This patch adds a mac80211 based wireless driver for the rtl8185 PCI
wireless card.
Note that even though this driver is named rtl8180, it does not fully
support the rtl8180 yet. Andrea Merello will be doing the work for that
later. It supports the rtl8185 with the rtl8225z2 radio fairly well,
and the rtl8225 radio code should work too.
Thanks to Jukka Ruohonen for the donating a rtl8185 card! It was very
helpful for the rtl8225z2 code.
Signed-off-by: Michael Wu <flamingice@xxxxxxxxxxxx>
---
drivers/net/wireless/Kconfig | 5
drivers/net/wireless/Makefile | 3
drivers/net/wireless/rtl8180.h | 138 ++++
drivers/net/wireless/rtl8180_dev.c | 1013 ++++++++++++++++++++++++++++++++
drivers/net/wireless/rtl8180_rtl8225.c | 777 +++++++++++++++++++++++++
drivers/net/wireless/rtl8180_rtl8225.h | 28 +
drivers/net/wireless/rtl818x.h | 18 -
7 files changed, 1979 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index 4870bd5..421c577 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -546,6 +546,11 @@ config USB_ZD1201
To compile this driver as a module, choose M here: the
module will be called zd1201.
+config RTL8180
+ tristate "Realtek 8185 PCI support"
+ depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ select EEPROM_93CX6
+
config RTL8187
tristate "Realtek 8187 USB support"
depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile
index 8d4c366..3005eef 100644
--- a/drivers/net/wireless/Makefile
+++ b/drivers/net/wireless/Makefile
@@ -50,7 +50,10 @@ obj-$(CONFIG_PCMCIA_WL3501) += wl3501_cs.o
obj-$(CONFIG_USB_ZD1201) += zd1201.o
obj-$(CONFIG_LIBERTAS) += libertas/
+rtl8180-objs := rtl8180_dev.o rtl8180_rtl8225.o
rtl8187-objs := rtl8187_dev.o rtl8187_rtl8225.o
+
+obj-$(CONFIG_RTL8180) += rtl8180.o
obj-$(CONFIG_RTL8187) += rtl8187.o
obj-$(CONFIG_ADM8211) += adm8211.o
diff --git a/drivers/net/wireless/rtl8180.h b/drivers/net/wireless/rtl8180.h
new file mode 100644
index 0000000..4a5b44b
--- /dev/null
+++ b/drivers/net/wireless/rtl8180.h
@@ -0,0 +1,138 @@
+#ifndef RTL8180_H
+#define RTL8180_H
+
+#include "rtl818x.h"
+
+#define MAX_RX_SIZE IEEE80211_MAX_RTS_THRESHOLD
+
+#define RF_PARAM_DIGPHY (1 << 0)
+#define RF_PARAM_ANTBDEFAULT (1 << 1)
+#define RF_PARAM_CARRIERSENSE1 (1 << 2)
+#define RF_PARAM_CARRIERSENSE2 (1 << 3)
+
+enum rtl8180_tx_desc_flags {
+ RTL8180_TX_DESC_FLAG_NO_ENC = (1 << 15),
+ RTL8180_TX_DESC_FLAG_TX_OK = (1 << 15),
+ RTL8180_TX_DESC_FLAG_SPLCP = (1 << 16),
+ RTL8180_TX_DESC_FLAG_RX_UNDER = (1 << 16),
+ RTL8180_TX_DESC_FLAG_MOREFRAG = (1 << 17),
+ RTL8180_TX_DESC_FLAG_CTS = (1 << 18),
+ RTL8180_TX_DESC_FLAG_RTS = (1 << 23),
+ RTL8180_TX_DESC_FLAG_LS = (1 << 28),
+ RTL8180_TX_DESC_FLAG_FS = (1 << 29),
+ RTL8180_TX_DESC_FLAG_DMA = (1 << 30),
+ RTL8180_TX_DESC_FLAG_OWN = (1 << 31)
+};
+
+struct rtl8180_tx_desc {
+ __le32 flags;
+ __le16 rts_duration;
+ __le16 plcp_len;
+ __le32 tx_buf;
+ __le32 frame_len;
+ __le32 next_tx_desc;
+ u8 cw;
+ u8 retry_limit;
+ u8 agc;
+ u8 flags2;
+ u32 reserved[2];
