This adds some code to init the 2055 radio.
This patch adds two files "tables_nphy.h" and "tables_nphy.c"
Signed-off-by: Michael Buesch <mb@xxxxxxxxx>
---
For 2.6.25.
Index: wireless-2.6/drivers/net/wireless/b43/nphy.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/nphy.c 2008-01-13 20:57:36.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/nphy.c 2008-01-13 21:05:54.000000000 +0100
@@ -21,14 +21,110 @@
Boston, MA 02110-1301, USA.
*/
#include "b43.h"
#include "nphy.h"
+#include "tables_nphy.h"
+void b43_nphy_set_rxantenna(struct b43_wldev *dev, int antenna)
+{//TODO
+}
+
+void b43_nphy_xmitpower(struct b43_wldev *dev)
+{//TODO
+}
+
+/* Tune the hardware to a new channel. Don't call this directly.
+ * Use b43_radio_selectchannel() */
+void b43_nphy_selectchannel(struct b43_wldev *dev, u8 channel)
+{
+
+//TODO
+}
+
+static void b43_radio_init2055_pre(struct b43_wldev *dev)
+{
+ b43_phy_mask(dev, B43_NPHY_RFCTL_CMD,
+ ~B43_NPHY_RFCTL_CMD_PORFORCE);
+ b43_phy_set(dev, B43_NPHY_RFCTL_CMD,
+ B43_NPHY_RFCTL_CMD_CHIP0PU |
+ B43_NPHY_RFCTL_CMD_OEPORFORCE);
+ b43_phy_set(dev, B43_NPHY_RFCTL_CMD,
+ B43_NPHY_RFCTL_CMD_PORFORCE);
+}
+
+static void b43_radio_init2055_post(struct b43_wldev *dev)
+{
+ struct ssb_sprom *sprom = &(dev->dev->bus->sprom);
+ struct ssb_boardinfo *binfo = &(dev->dev->bus->boardinfo);
+ int i;
+ u16 val;
+
+ b43_radio_mask(dev, B2055_MASTER1, 0xFFF3);
+ msleep(1);
+ if ((sprom->revision != 4) || !(sprom->boardflags_hi & 0x0002)) {
+ if ((binfo->vendor != PCI_VENDOR_ID_BROADCOM) ||
+ (binfo->type != 0x46D) ||
+ (binfo->rev < 0x41)) {
+ b43_radio_mask(dev, B2055_C1_RX_BB_REG, 0x7F);
+ b43_radio_mask(dev, B2055_C1_RX_BB_REG, 0x7F);
+ msleep(1);
+ }
+ }
+ b43_radio_maskset(dev, B2055_RRCCAL_NOPTSEL, 0x3F, 0x2C);
+ msleep(1);
+ b43_radio_write16(dev, B2055_CAL_MISC, 0x3C);
+ msleep(1);
+ b43_radio_mask(dev, B2055_CAL_MISC, 0xFFBE);
+ msleep(1);
+ b43_radio_set(dev, B2055_CAL_LPOCTL, 0x80);
+ msleep(1);
+ b43_radio_set(dev, B2055_CAL_MISC, 0x1);
+ msleep(1);
+ b43_radio_set(dev, B2055_CAL_MISC, 0x40);
+ msleep(1);
+ for (i = 0; i < 100; i++) {
+ val = b43_radio_read16(dev, B2055_CAL_COUT2);
+ if (val & 0x80)
+ break;
+ udelay(10);
+ }
+ msleep(1);
+ b43_radio_mask(dev, B2055_CAL_LPOCTL, 0xFF7F);
+ msleep(1);
+ b43_radio_selectchannel(dev, dev->phy.channel, 0);
+ b43_radio_write16(dev, B2055_C1_RX_BB_LPF, 0x9);
+ b43_radio_write16(dev, B2055_C2_RX_BB_LPF, 0x9);
+ b43_radio_write16(dev, B2055_C1_RX_BB_MIDACHP, 0x83);
+ b43_radio_write16(dev, B2055_C2_RX_BB_MIDACHP, 0x83);
+}
+
+/* Initialize a Broadcom 2055 N-radio */
+static void b43_radio_init2055(struct b43_wldev *dev)
+{
+ b43_radio_init2055_pre(dev);
+ if (b43_status(dev) < B43_STAT_INITIALIZED)
+ b2055_upload_inittab(dev, 0, 1);
+ else
+ b2055_upload_inittab(dev, 0/*FIXME on 5ghz band*/, 0);
+ b43_radio_init2055_post(dev);
+}
+
+void b43_nphy_radio_turn_on(struct b43_wldev *dev)
+{
+ b43_radio_init2055(dev);
+}
+
+void b43_nphy_radio_turn_off(struct b43_wldev *dev)
+{
+ b43_phy_mask(dev, B43_NPHY_RFCTL_CMD,
+ ~B43_NPHY_RFCTL_CMD_EN);
+}
+
int b43_phy_initn(struct b43_wldev *dev)
{
b43err(dev->wl, "IEEE 802.11n devices are not supported, yet.\n");
- return -EOPNOTSUPP;
+ return 0;
}
Index: wireless-2.6/drivers/net/wireless/b43/nphy.h
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/nphy.h 2008-01-13 20:57:36.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/nphy.h 2008-01-13 21:02:46.000000000 +0100
@@ -174,12 +174,13 @@
#define B43_NPHY_RFCTL_CMD_CORESEL_SHIFT 3
#define B43_NPHY_RFCTL_CMD_PORFORCE 0x0040 /* POR force */
#define B43_NPHY_RFCTL_CMD_OEPORFORCE 0x0080 /* OE POR force */
#define B43_NPHY_RFCTL_CMD_RXEN 0x0100 /* RX enable */
#define B43_NPHY_RFCTL_CMD_TXEN 0x0200 /* TX enable */
