Larry Finger a écrit :
Matthieu PATOU wrote:
And it keeps looping around the same set of message.
Any clue on to solve this problem ?
Any patch that i can test ?
These messages should only arise if you were using an unpatched kernel.
Are you sure you put the patch in correctly?
The results reported was with your previous patch, because the second version didn't show good results when I first tried.
So I tried the previous, which obviously didn't do the job neither !
So i removed the first patch, applied the second, checked, rebuild the modules, reboot the notebook a couple of time but
I still have DMA errors.
I attached the result of my dmesg and the patch I use in case i took the wrong one.
I checked right now that this patch is really applied with this command :
mat@ares:/usr/local/src/linux-2.6.24-git# patch -p1 --dry-run -R <../patchs/patch_bcm4312_2
patching file drivers/net/wireless/b43/dma.c
patching file drivers/net/wireless/b43/main.c
patching file drivers/net/wireless/b43/wa.c
HTH
Matthieu.
dma.c | 86 ++++++++++++++++++++++++++++++++++-------------------------------
main.c | 3 +-
wa.c | 1
3 files changed, 49 insertions(+), 41 deletions(-)
Index: wireless-2.6/drivers/net/wireless/b43/dma.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/dma.c
+++ wireless-2.6/drivers/net/wireless/b43/dma.c
@@ -165,7 +165,7 @@ static void op64_fill_descriptor(struct
addrhi = (((u64) dmaaddr >> 32) & ~SSB_DMA_TRANSLATION_MASK);
addrext = (((u64) dmaaddr >> 32) & SSB_DMA_TRANSLATION_MASK)
>> SSB_DMA_TRANSLATION_SHIFT;
- addrhi |= ssb_dma_translation(ring->dev->dev);
+ addrhi |= (ssb_dma_translation(ring->dev->dev) << 1);
if (slot == ring->nr_slots - 1)
ctl0 |= B43_DMA64_DCTL0_DTABLEEND;
if (start)
@@ -426,9 +426,20 @@ static inline
static int alloc_ringmemory(struct b43_dmaring *ring)
{
struct device *dev = ring->dev->dev->dev;
+ gfp_t flags = GFP_KERNEL;
+ /* The specs call for 4K buffers for 30- and 32-bit DMA
+ * and 8K buffers for 64-bit DMA; however, 4K is sufficient for
+ * the latter as long as the buffer does not cross an 8K boundary.
+ *
+ * For unknown reasons - possibly a hardware error - the BCM4311 rev
+ * 02, which uses 64-bit DMA, needs the ring buffer in very low memory,
+ * which accounts for the GFP_DMA flag below.
+ */
+ if (ring->dma64)
+ flags = GFP_DMA;
ring->descbase = dma_alloc_coherent(dev, B43_DMA_RINGMEMSIZE,
- &(ring->dmabase), GFP_KERNEL);
+ &(ring->dmabase), flags);
if (!ring->descbase) {
b43err(ring->dev->wl, "DMA ringmemory allocation failed\n");
return -ENOMEM;
@@ -483,7 +494,7 @@ int b43_dmacontroller_rx_reset(struct b4
return 0;
}
-/* Reset the RX DMA channel */
+/* Reset the TX DMA channel */
int b43_dmacontroller_tx_reset(struct b43_wldev *dev, u16 mmio_base, int dma64)
{
int i;
@@ -636,18 +647,12 @@ static int dmacontroller_setup(struct b4
if (ring->dma64) {
u64 ringbase = (u64) (ring->dmabase);
- addrext = ((ringbase >> 32) & SSB_DMA_TRANSLATION_MASK)
- >> SSB_DMA_TRANSLATION_SHIFT;
- value = B43_DMA64_TXENABLE;
- value |= (addrext << B43_DMA64_TXADDREXT_SHIFT)
- & B43_DMA64_TXADDREXT_MASK;
- b43_dma_write(ring, B43_DMA64_TXCTL, value);
+ b43_dma_write(ring, B43_DMA64_TXCTL,
+ B43_DMA64_TXENABLE);
b43_dma_write(ring, B43_DMA64_TXRINGLO,
(ringbase & 0xFFFFFFFF));
b43_dma_write(ring, B43_DMA64_TXRINGHI,
- ((ringbase >> 32) &
- ~SSB_DMA_TRANSLATION_MASK)
- | trans);
+ (ringbase >> 32));
} else {
u32 ringbase = (u32) (ring->dmabase);
@@ -668,20 +673,15 @@ static int dmacontroller_setup(struct b4
if (ring->dma64) {
u64 ringbase = (u64) (ring->dmabase);
- addrext = ((ringbase >> 32) & SSB_DMA_TRANSLATION_MASK)
- >> SSB_DMA_TRANSLATION_SHIFT;
- value = (ring->frameoffset << B43_DMA64_RXFROFF_SHIFT);
- value |= B43_DMA64_RXENABLE;
- value |= (addrext << B43_DMA64_RXADDREXT_SHIFT)
- & B43_DMA64_RXADDREXT_MASK;
+ value = (ring->frameoffset << B43_DMA64_RXFROFF_SHIFT)
+ | B43_DMA64_RXENABLE;
b43_dma_write(ring, B43_DMA64_RXCTL, value);
b43_dma_write(ring, B43_DMA64_RXRINGLO,
(ringbase & 0xFFFFFFFF));
b43_dma_write(ring, B43_DMA64_RXRINGHI,
- ((ringbase >> 32) &
- ~SSB_DMA_TRANSLATION_MASK)
- | trans);
- b43_dma_write(ring, B43_DMA64_RXINDEX, 200);
+ (ringbase >> 32));
+ b43_dma_write(ring, B43_DMA64_RXINDEX, ring->nr_slots *
+ sizeof(struct b43_dmadesc64));
} else {
u32 ringbase = (u32) (ring->dmabase);
@@ -695,11 +695,12 @@ static int dmacontroller_setup(struct b4
b43_dma_write(ring, B43_DMA32_RXRING,
(ringbase & ~SSB_DMA_TRANSLATION_MASK)