+} __attribute__ ((packed));
+
+enum rtl8180_rx_desc_flags {
+ RTL8180_RX_DESC_FLAG_ICV_ERR = (1 << 12),
+ RTL8180_RX_DESC_FLAG_CRC32_ERR = (1 << 13),
+ RTL8180_RX_DESC_FLAG_PM = (1 << 14),
+ RTL8180_RX_DESC_FLAG_RX_ERR = (1 << 15),
+ RTL8180_RX_DESC_FLAG_BCAST = (1 << 16),
+ RTL8180_RX_DESC_FLAG_PAM = (1 << 17),
+ RTL8180_RX_DESC_FLAG_MCAST = (1 << 18),
+ RTL8180_RX_DESC_FLAG_SPLCP = (1 << 25),
+ RTL8180_RX_DESC_FLAG_FOF = (1 << 26),
+ RTL8180_RX_DESC_FLAG_DMA_FAIL = (1 << 27),
+ RTL8180_RX_DESC_FLAG_LS = (1 << 28),
+ RTL8180_RX_DESC_FLAG_FS = (1 << 29),
+ RTL8180_RX_DESC_FLAG_EOR = (1 << 30),
+ RTL8180_RX_DESC_FLAG_OWN = (1 << 31)
+};
+
+struct rtl8180_rx_desc {
+ __le32 flags;
+ __le32 flags2;
+ union {
+ __le32 rx_buf;
+ __le64 tsft;
+ };
+} __attribute__ ((packed));
+
+struct rtl8180_tx_ring {
+ struct rtl8180_tx_desc *desc;
+ dma_addr_t dma;
+ unsigned int idx;
+ unsigned int entries;
+ struct sk_buff_head queue;
+};
+
+struct rtl8180_priv {
+ /* common between rtl818x drivers */
+ struct rtl818x_csr __iomem *map;
+ void (*rf_init)(struct ieee80211_hw *);
+ void (*rf_stop)(struct ieee80211_hw *);
+ void (*rf_set_chan)(struct ieee80211_hw *, struct ieee80211_conf *);
+ int mode;
+ int if_id;
+
+ /* rtl8180 driver specific */
+ spinlock_t lock;
+ struct rtl8180_rx_desc *rx_ring;
+ dma_addr_t rx_ring_dma;
+ unsigned int rx_idx;
+ struct sk_buff *rx_buf[32];
+ struct rtl8180_tx_ring tx_ring[4];
+ struct ieee80211_channel channels[14];
+ struct ieee80211_rate rates[12];
+ struct ieee80211_hw_mode modes[2];
+ struct pci_dev *pdev;
+ u32 rx_conf;
+
+ int r8185;
+ u32 anaparam;
+ u16 rfparam;
+ u8 csthreshold;
+};
+
+void rtl8180_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data);
+
+static inline u8 rtl818x_ioread8(struct rtl8180_priv *priv, u8 __iomem *addr)
+{
+ return ioread8(addr);
+}
+
+static inline u16 rtl818x_ioread16(struct rtl8180_priv *priv, __le16 __iomem *addr)
+{
+ return ioread16(addr);
+}
+
+static inline u32 rtl818x_ioread32(struct rtl8180_priv *priv, __le32 __iomem *addr)
+{
+ return ioread32(addr);
+}
+
+static inline void rtl818x_iowrite8(struct rtl8180_priv *priv,
+ u8 __iomem *addr, u8 val)
+{
+ iowrite8(val, addr);
+}
+
+static inline void rtl818x_iowrite16(struct rtl8180_priv *priv,
+ __le16 __iomem *addr, u16 val)
+{
+ iowrite16(val, addr);
+}
+
+static inline void rtl818x_iowrite32(struct rtl8180_priv *priv,
+ __le32 __iomem *addr, u32 val)
+{
+ iowrite32(val, addr);
+}
+
+#endif /* RTL8180_H */
diff --git a/drivers/net/wireless/rtl8180_dev.c b/drivers/net/wireless/rtl8180_dev.c
new file mode 100644
index 0000000..5ec7ea9
--- /dev/null
+++ b/drivers/net/wireless/rtl8180_dev.c
@@ -0,0 +1,1013 @@
+
+/*
+ * Linux device driver for RTL8180 / RTL8185
+ *
+ * Copyright 2007 Michael Wu <flamingice@xxxxxxxxxxxx>
+ * Copyright 2007 Andrea Merello <andreamrl@xxxxxxxxxx>
+ *
+ * Based on the r8180 driver, which is:
+ * Copyright 2004-2005 Andrea Merello <andreamrl@xxxxxxxxxx>, et al.