#define B43_NPHY_RFCTL_CMD_CHIP0PU 0x0400 /* Chip0 PU */
+#define B43_NPHY_RFCTL_CMD_EN 0x0800 /* Radio enabled */
#define B43_NPHY_RFCTL_CMD_SEQENCORE 0xF000 /* Seq en core */
#define B43_NPHY_RFCTL_CMD_SEQENCORE_SHIFT 12
#define B43_NPHY_RFCTL_RSSIO1 B43_PHY_N(0x07A) /* RF control (RSSI others 1) */
#define B43_NPHY_RFCTL_RSSIO1_RXPD 0x0001 /* RX PD */
#define B43_NPHY_RFCTL_RSSIO1_TXPD 0x0002 /* TX PD */
#define B43_NPHY_RFCTL_RSSIO1_PAPD 0x0004 /* PA PD */
@@ -910,7 +911,15 @@
struct b43_wldev;
int b43_phy_initn(struct b43_wldev *dev);
+void b43_nphy_radio_turn_on(struct b43_wldev *dev);
+void b43_nphy_radio_turn_off(struct b43_wldev *dev);
+
+void b43_nphy_selectchannel(struct b43_wldev *dev, u8 channel);
+
+void b43_nphy_xmitpower(struct b43_wldev *dev);
+void b43_nphy_set_rxantenna(struct b43_wldev *dev, int antenna);
+
#endif /* B43_NPHY_H_ */
Index: wireless-2.6/drivers/net/wireless/b43/phy.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/phy.c 2008-01-13 20:57:36.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/phy.c 2008-01-13 21:02:46.000000000 +0100
@@ -305,12 +305,30 @@ void b43_phy_write(struct b43_wldev *dev
offset = adjust_phyreg_for_phytype(phy, offset, dev);
b43_write16(dev, B43_MMIO_PHY_CONTROL, offset);
b43_write16(dev, B43_MMIO_PHY_DATA, val);
}
+void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask)
+{
+ b43_phy_write(dev, offset,
+ b43_phy_read(dev, offset) & mask);
+}
+
+void b43_phy_set(struct b43_wldev *dev, u16 offset, u16 set)
+{
+ b43_phy_write(dev, offset,
+ b43_phy_read(dev, offset) | set);
+}
+
+void b43_phy_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set)
+{
+ b43_phy_write(dev, offset,
+ (b43_phy_read(dev, offset) & mask) | set);
+}
+
/* Adjust the transmission power output (G-PHY) */
void b43_set_txpower_g(struct b43_wldev *dev,
const struct b43_bbatt *bbatt,
const struct b43_rfatt *rfatt, u8 tx_control)
{
struct b43_phy *phy = &dev->phy;
@@ -1854,12 +1872,15 @@ void b43_phy_xmitpower(struct b43_wldev
phy->tx_control);
b43_lo_g_ctl_mark_cur_used(dev);
b43_radio_unlock(dev);
b43_phy_unlock(dev);
break;
}
+ case B43_PHYTYPE_N:
+ b43_nphy_xmitpower(dev);
+ break;
default:
B43_WARN_ON(1);
}
}
static inline s32 b43_tssi2dbm_ad(s32 num, s32 den)
@@ -2113,12 +2134,15 @@ void b43_set_rx_antenna(struct b43_wldev
tmp = b43_phy_read(dev, B43_PHY_CCKBBANDCFG);
tmp &= ~B43_PHY_BBANDCFG_RXANT;
tmp |= (autodiv ? B43_ANTENNA_AUTO0 : antenna)
<< B43_PHY_BBANDCFG_RXANT_SHIFT;
b43_phy_write(dev, B43_PHY_CCKBBANDCFG, tmp);
break;
+ case B43_PHYTYPE_N:
+ b43_nphy_set_rxantenna(dev, antenna);
+ break;
default:
B43_WARN_ON(1);
}
hf |= B43_HF_ANTDIVHELP;
b43_hf_write(dev, hf);
@@ -2212,12 +2236,30 @@ void b43_radio_write16(struct b43_wldev
B43_WARN_ON(offset == 1);
b43_write16(dev, B43_MMIO_RADIO_CONTROL, offset);
b43_write16(dev, B43_MMIO_RADIO_DATA_LOW, val);
}
+void b43_radio_mask(struct b43_wldev *dev, u16 offset, u16 mask)
+{
+ b43_radio_write16(dev, offset,
+ b43_radio_read16(dev, offset) & mask);
+}
+
+void b43_radio_set(struct b43_wldev *dev, u16 offset, u16 set)
+{
+ b43_radio_write16(dev, offset,
+ b43_radio_read16(dev, offset) | set);
+}
+
+void b43_radio_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set)
+{
+ b43_radio_write16(dev, offset,
+ (b43_radio_read16(dev, offset) & mask) | set);
+}
+
static void b43_set_all_gains(struct b43_wldev *dev,
s16 first, s16 second, s16 third)
{
struct b43_phy *phy = &dev->phy;
u16 i;
u16 start = 0x08, end = 0x18;
@@ -3849,26 +3891,32 @@ int b43_radio_selectchannel(struct b43_w
channel = B43_DEFAULT_CHANNEL_A;
break;
case B43_PHYTYPE_B:
case B43_PHYTYPE_G:
channel = B43_DEFAULT_CHANNEL_BG;
break;
+ case B43_PHYTYPE_N:
+ //FIXME check if we are on 2.4GHz or 5GHz and set a default channel.