| trans);
- b43_dma_write(ring, B43_DMA32_RXINDEX, 200);
+ b43_dma_write(ring, B43_DMA32_RXINDEX, ring->nr_slots *
+ sizeof(struct b43_dmadesc32));
}
}
- out:
+out:
return err;
}
@@ -954,19 +955,21 @@ int b43_dma_init(struct b43_wldev *dev)
err = -ENOMEM;
/* setup TX DMA channels. */
- ring = b43_setup_dmaring(dev, 0, 1, dma64);
+ ring = b43_setup_dmaring(dev, 1, 1, dma64);
if (!ring)
goto out;
- dma->tx_ring0 = ring;
+ dma->tx_ring1 = ring;
- ring = b43_setup_dmaring(dev, 1, 1, dma64);
+ /* The driver only uses ring1 for TX - skip setup for the rest */
+#if 0
+ ring = b43_setup_dmaring(dev, 0, 1, dma64);
if (!ring)
- goto err_destroy_tx0;
- dma->tx_ring1 = ring;
+ goto err_destroy_tx1;
+ dma->tx_ring0 = ring;
ring = b43_setup_dmaring(dev, 2, 1, dma64);
if (!ring)
- goto err_destroy_tx1;
+ goto err_destroy_tx0;
dma->tx_ring2 = ring;
ring = b43_setup_dmaring(dev, 3, 1, dma64);
@@ -983,6 +986,7 @@ int b43_dma_init(struct b43_wldev *dev)
if (!ring)
goto err_destroy_tx4;
dma->tx_ring5 = ring;
+#endif
/* setup RX DMA channels. */
ring = b43_setup_dmaring(dev, 0, 0, dma64);
@@ -1001,30 +1005,32 @@ int b43_dma_init(struct b43_wldev *dev)
(dmamask == DMA_64BIT_MASK) ? 64 :
(dmamask == DMA_32BIT_MASK) ? 32 : 30);
err = 0;
- out:
+out:
return err;
- err_destroy_rx0:
+err_destroy_rx0:
b43_destroy_dmaring(dma->rx_ring0);
dma->rx_ring0 = NULL;
- err_destroy_tx5:
+err_destroy_tx5:
+#if 0
b43_destroy_dmaring(dma->tx_ring5);
dma->tx_ring5 = NULL;
- err_destroy_tx4:
+err_destroy_tx4:
b43_destroy_dmaring(dma->tx_ring4);
dma->tx_ring4 = NULL;
- err_destroy_tx3:
+err_destroy_tx3:
b43_destroy_dmaring(dma->tx_ring3);
dma->tx_ring3 = NULL;
- err_destroy_tx2:
+err_destroy_tx2:
b43_destroy_dmaring(dma->tx_ring2);
dma->tx_ring2 = NULL;
- err_destroy_tx1:
- b43_destroy_dmaring(dma->tx_ring1);
- dma->tx_ring1 = NULL;
- err_destroy_tx0:
+err_destroy_tx0:
b43_destroy_dmaring(dma->tx_ring0);
dma->tx_ring0 = NULL;
+err_destroy_tx1:
+#endif
+ b43_destroy_dmaring(dma->tx_ring1);
+ dma->tx_ring1 = NULL;
goto out;
}
Index: wireless-2.6/drivers/net/wireless/b43/main.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/main.c
+++ wireless-2.6/drivers/net/wireless/b43/main.c
@@ -93,6 +93,7 @@ static const struct ssb_device_id b43_ss
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 7),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 9),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 10),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 13),
SSB_DEVTABLE_END
};
@@ -3064,7 +3065,7 @@ static int b43_phy_versioning(struct b43
unsupported = 1;
break;
case B43_PHYTYPE_G:
- if (phy_rev > 8)
+ if (phy_rev > 9)
unsupported = 1;
break;
default:
Index: wireless-2.6/drivers/net/wireless/b43/wa.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/wa.c
+++ wireless-2.6/drivers/net/wireless/b43/wa.c
@@ -642,6 +642,7 @@ void b43_wa_all(struct b43_wldev *dev)
case 6:
case 7:
case 8:
+ case 9:
b43_wa_tr_ltov(dev);
b43_wa_crs_ed(dev);
b43_wa_rssi_lt(dev);
-
[ 0.000000] Linux version 2.6.24-rc3-ares (root@ares) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Thu Nov 22 20:31:05 MSK 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000077fb0000 (usable)
[ 0.000000] BIOS-e820: 0000000077fb0000 - 0000000077fc8000 (reserved)
[ 0.000000] BIOS-e820: 0000000077fc8000 - 0000000077fe7fb8 (ACPI NVS)
[ 0.000000] BIOS-e820: 0000000077fe7fb8 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffbc0000 - 00000000ffcc0000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] 1023MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 491440) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 491440
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 491440
[ 0.000000] On node 0 totalpages: 491440
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2047 pages used for memmap
[ 0.000000] HighMem zone: 260017 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000FE0B0, 0024 (r2 HP )
[ 0.000000] ACPI: XSDT 77FC81BC, 0064 (r1 HPQOEM SLIC-MPC 1 HP 1)
[ 0.000000] ACPI: FACP 77FC8084, 00F4 (r4 HP 0944 3 HP 1)
[ 0.000000] ACPI Error (tbfadt-0453): 32/64X address mismatch in "Pm2ControlBlock": [00008800] [0000000000008100], using 64X [20070126]
[ 0.000000] ACPI: DSDT 77FC84A4, 11437 (r1 HP SB400 10000 MSFT 3000001)
[ 0.000000] ACPI: FACS 77FE7D80, 0040
[ 0.000000] ACPI: SLIC 77FC8220, 0176 (r1 HPQOEM SLIC-MPC 1 HP 1)
[ 0.000000] ACPI: EPTH 77FC8398, 0038 (r1 HP 0944 1 HP 1)