+ *
+ * Thanks to Realtek for their support!
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/eeprom_93cx6.h>
+#include <net/mac80211.h>
+
+#include "rtl8180.h"
+#include "rtl8180_rtl8225.h"
+
+MODULE_AUTHOR("Michael Wu <flamingice@xxxxxxxxxxxx>");
+MODULE_AUTHOR("Andrea Merello <andreamrl@xxxxxxxxxx>");
+MODULE_DESCRIPTION("RTL8180 / RTL8185 PCI wireless driver");
+MODULE_LICENSE("GPL");
+
+static struct pci_device_id rtl8180_table[] __devinitdata = {
+ { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8185) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(pci, rtl8180_table);
+
+void rtl8180_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ int i = 10;
+ u32 buf;
+
+ buf = (data << 8) | addr;
+
+ rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf | 0x80);
+ while (i--) {
+ rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf);
+ if (rtl818x_ioread8(priv, &priv->map->PHY[2]) == (data & 0xFF))
+ return;
+ }
+}
+
+static void rtl8180_handle_rx(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ unsigned int count = 32;
+
+ while (count--) {
+ struct rtl8180_rx_desc *entry = &priv->rx_ring[priv->rx_idx];
+ struct sk_buff *skb = priv->rx_buf[priv->rx_idx];
+ u32 flags = le32_to_cpu(entry->flags);
+
+ if (flags & RTL8180_RX_DESC_FLAG_OWN)
+ return;
+
+ if (unlikely(flags & (RTL8180_RX_DESC_FLAG_DMA_FAIL |
+ RTL8180_RX_DESC_FLAG_FOF |
+ RTL8180_RX_DESC_FLAG_RX_ERR)))
+ goto done;
+ else {
+ u32 flags2 = le32_to_cpu(entry->flags2);
+ struct ieee80211_rx_status rx_status = {0};
+ struct sk_buff *new_skb = dev_alloc_skb(MAX_RX_SIZE);
+ int rate;
+
+ if (unlikely(!new_skb))
+ goto done;
+
+ pci_unmap_single(priv->pdev,
+ *((dma_addr_t *)skb->cb),
+ MAX_RX_SIZE, PCI_DMA_FROMDEVICE);
+ skb_put(skb, flags & 0xFFF);
+
+ rate = (flags >> 20) & 0xF;
+ rx_status.antenna = (flags2 >> 15) & 1;
+ /* TODO: improve signal/rssi reporting */
+ rx_status.signal = flags2 & 0xFF;
+ rx_status.ssi = (flags2 >> 8) & 0x7F;
+ rx_status.rate = priv->rates[rate].rate;
+ rx_status.freq = dev->conf.freq;
+ rx_status.channel = dev->conf.channel;
+ rx_status.phymode = dev->conf.phymode;
+ rx_status.mactime = le64_to_cpu(entry->tsft);
+ ieee80211_rx_irqsafe(dev, skb, &rx_status);
+
+ skb = new_skb;
+ priv->rx_buf[priv->rx_idx] = skb;
+ *((dma_addr_t *) skb->cb) =
+ pci_map_single(priv->pdev, skb_tail_pointer(skb),
+ MAX_RX_SIZE, PCI_DMA_FROMDEVICE);
+ }
+
+ done:
+ entry->rx_buf = cpu_to_le32(*((dma_addr_t *)skb->cb));
+ entry->flags = cpu_to_le32(RTL8180_RX_DESC_FLAG_OWN |
+ MAX_RX_SIZE);
+ if (priv->rx_idx == 31)
+ entry->flags |= cpu_to_le32(RTL8180_RX_DESC_FLAG_EOR);
+ priv->rx_idx = (priv->rx_idx + 1) % 32;
+ }
+}
+
+static void rtl8180_handle_tx(struct ieee80211_hw *dev, unsigned int prio)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ struct rtl8180_tx_ring *ring = &priv->tx_ring[prio];
+
+ while (skb_queue_len(&ring->queue)) {
+ struct rtl8180_tx_desc *entry = &ring->desc[ring->idx];
+ struct sk_buff *skb;
+ struct ieee80211_tx_status status = { {0} };
+ struct ieee80211_tx_control *control;
+ u32 flags = le32_to_cpu(entry->flags);
+
