest structure. It must match the address of the _host_interest
+ * symbol (see linker script).
+ *
+ * Host Interest is shared between Host and Target in order to coordinate
+ * between the two, and is intended to remain constant (with additions only
+ * at the end) across software releases.
+ *
+ * All addresses are available here so that it's possible to
+ * write a single binary that works with all Target Types.
+ * May be used in assembler code as well as C.
+ */
+#define QCA988X_HOST_INTEREST_ADDRESS 0x00400800
+#define HOST_INTEREST_MAX_SIZE 0x200
+
+/*
+ * These are items that the Host may need to access via BMI or via the
+ * Diagnostic Window. The position of items in this structure must remain
+ * constant across firmware revisions! Types for each item must be fixed
+ * size across target and host platforms. More items may be added at the end.
+ */
+struct host_interest {
+ /*
+ * Pointer to application-defined area, if any.
+ * Set by Target application during startup.
+ */
+ u32 hi_app_host_interest; /* 0x00 */
+
+ /* Pointer to register dump area, valid after Target crash. */
+ u32 hi_failure_state; /* 0x04 */
+
+ /* Pointer to debug logging header */
+ u32 hi_dbglog_hdr; /* 0x08 */
+
+ u32 hi_unused0c; /* 0x0c */
+
+ /*
+ * General-purpose flag bits, similar to SOC_OPTION_* flags.
+ * Can be used by application rather than by OS.
+ */
+ u32 hi_option_flag; /* 0x10 */
+
+ /*
+ * Boolean that determines whether or not to
+ * display messages on the serial port.
+ */
+ u32 hi_serial_enable; /* 0x14 */
+
+ /* Start address of DataSet index, if any */
+ u32 hi_dset_list_head; /* 0x18 */
+
+ /* Override Target application start address */
+ u32 hi_app_start; /* 0x1c */
+
+ /* Clock and voltage tuning */
+ u32 hi_skip_clock_init; /* 0x20 */
+ u32 hi_core_clock_setting; /* 0x24 */
+ u32 hi_cpu_clock_setting; /* 0x28 */
+ u32 hi_system_sleep_setting; /* 0x2c */
+ u32 hi_xtal_control_setting; /* 0x30 */
+ u32 hi_pll_ctrl_setting_24ghz; /* 0x34 */
+ u32 hi_pll_ctrl_setting_5ghz; /* 0x38 */
+ u32 hi_ref_voltage_trim_setting; /* 0x3c */
+ u32 hi_clock_info; /* 0x40 */
+
+ /* Host uses BE CPU or not */
+ u32 hi_be; /* 0x44 */
+
+ u32 hi_stack; /* normal stack */ /* 0x48 */
+ u32 hi_err_stack; /* error stack */ /* 0x4c */
+ u32 hi_desired_cpu_speed_hz; /* 0x50 */
+
+ /* Pointer to Board Data */
+ u32 hi_board_data; /* 0x54 */
+
+ /*
+ * Indication of Board Data state:
+ * 0: board data is not yet initialized.
+ * 1: board data is initialized; unknown size
+ * >1: number of bytes of initialized board data
+ */
+ u32 hi_board_data_initialized; /* 0x58 */
+
+ u32 hi_dset_ram_index_table; /* 0x5c */
+
+ u32 hi_desired_baud_rate; /* 0x60 */
+ u32 hi_dbglog_config; /* 0x64 */
+ u32 hi_end_ram_reserve_sz; /* 0x68 */
+ u32 hi_mbox_io_block_sz; /* 0x6c */
+
+ u32 hi_num_bpatch_streams; /* 0x70 -- unused */
+ u32 hi_mbox_isr_yield_limit; /* 0x74 */
+
+ u32 hi_refclk_hz; /* 0x78 */
+ u32 hi_ext_clk_detected; /* 0x7c */
+ u32 hi_dbg_uart_txpin; /* 0x80 */
+ u32 hi_dbg_uart_rxpin; /* 0x84 */
+ u32 hi_hci_uart_baud; /* 0x88 */
+ u32 hi_hci_uart_pin_assignments; /* 0x8C */
+
+ u32 hi_hci_uart_baud_scale_val; /* 0x90 */
+ u32 hi_hci_uart_baud_step_val; /* 0x94 */
+
+ u32 hi_allocram_start; /* 0x98 */
+ u32 hi_allocram_sz; /* 0x9c */
+ u32 hi_hci_bridge_flags; /* 0xa0 */
+ u32 hi_hci_uart_support_pins; /* 0xa4 */
+
+ u32 hi_hci_uart_pwr_mgmt_params; /* 0xa8 */
+
+ /*
+ * 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
+ * [31:16]: wakeup timeout in ms
+ */
+ /* Pointer to extended board Data */
+ u32 hi_board_ext_data; /* 0xac */
+ u32 hi_board_ext_data_config; /* 0xb0 */
+ /*
+ * Bit [0] : valid
+ * Bit[31:16: size
+ */
+ /*
+ * hi_reset_flag is used to do some stuff when target reset.