+ channel = 1;
+ break;
default:
B43_WARN_ON(1);
}
}
/* First we set the channel radio code to prevent the
* firmware from sending ghost packets.
*/
channelcookie = channel;
- if (phy->type == B43_PHYTYPE_A)
+ if (0 /*FIXME on 5Ghz */)
channelcookie |= 0x100;
+ //FIXME set 40Mhz flag if required
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_CHAN, channelcookie);
- if (phy->type == B43_PHYTYPE_A) {
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
if (channel > 200)
return -EINVAL;
freq = channel2freq_a(channel);
r8 = b43_radio_read16(dev, 0x0008);
b43_write16(dev, 0x03F0, freq);
@@ -3911,13 +3959,14 @@ int b43_radio_selectchannel(struct b43_w
b43_radio_read16(dev, 0x0035) & 0xFFEF);
b43_radio_write16(dev, 0x0035, (b43_radio_read16(dev, 0x0035)
& 0xFFEF) | 0x0010);
b43_radio_set_tx_iq(dev);
//TODO: TSSI2dbm workaround
b43_phy_xmitpower(dev); //FIXME correct?
- } else {
+ break;
+ case B43_PHYTYPE_G:
if ((channel < 1) || (channel > 14))
return -EINVAL;
if (synthetic_pu_workaround)
b43_synth_pu_workaround(dev, channel);
@@ -3936,12 +3985,18 @@ int b43_radio_selectchannel(struct b43_w
| (1 << 11));
} else {
b43_write16(dev, B43_MMIO_CHANNEL_EXT,
b43_read16(dev, B43_MMIO_CHANNEL_EXT)
& 0xF7BF);
}
+ break;
+ case B43_PHYTYPE_N:
+ b43_nphy_selectchannel(dev, channel);
+ break;
+ default:
+ B43_WARN_ON(1);
}
phy->channel = channel;
/* Wait for the radio to tune to the channel and stabilize. */
msleep(8);
@@ -3982,12 +4037,15 @@ void b43_radio_turn_on(struct b43_wldev
}
channel = phy->channel;
err = b43_radio_selectchannel(dev, B43_DEFAULT_CHANNEL_BG, 1);
err |= b43_radio_selectchannel(dev, channel, 0);
B43_WARN_ON(err);
break;
+ case B43_PHYTYPE_N:
+ b43_nphy_radio_turn_on(dev);
+ break;
default:
B43_WARN_ON(1);
}
phy->radio_on = 1;
}
@@ -3995,28 +4053,35 @@ void b43_radio_turn_off(struct b43_wldev
{
struct b43_phy *phy = &dev->phy;
if (!phy->radio_on && !force)
return;
- if (phy->type == B43_PHYTYPE_A) {
+ switch (phy->type) {
+ case B43_PHYTYPE_N:
+ b43_nphy_radio_turn_off(dev);
+ break;
+ case B43_PHYTYPE_A:
b43_radio_write16(dev, 0x0004, 0x00FF);
b43_radio_write16(dev, 0x0005, 0x00FB);
b43_phy_write(dev, 0x0010, b43_phy_read(dev, 0x0010) | 0x0008);
b43_phy_write(dev, 0x0011, b43_phy_read(dev, 0x0011) | 0x0008);
- }
- if (phy->type == B43_PHYTYPE_G && dev->dev->id.revision >= 5) {
+ break;
+ case B43_PHYTYPE_G: {
u16 rfover, rfoverval;
rfover = b43_phy_read(dev, B43_PHY_RFOVER);
rfoverval = b43_phy_read(dev, B43_PHY_RFOVERVAL);
if (!force) {
phy->radio_off_context.rfover = rfover;
phy->radio_off_context.rfoverval = rfoverval;
phy->radio_off_context.valid = 1;
}
b43_phy_write(dev, B43_PHY_RFOVER, rfover | 0x008C);
b43_phy_write(dev, B43_PHY_RFOVERVAL, rfoverval & 0xFF73);
- } else
- b43_phy_write(dev, 0x0015, 0xAA00);
+ break;
+ }
+ default:
+ B43_WARN_ON(1);
+ }
phy->radio_on = 0;
}
Index: wireless-2.6/drivers/net/wireless/b43/phy.h
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/phy.h 2008-01-13 20:57:36.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/phy.h 2008-01-13 21:02:46.000000000 +0100
@@ -201,14 +201,24 @@ enum {
#define B43_PHYVER_TYPE_SHIFT 8
#define B43_PHYVER_VERSION 0x00FF
void b43_phy_lock(struct b43_wldev *dev);
void b43_phy_unlock(struct b43_wldev *dev);
+
+/* Read a value from a PHY register */
u16 b43_phy_read(struct b43_wldev *dev, u16 offset);
+/* Write a value to a PHY register */
void b43_phy_write(struct b43_wldev *dev, u16 offset, u16 val);
+/* Mask a PHY register with a mask */
+void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask);
+/* OR a PHY register with a bitmap */
+void b43_phy_set(struct b43_wldev *dev, u16 offset, u16 set);
+/* Mask and OR a PHY register with a mask and bitmap */
+void b43_phy_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set);
+
int b43_phy_init_tssi2dbm_table(struct b43_wldev *dev);
void b43_phy_early_init(struct b43_wldev *dev);
int b43_phy_init(struct b43_wldev *dev);
@@ -266,14 +276,24 @@ void b43_phy_set_baseband_attenuation(st
