On Thu, 1 Nov 2007 17:56:40 -0400 Luis R. Rodriguez wrote:
> ** Resending after checkpatch.pl
>
> This adds documentation for struct ath5k_rate. This also removes
> some unused variables, lp_ack_duration and sp_ack_duration which
> are simply unnecessary. We obviously have information about the rest
> of the rate values, we can add more as we go, this just starts this up.
> I'll next target cleaning up the RATE macros, think that may be there
> the other G mode issues are in.
Thanks for doing this... but one more change, please:
(just move lines around, see below)
> Changes to ath5k.h
> Changes-licensed-under: ISC
>
> Signed-off-by: Luis R. Rodriguez <mcgrof@xxxxxxxxx>
> ---
> drivers/net/wireless/ath5k/ath5k.h | 58 +++++++++++++++++++++++++++++++----
> 1 files changed, 51 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/net/wireless/ath5k/ath5k.h b/drivers/net/wireless/ath5k/ath5k.h
> index c8ab09a..7147fb4 100644
> --- a/drivers/net/wireless/ath5k/ath5k.h
> +++ b/drivers/net/wireless/ath5k/ath5k.h
> @@ -549,17 +549,61 @@ struct ath5k_athchan_2ghz {
> * used by the rate control algorytm on MadWiFi.
> */
>
> -#define AR5K_MAX_RATES 32 /*max number of rates on the rate table*/
> +/* Max number of rates on the rate table and what it seems
> + * Atheros hardware supports */
> +#define AR5K_MAX_RATES 32
As described in Documentation/kernel-doc-nano-HOWTO.txt, the
structure fields/members should immediately follow the first line.
After all of the fields/members, you can add general info, like
the first paragraph that is here.
Example from that doc file:
/**
* struct my_struct - short description
* @a: first member
* @b: second member
*
* Longer description
*/
> +/**
> + * struct ath5k_rate - rate structure
> + *
> + * This structure is used to get the RX rate or set the TX rate on the
> + * hardware descriptors. It is also used for internal modulation control
> + * and settings.
> + *
> + * @valid: is this a valid rate for the current mode
> + * @modulation: respective mac80211 modulation
> + * @rate_kbps: rate in kbit/s
> + * @rate_code: hardware rate value, used in &struct ath5k_desc, on RX on
> + * &struct ath5k_rx_status.rs_rate and on TX on
> + * &struct ath5k_tx_status.ts_rate. Seems the ar5xxx harware supports
> + * up to 32 rates, indexed by 1-32. This means we really only need
> + * 6 bits for the rate_code.
> + * @dot11_rate: respective IEEE-802.11 rate value
> + * @control_rate: index of rate assumed to be used to send control frames.
> + * This can be used to set override the value on the rate duration
> + * registers. This is only useful if we can override in the harware at
> + * what rate we want to send control frames at. Note that IEEE-802.11
> + * Ch. 9.6 (after IEEE 802.11g changes) defines the rate at which we
> + * should send ACK/CTS, if we change this value we can be breaking
> + * the spec.
> + *
> + * On RX after the &struct ath5k_desc is parsed by the appropriate
> + * ah_proc_rx_desc() the respective hardware rate value is set in
> + * &struct ath5k_rx_status.rs_rate. On TX the desired rate is set in
> + * &struct ath5k_tx_status.ts_rate which is later used to setup the
> + * &struct ath5k_desc correctly. This is the hardware rate map we are
> + * aware of:
> + *
> + * rate_code 1 2 3 4 5 6 7 8
> + * rate_kbps 3000 ? ? ? ? ? ? ?
> + *
> + * rate_code 9 10 11 12 13 14 15 16
> + * rate_kbps ? ? ? ? ? ? ? ?
> + *
> + * rate_code 17 18 19 20 21 22 23 24
> + * rate_kbps ? ? ? ? ? ? ? ?
> + *
> + * rate_code 25 26 27 28 29 30 31 32
> + * rate_kbps ? ? ? ? ? ? ? ?
> + *
> + */
> struct ath5k_rate {
> - u8 valid; /* Valid for rate control */
> + u8 valid;
> u32 modulation;
> - u16 rate_kbps; /* Rate in kbps used in computetxtime */
> - u8 rate_code; /* Rate mapping for h/w descriptors */
> + u16 rate_kbps;
> + u8 rate_code;
> u8 dot11_rate;
> - u8 control_rate; /* Rate for management frames -not used */
> - u16 lp_ack_duration;/* long preamble ACK duration -not used */
> - u16 sp_ack_duration;/* short preamble ACK duration -not used */
> + u8 control_rate;
> };
>
> /* XXX: GRR all this stuff to get leds blinking ??? (check out setcurmode) */
> --
---
~Randy
-
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