+ * such as restore app_start after warm reset or
+ * preserve host Interest area, or preserve ROM data, literals etc.
+ */
+ u32 hi_reset_flag; /* 0xb4 */
+ /* indicate hi_reset_flag is valid */
+ u32 hi_reset_flag_valid; /* 0xb8 */
+ u32 hi_hci_uart_pwr_mgmt_params_ext; /* 0xbc */
+ /* 0xbc - [31:0]: idle timeout in ms */
+ /* ACS flags */
+ u32 hi_acs_flags; /* 0xc0 */
+ u32 hi_console_flags; /* 0xc4 */
+ u32 hi_nvram_state; /* 0xc8 */
+ u32 hi_option_flag2; /* 0xcc */
+
+ /* If non-zero, override values sent to Host in WMI_READY event. */
+ u32 hi_sw_version_override; /* 0xd0 */
+ u32 hi_abi_version_override; /* 0xd4 */
+
+ /*
+ * Percentage of high priority RX traffic to total expected RX traffic
+ * applicable only to ar6004
+ */
+ u32 hi_hp_rx_traffic_ratio; /* 0xd8 */
+
+ /* test applications flags */
+ u32 hi_test_apps_related; /* 0xdc */
+ /* location of test script */
+ u32 hi_ota_testscript; /* 0xe0 */
+ /* location of CAL data */
+ u32 hi_cal_data; /* 0xe4 */
+
+ /* Number of packet log buffers */
+ u32 hi_pktlog_num_buffers; /* 0xe8 */
+
+ /* wow extension configuration */
+ u32 hi_wow_ext_config; /* 0xec */
+ u32 hi_pwr_save_flags; /* 0xf0 */
+
+ /* Spatial Multiplexing Power Save (SMPS) options */
+ u32 hi_smps_options; /* 0xf4 */
+
+ /* Interconnect-specific state */
+ u32 hi_interconnect_state; /* 0xf8 */
+
+ /* Coex configuration flags */
+ u32 hi_coex_config; /* 0xfc */
+
+ /* Early allocation support */
+ u32 hi_early_alloc; /* 0x100 */
+ /* FW swap field */
+ /*
+ * Bits of this 32bit word will be used to pass specific swap
+ * instruction to FW
+ */
+ /*
+ * Bit 0 -- AP Nart descriptor no swap. When this bit is set
+ * FW will not swap TX descriptor. Meaning packets are formed
+ * on the target processor.