[ 0.000000] ACPI: APIC 77FC83D0, 0062 (r1 HP 0944 1 HP 1)
[ 0.000000] ACPI: MCFG 77FC8434, 003C (r1 HP 0944 1 HP 1)
[ 0.000000] ACPI: TCPA 77FC8470, 0032 (r2 HP 0944 1 HP 1)
[ 0.000000] ACPI: SSDT 77FD98DB, 0059 (r1 HP HPQNLP 1 MSFT 3000001)
[ 0.000000] ACPI: SSDT 77FD9934, 0206 (r1 HP PSSTBLID 1 HP 1)
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 487601
[ 0.000000] Kernel command line: root=UUID=c7767a2d-354a-4a6a-b52a-43e1cae66973 ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1995.037 MHz processor.
[ 26.365127] Console: colour VGA+ 80x25
[ 26.365130] console [tty0] enabled
[ 26.370562] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 26.371358] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 26.524443] Memory: 1940136k/1965760k available (1949k kernel code, 24424k reserved, 946k data, 220k init, 1048256k highmem)
[ 26.524545] virtual kernel memory layout:
[ 26.524546] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 26.524547] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 26.524548] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 26.524550] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 26.524551] .init : 0xc03d9000 - 0xc0410000 ( 220 kB)
[ 26.524552] .data : 0xc02e74f6 - 0xc03d3d84 ( 946 kB)
[ 26.524553] .text : 0xc0100000 - 0xc02e74f6 (1949 kB)
[ 26.525176] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 26.525401] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 26.605477] Calibrating delay using timer specific routine.. 3997.94 BogoMIPS (lpj=7995896)
[ 26.605676] Security Framework initialized
[ 26.605751] SELinux: Disabled at boot.
[ 26.605849] Mount-cache hash table entries: 512
[ 26.606141] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
[ 26.606165] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 26.606240] CPU: L2 Cache: 512K (64 bytes/line)
[ 26.606330] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
[ 26.606338] Compat vDSO mapped to ffffe000.
[ 26.606435] Checking 'hlt' instruction... OK.
[ 26.621954] SMP alternatives: switching to UP code
[ 26.622912] ACPI: Core revision 20070126
[ 26.711975] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 01
[ 26.712093] SMP alternatives: switching to SMP code
[ 26.712493] Booting processor 1/1 eip 3000
[ 26.721030] Initializing CPU#1
[ 26.799856] Calibrating delay using timer specific routine.. 3990.34 BogoMIPS (lpj=7980692)
[ 26.799862] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
[ 26.799867] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 26.799869] CPU: L2 Cache: 512K (64 bytes/line)
[ 26.799871] AMD C1E detected late. Force timer broadcast.
[ 26.799873] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
[ 26.801583] CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 01
[ 26.801876] Total of 2 processors activated (7988.29 BogoMIPS).
[ 26.802055] ENABLING IO-APIC IRQs
[ 26.802256] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 26.842039] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 26.842077] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 26.842146] ...trying to set up timer as Virtual Wire IRQ... works.
[ 26.882076] Brought up 2 CPUs
[ 26.882131] CPU0 attaching sched-domain:
[ 26.882133] domain 0: span 03
[ 26.882135] groups: 01 02
[ 26.882138] CPU1 attaching sched-domain:
[ 26.882139] domain 0: span 03
[ 26.882141] groups: 02 01
[ 26.882327] net_namespace: 64 bytes
[ 26.882373] HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
[ 26.882863] NET: Registered protocol family 16
[ 26.883037] ACPI: bus type pci registered
[ 26.883151] PCI: Using MMCONFIG
[ 26.883222] PCI: No mmconfig possible on device 00:18
[ 26.883827] Setting up standard PCI resources
[ 26.885605] ACPI: EC: Look up EC in DSDT
[ 26.884739] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 27.125082] ACPI: Interpreter enabled
[ 27.125120] ACPI: (supports S0 S3 S4 S5)
[ 27.125287] ACPI: Using IOAPIC for interrupt routing
[ 27.132662] ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
[ 27.132702] ACPI: EC: driver started in interrupt mode
[ 27.132787] ACPI: PCI Root Bridge [C08B] (0000:00)
[ 27.134272] PCI: Transparent bridge - 0000:00:14.4
[ 27.134401] ACPI: PCI Interrupt Routing Table [\_SB_.C08B._PRT]
[ 27.134665] ACPI: PCI Interrupt Routing Table [\_SB_.C08B.C08C._PRT]
[ 27.134770] ACPI: PCI Interrupt Routing Table [\_SB_.C08B.C0FC._PRT]
[ 27.153338] ACPI: PCI Interrupt Link [C145] (IRQs 10 11) *0, disabled.