extern const u8 b43_radio_channel_codes_bg[];
void b43_radio_lock(struct b43_wldev *dev);
void b43_radio_unlock(struct b43_wldev *dev);
+
+/* Read a value from a 16bit radio register */
u16 b43_radio_read16(struct b43_wldev *dev, u16 offset);
+/* Write a value to a 16bit radio register */
void b43_radio_write16(struct b43_wldev *dev, u16 offset, u16 val);
+/* Mask a 16bit radio register with a mask */
+void b43_radio_mask(struct b43_wldev *dev, u16 offset, u16 mask);
+/* OR a 16bit radio register with a bitmap */
+void b43_radio_set(struct b43_wldev *dev, u16 offset, u16 set);
+/* Mask and OR a PHY register with a mask and bitmap */
+void b43_radio_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set);
+
u16 b43_radio_init2050(struct b43_wldev *dev);
void b43_radio_init2060(struct b43_wldev *dev);
void b43_radio_turn_on(struct b43_wldev *dev);
void b43_radio_turn_off(struct b43_wldev *dev, bool force);
Index: wireless-2.6/drivers/net/wireless/b43/Makefile
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/Makefile 2008-01-13 20:57:36.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/Makefile 2008-01-13 21:02:46.000000000 +0100
@@ -1,8 +1,9 @@
b43-y += main.o
b43-y += tables.o
+b43-y += tables_nphy.o
b43-y += phy.o
b43-y += nphy.o
b43-y += sysfs.o
b43-y += xmit.o
b43-y += lo.o
b43-y += wa.o
Index: wireless-2.6/drivers/net/wireless/b43/tables_nphy.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ wireless-2.6/drivers/net/wireless/b43/tables_nphy.c 2008-01-13 21:02:46.000000000 +0100
@@ -0,0 +1,292 @@
+/*
+
+ Broadcom B43 wireless driver
+ IEEE 802.11n PHY and radio device data tables
+
+ Copyright (c) 2008 Michael Buesch <mb@xxxxxxxxx>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "tables_nphy.h"
+#include "phy.h"
+#include "nphy.h"
+
+
+struct b2055_inittab_entry {
+ /* Value to write if we use the 5GHz band. */
+ u16 ghz5;
+ /* Value to write if we use the 2.4GHz band. */
+ u16 ghz2;
+ /* Flags */
+ u8 flags;
+#define B2055_INITTAB_ENTRY_OK 0x01
+#define B2055_INITTAB_UPLOAD 0x02
+};
+#define UPLOAD .flags = B2055_INITTAB_ENTRY_OK | B2055_INITTAB_UPLOAD
+#define NOUPLOAD .flags = B2055_INITTAB_ENTRY_OK
+
+static struct b2055_inittab_entry b2055_inittab [] = {
+ [B2055_SP_PINPD] = { .ghz5 = 0x0080, .ghz2 = 0x0080, NOUPLOAD, },
+ [B2055_C1_SP_RSSI] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_SP_PDMISC] = { .ghz5 = 0x0027, .ghz2 = 0x0027, NOUPLOAD, },
+ [B2055_C2_SP_RSSI] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_SP_PDMISC] = { .ghz5 = 0x0027, .ghz2 = 0x0027, NOUPLOAD, },
+ [B2055_C1_SP_RXGC1] = { .ghz5 = 0x007F, .ghz2 = 0x007F, UPLOAD, },
+ [B2055_C1_SP_RXGC2] = { .ghz5 = 0x0007, .ghz2 = 0x0007, UPLOAD, },
+ [B2055_C2_SP_RXGC1] = { .ghz5 = 0x007F, .ghz2 = 0x007F, UPLOAD, },
+ [B2055_C2_SP_RXGC2] = { .ghz5 = 0x0007, .ghz2 = 0x0007, UPLOAD, },
+ [B2055_C1_SP_LPFBWSEL] = { .ghz5 = 0x0015, .ghz2 = 0x0015, NOUPLOAD, },
+ [B2055_C2_SP_LPFBWSEL] = { .ghz5 = 0x0015, .ghz2 = 0x0015, NOUPLOAD, },
+ [B2055_C1_SP_TXGC1] = { .ghz5 = 0x004F, .ghz2 = 0x004F, UPLOAD, },
+ [B2055_C1_SP_TXGC2] = { .ghz5 = 0x0005, .ghz2 = 0x0005, UPLOAD, },
+ [B2055_C2_SP_TXGC1] = { .ghz5 = 0x004F, .ghz2 = 0x004F, UPLOAD, },
+ [B2055_C2_SP_TXGC2] = { .ghz5 = 0x0005, .ghz2 = 0x0005, UPLOAD, },
+ [B2055_MASTER1] = { .ghz5 = 0x00D0, .ghz2 = 0x00D0, NOUPLOAD, },
+ [B2055_MASTER2] = { .ghz5 = 0x0002, .ghz2 = 0x0002, NOUPLOAD, },
+ [B2055_PD_LGEN] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_PD_PLLTS] = { .ghz5 = 0x0040, .ghz2 = 0x0040, NOUPLOAD, },
+ [B2055_C1_PD_LGBUF] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_PD_TX] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_PD_RXTX] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_PD_RSSIMISC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_PD_LGBUF] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_PD_TX] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_PD_RXTX] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_PD_RSSIMISC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_PWRDET_LGEN] = { .ghz5 = 0x00C0, .ghz2 = 0x00C0, NOUPLOAD, },