+ */
+ /* Bit 1 - unused */
+ u32 hi_fw_swap; /* 0x104 */
+} __packed;
+
+#define HI_ITEM(item) offsetof(struct host_interest, item)
+
+/* Bits defined in hi_option_flag */
+
+/* Enable timer workaround */
+#define HI_OPTION_TIMER_WAR 0x01
+/* Limit BMI command credits */
+#define HI_OPTION_BMI_CRED_LIMIT 0x02
+/* Relay Dot11 hdr to/from host */
+#define HI_OPTION_RELAY_DOT11_HDR 0x04
+/* MAC addr method 0-locally administred 1-globally unique addrs */
+#define HI_OPTION_MAC_ADDR_METHOD 0x08
+/* Firmware Bridging */
+#define HI_OPTION_FW_BRIDGE 0x10
+/* Enable CPU profiling */
+#define HI_OPTION_ENABLE_PROFILE 0x20
+/* Disable debug logging */
+#define HI_OPTION_DISABLE_DBGLOG 0x40
+/* Skip Era Tracking */
+#define HI_OPTION_SKIP_ERA_TRACKING 0x80
+/* Disable PAPRD (debug) */
+#define HI_OPTION_PAPRD_DISABLE 0x100
+#define HI_OPTION_NUM_DEV_LSB 0x200
+#define HI_OPTION_NUM_DEV_MSB 0x800
+#define HI_OPTION_DEV_MODE_LSB 0x1000
+#define HI_OPTION_DEV_MODE_MSB 0x8000000
+/* Disable LowFreq Timer Stabilization */
+#define HI_OPTION_NO_LFT_STBL 0x10000000
+/* Skip regulatory scan */
+#define HI_OPTION_SKIP_REG_SCAN 0x20000000
+/*
+ * Do regulatory scan during init before
+ * sending WMI ready event to host
+ */
+#define HI_OPTION_INIT_REG_SCAN 0x40000000
+
+/* REV6: Do not adjust memory map */
+#define HI_OPTION_SKIP_MEMMAP 0x80000000
+
+#define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
+
+/* 2 bits of hi_option_flag are used to represent 3 modes */
+#define HI_OPTION_FW_MODE_IBSS 0x0 /* IBSS Mode */
+#define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */
+#define HI_OPTION_FW_MODE_AP 0x2 /* AP Mode */
+#define HI_OPTION_FW_MODE_BT30AMP 0x3 /* BT30 AMP Mode */
+
+/* 2 bits of hi_option flag are usedto represent 4 submodes */
+#define HI_OPTION_FW_SUBMODE_NONE 0x0 /* Normal mode */
+#define HI_OPTION_FW_SUBMODE_P2PDEV 0x1 /* p2p device mode */
+#define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */
+#define HI_OPTION_FW_SUBMODE_P2PGO 0x3 /* p2p go mode */
+
+/* Num dev Mask */
+#define HI_OPTION_NUM_DEV_MASK 0x7
+#define HI_OPTION_NUM_DEV_SHIFT 0x9
+
+/* firmware bridging */
+#define HI_OPTION_FW_BRIDGE_SHIFT 0x04
+
+/*
+Fw Mode/SubMode Mask
+|-----------------------------------------------------------------------------|
+| SUB | SUB | SUB | SUB | | | | |
+|MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0]|
+| (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2) |
+|-----------------------------------------------------------------------------|
+*/
+#define HI_OPTION_FW_MODE_BITS 0x2
+#define HI_OPTION_FW_MODE_MASK 0x3
+#define HI_OPTION_FW_MODE_SHIFT 0xC
+#define HI_OPTION_ALL_FW_MODE_MASK 0xFF
+
+#define HI_OPTION_FW_SUBMODE_BITS 0x2
+#define HI_OPTION_FW_SUBMODE_MASK 0x3
+#define HI_OPTION_FW_SUBMODE_SHIFT 0x14
+#define HI_OPTION_ALL_FW_SUBMODE_MASK 0xFF00
+#define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8
+
+
