This is needed to make DFS regulatory domain support work again. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@xxxxxxxxxxx> --- nl80211.h | 1207 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++----- 1 files changed, 1110 insertions(+), 97 deletions(-) diff --git a/nl80211.h b/nl80211.h index 2dbb799..79da871 100644 --- a/nl80211.h +++ b/nl80211.h @@ -36,7 +36,21 @@ * The station is still assumed to belong to the AP interface it was added * to. * - * TODO: need more info? + * Station handling varies per interface type and depending on the driver's + * capabilities. + * + * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS + * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows: + * - a setup station entry is added, not yet authorized, without any rate + * or capability information, this just exists to avoid race conditions + * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid + * to add rate and capability information to the station and at the same + * time mark it authorized. + * - %NL80211_TDLS_ENABLE_LINK is then used + * - after this, the only valid operation is to remove it by tearing down + * the TDLS link (%NL80211_TDLS_DISABLE_LINK) + * + * TODO: need more info for other interface types */ /** @@ -118,8 +132,9 @@ * to get a list of all present wiphys. * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME, - * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ, - * %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT, + * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the + * attributes determining the channel width; this is used for setting + * monitor mode channel), %NL80211_ATTR_WIPHY_RETRY_SHORT, * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD, * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD. * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL @@ -156,21 +171,26 @@ * @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX * or %NL80211_ATTR_MAC. * - * @NL80211_CMD_GET_BEACON: retrieve beacon information (returned in a - * %NL80222_CMD_NEW_BEACON message) - * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface - * using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD, - * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes. - * Following attributes are provided for drivers that generate full Beacon - * and Probe Response frames internally: %NL80211_ATTR_SSID, + * @NL80211_CMD_GET_BEACON: (not used) + * @NL80211_CMD_SET_BEACON: change the beacon on an access point interface + * using the %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL + * attributes. For drivers that generate the beacon and probe responses + * internally, the following attributes must be provided: %NL80211_ATTR_IE, + * %NL80211_ATTR_IE_PROBE_RESP and %NL80211_ATTR_IE_ASSOC_RESP. + * @NL80211_CMD_START_AP: Start AP operation on an AP interface, parameters + * are like for %NL80211_CMD_SET_BEACON, and additionally parameters that + * do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL, + * %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID, * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE, * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, - * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP, - * %NL80211_ATTR_IE_ASSOC_RESP. - * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface, - * parameters are like for %NL80211_CMD_SET_BEACON. - * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it + * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT, + * %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS. + * The channel to use can be set on the interface or be given using the + * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width. + * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP + * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface + * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP * * @NL80211_CMD_GET_STATION: Get station attributes for station identified by * %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX. @@ -273,6 +293,12 @@ * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to * NL80211_CMD_GET_SURVEY and on the "scan" multicast group) * + * @NL80211_CMD_SET_PMKSA: Add a PMKSA cache entry, using %NL80211_ATTR_MAC + * (for the BSSID) and %NL80211_ATTR_PMKID. + * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC + * (for the BSSID) and %NL80211_ATTR_PMKID. + * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries. + * * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain * has been changed and provides details of the request information * that caused the change such as who initiated the regulatory request @@ -363,10 +389,15 @@ * requests to connect to a specified network but without separating * auth and assoc steps. For this, you need to specify the SSID in a * %NL80211_ATTR_SSID attribute, and can optionally specify the association - * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC, - * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, + * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP, + * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. + * Background scan period can optionally be + * specified in %NL80211_ATTR_BG_SCAN_PERIOD, + * if not specified default background scan configuration + * in driver is used and if period value is 0, bg scan will be disabled. + * This attribute is ignored if driver does not support roam scan. * It is also sent as an event, with the BSSID and response IEs when the * connection is established or failed to be established. This can be * determined by the STATUS_CODE attribute. @@ -386,8 +417,7 @@ * a response while being associated to an AP on another channel. * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the - * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be - * optionally used to specify additional channel parameters. + * frequency for the operation. * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds * to remain on the channel. This command is also used as an event to * notify when the requested duration starts (it may take a while for the @@ -425,12 +455,11 @@ * as an event indicating reception of a frame that was not processed in * kernel code, but is for us (i.e., which may need to be processed in a * user space application). %NL80211_ATTR_FRAME is used to specify the - * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and - * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on - * which channel the frame is to be transmitted or was received. If this - * channel is not the current channel (remain-on-channel or the - * operational channel) the device will switch to the given channel and - * transmit the frame, optionally waiting for a response for the time + * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ is used + * to indicate on which channel the frame is to be transmitted or was + * received. If this channel is not the current channel (remain-on-channel + * or the operational channel) the device will switch to the given channel + * and transmit the frame, optionally waiting for a response for the time * specified using %NL80211_ATTR_DURATION. When called, this operation * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the * TX status event pertaining to the TX request. @@ -447,6 +476,10 @@ * the frame. * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for * backward compatibility. + * + * @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE + * @NL80211_CMD_GET_POWER_SAVE: Get powersave status in %NL80211_ATTR_PS_STATE + * * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command * is used to configure connection quality monitoring notification trigger * levels. @@ -454,8 +487,8 @@ * command is used as an event to indicate the that a trigger level was * reached. * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ - * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed - * by %NL80211_ATTR_IFINDEX) shall operate on. + * and the attributes determining channel width) the given interface + * (identifed by %NL80211_ATTR_IFINDEX) shall operate on. * In case multiple channels are supported by the device, the mechanism * with which it switches channels is implementation-defined. * When a monitor interface is given, it can only switch channel while @@ -480,9 +513,11 @@ * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a * beacon or probe response from a compatible mesh peer. This is only * sent while no station information (sta_info) exists for the new peer - * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On - * reception of this notification, userspace may decide to create a new - * station (@NL80211_CMD_NEW_STATION). To stop this notification from + * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH, + * @NL80211_MESH_SETUP_USERSPACE_AMPE, or + * @NL80211_MESH_SETUP_USERSPACE_MPM is set. On reception of this + * notification, userspace may decide to create a new station + * (@NL80211_CMD_NEW_STATION). To stop this notification from * reoccurring, the userspace authentication daemon may want to create the * new station with the AUTHENTICATED flag unset and maybe change it later * depending on the authentication result. @@ -494,6 +529,12 @@ * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For * more background information, see * http://wireless.kernel.org/en/users/Documentation/WoWLAN. + * The @NL80211_CMD_SET_WOWLAN command can also be used as a notification + * from the driver reporting the wakeup reason. In this case, the + * @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason + * for the wakeup, if it was caused by wireless. If it is not present + * in the wakeup