[ 27.153706] ACPI: PCI Interrupt Link [C146] (IRQs 10 11) *0, disabled.
[ 27.154069] ACPI: PCI Interrupt Link [C147] (IRQs 10 11) *0, disabled.
[ 27.154434] ACPI: PCI Interrupt Link [C148] (IRQs 10 11) *0, disabled.
[ 27.154800] ACPI: PCI Interrupt Link [C149] (IRQs 10 11) *0, disabled.
[ 27.155164] ACPI: PCI Interrupt Link [C14A] (IRQs 9) *0, disabled.
[ 27.155499] ACPI: PCI Interrupt Link [C14B] (IRQs 10 11) *0, disabled.
[ 27.155863] ACPI: PCI Interrupt Link [C14C] (IRQs 10 11) *0, disabled.
[ 27.156203] ACPI: Power Resource [C171] (off)
[ 27.156287] ACPI: Power Resource [C24C] (on)
[ 27.156433] ACPI: Power Resource [C395] (off)
[ 27.156556] ACPI: Power Resource [C396] (off)
[ 27.156679] ACPI: Power Resource [C397] (off)
[ 27.156802] ACPI: Power Resource [C398] (off)
[ 27.156884] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 27.156946] pnp: PnP ACPI init
[ 27.156987] ACPI: bus type pnp registered
[ 27.163088] pnp: PnP ACPI: found 12 devices
[ 27.163126] ACPI: ACPI bus type pnp unregistered
[ 27.163264] PCI: Using ACPI for IRQ routing
[ 27.163301] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 27.163373] PCI: Cannot allocate resource region 0 of device 0000:00:14.2
[ 27.192337] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 27.192377] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 27.192415] system 00:00: iomem range 0x100000-0xffffffff could not be reserved
[ 27.192463] system 00:08: ioport range 0x40b-0x40b has been reserved
[ 27.192502] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 27.192542] system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 27.192585] system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
[ 27.192630] system 00:0a: ioport range 0x8000-0x802f has been reserved
[ 27.192669] system 00:0a: ioport range 0x8100-0x811f has been reserved
[ 27.192708] system 00:0a: iomem range 0xe0000000-0xefffffff could not be reserved
[ 27.192751] system 00:0a: iomem range 0xfec00000-0xfec000ff could not be reserved
[ 27.192794] system 00:0a: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 27.192836] system 00:0b: iomem range 0xcd400-0xcffff has been reserved
[ 27.192875] system 00:0b: iomem range 0x0-0x7ffffff could not be reserved
[ 27.192914] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[ 27.223313] PCI: Bridge: 0000:00:01.0
[ 27.223351] IO window: 4000-4fff
[ 27.223389] MEM window: d0400000-d05fffff
[ 27.223426] PREFETCH window: c0000000-c7ffffff
[ 27.223465] PCI: Bridge: 0000:00:04.0
[ 27.223501] IO window: disabled.
[ 27.223540] MEM window: d0000000-d00fffff
[ 27.223577] PREFETCH window: disabled.
[ 27.223614] PCI: Bridge: 0000:00:05.0
[ 27.223652] IO window: 2000-3fff
[ 27.223689] MEM window: cc000000-cfffffff
[ 27.223726] PREFETCH window: disabled.
[ 27.223764] PCI: Bridge: 0000:00:06.0
[ 27.223801] IO window: disabled.
[ 27.223838] MEM window: c8000000-c80fffff
[ 27.223876] PREFETCH window: disabled.
[ 27.223917] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[ 27.223956] IO window: 00001000-000010ff
[ 27.225808] Time: acpi_pm clocksource has been installed.
[ 27.225811] Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 27.225813] Could not switch to high resolution mode on CPU 0
[ 27.224904] Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 27.224978] Could not switch to high resolution mode on CPU 1
[ 27.225019] IO window: 00001400-000014ff
[ 27.225059] PREFETCH window: 8c000000-8fffffff
[ 27.225099] MEM window: 90000000-93ffffff
[ 27.225138] PCI: Bridge: 0000:00:14.4
[ 27.225174] IO window: disabled.
[ 27.225213] MEM window: d0100000-d03fffff
[ 27.225252] PREFETCH window: disabled.