+/* hi_option_flag2 options */
+#define HI_OPTION_OFFLOAD_AMSDU 0x01
+#define HI_OPTION_DFS_SUPPORT 0x02 /* Enable DFS support */
+#define HI_OPTION_ENABLE_RFKILL 0x04 /* RFKill Enable Feature*/
+#define HI_OPTION_RADIO_RETENTION_DISABLE 0x08 /* Disable radio retention */
+#define HI_OPTION_EARLY_CFG_DONE 0x10 /* Early configuration is complete */
+
+#define HI_OPTION_RF_KILL_SHIFT 0x2
+#define HI_OPTION_RF_KILL_MASK 0x1
+
+/* hi_reset_flag */
+/* preserve App Start address */
+#define HI_RESET_FLAG_PRESERVE_APP_START 0x01
+/* preserve host interest */
+#define HI_RESET_FLAG_PRESERVE_HOST_INTEREST 0x02
+/* preserve ROM data */
+#define HI_RESET_FLAG_PRESERVE_ROMDATA 0x04
+#define HI_RESET_FLAG_PRESERVE_NVRAM_STATE 0x08
+#define HI_RESET_FLAG_PRESERVE_BOOT_INFO 0x10
+#define HI_RESET_FLAG_WARM_RESET 0x20
+
+/* define hi_fw_swap bits */
+#define HI_DESC_IN_FW_BIT 0x01
+
+/* indicate the reset flag is valid */
+#define HI_RESET_FLAG_IS_VALID 0x12345678
+
+/* ACS is enabled */
+#define HI_ACS_FLAGS_ENABLED (1 << 0)
+/* Use physical WWAN device */
+#define HI_ACS_FLAGS_USE_WWAN (1 << 1)
+/* Use test VAP */
+#define HI_ACS_FLAGS_TEST_VAP (1 << 2)
+
+/*
+ * CONSOLE FLAGS
+ *
+ * Bit Range Meaning
+ * --------- --------------------------------
+ * 2..0 UART ID (0 = Default)
+ * 3 Baud Select (0 = 9600, 1 = 115200)
+ * 30..4 Reserved
+ * 31 Enable Console
+ *
+ */
+
+#define HI_CONSOLE_FLAGS_ENABLE (1 << 31)
+#define HI_CONSOLE_FLAGS_UART_MASK (0x7)
+#define HI_CONSOLE_FLAGS_UART_SHIFT 0
+#define HI_CONSOLE_FLAGS_BAUD_SELECT (1 << 3)
+
+/* SM power save options */
+#define HI_SMPS_ALLOW_MASK (0x00000001)
+#define HI_SMPS_MODE_MASK (0x00000002)
+#define HI_SMPS_MODE_STATIC (0x00000000)
+#define HI_SMPS_MODE_DYNAMIC (0x00000002)
+#define HI_SMPS_DISABLE_AUTO_MODE (0x00000004)
+#define HI_SMPS_DATA_THRESH_MASK (0x000007f8)
+#define HI_SMPS_DATA_THRESH_SHIFT (3)
+#define HI_SMPS_RSSI_THRESH_MASK (0x0007f800)
+#define HI_SMPS_RSSI_THRESH_SHIFT (11)
+#define HI_SMPS_LOWPWR_CM_MASK (0x00380000)
+#define HI_SMPS_LOWPWR_CM_SHIFT (15)
+#define HI_SMPS_HIPWR_CM_MASK (0x03c00000)
+#define HI_SMPS_HIPWR_CM_SHIFT (19)
+
+/*
+ * WOW Extension configuration
+ *
+ * Bit Range Meaning
+ * --------- --------------------------------
+ * 8..0 Size of each WOW pattern (max 511)
+ * 15..9 Number of patterns per list (max 127)
+ * 17..16 Number of lists (max 4)
+ * 30..18 Reserved
+ * 31 Enabled
+ *
+ * set values (except enable) to zeros for default settings
+ */
+
+#define HI_WOW_EXT_ENABLED_MASK (1 << 31)
+#define HI_WOW_EXT_NUM_LIST_SHIFT 16
+#define HI_WOW_EXT_NUM_LIST_MASK (0x3 << HI_WOW_EXT_NUM_LIST_SHIFT)
+#define HI_WOW_EXT_NUM_PATTERNS_SHIFT 9
+#define HI_WOW_EXT_NUM_PATTERNS_MASK (0x7F << HI_WOW_EXT_NUM_PATTERNS_SHIFT)
+#define HI_WOW_EXT_PATTERN_SIZE_SHIFT 0
+#define HI_WOW_EXT_PATTERN_SIZE_MASK (0x1FF << HI_WOW_EXT_PATTERN_SIZE_SHIFT)
+
+#define HI_WOW_EXT_MAKE_CONFIG(num_lists, count, size) \