notification, the wireless device didn't cause the + * wakeup but reports that it was woken up. * * @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver * the necessary information for supporting GTK rekey offload. This @@ -507,8 +548,97 @@ * of PMKSA caching dandidates. * * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup). + * In addition, this can be used as an event to request userspace to take + * actions on TDLS links (set up a new link or tear down an existing one). + * In such events, %NL80211_ATTR_TDLS_OPERATION indicates the requested + * operation, %NL80211_ATTR_MAC contains the peer MAC address, and + * %NL80211_ATTR_REASON_CODE the reason code to be used (only with + * %NL80211_TDLS_TEARDOWN). * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. * + * @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP + * (or GO) interface (i.e. hostapd) to ask for unexpected frames to + * implement sending deauth to stations that send unexpected class 3 + * frames. Also used as the event sent by the kernel when such a frame + * is received. + * For the event, the %NL80211_ATTR_MAC attribute carries the TA and + * other attributes like the interface index are present. + * If used as the command it must have an interface index and you can + * only unsubscribe from the event by closing the socket. Subscription + * is also for %NL80211_CMD_UNEXPECTED_4ADDR_FRAME events. + * + * @NL80211_CMD_UNEXPECTED_4ADDR_FRAME: Sent as an event indicating that the + * associated station identified by %NL80211_ATTR_MAC sent a 4addr frame + * and wasn't already in a 4-addr VLAN. The event will be sent similarly + * to the %NL80211_CMD_UNEXPECTED_FRAME event, to the same listener. + * + * @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface + * by sending a null data frame to it and reporting when the frame is + * acknowleged. This is used to allow timing out inactive clients. Uses + * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a + * direct reply with an %NL80211_ATTR_COOKIE that is later used to match + * up the event with the request. The event includes the same data and + * has %NL80211_ATTR_ACK set if the frame was ACKed. + * + * @NL80211_CMD_REGISTER_BEACONS: Register this socket to receive beacons from + * other BSSes when any interfaces are in AP mode. This helps implement + * OLBC handling in hostapd. Beacons are reported in %NL80211_CMD_FRAME + * messages. Note that per PHY only one application may register. + * + * @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether + * No Acknowledgement Policy should be applied. + * + * @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels + * independently of the userspace SME, send this event indicating + * %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ and the + * attributes determining channel width. + * + * @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by + * its %NL80211_ATTR_WDEV identifier. It must have been created with + * %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the + * P2P Device can be used for P2P operations, e.g. remain-on-channel and + * public action frame TX. + * @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by + * its %NL80211_ATTR_WDEV identifier. + * + * @NL80211_CMD_CONN_FAILED: connection request to an AP failed; used to + * notify userspace that AP has rejected the connection request from a + * station, due to particular reason. %NL80211_ATTR_CONN_FAILED_REASON + * is used for this. + * + * @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames + * for IBSS or MESH vif. + * + * @NL80211_CMD_SET_MAC_ACL: sets ACL for MAC address based access control. + * This is to be used with the drivers advertising the support of MAC + * address based access control. List of MAC addresses is passed in + * %NL80211_ATTR_MAC_ADDRS and ACL policy is passed in + * %NL80211_ATTR_ACL_POLICY. Driver will enable ACL with this list, if it + * is not already done. The new list will replace any existing list. Driver + * will clear its ACL when the list of MAC addresses passed is empty. This + * command is used in AP/P2P GO mode. Driver has to make sure to clear its + * ACL list during %NL80211_CMD_STOP_AP. + * + * @NL80211_CMD_RADAR_DETECT: Start a Channel availability check (CAC). Once + * a radar is detected or the channel availability scan (CAC) has finished + * or was aborted, or a radar was detected, usermode will be notified with + * this event. This command is also used to notify userspace about radars + * while operating on this channel. + * %NL80211_ATTR_RADAR_EVENT is used to inform about the type of the + * event. + * + * @NL80211_CMD_GET_PROTOCOL_FEATURES: Get global nl80211 protocol features, + * i.e. features for the nl80211 protocol rather than device features. + * Returns the features in the %NL80211_ATTR_PROTOCOL_FEATURES bitmap. + * + * @NL80211_CMD_UPDATE_FT_IES: Pass down the most up-to-date Fast Transition + * Information Element to the WLAN driver + * + * @NL80211_CMD_FT_EVENT: Send a Fast transition event from the WLAN driver + * to the supplicant. This will carry the target AP's MAC address along + * with the relevant Information Elements. This event is used to report + * received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE). + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -533,8 +663,10 @@ enum nl80211_commands { NL80211_CMD_GET_BEACON, NL80211_CMD_SET_BEACON, - NL80211_CMD_NEW_BEACON, - NL80211_CMD_DEL_BEACON, + NL80211_CMD_START_AP, + NL80211_CMD_NEW_BEACON = NL80211_CMD_START_AP, + NL80211_CMD_STOP_AP, + NL80211_CMD_DEL_BEACON = NL80211_CMD_STOP_AP, NL80211_CMD_GET_STATION, NL80211_CMD_SET_STATION, @@ -638,6 +770,34 @@ enum nl80211_commands { NL80211_CMD_TDLS_OPER, NL80211_CMD_TDLS_MGMT, + NL80211_CMD_UNEXPECTED_FRAME, + + NL80211_CMD_PROBE_CLIENT, + + NL80211_CMD_REGISTER_BEACONS, + + NL80211_CMD_UNEXPECTED_4ADDR_FRAME, + + NL80211_CMD_SET_NOACK_MAP, + + NL80211_CMD_CH_SWITCH_NOTIFY, + + NL80211_CMD_START_P2P_DEVICE, + NL80211_CMD_STOP_P2P_DEVICE, + + NL80211_CMD_CONN_FAILED, + + NL80211_CMD_SET_MCAST_RATE, + + NL80211_CMD_SET_MAC_ACL, + + NL80211_CMD_RADAR_DETECT, + + NL80211_CMD_GET_PROTOCOL_FEATURES, + + NL80211_CMD_UPDATE_FT_IES, + NL80211_CMD_FT_EVENT, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -658,6 +818,8 @@ enum nl80211_commands { #define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE #define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT +#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS + /* source-level API compatibility */ #define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG #define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG @@ -672,14 +834,26 @@ enum nl80211_commands { * /sys/class/ieee80211/<phyname>/index * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming) * @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters - * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz + * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz, + * defines the channel together with the (deprecated) + * %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes + * %NL80211_ATTR_CHANNEL_WIDTH and if needed %NL80211_ATTR_CENTER_FREQ1 + * and %NL80211_ATTR_CENTER_FREQ2 + * @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values + * of &enum nl80211_chan_width, describing the channel width. See the + * documentation of the enum for more information. + * @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the + * channel, used for anything but 20 MHz bandwidth + * @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the + * channel, used only for 80+80 MHz bandwidth * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ - * if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included): + * if HT20 or HT40 are to be used (i.e., HT disabled if not included): * NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including * this attribute) * NL80211_CHAN_HT20 = HT20 only * NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel * NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel + * This attribute is now deprecated. * @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is * less than or equal to the RTS threshold; allowed range: 1..255; * dot11ShortRetryLimit; u8 @@ -699,6 +873,9 @@ enum nl80211_commands { * @NL80211_ATTR_IFNAME: network interface name * @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype * + * @NL80211_ATTR_WDEV: wireless device identifier, used for pseudo-devices + * that don't have a netdev (u64) + * * @NL80211_ATTR_MAC: MAC address (various uses) * * @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of @@ -709,6 +886,13 @@ enum nl80211_commands { * section 7.3.2.25.1, e.g. 0x000FAC04) * @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and * CCMP keys, each six bytes in little endian + * @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key + * @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the + * default management key + * @NL80211_ATTR_CIPHER_SUITES_PAIRWISE: For crypto settings for connect or + * other commands, indicates which pairwise cipher suites are used + * @NL80211_ATTR_CIPHER_SUITE_GROUP: For crypto settings for connect or + * other commands, indicates which group cipher suite is used * * @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU * @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing @@ -733,7 +917,8 @@ enum nl80211_commands { * consisting of a nested array. * * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes). - * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link. + * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link + * (see &enum