+ [B2055_C1_PWRDET_LGBUF] = { .ghz5 = 0x00FF, .ghz2 = 0x00FF, NOUPLOAD, },
+ [B2055_C1_PWRDET_RXTX] = { .ghz5 = 0x00C0, .ghz2 = 0x00C0, NOUPLOAD, },
+ [B2055_C2_PWRDET_LGBUF] = { .ghz5 = 0x00FF, .ghz2 = 0x00FF, NOUPLOAD, },
+ [B2055_C2_PWRDET_RXTX] = { .ghz5 = 0x00C0, .ghz2 = 0x00C0, NOUPLOAD, },
+ [B2055_RRCCAL_CS] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_RRCCAL_NOPTSEL] = { .ghz5 = 0x002C, .ghz2 = 0x002C, NOUPLOAD, },
+ [B2055_CAL_MISC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_COUT] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_COUT2] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_CVARCTL] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_RVARCTL] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_LPOCTL] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_TS] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_RCCALRTS] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_CAL_RCALRTS] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_PADDRV] = { .ghz5 = 0x00A4, .ghz2 = 0x00A4, NOUPLOAD, },
+ [B2055_XOCTL1] = { .ghz5 = 0x0038, .ghz2 = 0x0038, NOUPLOAD, },
+ [B2055_XOCTL2] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_XOREGUL] = { .ghz5 = 0x0004, .ghz2 = 0x0004, UPLOAD, },
+ [B2055_XOMISC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_PLL_LFC1] = { .ghz5 = 0x000A, .ghz2 = 0x000A, NOUPLOAD, },
+ [B2055_PLL_CALVTH] = { .ghz5 = 0x0087, .ghz2 = 0x0087, NOUPLOAD, },
+ [B2055_PLL_LFC2] = { .ghz5 = 0x0009, .ghz2 = 0x0009, NOUPLOAD, },
+ [B2055_PLL_REF] = { .ghz5 = 0x0070, .ghz2 = 0x0070, NOUPLOAD, },
+ [B2055_PLL_LFR1] = { .ghz5 = 0x0011, .ghz2 = 0x0011, NOUPLOAD, },
+ [B2055_PLL_PFDCP] = { .ghz5 = 0x0018, .ghz2 = 0x0018, UPLOAD, },
+ [B2055_PLL_IDAC_CPOPAMP] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_PLL_CPREG] = { .ghz5 = 0x0004, .ghz2 = 0x0004, UPLOAD, },
+ [B2055_PLL_RCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_RF_PLLMOD0] = { .ghz5 = 0x009E, .ghz2 = 0x009E, NOUPLOAD, },
+ [B2055_RF_PLLMOD1] = { .ghz5 = 0x0009, .ghz2 = 0x0009, NOUPLOAD, },
+ [B2055_RF_MMDIDAC1] = { .ghz5 = 0x00C8, .ghz2 = 0x00C8, UPLOAD, },
+ [B2055_RF_MMDIDAC0] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_RF_MMDSP] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL1] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL2] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL3] = { .ghz5 = 0x0001, .ghz2 = 0x0001, NOUPLOAD, },
+ [B2055_VCO_CAL4] = { .ghz5 = 0x0002, .ghz2 = 0x0002, NOUPLOAD, },
+ [B2055_VCO_CAL5] = { .ghz5 = 0x0096, .ghz2 = 0x0096, NOUPLOAD, },
+ [B2055_VCO_CAL6] = { .ghz5 = 0x003E, .ghz2 = 0x003E, NOUPLOAD, },
+ [B2055_VCO_CAL7] = { .ghz5 = 0x003E, .ghz2 = 0x003E, NOUPLOAD, },
+ [B2055_VCO_CAL8] = { .ghz5 = 0x0013, .ghz2 = 0x0013, NOUPLOAD, },
+ [B2055_VCO_CAL9] = { .ghz5 = 0x0002, .ghz2 = 0x0002, NOUPLOAD, },
+ [B2055_VCO_CAL10] = { .ghz5 = 0x0015, .ghz2 = 0x0015, NOUPLOAD, },
+ [B2055_VCO_CAL11] = { .ghz5 = 0x0007, .ghz2 = 0x0007, NOUPLOAD, },
+ [B2055_VCO_CAL12] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL13] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL14] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL15] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_CAL16] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_VCO_KVCO] = { .ghz5 = 0x0008, .ghz2 = 0x0008, NOUPLOAD, },
+ [B2055_VCO_CAPTAIL] = { .ghz5 = 0x0008, .ghz2 = 0x0008, NOUPLOAD, },
+ [B2055_VCO_IDACVCO] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_VCO_REG] = { .ghz5 = 0x0084, .ghz2 = 0x0084, UPLOAD, },
+ [B2055_PLL_RFVTH] = { .ghz5 = 0x00C3, .ghz2 = 0x00C3, NOUPLOAD, },
+ [B2055_LGBUF_CENBUF] = { .ghz5 = 0x008F, .ghz2 = 0x008F, NOUPLOAD, },
+ [B2055_LGEN_TUNE1] = { .ghz5 = 0x00FF, .ghz2 = 0x00FF, NOUPLOAD, },
+ [B2055_LGEN_TUNE2] = { .ghz5 = 0x00FF, .ghz2 = 0x00FF, NOUPLOAD, },