+ if (flags & RTL8180_TX_DESC_FLAG_OWN)
+ return;
+
+ ring->idx = (ring->idx + 1) % ring->entries;
+ skb = __skb_dequeue(&ring->queue);
+ pci_unmap_single(priv->pdev, le32_to_cpu(entry->tx_buf),
+ skb->len, PCI_DMA_TODEVICE);
+
+ control = *((struct ieee80211_tx_control **)skb->cb);
+ if (control)
+ memcpy(&status.control, control, sizeof(*control));
+ kfree(control);
+
+ if (!(status.control.flags & IEEE80211_TXCTL_NO_ACK)) {
+ if (flags & RTL8180_TX_DESC_FLAG_TX_OK)
+ status.flags = IEEE80211_TX_STATUS_ACK;
+ else
+ status.excessive_retries = 1;
+ }
+ status.retry_count = flags & 0xFF;
+
+ ieee80211_tx_status_irqsafe(dev, skb, &status);
+ if (ring->entries - skb_queue_len(&ring->queue) == 2)
+ ieee80211_wake_queue(dev, prio);
+ }
+}
+
+static irqreturn_t rtl8180_interrupt(int irq, void *dev_id)
+{
+ struct ieee80211_hw *dev = dev_id;
+ struct rtl8180_priv *priv = dev->priv;
+ u16 reg;
+
+ spin_lock(&priv->lock);
+ reg = rtl818x_ioread16(priv, &priv->map->INT_STATUS);
+ if (unlikely(reg == 0xFFFF)) {
+ spin_unlock(&priv->lock);
+ return IRQ_HANDLED;
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->INT_STATUS, reg);
+
+ if (reg & (RTL818X_INT_TXB_OK | RTL818X_INT_TXB_ERR))
+ rtl8180_handle_tx(dev, 3);
+
+ if (reg & (RTL818X_INT_TXH_OK | RTL818X_INT_TXH_ERR))
+ rtl8180_handle_tx(dev, 2);
+
+ if (reg & (RTL818X_INT_TXN_OK | RTL818X_INT_TXN_ERR))
+ rtl8180_handle_tx(dev, 1);
+
+ if (reg & (RTL818X_INT_TXL_OK | RTL818X_INT_TXL_ERR))
+ rtl8180_handle_tx(dev, 0);
+
+ if (reg & (RTL818X_INT_RX_OK | RTL818X_INT_RX_ERR))
+ rtl8180_handle_rx(dev);
+
+ spin_unlock(&priv->lock);
+
+ return IRQ_HANDLED;
+}
+
+static int rtl8180_tx(struct ieee80211_hw *dev, struct sk_buff *skb,
+ struct ieee80211_tx_control *control)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ struct rtl8180_tx_ring *ring;
+ struct rtl8180_tx_desc *entry;
+ unsigned long flags;
+ unsigned int idx, prio;
+ dma_addr_t mapping;
+ u32 tx_flags;
+
+ prio = control->queue;
+ ring = &priv->tx_ring[prio];
+
+ mapping = pci_map_single(priv->pdev, skb->data,
+ skb->len, PCI_DMA_TODEVICE);
+
+ tx_flags = RTL8180_TX_DESC_FLAG_OWN | RTL8180_TX_DESC_FLAG_FS |
+ RTL8180_TX_DESC_FLAG_LS | (control->tx_rate << 24) |
+ (control->rts_cts_rate << 19) | skb->len;
+
+ if (priv->r8185)
+ tx_flags |= RTL8180_TX_DESC_FLAG_DMA |
+ RTL8180_TX_DESC_FLAG_NO_ENC;
+
+ if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS)
+ tx_flags |= RTL8180_TX_DESC_FLAG_RTS;
+ else if (control->flags & IEEE80211_TXCTL_USE_CTS_PROTECT)
+ tx_flags |= RTL8180_TX_DESC_FLAG_CTS;
+
+ *((struct ieee80211_tx_control **) skb->cb) =
+ kmemdup(control, sizeof(*control), GFP_ATOMIC);
+
+ spin_lock_irqsave(&priv->lock, flags);
+ idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries;
+ entry = &ring->desc[idx];
+ /* TODO: calculate PLCP length - needed for rtl8180 */
+ if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS)
+ entry->rts_duration =
+ ieee80211_rts_duration(dev, priv->if_id, skb->len, control);
+ entry->tx_buf = cpu_to_le32(mapping);
+ entry->frame_len = cpu_to_le32(skb->len);
+ entry->flags2 = control->alt_retry_rate != -1 ?