nl80211_plink_action). * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path. * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path * info given for %NL80211_CMD_GET_MPATH, nested attribute described at @@ -836,7 +1021,7 @@ enum nl80211_commands { * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is * used for the association (&enum nl80211_mfp, represented as a u32); * this attribute can be used - * with %NL80211_CMD_ASSOCIATE request + * with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests * * @NL80211_ATTR_STA_FLAGS2: Attribute containing a * &struct nl80211_sta_flag_update. @@ -944,6 +1129,8 @@ enum nl80211_commands { * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was * acknowledged by the recipient. * + * @NL80211_ATTR_PS_STATE: powersave state, using &enum nl80211_ps_state values. + * * @NL80211_ATTR_CQM: connection quality monitor configuration in a * nested attribute with %NL80211_ATTR_CQM_* sub-attributes. * @@ -1001,7 +1188,7 @@ enum nl80211_commands { * flag isn't set, the frame will be rejected. This is also used as an * nl80211 capability flag. * - * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16) + * @NL80211_ATTR_BSS_HT_OPMODE: HT operation mode (u16) * * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags * attributes, specifying what a key should be set as default as. @@ -1014,10 +1201,10 @@ enum nl80211_commands { * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver * allows auth frames in a mesh to be passed to userspace for processing via * the @NL80211_MESH_SETUP_USERSPACE_AUTH flag. - * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as - * defined in &enum nl80211_plink_state. Used when userspace is - * driving the peer link management state machine. - * @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled. + * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as defined in + * &enum nl80211_plink_state. Used when userspace is driving the peer link + * management state machine. @NL80211_MESH_SETUP_USERSPACE_AMPE or + * @NL80211_MESH_SETUP_USERSPACE_MPM must be enabled. * * @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy * capabilities, the supported WoWLAN triggers @@ -1025,10 +1212,10 @@ enum nl80211_commands { * indicate which WoW triggers should be enabled. This is also * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN * triggers. - + * * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan * cycles, in msecs. - + * * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more * sets of attributes to match during scheduled scans. Only BSSs * that match any of the sets will be reported. These are @@ -1055,7 +1242,7 @@ enum nl80211_commands { * are managed in software: interfaces of these types aren't subject to * any restrictions in their number or combinations. * - * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information + * @NL80211_ATTR_REKEY_DATA: nested attribute containing the information * necessary for GTK rekeying in the device, see &enum nl80211_rekey_data. * * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan, @@ -1109,10 +1296,124 @@ enum nl80211_commands { * %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be * used for asking the driver to perform a TDLS operation. * + * @NL80211_ATTR_DEVICE_AP_SME: This u32 attribute may be listed for devices + * that have AP support to indicate that they have the AP SME integrated + * with support for the features listed in this attribute, see + * &enum nl80211_ap_sme_features. + * + * @NL80211_ATTR_DONT_WAIT_FOR_ACK: Used with %NL80211_CMD_FRAME, this tells + * the driver to not wait for an acknowledgement. Note that due to this, + * it will also not give a status callback nor return a cookie. This is + * mostly useful for probe responses to save airtime. + * + * @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from + * &enum nl80211_feature_flags and is advertised in wiphy information. + * @NL80211_ATTR_PROBE_RESP_OFFLOAD: Indicates that the HW responds to probe + * requests while operating in AP-mode. + * This attribute holds a bitmap of the supported protocols for + * offloading (see &enum nl80211_probe_resp_offload_support_attr). + * + * @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire + * probe-response frame. The DA field in the 802.11 header is zero-ed out, + * to be filled by the FW. + * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable + * this feature. Currently, only supported in mac80211 drivers. + * @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the + * ATTR_HT_CAPABILITY to which attention should be paid. + * Currently, only mac80211 NICs support this feature. + * The values that may be configured are: + * MCS rates, MAX-AMSDU, HT-20-40 and HT_CAP_SGI_40 + * AMPDU density and AMPDU factor. + * All values are treated as suggestions and may be ignored + * by the driver as required. The actual values may be seen in + * the station debugfs ht_caps file. + * * @NL80211_ATTR_DFS_REGION: region for regulatory rules which this country * abides to when initiating radiation on DFS channels. A country maps * to one DFS region. * + * @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of + * up to 16 TIDs. + * + * @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be + * used by the drivers which has MLME in firmware and does not have support + * to report per station tx/rx activity to free up the staion entry from + * the list. This needs to be used when the driver advertises the + * capability to timeout the stations. + * + * @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int); + * this attribute is (depending on the driver capabilities) added to + * received frames indicated with %NL80211_CMD_FRAME. + * + * @NL80211_ATTR_BG_SCAN_PERIOD: Background scan period in seconds + * or 0 to disable background scan. + * + * @NL80211_ATTR_USER_REG_HINT_TYPE: type of regulatory hint passed from + * userspace. If unset it is assumed the hint comes directly from + * a user. If set code could specify exactly what type of source + * was used to provide the hint. For the different types of + * allowed user regulatory hints see nl80211_user_reg_hint_type. + * + * @NL80211_ATTR_CONN_FAILED_REASON: The reason for which AP has rejected + * the connection request from a station. nl80211_connect_failed_reason + * enum has different reasons of connection failure. + * + * @NL80211_ATTR_SAE_DATA: SAE elements in Authentication frames. This starts + * with the Authentication transaction sequence number field. + * + * @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from + * association request when used with NL80211_CMD_NEW_STATION) + * + * @NL80211_ATTR_SCAN_FLAGS: scan request control flags (u32) + * + * @NL80211_ATTR_P2P_CTWINDOW: P2P GO Client Traffic Window (u8), used with + * the START_AP and SET_BSS commands + * @NL80211_ATTR_P2P_OPPPS: P2P GO opportunistic PS (u8), used with the + * START_AP and SET_BSS commands. This can have the values 0 or 1; + * if not given in START_AP 0 is assumed, if not given in SET_BSS + * no change is made. + * + * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode + * defined in &enum nl80211_mesh_power_mode. + * + * @NL80211_ATTR_ACL_POLICY: ACL policy, see &enum nl80211_acl_policy, + * carried in a u32 attribute + * + * @NL80211_ATTR_MAC_ADDRS: Array of nested MAC addresses, used for + * MAC ACL. + * + * @NL80211_ATTR_MAC_ACL_MAX: u32 attribute to advertise the maximum + * number of MAC addresses that a device can support for MAC + * ACL. + * + * @NL80211_ATTR_RADAR_EVENT: Type of radar event for notification to userspace, + * contains a value of enum nl80211_radar_event (u32). + * + * @NL80211_ATTR_EXT_CAPA: 802.11 extended capabilities that the kernel driver + * has and handles. The format is the same as the IE contents. See + * 802.11-2012 8.4.2.29 for more information. + * @NL80211_ATTR_EXT_CAPA_MASK: Extended capabilities that the kernel driver + * has set in the %NL80211_ATTR_EXT_CAPA value, for multibit fields. + * + * @NL80211_ATTR_STA_CAPABILITY: Station capabilities (u16) are advertised to + * the driver, e.g., to enable TDLS power save (PU-APSD). + * + * @NL80211_ATTR_STA_EXT_CAPABILITY: Station extended capabilities are + * advertised to the driver, e.g., to enable TDLS off channel operations + * and PU-APSD. + * + * @NL80211_ATTR_PROTOCOL_FEATURES: global nl80211 feature flags, see + * &enum nl80211_protocol_features, the attribute is a u32. + * + * @NL80211_ATTR_SPLIT_WIPHY_DUMP: flag attribute, userspace supports + * receiving the data for a single wiphy split across multiple + * messages, given with wiphy dump message + * + * @NL80211_ATTR_MDID: Mobility Domain Identifier + * + * @NL80211_ATTR_IE_RIC: Resource Information Container Information + * Element + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1341,8 +1642,73 @@ enum nl80211_attrs { NL80211_ATTR_TDLS_SUPPORT, NL80211_ATTR_TDLS_EXTERNAL_SETUP, + NL80211_ATTR_DEVICE_AP_SME, + + NL80211_ATTR_DONT_WAIT_FOR_ACK, + + NL80211_ATTR_FEATURE_FLAGS, + + NL80211_ATTR_PROBE_RESP_OFFLOAD, + + NL80211_ATTR_PROBE_RESP, + NL80211_ATTR_DFS_REGION, + NL80211_ATTR_DISABLE_HT, + NL80211_ATTR_HT_CAPABILITY_MASK, + + NL80211_ATTR_NOACK_MAP, + + NL80211_ATTR_INACTIVITY_TIMEOUT, + + NL80211_ATTR_RX_SIGNAL_DBM, + + NL80211_ATTR_BG_SCAN_PERIOD, + + NL80211_ATTR_WDEV, + + NL80211_ATTR_USER_REG_HINT_TYPE, + + NL80211_ATTR_CONN_FAILED_REASON, + + NL80211_ATTR_SAE_DATA, + + NL80211_ATTR_VHT_CAPABILITY, + + NL80211_ATTR_SCAN_FLAGS, + + NL80211_ATTR_CHANNEL_WIDTH, + NL80211_ATTR_CENTER_FREQ1, + NL80211_ATTR_CENTER_FREQ2, + + NL80211_ATTR_P2P_CTWINDOW, + NL80211_ATTR_P2P_OPPPS, + + NL80211_ATTR_LOCAL_MESH_POWER_MODE, + + NL80211_ATTR_ACL_POLICY, + + NL80211_ATTR_MAC_ADDRS, + + NL80211_ATTR_MAC_ACL_MAX, + + NL80211_ATTR_RADAR_EVENT, + + NL80211_ATTR_EXT_CAPA, + NL80211_ATTR_EXT_CAPA_MASK, + + NL80211_ATTR_STA_CAPABILITY, + NL80211_ATTR_STA_EXT_CAPABILITY, + + NL80211_ATTR_PROTOCOL_FEATURES, + NL80211_ATTR_SPLIT_WIPHY_DUMP, + + NL80211_ATTR_DISABLE_VHT, + NL80211_ATTR_VHT_CAPABILITY_MASK, + + NL80211_ATTR_MDID, + NL80211_ATTR_IE_RIC, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1377,17 +1743,27 @@ enum nl80211_attrs { #define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES #define NL80211_ATTR_KEY NL80211_ATTR_KEY #define NL80211_ATTR_KEYS NL80211_ATTR_KEYS +#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS #define NL80211_MAX_SUPP_RATES 32 +#define NL80211_MAX_SUPP_HT_RATES 77 #define NL80211_MAX_SUPP_REG_RULES 32 #define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0 #define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16 #define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24 #define NL80211_HT_CAPABILITY_LEN 26 +#define NL80211_VHT_CAPABILITY_LEN 12 #define NL80211_MAX_NR_CIPHER_SUITES 5 #define NL80211_MAX_NR_AKM_SUITES 2 +#define NL80211_MIN_REMAIN_ON_CHANNEL_TIME 10 + +/* default RSSI threshold for scan results if none specified. */ +#define NL80211_SCAN_RSSI_THOLD_OFF -300 + +#define NL80211_CQM_TXE_MAX_INTVL 1800 + /** * enum nl80211_iftype - (virtual) interface types * @@ -1403,6 +1779,10 @@ enum nl80211_attrs { * @NL80211_IFTYPE_MESH_POINT: mesh point * @NL80211_IFTYPE_P2P_CLIENT: P2P client * @NL80211_IFTYPE_P2P_GO: P2P group owner + * @NL80211_IFTYPE_P2P_DEVICE: P2P device interface type, this is not a netdev + * and therefore can't be created in the normal ways, use the + * %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE + * commands to create and destroy one * @NL80211_IFTYPE_MAX: highest interface type number currently defined * @NUM_NL80211_IFTYPES: number of defined interface types * @@ -1421,6 +1801,7 @@ enum nl80211_iftype { NL80211_IFTYPE_MESH_POINT, NL80211_IFTYPE_P2P_CLIENT, NL80211_IFTYPE_P2P_GO, + NL80211_IFTYPE_P2P_DEVICE, /* keep last */ NUM_NL80211_IFTYPES, @@ -1440,7 +1821,14 @@ enum nl80211_iftype { * @NL80211_STA_FLAG_WME: station is WME/QoS capable * @NL80211_STA_FLAG_MFP: station uses management frame protection * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated - * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer + * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should + * only be used in managed mode (even in the flags mask). Note that the + * flag can't be changed, it is only valid while adding a station, and + * attempts to change it will silently be ignored (rather than rejected + * as errors.) + * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers + * that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a + * previously added station into associated state * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ @@ -1452,12 +1840,15 @@ enum nl80211_sta_flags { NL80211_STA_FLAG_MFP, NL80211_STA_FLAG_AUTHENTICATED, NL80211_STA_FLAG_TDLS_PEER, + NL80211_STA_FLAG_ASSOCIATED, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1 }; +#define NL80211_STA_FLAG_MAX_OLD_API NL80211_STA_FLAG_TDLS_PEER + /** * struct nl80211_sta_flag_update - station flags mask/set * @mask: mask of station flags to set @@ -1475,13 +1866,26 @@ struct nl80211_sta_flag_update { * * These attribute types are used with %NL80211_STA_INFO_TXRATE * when getting information about the bitrate of a station. + * There are 2 attributes for bitrate, a legacy one that represents + * a 16-bit value, and new one that represents a 32-bit value. + * If the rate value fits into 16 bit, both attributes are reported + * with the same value. If the rate is too high to fit into 16 bits + * (>6.5535Gbps) only 32-bit attribute is included. + * User space tools encouraged to use the 32-bit attribute and fall + * back to the 16-bit one for compatibility with older kernels. * * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s) * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8) - * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate + * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 MHz dualchannel bitrate * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval + * @NL80211_RATE_INFO_BITRATE32: total bitrate (u32, 100kbit/s) * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined + * @NL80211_RATE_INFO_VHT_MCS: MCS index for VHT (u8) + * @NL80211_RATE_INFO_VHT_NSS: number of streams in VHT (u8) + * @NL80211_RATE_INFO_80_MHZ_WIDTH: 80 MHz VHT rate + * @NL80211_RATE_INFO_80P80_MHZ_WIDTH: 80+80 MHz VHT rate + * @NL80211_RATE_INFO_160_MHZ_WIDTH: 160 MHz VHT rate * @__NL80211_RATE_INFO_AFTER_LAST: internal use */ enum nl80211_rate_info { @@ -1490,6 +1894,12 @@ enum nl80211_rate_info { NL80211_RATE_INFO_MCS, NL80211_RATE_INFO_40_MHZ_WIDTH, NL80211_RATE_INFO_SHORT_GI, + NL80211_RATE_INFO_BITRATE32, + NL80211_RATE_INFO_VHT_MCS, + NL80211_RATE_INFO_VHT_NSS, + NL80211_RATE_INFO_80_MHZ_WIDTH, + NL80211_RATE_INFO_80P80_MHZ_WIDTH, + NL80211_RATE_INFO_160_MHZ_WIDTH, /* keep last */ __NL80211_RATE_INFO_AFTER_LAST, @@ -1536,6 +1946,8 @@ enum nl80211_sta_bss_param { * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs) * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station) * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station) + * @NL80211_STA_INFO_RX_BYTES64: total received bytes (u64, from this station) + * @NL80211_STA_INFO_TX_BYTES64: total transmitted bytes (u64, to this station) * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm) * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute * containing info as possible, see &enum nl80211_rate_info @@ -1554,6 +1966,13 @@ enum nl80211_sta_bss_param { * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute * containing info as possible, see &enum nl80211_sta_bss_param * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected + * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update. + * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32) + * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64) + * @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode + * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode + * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards + * non-peer STA * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -1575,6 +1994,14 @@ enum nl80211_sta_info { NL80211_STA_INFO_RX_BITRATE, NL80211_STA_INFO_BSS_PARAM, NL80211_STA_INFO_CONNECTED_TIME, + NL80211_STA_INFO_STA_FLAGS, + NL80211_STA_INFO_BEACON_LOSS, + NL80211_STA_INFO_T_OFFSET, + NL80211_STA_INFO_LOCAL_PM, + NL80211_STA_INFO_PEER_PM, + NL80211_STA_INFO_NONPEER_PM, + NL80211_STA_INFO_RX_BYTES64, + NL80211_STA_INFO_TX_BYTES64, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -1644,6 +2071,9 @@ enum nl80211_mpath_info { * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n + * @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as + * defined in 802.11ac + * @NL80211_BAND_ATTR_VHT_CAPA: VHT capabilities, as in the HT information IE * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined * @__NL80211_BAND_ATTR_AFTER_LAST: internal use */ @@ -1657,6 +2087,9 @@ enum nl80211_band_attr { NL80211_BAND_ATTR_HT_AMPDU_FACTOR, NL80211_BAND_ATTR_HT_AMPDU_DENSITY, + NL80211_BAND_ATTR_VHT_MCS_SET, + NL80211_BAND_ATTR_VHT_CAPA, + /* keep last */ __NL80211_BAND_ATTR_AFTER_LAST, NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1 @@ -1678,6 +2111,20 @@ enum nl80211_band_attr { * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm * (100 * dBm). + * @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS + * (enum nl80211_dfs_state) + * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long + * this channel is in this DFS state. + * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this + * channel as the control channel + * @NL80211_FREQUENCY_ATTR_NO_HT40_PLUS: HT40+ isn't possible with this + * channel as the control channel + * @NL80211_FREQUENCY_ATTR_NO_80MHZ: any 80 MHz channel using this channel + * as the primary or any of the secondary channels isn't possible, + * this includes 80+80 channels + * @NL80211_FREQUENCY_ATTR_NO_160MHZ: any 160 MHz (but not 80+80) channel + * using this channel as the primary or any of the secondary channels + * isn't possible * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number * currently defined * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use @@ -1690,6 +2137,12 @@ enum nl80211_frequency_attr { NL80211_FREQUENCY_ATTR_NO_IBSS, NL80211_FREQUENCY_ATTR_RADAR, NL80211_FREQUENCY_ATTR_MAX_TX_POWER, + NL80211_FREQUENCY_ATTR_DFS_STATE, + NL80211_FREQUENCY_ATTR_DFS_TIME, + NL80211_FREQUENCY_ATTR_NO_HT40_MINUS, + NL80211_FREQUENCY_ATTR_NO_HT40_PLUS, + NL80211_FREQUENCY_ATTR_NO_80MHZ, + NL80211_FREQUENCY_ATTR_NO_160MHZ, /* keep last */ __NL80211_FREQUENCY_ATTR_AFTER_LAST, @@ -1808,6 +2261,8 @@ enum nl80211_reg_rule_attr { * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, * only report BSS with matching SSID. + * @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a + * BSS in scan results. Filtering is turned off if not specified. * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter * attribute number currently defined * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use @@ -1815,7 +2270,8 @@ enum nl80211_reg_rule_attr { enum nl80211_sched_scan_match_attr { __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID, - NL80211_ATTR_SCHED_SCAN_MATCH_SSID, + NL80211_SCHED_SCAN_MATCH_ATTR_SSID, + NL80211_SCHED_SCAN_MATCH_ATTR_RSSI, /* keep last */ __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST, @@ -1823,6 +2279,9 @@ enum nl80211_sched_scan_match_attr { __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1 }; +/* only for backward compatibility */ +#define NL80211_ATTR_SCHED_SCAN_MATCH_SSID NL80211_SCHED_SCAN_MATCH_ATTR_SSID + /** * enum nl80211_reg_rule_flags - regulatory rule flags * @@ -1852,9 +2311,9 @@ enum nl80211_reg_rule_flags { * enum nl80211_dfs_regions - regulatory DFS regions * * @NL80211_DFS_UNSET: Country has no DFS master region specified - * @NL80211_DFS_FCC_: Country follows DFS master rules from FCC - * @NL80211_DFS_FCC_: Country follows DFS master rules from ETSI - * @NL80211_DFS_JP_: Country follows DFS master rules from JP/MKK/Telec + * @NL80211_DFS_FCC: Country follows DFS master rules from FCC + * @NL80211_DFS_ETSI: Country follows DFS master rules from ETSI + * @NL80211_DFS_JP: Country follows DFS master rules from JP/MKK/Telec */ enum nl80211_dfs_regions { NL80211_DFS_UNSET = 0, @@ -1864,6 +2323,26 @@ enum nl80211_dfs_regions { }; /** + * enum nl80211_user_reg_hint_type - type of user regulatory hint + * + * @NL80211_USER_REG_HINT_USER: a user sent the hint. This is always + * assumed if the attribute is not set. + * @NL80211_USER_REG_HINT_CELL_BASE: the hint comes from a cellular + * base station. Device drivers that have been tested to work + * properly to support this type of hint can enable these hints + * by setting the NL80211_FEATURE_CELL_BASE_REG_HINTS feature + * capability on the struct wiphy. The wireless core will + * ignore all cell base station hints until at least one device + * present has been registered with the wireless core that + * has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a + * supported feature. + */ +enum nl80211_user_reg_hint_type { + NL80211_USER_REG_HINT_USER = 0, + NL80211_USER_REG_HINT_CELL_BASE = 1, +}; + +/** * enum nl80211_survey_info - survey information * * These attribute types are used with %NL80211_ATTR_SURVEY_INFO @@ -1934,6 +2413,34 @@ enum nl80211_mntr_flags { }; /** + * enum nl80211_mesh_power_mode - mesh power save modes + * + * @NL80211_MESH_POWER_UNKNOWN: The mesh power mode of the mesh STA is + * not known or has not been set yet. + * @NL80211_MESH_POWER_ACTIVE: Active mesh power mode. The mesh STA is + * in Awake state all the time. + * @NL80211_MESH_POWER_LIGHT_SLEEP: Light sleep mode. The mesh STA will + * alternate between Active and Doze states, but will wake up for + * neighbor's beacons. + * @NL80211_MESH_POWER_DEEP_SLEEP: Deep sleep mode. The mesh STA will + * alternate between Active and Doze states, but may not wake up + * for neighbor's beacons. + * + * @__NL80211_MESH_POWER_AFTER_LAST - internal use + * @NL80211_MESH_POWER_MAX - highest possible power save level + */ + +enum nl80211_mesh_power_mode { + NL80211_MESH_POWER_UNKNOWN, + NL80211_MESH_POWER_ACTIVE, + NL80211_MESH_POWER_LIGHT_SLEEP, + NL80211_MESH_POWER_DEEP_SLEEP, + + __NL80211_MESH_POWER_AFTER_LAST, + NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1 +}; + +/** * enum nl80211_meshconf_params - mesh configuration parameters * * Mesh configuration parameters. These can be changed while the mesh is @@ -1942,62 +2449,98 @@ enum nl80211_mntr_flags { * @__NL80211_MESHCONF_INVALID: internal use * * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in - * millisecond units, used by the Peer Link Open message + * millisecond units, used by the Peer Link Open message * * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in - * millisecond units, used by the peer link management to close a peer link + * millisecond units, used by the peer link management to close a peer link * * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in - * millisecond units + * millisecond units * * @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed - * on this mesh interface + * on this mesh interface * * @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link - * open retries that can be sent to establish a new peer link instance in a - * mesh + * open retries that can be sent to establish a new peer link instance in a + * mesh * * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh - * point. + * point. * - * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically - * open peer links when we detect compatible mesh peers. + * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically open + * peer links when we detect compatible mesh peers. Disabled if + * @NL80211_MESH_SETUP_USERSPACE_MPM or @NL80211_MESH_SETUP_USERSPACE_AMPE are + * set. * * @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames - * containing a PREQ that an MP can send to a particular destination (path - * target) + * containing a PREQ that an MP can send to a particular destination (path + * target) * * @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths - * (in milliseconds) + * (in milliseconds) * * @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait - * until giving up on a path discovery (in milliseconds) + * until giving up on a path discovery (in milliseconds) * * @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh - * points receiving a PREQ shall consider the forwarding information from the - * root to be valid. (TU = time unit) + * points receiving a PREQ shall consider the forwarding information from + * the root to be valid. (TU = time unit) * * @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in - * TUs) during which an MP can send only one action frame containing a PREQ - * reference element + * TUs) during which an MP can send only one action frame containing a PREQ + * reference element * * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs) - * that it takes for an HWMP information element to propagate across the mesh + * that it takes for an HWMP information element to propagate across the + * mesh * * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not * * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a - * source mesh point for path selection elements. + * source mesh point for path selection elements. * * @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between - * root announcements are transmitted. + * root announcements are transmitted. * * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has - * access to a broader network beyond the MBSS. This is done via Root - * Announcement frames. + * access to a broader network beyond the MBSS. This is done via Root + * Announcement frames. + * + * @NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL: The minimum interval of time (in + * TUs) during which a mesh STA can send only one Action frame containing a + * PERR element. + * + * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding + * or forwarding entity (default is TRUE - forwarding entity) + * + * @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the + * threshold for average signal strength of candidate station to establish + * a peer link. + * + * @NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR: maximum number of neighbors + * to synchronize to for 11s default synchronization method + * (see 11C.12.2.2) + * + * @NL80211_MESHCONF_HT_OPMODE: set mesh HT protection mode. * * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute * + * @NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT: The time (in TUs) for + * which mesh STAs receiving a proactive PREQ shall consider the forwarding + * information to the root mesh STA to be valid. + * + * @NL80211_MESHCONF_HWMP_ROOT_INTERVAL: The interval of time (in TUs) between + * proactive PREQs are transmitted. + * + * @NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL: The minimum interval of time + * (in TUs) during which a mesh STA can send only one Action frame + * containing a PREQ element for root path confirmation. + * + * @NL80211_MESHCONF_POWER_MODE: Default mesh power mode for new peer links. + * type &enum nl80211_mesh_power_mode (u32) + * + * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs) + * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { @@ -2019,6 +2562,16 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_ELEMENT_TTL, NL80211_MESHCONF_HWMP_RANN_INTERVAL, NL80211_MESHCONF_GATE_ANNOUNCEMENTS, + NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL, + NL80211_MESHCONF_FORWARDING, + NL80211_MESHCONF_RSSI_THRESHOLD, + NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR, + NL80211_MESHCONF_HT_OPMODE, + NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT, + NL80211_MESHCONF_HWMP_ROOT_INTERVAL, + NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, + NL80211_MESHCONF_POWER_MODE, + NL80211_MESHCONF_AWAKE_WINDOW, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, @@ -2034,30 +2587,40 @@ enum nl80211_meshconf_params { * @__NL80211_MESH_SETUP_INVALID: Internal use * * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a - * vendor specific path selection algorithm or disable it to use the default - * HWMP. + * vendor specific path selection algorithm or disable it to use the + * default HWMP. * * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a - * vendor specific path metric or disable it to use the default Airtime - * metric. + * vendor specific path metric or disable it to use the default Airtime + * metric. * * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a - * robust security network ie, or a vendor specific information element that - * vendors will use to identify the path selection methods and metrics in use. + * robust security network ie, or a vendor specific information element + * that vendors will use to identify the path selection methods and + * metrics in use. * * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication - * daemon will be authenticating mesh candidates. + * daemon will be authenticating mesh candidates. * * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication - * daemon will be securing peer link frames. AMPE is a secured version of Mesh - * Peering Management (MPM) and is implemented with the assistance of a - * userspace daemon. When this flag is set, the kernel will send peer - * management frames to a userspace daemon that will implement AMPE - * functionality (security capabilities selection, key confirmation, and key - * management). When the flag is unset (default), the kernel can autonomously - * complete (unsecured) mesh peering without the need of a userspace daemon. + * daemon will be securing peer link frames. AMPE is a secured version of + * Mesh Peering Management (MPM) and is implemented with the assistance of + * a userspace daemon. When this flag is set, the kernel will send peer + * management frames to a userspace daemon that will implement AMPE + * functionality (security capabilities selection, key confirmation, and + * key management). When the flag is unset (default), the kernel can + * autonomously complete (unsecured) mesh peering without the need of a + * userspace daemon. + * + * @NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC: Enable this option to use a + * vendor specific synchronization method or disable it to use the default + * neighbor offset synchronization + * + * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will + * implement an MPM which handles peer allocation and state. * * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number + * * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use */ enum nl80211_mesh_setup_params { @@ -2067,6 +2630,8 @@ enum nl80211_mesh_setup_params { NL80211_MESH_SETUP_IE, NL80211_MESH_SETUP_USERSPACE_AUTH, NL80211_MESH_SETUP_USERSPACE_AMPE, + NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC, + NL80211_MESH_SETUP_USERSPACE_MPM, /* keep last */ __NL80211_MESH_SETUP_ATTR_AFTER_LAST, @@ -2076,7 +2641,7 @@ enum nl80211_mesh_setup_params { /** * enum nl80211_txq_attr - TX queue parameter attributes * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved - * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*) + * @NL80211_TXQ_ATTR_AC: AC identifier (NL80211_AC_*) * @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning * disabled * @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form @@ -2089,7 +2654,7 @@ enum nl80211_mesh_setup_params { */ enum nl80211_txq_attr { __NL80211_TXQ_ATTR_INVALID, - NL80211_TXQ_ATTR_QUEUE, + NL80211_TXQ_ATTR_AC, NL80211_TXQ_ATTR_TXOP, NL80211_TXQ_ATTR_CWMIN, NL80211_TXQ_ATTR_CWMAX, @@ -2100,13 +2665,30 @@ enum nl80211_txq_attr { NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1 }; -enum nl80211_txq_q { - NL80211_TXQ_Q_VO, - NL80211_TXQ_Q_VI, - NL80211_TXQ_Q_BE, - NL80211_TXQ_Q_BK +enum nl80211_ac { + NL80211_AC_VO, + NL80211_AC_VI, + NL80211_AC_BE, + NL80211_AC_BK, + NL80211_NUM_ACS }; +/* backward compat */ +#define NL80211_TXQ_ATTR_QUEUE NL80211_TXQ_ATTR_AC +#define NL80211_TXQ_Q_VO NL80211_AC_VO +#define NL80211_TXQ_Q_VI NL80211_AC_VI +#define NL80211_TXQ_Q_BE NL80211_AC_BE +#define NL80211_TXQ_Q_BK NL80211_AC_BK + +/** + * enum nl80211_channel_type - channel type + * @NL80211_CHAN_NO_HT: 20 MHz, non-HT channel + * @NL80211_CHAN_HT20: 20 MHz HT channel + * @NL80211_CHAN_HT40MINUS: HT40 channel, secondary channel + * below the control channel + * @NL80211_CHAN_HT40PLUS: HT40 channel, secondary channel + * above the control channel + */ enum nl80211_channel_type { NL80211_CHAN_NO_HT, NL80211_CHAN_HT20, @@ -2115,6 +2697,32 @@ enum nl80211_channel_type { }; /** + * enum nl80211_chan_width - channel width definitions + * + * These values are used with the %NL80211_ATTR_CHANNEL_WIDTH + * attribute. + * + * @NL80211_CHAN_WIDTH_20_NOHT: 20 MHz, non-HT channel + * @NL80211_CHAN_WIDTH_20: 20 MHz HT channel + * @NL80211_CHAN_WIDTH_40: 40 MHz channel, the %NL80211_ATTR_CENTER_FREQ1 + * attribute must be provided as well + * @NL80211_CHAN_WIDTH_80: 80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1 + * attribute must be provided as well + * @NL80211_CHAN_WIDTH_80P80: 80+80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1 + * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well + * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1 + * attribute must be provided as well + */ +enum nl80211_chan_width { + NL80211_CHAN_WIDTH_20_NOHT, + NL80211_CHAN_WIDTH_20, + NL80211_CHAN_WIDTH_40, + NL80211_CHAN_WIDTH_80, + NL80211_CHAN_WIDTH_80P80, + NL80211_CHAN_WIDTH_160, +}; + +/** * enum nl80211_bss - netlink attributes for a BSS * * @__NL80211_BSS_INVALID: invalid @@ -2182,6 +2790,7 @@ enum nl80211_bss_status { * @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only) * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r) * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP) + * @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals * @__NL80211_AUTHTYPE_NUM: internal * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by @@ -2193,6 +2802,7 @@ enum nl80211_auth_type { NL80211_AUTHTYPE_SHARED_KEY, NL80211_AUTHTYPE_FT, NL80211_AUTHTYPE_NETWORK_EAP, + NL80211_AUTHTYPE_SAE, /* keep last */ __NL80211_AUTHTYPE_NUM, @@ -2292,12 +2902,15 @@ enum nl80211_key_attributes { * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with * 1 = 500 kbps) but without the IE length restriction (at most * %NL80211_MAX_SUPP_RATES in a single array). + * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection + * in an array of MCS numbers. * @__NL80211_TXRATE_AFTER_LAST: internal * @NL80211_TXRATE_MAX: highest TX rate attribute */ enum nl80211_tx_rate_attributes { __NL80211_TXRATE_INVALID, NL80211_TXRATE_LEGACY, + NL80211_TXRATE_MCS, /* keep last */ __NL80211_TXRATE_AFTER_LAST, @@ -2308,12 +2921,19 @@ enum nl80211_tx_rate_attributes { * enum nl80211_band - Frequency band * @NL80211_BAND_2GHZ: 2.4 GHz ISM band * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz) + * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 64.80 GHz) */ enum nl80211_band { NL80211_BAND_2GHZ, NL80211_BAND_5GHZ, + NL80211_BAND_60GHZ, }; +/** + * enum nl80211_ps_state - powersave state + * @NL80211_PS_DISABLED: powersave is disabled + * @NL80211_PS_ENABLED: powersave is enabled + */ enum nl80211_ps_state { NL80211_PS_DISABLED, NL80211_PS_ENABLED, @@ -2331,6 +2951,17 @@ enum nl80211_ps_state { * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many * consecutive packets were not acknowledged by the peer + * @NL80211_ATTR_CQM_TXE_RATE: TX error rate in %. Minimum % of TX failures + * during the given %NL80211_ATTR_CQM_TXE_INTVL before an + * %NL80211_CMD_NOTIFY_CQM with reported %NL80211_ATTR_CQM_TXE_RATE and + * %NL80211_ATTR_CQM_TXE_PKTS is generated. + * @NL80211_ATTR_CQM_TXE_PKTS: number of attempted packets in a given + * %NL80211_ATTR_CQM_TXE_INTVL before %NL80211_ATTR_CQM_TXE_RATE is + * checked. + * @NL80211_ATTR_CQM_TXE_INTVL: interval in seconds. Specifies the periodic + * interval in which %NL80211_ATTR_CQM_TXE_PKTS and + * %NL80211_ATTR_CQM_TXE_RATE must be satisfied before generating an + * %NL80211_CMD_NOTIFY_CQM. Set to 0 to turn off TX error reporting. * @__NL80211_ATTR_CQM_AFTER_LAST: internal * @NL80211_ATTR_CQM_MAX: highest key attribute */ @@ -2340,6 +2971,9 @@ enum nl80211_attr_cqm { NL80211_ATTR_CQM_RSSI_HYST, NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT, NL80211_ATTR_CQM_PKT_LOSS_EVENT, + NL80211_ATTR_CQM_TXE_RATE, + NL80211_ATTR_CQM_TXE_PKTS, + NL80211_ATTR_CQM_TXE_INTVL, /* keep last */ __NL80211_ATTR_CQM_AFTER_LAST, @@ -2352,10 +2986,14 @@ enum nl80211_attr_cqm { * configured threshold * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the * configured threshold + * @NL80211_CQM_RSSI_BEACON_LOSS_EVENT: The device experienced beacon loss. + * (Note that deauth/disassoc will still follow if the AP is not + * available. This event might get used as roaming event, etc.) */ enum nl80211_cqm_rssi_threshold_event { NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW, NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH, + NL80211_CQM_RSSI_BEACON_LOSS_EVENT, }; @@ -2383,10 +3021,12 @@ enum nl80211_tx_power_setting { * corresponds to the lowest-order bit in the second byte of the mask. * For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where * xx indicates "don't care") would be represented by a pattern of - * twelve zero bytes, and a mask of "0xed,0x07". + * twelve zero bytes, and a mask of "0xed,0x01". * Note that the pattern matching is done as though frames were not * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked * first (including SNAP header unpacking) and then matched. + * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after + * these fixed number of bytes of received packet * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number */ @@ -2394,6 +3034,7 @@ enum nl80211_wowlan_packet_pattern_attr { __NL80211_WOWLAN_PKTPAT_INVALID, NL80211_WOWLAN_PKTPAT_MASK, NL80211_WOWLAN_PKTPAT_PATTERN, + NL80211_WOWLAN_PKTPAT_OFFSET, NUM_NL80211_WOWLAN_PKTPAT, MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, @@ -2404,6 +3045,7 @@ enum nl80211_wowlan_packet_pattern_attr { * @max_patterns: maximum number of patterns supported * @min_pattern_len: minimum length of each pattern * @max_pattern_len: maximum length of each pattern + * @max_pkt_offset: maximum Rx packet offset * * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the @@ -2413,6 +3055,7 @@ struct nl80211_wowlan_pattern_support { __u32 max_patterns; __u32 