+ [B2055_LGEN_IDAC1] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_LGEN_IDAC2] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_LGEN_BIASC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_LGEN_BIASIDAC] = { .ghz5 = 0x00CC, .ghz2 = 0x00CC, NOUPLOAD, },
+ [B2055_LGEN_RCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_LGEN_DIV] = { .ghz5 = 0x0080, .ghz2 = 0x0080, NOUPLOAD, },
+ [B2055_LGEN_SPARE2] = { .ghz5 = 0x0080, .ghz2 = 0x0080, NOUPLOAD, },
+ [B2055_C1_LGBUF_ATUNE] = { .ghz5 = 0x00F8, .ghz2 = 0x00F8, NOUPLOAD, },
+ [B2055_C1_LGBUF_GTUNE] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C1_LGBUF_DIV] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C1_LGBUF_AIDAC] = { .ghz5 = 0x0088, .ghz2 = 0x0008, UPLOAD, },
+ [B2055_C1_LGBUF_GIDAC] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C1_LGBUF_IDACFO] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_LGBUF_SPARE] = { .ghz5 = 0x0001, .ghz2 = 0x0001, UPLOAD, },
+ [B2055_C1_RX_RFSPC1] = { .ghz5 = 0x008A, .ghz2 = 0x008A, NOUPLOAD, },
+ [B2055_C1_RX_RFR1] = { .ghz5 = 0x0008, .ghz2 = 0x0008, NOUPLOAD, },
+ [B2055_C1_RX_RFR2] = { .ghz5 = 0x0083, .ghz2 = 0x0083, NOUPLOAD, },
+ [B2055_C1_RX_RFRCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_C1_RX_BB_BLCMP] = { .ghz5 = 0x00A0, .ghz2 = 0x00A0, NOUPLOAD, },
+ [B2055_C1_RX_BB_LPF] = { .ghz5 = 0x000A, .ghz2 = 0x000A, NOUPLOAD, },
+ [B2055_C1_RX_BB_MIDACHP] = { .ghz5 = 0x0087, .ghz2 = 0x0087, UPLOAD, },
+ [B2055_C1_RX_BB_VGA1IDAC] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C1_RX_BB_VGA2IDAC] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C1_RX_BB_VGA3IDAC] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C1_RX_BB_BUFOCTL] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C1_RX_BB_RCCALCTL] = { .ghz5 = 0x0018, .ghz2 = 0x0018, NOUPLOAD, },
+ [B2055_C1_RX_BB_RSSICTL1] = { .ghz5 = 0x006A, .ghz2 = 0x006A, UPLOAD, },
+ [B2055_C1_RX_BB_RSSICTL2] = { .ghz5 = 0x00AB, .ghz2 = 0x00AB, UPLOAD, },
+ [B2055_C1_RX_BB_RSSICTL3] = { .ghz5 = 0x0013, .ghz2 = 0x0013, UPLOAD, },
+ [B2055_C1_RX_BB_RSSICTL4] = { .ghz5 = 0x00C1, .ghz2 = 0x00C1, UPLOAD, },
+ [B2055_C1_RX_BB_RSSICTL5] = { .ghz5 = 0x00AA, .ghz2 = 0x00AA, UPLOAD, },
+ [B2055_C1_RX_BB_REG] = { .ghz5 = 0x0087, .ghz2 = 0x0087, UPLOAD, },
+ [B2055_C1_RX_BB_SPARE1] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_RX_TXBBRCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_C1_TX_RF_SPGA] = { .ghz5 = 0x0007, .ghz2 = 0x0007, NOUPLOAD, },
+ [B2055_C1_TX_RF_SPAD] = { .ghz5 = 0x0007, .ghz2 = 0x0007, NOUPLOAD, },
+ [B2055_C1_TX_RF_CNTPGA1] = { .ghz5 = 0x0015, .ghz2 = 0x0015, NOUPLOAD, },
+ [B2055_C1_TX_RF_CNTPAD1] = { .ghz5 = 0x0055, .ghz2 = 0x0055, NOUPLOAD, },
+ [B2055_C1_TX_RF_PGAIDAC] = { .ghz5 = 0x0097, .ghz2 = 0x0097, UPLOAD, },
+ [B2055_C1_TX_PGAPADTN] = { .ghz5 = 0x0008, .ghz2 = 0x0008, NOUPLOAD, },
+ [B2055_C1_TX_PADIDAC1] = { .ghz5 = 0x0014, .ghz2 = 0x0014, UPLOAD, },
+ [B2055_C1_TX_PADIDAC2] = { .ghz5 = 0x0033, .ghz2 = 0x0033, NOUPLOAD, },
+ [B2055_C1_TX_MXBGTRIM] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C1_TX_RF_RCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_C1_TX_RF_PADTSSI1] = { .ghz5 = 0x0003, .ghz2 = 0x0003, UPLOAD, },
+ [B2055_C1_TX_RF_PADTSSI2] = { .ghz5 = 0x000A, .ghz2 = 0x000A, NOUPLOAD, },
+ [B2055_C1_TX_RF_SPARE] = { .ghz5 = 0x0003, .ghz2 = 0x0003, UPLOAD, },
+ [B2055_C1_TX_RF_IQCAL1] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C1_TX_RF_IQCAL2] = { .ghz5 = 0x00A4, .ghz2 = 0x00A4, NOUPLOAD, },
+ [B2055_C1_TXBB_RCCAL] = { .ghz5 = 0x0018, .ghz2 = 0x0018, NOUPLOAD, },
+ [B2055_C1_TXBB_LPF1] = { .ghz5 = 0x0028, .ghz2 = 0x0028, NOUPLOAD, },
+ [B2055_C1_TX_VOSCNCL] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_TX_LPF_MXGMIDAC] = { .ghz5 = 0x004A, .ghz2 = 0x004A, NOUPLOAD, },
+ [B2055_C1_TX_BB_MXGM] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_LGBUF_ATUNE] = { .ghz5 = 0x00F8, .ghz2 = 0x00F8, NOUPLOAD, },
+ [B2055_C2_LGBUF_GTUNE] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C2_LGBUF_DIV] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C2_LGBUF_AIDAC] = { .ghz5 = 0x0088, .ghz2 = 0x0008, UPLOAD, },