[ 27.225302] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 27.225308] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 27.225314] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 27.225335] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 27.225422] NET: Registered protocol family 2
[ 27.268347] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 27.268667] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 27.269360] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 27.269704] TCP: Hash tables configured (established 131072 bind 65536)
[ 27.269745] TCP reno registered
[ 27.280398] checking if image is initramfs... it is
[ 27.651295] Freeing initrd memory: 4498k freed
[ 27.651962] audit: initializing netlink socket (disabled)
[ 27.652010] audit(1196014372.020:1): initialized
[ 27.652194] highmem bounce pool size: 64 pages
[ 27.653998] io scheduler noop registered
[ 27.654035] io scheduler anticipatory registered
[ 27.654072] io scheduler deadline registered
[ 27.654159] io scheduler cfq registered (default)
[ 27.654261] Boot video device is 0000:01:05.0
[ 27.654364] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 27.654380] assign_interrupt_mode Found MSI capability
[ 27.654418] Allocate Port Service[0000:00:04.0:pcie00]
[ 27.654449] Allocate Port Service[0000:00:04.0:pcie03]
[ 27.654499] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 27.654514] assign_interrupt_mode Found MSI capability
[ 27.654553] Allocate Port Service[0000:00:05.0:pcie00]
[ 27.654585] Allocate Port Service[0000:00:05.0:pcie03]
[ 27.654635] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 27.654649] assign_interrupt_mode Found MSI capability
[ 27.654688] Allocate Port Service[0000:00:06.0:pcie00]
[ 27.654719] Allocate Port Service[0000:00:06.0:pcie03]
[ 27.677129] Real Time Clock Driver v1.12ac
[ 27.677274] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 27.678313] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 27.678360] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 27.678399] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 27.678686] PNP: PS/2 Controller [PNP0303:C249,PNP0f13:C24A] at 0x60,0x64 irq 1,12
[ 27.680633] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 27.681441] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 27.681483] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 27.681522] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 27.681564] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 27.681605] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 27.681724] mice: PS/2 mouse device common for all mice
[ 27.681872] cpuidle: using governor ladder
[ 27.681910] cpuidle: using governor menu
[ 27.682016] TCP cubic registered
[ 27.682061] NET: Registered protocol family 1
[ 27.682117] Starting balanced_irq
[ 27.682171] Using IPI No-Shortcut mode
[ 27.682217] registered taskstats version 1
[ 27.682556] Freeing unused kernel memory: 220k freed
[ 27.705191] input: AT Translated Set 2 keyboard as /class/input/input0
[ 27.833398] fuse init (API version 7.9)
[ 27.836268] ACPI: Fan [C399] (off)
[ 27.836403] ACPI: Fan [C39A] (off)
[ 27.836529] ACPI: Fan [C39B] (off)
[ 27.836658] ACPI: Fan [C39C] (off)
[ 27.840819] ACPI: Processor [C000] (supports 8 throttling states)
[ 27.840938] ACPI: Processor [C001] (supports 8 throttling states)
[ 27.849623] ACPI: Thermal Zone [TZ1] (52 C)
[ 27.858144] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@xxxxxxxxxx
[ 28.323941] tg3.c:v3.86 (November 9, 2007)
[ 28.324049] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 28.324166] PCI: Setting latency timer of device 0000:10:00.0 to 64
[ 28.329849] SCSI subsystem initialized
[ 28.337076] usbcore: registered new interface driver usbfs
[ 28.337143] usbcore: registered new interface driver hub
[ 28.337521] usbcore: registered new device driver usb
[ 28.354467] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 28.360411] libata version 3.00 loaded.
[ 29.155875] eth0: Tigon3 [partno(none) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:1a:4b:61:68:b6
[ 29.156108] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 29.156150] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 29.157725] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 23 (level, low) -> IRQ 18
[ 29.157816] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 29.158048] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 29.158111] ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0601000
[ 29.216892] usb usb1: configuration #1 chosen from 1 choice
[ 29.216957] hub 1-0:1.0: USB hub found
[ 29.217000] hub 1-0:1.0: 2 ports detected
[ 29.320846] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 19
[ 29.320933] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 29.320999] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 29.321056] ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0602000
[ 29.380792] usb usb2: configuration #1 chosen from 1 choice
[ 29.380856] hub 2-0:1.0: USB hub found
[ 29.380899] hub 2-0:1.0: 2 ports detected
[ 29.484747] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 17 (level, low) -> IRQ 19
[ 29.484831] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 29.484888] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 29.484941] ohci_hcd 0000:00:13.2: irq 19, io mem 0xd0603000
[ 29.544705] usb usb3: configuration #1 chosen from 1 choice
[ 29.544771] hub 3-0:1.0: USB hub found
[ 29.544813] hub 3-0:1.0: 2 ports detected
[ 29.632586] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 29.648666] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 19
[ 29.648750] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 29.648806] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
[ 29.648864] ohci_hcd 0000:00:13.3: irq 19, io mem 0xd0604000
[ 29.708619] usb usb4: configuration #1 chosen from 1 choice
[ 29.708679] hub 4-0:1.0: USB hub found
[ 29.708721] hub 4-0:1.0: 2 ports detected
[ 29.812567] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 17 (level, low) -> IRQ 19
[ 29.812649] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 29.812706] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
[ 29.812758] ohci_hcd 0000:00:13.4: irq 19, io mem 0xd0605000
[ 29.860533] usb 1-2: configuration #1 chosen from 1 choice
[ 29.872534] usb usb5: configuration #1 chosen from 1 choice
[ 29.872593] hub 5-0:1.0: USB hub found
[ 29.872635] hub 5-0:1.0: 2 ports detected
[ 29.975350] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 23 (level, low) -> IRQ 18
[ 29.975439] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 29.975511] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
[ 29.975590] ehci_hcd 0000:00:13.5: debug port 1
[ 29.975635] ehci_hcd 0000:00:13.5: irq 18, io mem 0xd0606000
[ 29.975682] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 29.977227] usb 1-2: USB disconnect, address 2
[ 29.977149] usb usb6: configuration #1 chosen from 1 choice
[ 29.977227] hub 6-0:1.0: USB hub found
[ 29.977269] hub 6-0:1.0: 10 ports detected
[ 30.079049] SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot 0000:00:14.1
[ 30.079108] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
[ 30.079188] SB600_PATA: not 100% native mode: will probe irqs later
[ 30.079233] ide0: BM-DMA at 0x5040-0x5047, BIOS settings: hda:DMA, hdb:pio
[ 30.079344] Probing IDE interface ide0...