+ ((((num_lists) << HI_WOW_EXT_NUM_LIST_SHIFT) & \
+ HI_WOW_EXT_NUM_LIST_MASK) | \
+ (((count) << HI_WOW_EXT_NUM_PATTERNS_SHIFT) & \
+ HI_WOW_EXT_NUM_PATTERNS_MASK) | \
+ (((size) << HI_WOW_EXT_PATTERN_SIZE_SHIFT) & \
+ HI_WOW_EXT_PATTERN_SIZE_MASK))
+
+#define HI_WOW_EXT_GET_NUM_LISTS(config) \
+ (((config) & HI_WOW_EXT_NUM_LIST_MASK) >> HI_WOW_EXT_NUM_LIST_SHIFT)
+#define HI_WOW_EXT_GET_NUM_PATTERNS(config) \
+ (((config) & HI_WOW_EXT_NUM_PATTERNS_MASK) >> \
+ HI_WOW_EXT_NUM_PATTERNS_SHIFT)
+#define HI_WOW_EXT_GET_PATTERN_SIZE(config) \
+ (((config) & HI_WOW_EXT_PATTERN_SIZE_MASK) >> \
+ HI_WOW_EXT_PATTERN_SIZE_SHIFT)
+
+/*
+ * Early allocation configuration
+ * Support RAM bank configuration before BMI done and this eases the memory
+ * allocation at very early stage
+ * Bit Range Meaning
+ * --------- ----------------------------------
+ * [0:3] number of bank assigned to be IRAM
+ * [4:15] reserved
+ * [16:31] magic number
+ *
+ * Note:
+ * 1. target firmware would check magic number and if it's a match, firmware
+ * would consider the bits[0:15] are valid and base on that to calculate
+ * the end of DRAM. Early allocation would be located at that area and
+ * may be reclaimed when necesary
+ * 2. if no magic number is found, early allocation would happen at "_end"
+ * symbol of ROM which is located before the app-data and might NOT be
+ * re-claimable. If this is adopted, link script should keep this in
+ * mind to avoid data corruption.
+ */
+#define HI_EARLY_ALLOC_MAGIC 0x6d8a
+#define HI_EARLY_ALLOC_MAGIC_MASK 0xffff0000
+#define HI_EARLY_ALLOC_MAGIC_SHIFT 16
+#define HI_EARLY_ALLOC_IRAM_BANKS_MASK 0x0000000f
+#define HI_EARLY_ALLOC_IRAM_BANKS_SHIFT 0
+
+#define HI_EARLY_ALLOC_VALID() \
+ ((((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_MAGIC_MASK) >> \
+ HI_EARLY_ALLOC_MAGIC_SHIFT) == (HI_EARLY_ALLOC_MAGIC))
+#define HI_EARLY_ALLOC_GET_IRAM_BANKS() \
+ (((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_IRAM_BANKS_MASK) \
+ >> HI_EARLY_ALLOC_IRAM_BANKS_SHIFT)
+
+/*power save flag bit definitions*/
+#define HI_PWR_SAVE_LPL_ENABLED 0x1
+/*b1-b3 reserved*/
+/*b4-b5 : dev0 LPL type : 0 - none
+ 1- Reduce Pwr Search
+ 2- Reduce Pwr Listen*/
+/*b6-b7 : dev1 LPL type and so on for Max 8 devices*/
+#define HI_PWR_SAVE_LPL_DEV0_LSB 4
+#define HI_PWR_SAVE_LPL_DEV_MASK 0x3
+/*power save related utility macros*/
+#define HI_LPL_ENABLED() \
+ ((HOST_INTEREST->hi_pwr_save_flags & HI_PWR_SAVE_LPL_ENABLED))
+#define HI_DEV_LPL_TYPE_GET(_devix) \
+ (HOST_INTEREST->hi_pwr_save_flags & ((HI_PWR_SAVE_LPL_DEV_MASK) << \
+ (HI_PWR_SAVE_LPL_DEV0_LSB + (_devix)*2)))
+
+#define HOST_INTEREST_SMPS_IS_ALLOWED() \
+ ((HOST_INTEREST->hi_smps_options & HI_SMPS_ALLOW_MASK))
+
+/* Reserve 1024 bytes for extended board data */
+#define QCA988X_BOARD_DATA_SZ 7168
+#define QCA988X_BOARD_EXT_DATA_SZ 0
+
+#endif /* __TARGADDRS_H__ */
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