min_pattern_len; __u32 max_pattern_len; + __u32 max_pkt_offset; } __attribute__((packed)); /** @@ -2428,12 +3071,17 @@ struct nl80211_wowlan_pattern_support { * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns * which are passed in an array of nested attributes, each nested attribute * defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern. - * Each pattern defines a wakeup packet. The matching is done on the MSDU, - * i.e. as though the packet was an 802.3 packet, so the pattern matching - * is done after the packet is converted to the MSDU. + * Each pattern defines a wakeup packet. Packet offset is associated with + * each pattern which is used while matching the pattern. The matching is + * done on the MSDU, i.e. as though the packet was an 802.3 packet, so the + * pattern matching is done after the packet is converted to the MSDU. * * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute * carrying a &struct nl80211_wowlan_pattern_support. + * + * When reporting wakeup. it is a u32 attribute containing the 0-based + * index of the pattern that caused the wakeup, in the patterns passed + * to the kernel when configuring. * @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be * used when setting, used only to indicate that GTK rekeying is supported * by the device (flag) @@ -2444,8 +3092,36 @@ struct nl80211_wowlan_pattern_support { * @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag) * @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released * (on devices that have rfkill in the device) (flag) + * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211: For wakeup reporting only, contains + * the 802.11 packet that caused the wakeup, e.g. a deauth frame. The frame + * may be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN + * attribute contains the original length. + * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN: Original length of the 802.11 + * packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211 + * attribute if the packet was truncated somewhere. + * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023: For wakeup reporting only, contains the + * 802.11 packet that caused the wakeup, e.g. a magic packet. The frame may + * be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN attribute + * contains the original length. + * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN: Original length of the 802.3 + * packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023 + * attribute if the packet was truncated somewhere. + * @NL80211_WOWLAN_TRIG_TCP_CONNECTION: TCP connection wake, see DOC section + * "TCP connection wakeup" for more details. This is a nested attribute + * containing the exact information for establishing and keeping alive + * the TCP connection. + * @NL80211_WOWLAN_TRIG_TCP_WAKEUP_MATCH: For wakeup reporting only, the + * wakeup packet was received on the TCP connection + * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST: For wakeup reporting only, the + * TCP connection was lost or failed to be established + * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS: For wakeup reporting only, + * the TCP connection ran out of tokens to use for data to send to the + * service * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number + * + * These nested attributes are used to configure the wakeup triggers and + * to report the wakeup reason(s). */ enum nl80211_wowlan_triggers { __NL80211_WOWLAN_TRIG_INVALID, @@ -2458,6 +3134,14 @@ enum nl80211_wowlan_triggers { NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST, NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE, NL80211_WOWLAN_TRIG_RFKILL_RELEASE, + NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211, + NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN, + NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023, + NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN, + NL80211_WOWLAN_TRIG_TCP_CONNECTION, + NL80211_WOWLAN_TRIG_WAKEUP_TCP_MATCH, + NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST, + NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS, /* keep last */ NUM_NL80211_WOWLAN_TRIG, @@ -2465,6 +3149,116 @@ enum nl80211_wowlan_triggers { }; /** + * DOC: TCP connection wakeup + * + * Some devices can establish a TCP connection in order to be woken up by a + * packet coming in from outside their network segment, or behind NAT. If + * configured, the device will establish a TCP connection to the given + * service, and periodically send data to that service. The first data + * packet is usually transmitted after SYN/ACK, also ACKing the SYN/ACK. + * The data packets can optionally include a (little endian) sequence + * number (in the TCP payload!) that is generated by the device, and, also + * optionally, a token from a list of tokens. This serves as a keep-alive + * with the service, and for NATed connections, etc. + * + * During this keep-alive period, the server doesn't send any data to the + * client. When receiving data, it is compared against the wakeup pattern + * (and mask) and if it matches, the host is woken up. Similarly, if the + * connection breaks or cannot be established to start with, the host is + * also woken up. + * + * Developer's note: ARP offload is required for this, otherwise TCP + * response packets might not go through correctly. + */ + +/** + * struct nl80211_wowlan_tcp_data_seq - WoWLAN TCP data sequence + * @start: starting value + * @offset: offset of sequence number in packet + * @len: length of the sequence value to write, 1 through 4 + * + * Note: don't confuse with the TCP sequence number(s), this is for the + * keepalive packet payload. The actual value is written into the packet + * in little endian. + */ +struct nl80211_wowlan_tcp_data_seq { + __u32 start, offset, len; +}; + +/** + * struct nl80211_wowlan_tcp_data_token - WoWLAN TCP data token config + * @offset: offset of token in packet + * @len: length of each token + * @token_stream: stream of data to be used for the tokens, the length must + * be a multiple of @len for this to make sense + */ +struct nl80211_wowlan_tcp_data_token { + __u32 offset, len; + __u8 token_stream[]; +}; + +/** + * struct nl80211_wowlan_tcp_data_token_feature - data token features + * @min_len: minimum token length + * @max_len: maximum token length + * @bufsize: total available token buffer size (max size of @token_stream) + */ +struct nl80211_wowlan_tcp_data_token_feature { + __u32 min_len, max_len, bufsize; +}; + +/** + * enum nl80211_wowlan_tcp_attrs - WoWLAN TCP connection parameters + * @__NL80211_WOWLAN_TCP_INVALID: invalid number for nested attributes + * @NL80211_WOWLAN_TCP_SRC_IPV4: source IPv4 address (in network byte order) + * @NL80211_WOWLAN_TCP_DST_IPV4: destination IPv4 address + * (in network byte order) + * @NL80211_WOWLAN_TCP_DST_MAC: destination MAC address, this is given because + * route lookup when configured might be invalid by the time we suspend, + * and doing a route lookup when suspending is no longer possible as it + * might require ARP querying. + * @NL80211_WOWLAN_TCP_SRC_PORT: source port (u16); optional, if not given a + * socket and port will be allocated + * @NL80211_WOWLAN_TCP_DST_PORT: destination port (u16) + * @NL80211_WOWLAN_TCP_DATA_PAYLOAD: data packet payload, at least one byte. + * For feature advertising, a u32 attribute holding the maximum length + * of the data payload. + * @NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ: data packet sequence configuration + * (if desired), a &struct nl80211_wowlan_tcp_data_seq. For feature + * advertising it is just a flag + * @NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN: data packet token configuration, + * see &struct nl80211_wowlan_tcp_data_token and for advertising see + * &struct nl80211_wowlan_tcp_data_token_feature. + * @NL80211_WOWLAN_TCP_DATA_INTERVAL: data interval in seconds, maximum + * interval in feature advertising (u32) + * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a + * u32 attribute holding the maximum length + * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for + * feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK + * but on the TCP payload only. + * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes + * @MAX_NL80211_WOWLAN_TCP: highest attribute number + */ +enum nl80211_wowlan_tcp_attrs { + __NL80211_WOWLAN_TCP_INVALID, + NL80211_WOWLAN_TCP_SRC_IPV4, + NL80211_WOWLAN_TCP_DST_IPV4, + NL80211_WOWLAN_TCP_DST_MAC, + NL80211_WOWLAN_TCP_SRC_PORT, + NL80211_WOWLAN_TCP_DST_PORT, + NL80211_WOWLAN_TCP_DATA_PAYLOAD, + NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ, + NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN, + NL80211_WOWLAN_TCP_DATA_INTERVAL, + NL80211_WOWLAN_TCP_WAKE_PAYLOAD, + NL80211_WOWLAN_TCP_WAKE_MASK, + + /* keep last */ + NUM_NL80211_WOWLAN_TCP, + MAX_NL80211_WOWLAN_TCP = NUM_NL80211_WOWLAN_TCP - 1 +}; + +/** * enum nl80211_iface_limit_attrs - limit attributes * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that @@ -2500,6 +3294,8 @@ enum nl80211_iface_limit_attrs { * the infrastructure network's beacon interval. * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many * different channels may be used within this group. + * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap + * of supported channel widths for radar detection. * @NUM_NL80211_IFACE_COMB: number of attributes * @MAX_NL80211_IFACE_COMB: highest attribute number * @@ -2532,6 +3328,7 @@ enum nl80211_if_combination_attrs { NL80211_IFACE_COMB_MAXNUM, NL80211_IFACE_COMB_STA_AP_BI_MATCH, NL80211_IFACE_COMB_NUM_CHANNELS, + NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS, /* keep