+ control->alt_retry_rate << 4 : 0;
+ entry->retry_limit = control->retry_limit;
+ entry->flags = cpu_to_le32(tx_flags);
+ __skb_queue_tail(&ring->queue, skb);
+ if (ring->entries - skb_queue_len(&ring->queue) < 2)
+ ieee80211_stop_queue(dev, control->queue);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, (1 << (prio + 4)));
+
+ return 0;
+}
+
+static int rtl8180_init_hw(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u16 reg;
+
+ rtl818x_iowrite8(priv, &priv->map->CMD, 0);
+ rtl818x_ioread8(priv, &priv->map->CMD);
+ msleep(10);
+
+ /* reset */
+ rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
+ rtl818x_ioread8(priv, &priv->map->CMD);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CMD);
+ reg &= (1 << 1);
+ reg |= RTL818X_CMD_RESET;
+ rtl818x_iowrite8(priv, &priv->map->CMD, RTL818X_CMD_RESET);
+ rtl818x_ioread8(priv, &priv->map->CMD);
+ msleep(200);
+
+ /* check success of reset */
+ if (rtl818x_ioread8(priv, &priv->map->CMD) & RTL818X_CMD_RESET) {
+ printk(KERN_ERR "%s: reset timeout!\n", wiphy_name(dev->wiphy));
+ return -ETIMEDOUT;
+ }
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);
+ rtl818x_ioread8(priv, &priv->map->CMD);
+ msleep(200);
+
+ if (rtl818x_ioread8(priv, &priv->map->CONFIG3) & (1 << 3)) {
+ /* For cardbus */
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ reg |= 1 << 1;
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
+ reg = rtl818x_ioread16(priv, &priv->map->FEMR);
+ reg |= (1 << 15) | (1 << 14) | (1 << 4);
+ rtl818x_iowrite16(priv, &priv->map->FEMR, reg);
+ }
+
+ rtl818x_iowrite8(priv, &priv->map->MSR, 0);
+
+ if (!priv->r8185) {
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3,
+ reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, priv->anaparam);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3,
+ reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+ }
+
+ rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma);
+ rtl818x_iowrite32(priv, &priv->map->TBDA, priv->tx_ring[3].dma);
+ rtl818x_iowrite32(priv, &priv->map->THPDA, priv->tx_ring[2].dma);
+ rtl818x_iowrite32(priv, &priv->map->TNPDA, priv->tx_ring[1].dma);
+ rtl818x_iowrite32(priv, &priv->map->TLPDA, priv->tx_ring[0].dma);
+
+ /* TODO: necessary? specs indicate not */
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG2);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg & ~(1 << 3));
+ if (priv->r8185) {
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG2);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg | (1 << 4));
+ }
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ /* TODO: set CONFIG5 for calibrating AGC on rtl8180 + philips radio? */
+
+ /* TODO: turn off hw wep on rtl8180 */
+
+ rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
+
+ if (priv->r8185) {
+ rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
+ rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0x81);
+ rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
+ }
+
+ /* TODO: fix for rtl8180 */
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
+
+ if (priv->r8185) {
+ /* TODO: set ClkRun enable? necessary? */