+ [B2055_C2_LGBUF_GIDAC] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C2_LGBUF_IDACFO] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_LGBUF_SPARE] = { .ghz5 = 0x0001, .ghz2 = 0x0001, UPLOAD, },
+ [B2055_C2_RX_RFSPC1] = { .ghz5 = 0x008A, .ghz2 = 0x008A, NOUPLOAD, },
+ [B2055_C2_RX_RFR1] = { .ghz5 = 0x0008, .ghz2 = 0x0008, NOUPLOAD, },
+ [B2055_C2_RX_RFR2] = { .ghz5 = 0x0083, .ghz2 = 0x0083, NOUPLOAD, },
+ [B2055_C2_RX_RFRCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_C2_RX_BB_BLCMP] = { .ghz5 = 0x00A0, .ghz2 = 0x00A0, NOUPLOAD, },
+ [B2055_C2_RX_BB_LPF] = { .ghz5 = 0x000A, .ghz2 = 0x000A, NOUPLOAD, },
+ [B2055_C2_RX_BB_MIDACHP] = { .ghz5 = 0x0087, .ghz2 = 0x0087, UPLOAD, },
+ [B2055_C2_RX_BB_VGA1IDAC] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C2_RX_BB_VGA2IDAC] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C2_RX_BB_VGA3IDAC] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C2_RX_BB_BUFOCTL] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C2_RX_BB_RCCALCTL] = { .ghz5 = 0x0018, .ghz2 = 0x0018, NOUPLOAD, },
+ [B2055_C2_RX_BB_RSSICTL1] = { .ghz5 = 0x006A, .ghz2 = 0x006A, UPLOAD, },
+ [B2055_C2_RX_BB_RSSICTL2] = { .ghz5 = 0x00AB, .ghz2 = 0x00AB, UPLOAD, },
+ [B2055_C2_RX_BB_RSSICTL3] = { .ghz5 = 0x0013, .ghz2 = 0x0013, UPLOAD, },
+ [B2055_C2_RX_BB_RSSICTL4] = { .ghz5 = 0x00C1, .ghz2 = 0x00C1, UPLOAD, },
+ [B2055_C2_RX_BB_RSSICTL5] = { .ghz5 = 0x00AA, .ghz2 = 0x00AA, UPLOAD, },
+ [B2055_C2_RX_BB_REG] = { .ghz5 = 0x0087, .ghz2 = 0x0087, UPLOAD, },
+ [B2055_C2_RX_BB_SPARE1] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_RX_TXBBRCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_C2_TX_RF_SPGA] = { .ghz5 = 0x0007, .ghz2 = 0x0007, NOUPLOAD, },
+ [B2055_C2_TX_RF_SPAD] = { .ghz5 = 0x0007, .ghz2 = 0x0007, NOUPLOAD, },
+ [B2055_C2_TX_RF_CNTPGA1] = { .ghz5 = 0x0015, .ghz2 = 0x0015, NOUPLOAD, },
+ [B2055_C2_TX_RF_CNTPAD1] = { .ghz5 = 0x0055, .ghz2 = 0x0055, NOUPLOAD, },
+ [B2055_C2_TX_RF_PGAIDAC] = { .ghz5 = 0x0097, .ghz2 = 0x0097, UPLOAD, },
+ [B2055_C2_TX_PGAPADTN] = { .ghz5 = 0x0008, .ghz2 = 0x0008, NOUPLOAD, },
+ [B2055_C2_TX_PADIDAC1] = { .ghz5 = 0x0014, .ghz2 = 0x0014, UPLOAD, },
+ [B2055_C2_TX_PADIDAC2] = { .ghz5 = 0x0033, .ghz2 = 0x0033, NOUPLOAD, },
+ [B2055_C2_TX_MXBGTRIM] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [B2055_C2_TX_RF_RCAL] = { .ghz5 = 0x0006, .ghz2 = 0x0006, NOUPLOAD, },
+ [B2055_C2_TX_RF_PADTSSI1] = { .ghz5 = 0x0003, .ghz2 = 0x0003, UPLOAD, },
+ [B2055_C2_TX_RF_PADTSSI2] = { .ghz5 = 0x000A, .ghz2 = 0x000A, NOUPLOAD, },
+ [B2055_C2_TX_RF_SPARE] = { .ghz5 = 0x0003, .ghz2 = 0x0003, UPLOAD, },
+ [B2055_C2_TX_RF_IQCAL1] = { .ghz5 = 0x002A, .ghz2 = 0x002A, NOUPLOAD, },
+ [B2055_C2_TX_RF_IQCAL2] = { .ghz5 = 0x00A4, .ghz2 = 0x00A4, NOUPLOAD, },
+ [B2055_C2_TXBB_RCCAL] = { .ghz5 = 0x0018, .ghz2 = 0x0018, NOUPLOAD, },
+ [B2055_C2_TXBB_LPF1] = { .ghz5 = 0x0028, .ghz2 = 0x0028, NOUPLOAD, },
+ [B2055_C2_TX_VOSCNCL] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_TX_LPF_MXGMIDAC] = { .ghz5 = 0x004A, .ghz2 = 0x004A, NOUPLOAD, },
+ [B2055_C2_TX_BB_MXGM] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_PRG_GCHP21] = { .ghz5 = 0x0071, .ghz2 = 0x0071, NOUPLOAD, },
+ [B2055_PRG_GCHP22] = { .ghz5 = 0x0072, .ghz2 = 0x0072, NOUPLOAD, },
+ [B2055_PRG_GCHP23] = { .ghz5 = 0x0073, .ghz2 = 0x0073, NOUPLOAD, },
+ [B2055_PRG_GCHP24] = { .ghz5 = 0x0074, .ghz2 = 0x0074, NOUPLOAD, },
+ [B2055_PRG_GCHP25] = { .ghz5 = 0x0075, .ghz2 = 0x0075, NOUPLOAD, },
+ [B2055_PRG_GCHP26] = { .ghz5 = 0x0076, .ghz2 = 0x0076, NOUPLOAD, },
+ [B2055_PRG_GCHP27] = { .ghz5 = 0x0077, .ghz2 = 0x0077, NOUPLOAD, },
+ [B2055_PRG_GCHP28] = { .ghz5 = 0x0078, .ghz2 = 0x0078, NOUPLOAD, },
+ [B2055_PRG_GCHP29] = { .ghz5 = 0x0079, .ghz2 = 0x0079, NOUPLOAD, },
+ [B2055_PRG_GCHP30] = { .ghz5 = 0x007A, .ghz2 = 0x007A, NOUPLOAD, },