[ 30.811996] usb 1-2: new full speed USB device using ohci_hcd and address 3
[ 31.045887] usb 1-2: configuration #1 chosen from 1 choice
[ 31.486513] hda: TSSTcorpCD/DVDW TS-L632D, ATAPI CD/DVD-ROM drive
[ 31.486673] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 31.487224] hda: MW DMA 2 mode selected
[ 31.487673] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 31.512925] ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 21 (level, low) -> IRQ 20
[ 31.564831] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[d0101000-d01017ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 31.567456] ahci 0000:00:12.0: version 3.0
[ 31.567478] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 31.567567] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
[ 31.567605] ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP
[ 31.567644] ahci 0000:00:12.0: nr_ports (4) and implemented port map (0x1) don't match, using nr_ports
[ 31.567687] ahci 0000:00:12.0: forcing PORTS_IMPL to 0xf
[ 32.569674] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 32.569723] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum part
[ 32.570113] scsi0 : ahci
[ 32.570385] scsi1 : ahci
[ 32.570543] scsi2 : ahci
[ 32.571494] scsi3 : ahci
[ 32.571587] ata1: SATA max UDMA/133 abar m1024@0xd0609000 port 0xd0609100 irq 17
[ 32.571630] ata2: SATA max UDMA/133 abar m1024@0xd0609000 port 0xd0609180 irq 17
[ 32.571674] ata3: SATA max UDMA/133 abar m1024@0xd0609000 port 0xd0609200 irq 17
[ 32.571718] ata4: SATA max UDMA/133 abar m1024@0xd0609000 port 0xd0609280 irq 17
[ 32.839104] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f9929fd360e]
[ 33.046897] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.045929] ata1.00: ATA-7: TOSHIBA MK1637GSX, DL032C, max UDMA/100
[ 33.045972] ata1.00: 312581808 sectors, multi 16: LBA48
[ 33.048041] ata1.00: configured for UDMA/100
[ 33.358740] ata2: SATA link down (SStatus 0 SControl 0)
[ 33.670585] ata3: SATA link down (SStatus 0 SControl 0)
[ 33.982430] ata4: SATA link down (SStatus 0 SControl 0)
[ 33.981071] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1637GS DL03 PQ: 0 ANSI: 5
[ 33.998480] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 33.998533] sd 0:0:0:0: [sda] Write Protect is off
[ 33.998571] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 33.998584] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.998671] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 33.998719] sd 0:0:0:0: [sda] Write Protect is off
[ 33.998756] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 33.998768] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.998811] sda:<6>hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
[ 34.005351] Uniform CD-ROM driver Revision: 3.20
[ 34.063398] sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
[ 34.106759] sd 0:0:0:0: [sda] Attached SCSI disk
[ 34.108912] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 34.676046] Attempting manual resume
[ 34.688164] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 34.688984] SGI XFS Quota Management subsystem
[ 34.775235] XFS mounting filesystem sda7
[ 34.975307] Ending clean XFS mount for filesystem: sda7
[ 43.376260] Linux agpgart interface v0.102
[ 43.636018] ACPI: Battery Slot [C1ED] (battery present)
[ 43.636282] ACPI: Battery Slot [C1EC] (battery absent)
[ 43.644645] ACPI: AC Adapter [C1EB] (on-line)
[ 43.694218] input: Power Button (FF) as /class/input/input1
[ 43.745578] ACPI: Power Button (FF) [PWRF]
[ 43.745714] input: Sleep Button (CM) as /class/input/input2
[ 43.809545] ACPI: Sleep Button (CM) [C28D]
[ 43.809642] input: Lid Switch as /class/input/input3
[ 43.841635] ACPI: Lid Switch [C265]
[ 43.881231] input: Video Bus as /class/input/input4
[ 43.937596] ACPI: Video Device [C08D] (multi-head: yes rom: no post: no)
[ 44.487274] ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 21
[ 44.487359] PCI: Setting latency timer of device 0000:30:00.0 to 64
[ 44.526926] ssb: SPROM revision 3 detected.