+ reg = rtl818x_ioread8(priv, &priv->map->GP_ENABLE);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, reg & ~(1 << 6));
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | (1 << 2));
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+ }
+
+ priv->rf_init(dev);
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
+ return 0;
+}
+
+static int rtl8180_init_rx_ring(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ struct rtl8180_rx_desc *entry;
+ int i;
+
+ priv->rx_ring = pci_alloc_consistent(priv->pdev,
+ sizeof(*priv->rx_ring) * 32,
+ &priv->rx_ring_dma);
+
+ if (!priv->rx_ring || (unsigned long)priv->rx_ring & 0xFF) {
+ printk(KERN_ERR "%s: Cannot allocate RX ring\n",
+ wiphy_name(dev->wiphy));
+ return -ENOMEM;
+ }
+
+ memset(priv->rx_ring, 0, sizeof(*priv->rx_ring) * 32);
+ priv->rx_idx = 0;
+
+ for (i = 0; i < 32; i++) {
+ struct sk_buff *skb = dev_alloc_skb(MAX_RX_SIZE);
+ dma_addr_t *mapping;
+ entry = &priv->rx_ring[i];
+ if (!skb)
+ return 0;
+
+ priv->rx_buf[i] = skb;
+ mapping = (dma_addr_t *)skb->cb;
+ *mapping = pci_map_single(priv->pdev, skb_tail_pointer(skb),
+ MAX_RX_SIZE, PCI_DMA_FROMDEVICE);
+ entry->rx_buf = cpu_to_le32(*mapping);
+ entry->flags = cpu_to_le32(RTL8180_RX_DESC_FLAG_OWN |
+ MAX_RX_SIZE);
+ }
+ entry->flags |= cpu_to_le32(RTL8180_RX_DESC_FLAG_EOR);
+ return 0;
+}
+
+static void rtl8180_free_rx_ring(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ int i;
+
+ for (i = 0; i < 32; i++) {
+ struct sk_buff *skb = priv->rx_buf[i];
+ if (!skb)
+ continue;
+
+ pci_unmap_single(priv->pdev,
+ *((dma_addr_t *)skb->cb),
+ MAX_RX_SIZE, PCI_DMA_FROMDEVICE);
+ kfree_skb(skb);
+ }
+
+ pci_free_consistent(priv->pdev, sizeof(*priv->rx_ring) * 32,
+ priv->rx_ring, priv->rx_ring_dma);
+ priv->rx_ring = NULL;
+}
+
+static int rtl8180_init_tx_ring(struct ieee80211_hw *dev,
+ unsigned int prio, unsigned int entries)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ struct rtl8180_tx_desc *ring;
+ dma_addr_t dma;
+ int i;
+
+ ring = pci_alloc_consistent(priv->pdev, sizeof(*ring) * entries, &dma);
+ if (!ring || (unsigned long)ring & 0xFF) {
+ printk(KERN_ERR "%s: Cannot allocate TX ring (prio = %d)\n",
+ wiphy_name(dev->wiphy), prio);
+ return -ENOMEM;
+ }
+
+ memset(ring, 0, sizeof(*ring)*entries);
+ priv->tx_ring[prio].desc = ring;
+ priv->tx_ring[prio].dma = dma;
+ priv->tx_ring[prio].idx = 0;
+ priv->tx_ring[prio].entries = entries;
+ skb_queue_head_init(&priv->tx_ring[prio].queue);
+
+ for (i = 0; i < entries; i++)
+ ring[i].next_tx_desc =
+ cpu_to_le32((u32)dma + ((i + 1) % entries) * sizeof(*ring));
+
+ return 0;
+}
+
+static void rtl8180_free_tx_ring(struct ieee80211_hw *dev, unsigned int prio)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ struct rtl8180_tx_ring *ring = &priv->tx_ring[prio];
+
+ while (skb_queue_len(&ring->queue)) {
+ struct rtl8180_tx_desc *entry = &ring->desc[ring->idx];
+ struct sk_buff *skb = __skb_dequeue(&ring->queue);
+
+ pci_unmap_single(priv->pdev, le32_to_cpu(entry->tx_buf),
+ skb->len, PCI_DMA_TODEVICE);
+ kfree(*((struct ieee80211_tx_control **) skb->cb));
+ kfree_skb(skb);
+ ring->idx = (ring->idx + 1) % ring->entries;
+ }
+