+ [0xC7] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xC8] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xC9] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xCA] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xCB] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xCC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_LNA_GAINBST] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xCE] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xCF] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xD0] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xD1] = { .ghz5 = 0x0018, .ghz2 = 0x0018, NOUPLOAD, },
+ [B2055_C1_B0NB_RSSIVCM] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [0xD3] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xD4] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xD5] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C1_GENSPARE2] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xD7] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xD8] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_LNA_GAINBST] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xDA] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xDB] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xDC] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xDD] = { .ghz5 = 0x0018, .ghz2 = 0x0018, NOUPLOAD, },
+ [B2055_C2_B0NB_RSSIVCM] = { .ghz5 = 0x0088, .ghz2 = 0x0088, NOUPLOAD, },
+ [0xDF] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xE0] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [0xE1] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+ [B2055_C2_GENSPARE2] = { .ghz5 = 0x0000, .ghz2 = 0x0000, NOUPLOAD, },
+};
+
+
+void b2055_upload_inittab(struct b43_wldev *dev,
+ bool ghz5, bool ignore_uploadflag)
+{
+ struct b2055_inittab_entry *e;
+ unsigned int i;
+ u16 value;
+
+ for (i = 0; i < ARRAY_SIZE(b2055_inittab); i++) {
+ e = &(b2055_inittab[i]);
+ if (!(e->flags & B2055_INITTAB_ENTRY_OK))
+ continue;
+ if ((e->flags & B2055_INITTAB_UPLOAD) || ignore_uploadflag) {
+ if (ghz5)
+ value = e->ghz5;
+ else
+ value = e->ghz2;
+ b43_radio_write16(dev, i, value);
+ }
+ }
+}
Index: wireless-2.6/drivers/net/wireless/b43/tables_nphy.h
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ wireless-2.6/drivers/net/wireless/b43/tables_nphy.h 2008-01-13 21:02:46.000000000 +0100
@@ -0,0 +1,17 @@
+#ifndef B43_TABLES_NPHY_H_
+#define B43_TABLES_NPHY_H_
+
+#include <linux/types.h>
+
+
+struct b43_wldev;
+
+/* Upload the default register value table.
+ * If "ghz5" is true, we upload the 5Ghz table. Otherwise the 2.4Ghz
+ * table is uploaded. If "ignore_uploadflag" is true, we upload any value
+ * and ignore the "UPLOAD" flag. */
+void b2055_upload_inittab(struct b43_wldev *dev,
+ bool ghz5, bool ignore_uploadflag);
+
+
+#endif /* B43_TABLES_NPHY_H_ */
Index: wireless-2.6/drivers/net/wireless/b43/main.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/main.c 2008-01-13 20:57:36.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/main.c 2008-01-13 21:02:46.000000000 +0100
@@ -2129,12 +2129,13 @@ static void b43_rate_memory_write(struct
static void b43_rate_memory_init(struct b43_wldev *dev)
{
switch (dev->phy.type) {
case B43_PHYTYPE_A:
case B43_PHYTYPE_G:
+ case B43_PHYTYPE_N:
b43_rate_memory_write(dev, B43_OFDM_RATE_6MB, 1);
b43_rate_memory_write(dev, B43_OFDM_RATE_12MB, 1);
b43_rate_memory_write(dev, B43_OFDM_RATE_18MB, 1);
b43_rate_memory_write(dev, B43_OFDM_RATE_24MB, 1);
b43_rate_memory_write(dev, B43_OFDM_RATE_36MB, 1);
b43_rate_memory_write(dev, B43_OFDM_RATE_48MB, 1);
@@ -2317,12 +2318,14 @@ static void b43_periodic_every120sec(str
}
static void b43_periodic_every60sec(struct b43_wldev *dev)
{
struct b43_phy *phy = &dev->phy;
+ if (phy->type != B43_PHYTYPE_G)
+ return;
if (!b43_has_hardware_pctl(phy))
b43_lo_g_ctl_mark_all_unused(dev);
if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) {
b43_mac_suspend(dev);
b43_calc_nrssi_slope(dev);
if ((phy->radio_ver == 0x2050) && (phy->radio_rev == 8)) {
-
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