[ 44.545198] ssb: Sonics Silicon Backplane found on PCI device 0000:30:00.0
[ 44.545270] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 44.557282] input: PC Speaker as /class/input/input5
[ 44.697815] Yenta: CardBus bridge found at 0000:02:04.0 [103c:30c2]
[ 44.734686] Bluetooth: Core ver 2.11
[ 44.735231] NET: Registered protocol family 31
[ 44.735269] Bluetooth: HCI device and connection manager initialized
[ 44.735309] Bluetooth: HCI socket layer initialized
[ 44.756837] hci_usb: Unknown symbol hci_suspend_dev
[ 44.756906] hci_usb: Unknown symbol hci_free_dev
[ 44.757243] hci_usb: Unknown symbol hci_resume_dev
[ 44.757341] hci_usb: Unknown symbol hci_alloc_dev
[ 44.757487] hci_usb: Unknown symbol hci_unregister_dev
[ 44.757591] hci_usb: Unknown symbol hci_recv_fragment
[ 44.757685] hci_usb: Unknown symbol hci_register_dev
[ 44.791380] Bluetooth: HCI USB driver ver 2.9
[ 44.793355] usbcore: registered new interface driver hci_usb
[ 44.825719] Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
[ 44.825763] Socket status: 30000006
[ 44.825800] Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 44.825847] pcmcia: parent PCI bridge Memory window: 0xd0100000 - 0xd03fffff
[ 44.943956] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
[ 45.221096] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x2580b1, caps: 0xa04793/0x300000
[ 45.221145] serio: Synaptics pass-through port at isa0060/serio4/input0
[ 45.261056] input: SynPS/2 Synaptics TouchPad as /class/input/input6
[ 45.864452] si3054: cannot initialize. EXT MID = 0000
[ 46.169816] Adding 1959888k swap on /dev/sda6. Priority:-1 extents:1 across:1959888k
[ 47.034313] kjournald starting. Commit interval 5 seconds
[ 47.036031] EXT3 FS on sda5, internal journal
[ 47.036037] EXT3-fs: mounted filesystem with ordered data mode.
[ 47.482189] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 47.491975] XFS mounting filesystem dm-0
[ 47.565937] Ending clean XFS mount for filesystem: dm-0
[ 47.605595] Filesystem "dm-4": Disabling barriers, not supported by the underlying device
[ 47.614285] XFS mounting filesystem dm-4
[ 47.672307] Ending clean XFS mount for filesystem: dm-4
[ 47.719837] Filesystem "dm-3": Disabling barriers, not supported by the underlying device
[ 47.720018] XFS mounting filesystem dm-3
[ 47.951644] Ending clean XFS mount for filesystem: dm-3
[ 47.991811] Filesystem "dm-1": Disabling barriers, not supported by the underlying device
[ 48.006627] XFS mounting filesystem dm-1
[ 48.117096] Ending clean XFS mount for filesystem: dm-1
[ 49.724522] No dock devices found.
[ 49.858478] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.20.00)
[ 49.860042] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x13
[ 49.860047] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x14
[ 49.860049] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x15
[ 49.860051] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e
[ 49.860094] powernow-k8: ph2 null fid transition 0xc
[ 51.003081] NET: Registered protocol family 10
[ 51.003293] lo: Disabled Privacy Extensions
[ 51.083479] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 58.303943] Clocksource tsc unstable (delta = -100023885 ns)
[ 60.646152] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 65.756020] b43-phy0: Broadcom 4311 WLAN found
[ 65.772223] b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 9
[ 65.772235] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 65.781839] b43-phy0 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config
[ 65.782751] phy0: Selected rate control algorithm 'simple'
[ 65.898377] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 66.359374] b43-phy0 debug: Chip initialized
[ 66.359467] b43-phy0 debug: 64-bit DMA initialized
[ 66.367521] b43-phy0 ERROR: PHY transmission error
[ 66.367557] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[ 66.367597] b43-phy0: Controller RESET (DMA error) ...
[ 66.367602] b43-phy0 debug: Wireless interface started
[ 66.367621] b43-phy0 debug: Wireless interface stopped
[ 66.367639] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 66.367664] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 66.412570] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 67.508775] b43-phy0 debug: Chip initialized
[ 67.508869] b43-phy0 debug: 64-bit DMA initialized
[ 67.529149] b43-phy0 debug: Wireless interface started
[ 67.529154] b43-phy0: Controller restarted
[ 67.529157] b43-phy0 debug: Adding Interface type 2
[ 67.530653] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[ 67.530735] b43-phy0: Controller RESET (DMA error) ...
[ 67.530722] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 67.576525] b43-phy0 debug: Wireless interface stopped
[ 67.576569] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 67.576606] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 67.689561] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 68.808150] b43-phy0 debug: Chip initialized
[ 68.808256] b43-phy0 debug: 64-bit DMA initialized
[ 68.828515] b43-phy0 debug: Wireless interface started
[ 68.828519] b43-phy0: Controller restarted
[ 68.829900] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[ 68.829981] b43-phy0: Controller RESET (DMA error) ...
[ 68.875876] b43-phy0 debug: Wireless interface stopped
[ 68.875901] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 68.875925] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 68.988878] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 70.107490] b43-phy0 debug: Chip initialized
[ 70.107582] b43-phy0 debug: 64-bit DMA initialized
[ 70.127862] b43-phy0 debug: Wireless interface started
[ 70.127866] b43-phy0: Controller restarted
[ 70.187227] b43-phy0 debug: Wireless interface stopped
[ 70.187250] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 70.187276] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 70.300230] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 71.444084] b43-phy0 debug: Chip initialized
[ 71.444408] b43-phy0 debug: 64-bit DMA initialized
[ 71.465992] printk: 2 messages suppressed.