last */ NUM_NL80211_IFACE_COMB, @@ -2571,6 +3368,23 @@ enum nl80211_plink_state { MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1 }; +/** + * enum nl80211_plink_action - actions to perform in mesh peers + * + * @NL80211_PLINK_ACTION_NO_ACTION: perform no action + * @NL80211_PLINK_ACTION_OPEN: start mesh peer link establishment + * @NL80211_PLINK_ACTION_BLOCK: block traffic from this mesh peer + * @NUM_NL80211_PLINK_ACTIONS: number of possible actions + */ +enum plink_actions { + NL80211_PLINK_ACTION_NO_ACTION, + NL80211_PLINK_ACTION_OPEN, + NL80211_PLINK_ACTION_BLOCK, + + NUM_NL80211_PLINK_ACTIONS, +}; + + #define NL80211_KCK_LEN 16 #define NL80211_KEK_LEN 16 #define NL80211_REPLAY_CTR_LEN 8 @@ -2669,4 +3483,203 @@ enum nl80211_tdls_operation { NL80211_TDLS_DISABLE_LINK, }; +/* + * enum nl80211_ap_sme_features - device-integrated AP features + * Reserved for future use, no bits are defined in + * NL80211_ATTR_DEVICE_AP_SME yet. +enum nl80211_ap_sme_features { +}; + */ + +/** + * enum nl80211_feature_flags - device/driver features + * @NL80211_FEATURE_SK_TX_STATUS: This driver supports reflecting back + * TX status to the socket error queue when requested with the + * socket option. + * @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates. + * @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up + * the connected inactive stations in AP mode. + * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested + * to work properly to suppport receiving regulatory hints from + * cellular base stations. + * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: If this is set, an active + * P2P Device (%NL80211_IFTYPE_P2P_DEVICE) requires its own channel + * in the interface combinations, even when it's only used for scan + * and remain-on-channel. This could be due to, for example, the + * remain-on-channel implementation requiring a channel context. + * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of + * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station + * mode + * @NL80211_FEATURE_LOW_PRIORITY_SCAN: This driver supports low priority scan + * @NL80211_FEATURE_SCAN_FLUSH: Scan flush is supported + * @NL80211_FEATURE_AP_SCAN: Support scanning using an AP vif + * @NL80211_FEATURE_VIF_TXPOWER: The driver supports per-vif TX power setting + * @NL80211_FEATURE_NEED_OBSS_SCAN: The driver expects userspace to perform + * OBSS scans and generate 20/40 BSS coex reports. This flag is used only + * for drivers implementing the CONNECT API, for AUTH/ASSOC it is implied. + * @NL80211_FEATURE_P2P_GO_CTWIN: P2P GO implementation supports CT Window + * setting + * @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic + * powersave + * @NL80211_FEATURE_FULL_AP_CLIENT_STATE: The driver supports full state + * transitions for AP clients. Without this flag (and if the driver + * doesn't have the AP SME in the device) the driver supports adding + * stations only when they're associated and adds them in associated + * state (to later be transitioned into authorized), with this flag + * they should be added before even sending the authentication reply + * and then transitioned into authenticated, associated and authorized + * states using station flags. + * Note that even for drivers that support this, the default is to add + * stations in authenticated/associated state, so to add unauthenticated + * stations the authenticated/associated bits have to be set in the mask. + * @NL80211_FEATURE_ADVERTISE_CHAN_LIMITS: cfg80211 advertises channel limits + * (HT40, VHT 80/160 MHz) if this flag is set + * @NL80211_FEATURE_USERSPACE_MPM: This driver supports a userspace Mesh + * Peering Management entity which may be implemented by registering for + * beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is + * still generated by the driver. + */ +enum nl80211_feature_flags { + NL80211_FEATURE_SK_TX_STATUS = 1 << 0, + NL80211_FEATURE_HT_IBSS = 1 << 1, + NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2, + NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3, + NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4, + NL80211_FEATURE_SAE = 1 << 5, + NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6, + NL80211_FEATURE_SCAN_FLUSH = 1 << 7, + NL80211_FEATURE_AP_SCAN = 1 << 8, + NL80211_FEATURE_VIF_TXPOWER = 1 << 9, + NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10, + NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11, + NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12, + /* bit 13 is reserved */ + NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14, + NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15, + NL80211_FEATURE_USERSPACE_MPM = 1 << 16, +}; + +/** + * enum nl80211_probe_resp_offload_support_attr - optional supported + * protocols for probe-response offloading by the driver/FW. + * To be used with the %NL80211_ATTR_PROBE_RESP_OFFLOAD attribute. + * Each enum value represents a bit in the bitmap of supported + * protocols. Typically a subset of probe-requests belonging to a + * supported protocol will be excluded from offload and uploaded + * to the host. + * + * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS: Support for WPS ver. 1 + * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2: Support for WPS ver. 2 + * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P: Support for P2P + * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U: Support for 802.11u + */ +enum nl80211_probe_resp_offload_support_attr { + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS = 1<<0, + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 = 1<<1, + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P = 1<<2, + NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U = 1<<3, +}; + +/** + * enum nl80211_connect_failed_reason - connection request failed reasons + * @NL80211_CONN_FAIL_MAX_CLIENTS: Maximum number of clients that can be + * handled by the AP is reached. + * @NL80211_CONN_FAIL_BLOCKED_CLIENT: Connection request is rejected due to ACL. + */ +enum nl80211_connect_failed_reason { + NL80211_CONN_FAIL_MAX_CLIENTS, + NL80211_CONN_FAIL_BLOCKED_CLIENT, +}; + +/** + * enum nl80211_scan_flags - scan request control flags + * + * Scan request control flags are used to control the handling + * of NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_START_SCHED_SCAN + * requests. + * + * @NL80211_SCAN_FLAG_LOW_PRIORITY: scan request has low priority + * @NL80211_SCAN_FLAG_FLUSH: flush cache before scanning + * @NL80211_SCAN_FLAG_AP: force a scan even if the interface is configured + * as AP and the beaconing has already been configured. This attribute is + * dangerous because will destroy stations performance as a lot of frames + * will be lost while scanning off-channel, therefore it must be used only + * when really needed + */ +enum nl80211_scan_flags { + NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0, + NL80211_SCAN_FLAG_FLUSH = 1<<1, + NL80211_SCAN_FLAG_AP = 1<<2, +}; + +/** + * enum nl80211_acl_policy - access control policy + * + * Access control policy is applied on a MAC list set by + * %NL80211_CMD_START_AP and %NL80211_CMD_SET_MAC_ACL, to + * be used with %NL80211_ATTR_ACL_POLICY. + * + * @NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED: Deny stations which are + * listed in ACL, i.e. allow all the stations which are not listed + * in ACL to authenticate. + * @NL80211_ACL_POLICY_DENY_UNLESS_LISTED: Allow the stations which are listed + * in ACL, i.e. deny all the stations which are not listed in ACL. + */ +enum nl80211_acl_policy { + NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED, + NL80211_ACL_POLICY_DENY_UNLESS_LISTED, +}; + +/** + * enum nl80211_radar_event - type of radar event for DFS operation + * + * Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace + * about detected radars or success of the channel available check (CAC) + * + * @NL80211_RADAR_DETECTED: A radar pattern has been detected. The channel is + * now unusable. + * @NL80211_RADAR_CAC_FINISHED: Channel Availability Check has been finished, + * the channel is now available. + * @NL80211_RADAR_CAC_ABORTED: Channel Availability Check has been aborted, no + * change to the channel status. + * @NL80211_RADAR_NOP_FINISHED: The Non-Occupancy Period for this channel is + * over, channel becomes usable. + */ +enum nl80211_radar_event { + NL80211_RADAR_DETECTED, + NL80211_RADAR_CAC_FINISHED, + NL80211_RADAR_CAC_ABORTED, + NL80211_RADAR_NOP_FINISHED, +}; + +/** + * enum nl80211_dfs_state - DFS states for channels + * + * Channel states used by the DFS code. + * + * @IEEE80211_DFS_USABLE: The channel can be used, but channel availability + * check (CAC) must be performed before using it for AP or IBSS. + * @IEEE80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it + * is therefore marked as not available. + * @IEEE80211_DFS_AVAILABLE: The channel has been CAC checked and is available. + */ + +enum nl80211_dfs_state { + NL80211_DFS_USABLE, + NL80211_DFS_UNAVAILABLE, + NL80211_DFS_AVAILABLE, +}; + +/** + * enum enum nl80211_protocol_features - nl80211 protocol features + * @NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP: nl80211 supports splitting + * wiphy dumps (if requested by the application with the attribute + * %NL80211_ATTR_SPLIT_WIPHY_DUMP. Also supported is filtering the + * wiphy dump by %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFINDEX or + * %NL80211_ATTR_WDEV. + */ +enum nl80211_protocol_features { + NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP = 1 << 0, +}; + #endif /* __LINUX_NL80211_H */ -- 1.7.4.1 -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
