Please stop top posting A: Because we read from top to bottom, left to right. Q: Why should I start my reply below the quoted text? A: Because it messes up the order in which people normally read text. Q: Why is top-posting such a bad thing? A: The lost context. Q: What makes top-posted replies harder to read than bottom-posted? A: Yes. Q: Should I trim down the quoted part of an email to which I'm replying? http://www.idallen.com/topposting.html On 12/27/2012 07:26 AM, spameden wrote: > Hi guys I have the same device. > > I'm wondering if it's fully supported or not by b43 driver. > > Here > http://linuxwireless.org/en/users/Drivers/b43?highlight=%2814e4%29#Supported_devices > I can see it's listed as supported in N-phy, but as Aitor said on > OpenWRT only b/g mode supported for some reason.. n-phy is the name of the phy, the hardware supports ieee80211n, but b43 does not support ieee80211n at all. > I can provide all needed info for this device, I have it in my old ASUS > WL-500gP v1. > > On the other note there is a leaked broadcom source of wl driver from > Belkin F7D4401 v1.00.39 (it was posted online), I hope it helps: We already have a spec for this phy and the n specific stuff should also be in the phy code b43 uses, someone has just to add support for ieee80211n to b43 in general. > http://uploadmirrors.com/download/XLVMMGAJ/Belkin-F7D4401-v1.00.39.tar.7z > http://www.mirrorcreator.com/files/1DJEOCRJ/Belkin-F7D4401-v1.00.39.tar.7z_links > http://www.digzip.com/files/1L27MJRC/Belkin-F7D4401-v1.00.39.tar.7z > http://www.multiupload.nl/P6B0GK9U6R > > hopefully it'd help. > > 2012/10/27 Aitor Cuartango <aitor.cuartango@xxxxxxxxx > <mailto:aitor.cuartango@xxxxxxxxx>> > > If you need more information about the device let me know. > > With the last openwrt's trunk i can create a wifi network but only > in b/g mode. > > I've test editing manually /etc/config/wireless and change : > option hwmode '11g' > with > option hwmode '11ng' > > but it does not starts, perhaps i need to do more changes in this > file... > > > Thanks all! > aitor > > > 2012/10/25 Hauke Mehrtens <hauke@xxxxxxxxxx <mailto:hauke@xxxxxxxxxx>>: > > On 10/25/2012 06:47 PM, Rafał Miłecki wrote: > >> 2012/10/25 Hauke Mehrtens <hauke@xxxxxxxxxx > <mailto:hauke@xxxxxxxxxx>>: > >>> 14e4:4350 is found on a Broadcom BCM43222. > >> > >> Huh, I expected BCM43222 to be BCMA based, interesting. Could you > >> provide ssb log for scanning (cores listing) and PHY&RADIO info? > >> > > > > It is not my device, but Aitor found it, here are the details: > > http://comments.gmane.org/gmane.comp.embedded.openwrt.user/2031 > > > > Here is the log you requested, without the patches: > > ... > > b43-pci-bridge 0000:00:02.0: setting latency timer to 64 > > ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 > > ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243) > > ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243) > > ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243) > > ssb: chipcommon status is 0x40040 > > ssb: Found rev 2 PMU (capabilities 0x044C3002) > > ssb: ERROR: PLL init unknown for device A8D6 > > ssb: ERROR: PMU resource config unknown for device A8D6 > > ssb: SPROM offset is 0x1000 > > ssb: SPROM revision 8 detected. > > b43-phy0: Broadcom 43222 WLAN found (core revision 16) > > ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0 > > ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' > > ... > > > > Hauke -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