[ 71.465997] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[ 71.466083] b43-phy0 debug: Wireless interface started
[ 71.466754] b43-phy0 debug: Wireless interface stopped
[ 71.466984] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 71.467226] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 71.576882] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 72.699479] b43-phy0 debug: Chip initialized
[ 72.699719] b43-phy0 debug: 64-bit DMA initialized
[ 72.721354] b43-phy0 debug: Wireless interface started
[ 72.731286] b43-phy0 debug: Wireless interface stopped
[ 72.731469] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 72.731677] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 72.844255] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 73.950862] b43-phy0 debug: Chip initialized
[ 73.951100] b43-phy0 debug: 64-bit DMA initialized
[ 73.972470] b43-phy0 debug: Wireless interface started
[ 73.972685] b43-phy0 debug: Wireless interface stopped
[ 73.972861] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 73.973069] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 74.083641] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 75.206225] b43-phy0 debug: Chip initialized
[ 75.206501] b43-phy0 debug: 64-bit DMA initialized
[ 75.227920] b43-phy0 debug: Wireless interface started
[ 75.238044] b43-phy0 debug: Wireless interface stopped
[ 75.238229] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 75.238438] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 75.351013] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 76.473611] b43-phy0 debug: Chip initialized
[ 76.473853] b43-phy0 debug: 64-bit DMA initialized
[ 76.495226] printk: 11 messages suppressed.
[ 76.495230] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[ 76.495317] b43-phy0 debug: Wireless interface started
[ 76.495890] b43-phy0 debug: Wireless interface stopped
[ 76.496067] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 76.496274] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 76.606393] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 77.724992] b43-phy0 debug: Chip initialized
[ 77.725230] b43-phy0 debug: 64-bit DMA initialized
[ 77.745393] b43-phy0 debug: Wireless interface started
[ 77.812708] b43-phy0 debug: Wireless interface stopped
[ 77.812882] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 77.813082] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 77.925728] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 79.052335] b43-phy0 debug: Chip initialized
[ 79.052549] b43-phy0 debug: 64-bit DMA initialized
[ 79.072691] b43-phy0 debug: Wireless interface started
[ 79.120059] b43-phy0 debug: Wireless interface stopped
[ 79.120225] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 79.120420] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 79.233092] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 80.353635] b43-phy0 debug: Chip initialized
[ 80.353758] b43-phy0 debug: 64-bit DMA initialized
[ 80.375580] b43-phy0 debug: Wireless interface started
[ 80.441369] b43-phy0 debug: Wireless interface stopped
[ 80.441405] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 80.441446] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 80.554412] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 81.665001] b43-phy0 debug: Chip initialized
[ 81.665117] b43-phy0 debug: 64-bit DMA initialized
[ 81.686879] b43-phy0 debug: Wireless interface started
[ 81.686889] printk: 11 messages suppressed.
[ 81.686890] b43-phy0: Controller restarted
[ 81.732732] b43-phy0 debug: Wireless interface stopped
[ 81.732769] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 81.732807] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 81.845741] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 82.960342] b43-phy0 debug: Chip initialized
[ 82.960459] b43-phy0 debug: 64-bit DMA initialized
[ 82.982244] b43-phy0 debug: Wireless interface started
[ 83.028088] b43-phy0 debug: Wireless interface stopped
[ 83.028124] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 83.028163] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 83.141133] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 84.263697] b43-phy0 debug: Chip initialized
[ 84.263813] b43-phy0 debug: 64-bit DMA initialized
[ 84.285594] b43-phy0 debug: Wireless interface started
[ 84.331442] b43-phy0 debug: Wireless interface stopped
[ 84.331477] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 84.331513] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 84.444486] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 85.571070] b43-phy0 debug: Chip initialized
[ 85.571186] b43-phy0 debug: 64-bit DMA initialized
[ 85.592944] b43-phy0 debug: Wireless interface started
[ 85.650789] b43-phy0 debug: Wireless interface stopped
[ 85.650823] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 85.650861] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 85.763834] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 86.894395] b43-phy0 debug: Chip initialized
[ 86.894511] b43-phy0 debug: 64-bit DMA initialized
[ 86.916299] b43-phy0 debug: Wireless interface started
[ 86.916308] printk: 11 messages suppressed.
[ 86.916310] b43-phy0: Controller restarted
[ 86.962140] b43-phy0 debug: Wireless interface stopped
[ 86.962174] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 86.962211] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 87.075186] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 88.193769] b43-phy0 debug: Chip initialized
[ 88.193884] b43-phy0 debug: 64-bit DMA initialized
[ 88.215643] b43-phy0 debug: Wireless interface started
[ 88.273491] b43-phy0 debug: Wireless interface stopped
[ 88.273525] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 88.273563] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 88.386536] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 89.509101] b43-phy0 debug: Chip initialized
[ 89.509219] b43-phy0 debug: 64-bit DMA initialized
[ 89.530982] b43-phy0 debug: Wireless interface started
[ 89.576845] b43-phy0 debug: Wireless interface stopped
[ 89.576878] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 89.576915] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128
[ 89.689891] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 90.804459] b43-phy0 debug: Chip initialized
[ 90.804573] b43-phy0 debug: 64-bit DMA initialized
[ 90.826538] b43-phy0 debug: Wireless interface started
[ 90.884198] b43-phy0 debug: Wireless interface stopped
[ 90.884233] b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 0/64
[ 90.884270] b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 0/128
[ 90.997245] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
