On 03/08/2013 03:23 PM, Jenya Y wrote:
On 03/08/2013 10:02 PM, Larry Finger wrote:
No, it was not. At the end were the lines
[ 19.322729] rtl8187: wireless switch is on
[ 19.322763] usbcore: registered new interface driver rtl8187
[ 19.423269] systemd-udevd[272]: renamed network interface wlan0 to
wlp0s29f7u7u3
[ 21.321746] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u7u3: link is not ready
Why are your udev rules renaming wlan0 to that crazy string?
Your ESSID for the AP of "1.618029" is also strange, but that works OK here.
Note that I added the ML to this reply.
Larry
The ID didn't cause any issues before, neither did the strange names (courtesy
of systemd 197) and they are indeed very strange but as you have already seen
the same setup is working in 3.8.2
Here are relevant dmesg output in 3.8.2 //
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.2-1-jy (jy@Y8) (gcc version 4.7.2 (GCC) ) #1
SMP PREEMPT Thu Mar 7 23:37:49 CET 2013
....
[ 17.868726] cfg80211: Calling CRDA to update world regulatory domain
[ 17.991571] cfg80211: World regulatory domain updated:
[ 17.991574] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 17.991576] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 17.991578] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 17.991580] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 17.991582] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 17.991583] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 18.393371] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.393650] ieee80211 phy0: hwaddr 00:15:af:03:b1:88, RTL8187vB (default) V1
+ rtl8225z2, rfkill mask 2
[ 18.404459] rtl8187: Customer ID is 0x00
[ 18.404944] rtl8187: wireless switch is on
[ 18.404970] usbcore: registered new interface driver rtl8187
[ 18.518265] systemd-udevd[326]: renamed network interface wlan0 to wlp0s29f7u7u3
[ 20.419743] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u7u3: link is not ready
[ 30.480518] wlp0s29f7u7u3: authenticate with 00:13:49:df:22:72
[ 30.515723] wlp0s29f7u7u3: capabilities/regulatory prevented using AP HT/VHT
configuration, downgraded
[ 30.552709] wlp0s29f7u7u3: send auth to 00:13:49:df:22:72 (try 1/3)
[ 30.554577] wlp0s29f7u7u3: authenticated
[ 30.554666] rtl8187 5-7.3:1.0 wlp0s29f7u7u3: disabling HT as WMM/QoS is not
supported by the AP
[ 30.554669] rtl8187 5-7.3:1.0 wlp0s29f7u7u3: disabling VHT as WMM/QoS is not
supported by the AP
[ 30.555028] wlp0s29f7u7u3: associate with 00:13:49:df:22:72 (try 1/3)
[ 30.557461] wlp0s29f7u7u3: RX AssocResp from 00:13:49:df:22:72 (capab=0x411
status=0 aid=1)
[ 30.558206] wlp0s29f7u7u3: associated
[ 30.558237] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u7u3: link becomes ready
so is there maybe a quick fix?
I have another idea, I should try out. Maybe I should try to disable IPv6 in my
network settings.
I see that had no effect. You need to bisect between HEAD and v3.8.
Larry
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