+ pci_free_consistent(priv->pdev, sizeof(*ring->desc)*ring->entries,
+ ring->desc, ring->dma);
+ ring->desc = NULL;
+}
+
+static int rtl8180_start(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ int ret, i;
+ u32 reg;
+
+ ret = rtl8180_init_rx_ring(dev);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < 4; i++)
+ if ((ret = rtl8180_init_tx_ring(dev, i, 16)))
+ goto err_free_rings;
+
+ ret = rtl8180_init_hw(dev);
+ if (ret)
+ goto err_free_rings;
+
+ rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma);
+ rtl818x_iowrite32(priv, &priv->map->TBDA, priv->tx_ring[3].dma);
+ rtl818x_iowrite32(priv, &priv->map->THPDA, priv->tx_ring[2].dma);
+ rtl818x_iowrite32(priv, &priv->map->TNPDA, priv->tx_ring[1].dma);
+ rtl818x_iowrite32(priv, &priv->map->TLPDA, priv->tx_ring[0].dma);
+
+ ret = request_irq(priv->pdev->irq, &rtl8180_interrupt,
+ IRQF_SHARED, KBUILD_MODNAME, dev);
+ if (ret) {
+ printk(KERN_ERR "%s: failed to register IRQ handler\n",
+ wiphy_name(dev->wiphy));
+ goto err_free_rings;
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
+
+ reg = RTL818X_RX_CONF_ONLYERLPKT |
+ RTL818X_RX_CONF_RX_AUTORESETPHY |
+ RTL818X_RX_CONF_MGMT |
+ RTL818X_RX_CONF_DATA |
+ (7 << 8 /* MAX RX DMA */) |
+ RTL818X_RX_CONF_BROADCAST |
+ RTL818X_RX_CONF_MULTICAST |
+ RTL818X_RX_CONF_NICMAC;
+
+ if (priv->r8185)
+ reg |= RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2;
+ else {
+ reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE1)
+ ? RTL818X_RX_CONF_CSDM1 : 0;
+ reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE2)
+ ? RTL818X_RX_CONF_CSDM2 : 0;
+ }
+
+ priv->rx_conf = reg;
+ rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
+
+ if (priv->r8185) {
+ reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
+ reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT;
+ reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT;
+ rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
+
+ reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
+ reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT;
+ reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT;
+ reg |= RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
+ rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
+
+ /* disable early TX */
+ rtl818x_iowrite8(priv, (u8 __iomem *)priv->map + 0xec, 0x3f);
+ }
+
+ reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
+ reg |= (6 << 21 /* MAX TX DMA */) |
+ RTL818X_TX_CONF_NO_ICV;
+
+ if (priv->r8185)
+ reg &= ~RTL818X_TX_CONF_PROBE_DTS;
+ else
+ reg &= ~RTL818X_TX_CONF_HW_SEQNUM;
+
+ /* different meaning, same value on both rtl8185 and rtl8180 */
+ reg &= ~RTL818X_TX_CONF_SAT_HWPLCP;
+
+ rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CMD);
+ reg |= RTL818X_CMD_RX_ENABLE;
+ reg |= RTL818X_CMD_TX_ENABLE;
+ rtl818x_iowrite8(priv, &priv->map->CMD, reg);
+
+ priv->mode = IEEE80211_IF_TYPE_MNTR;
+ return 0;
+
+ err_free_rings:
+ rtl8180_free_rx_ring(dev);
+ for (i = 0; i < 4; i++)
+ if (priv->tx_ring[i].desc)
+ rtl8180_free_tx_ring(dev, i);
+
+ return ret;
+}
+
+static void rtl8180_stop(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u8 reg;
+ int i;
+
+ priv->mode = IEEE80211_IF_TYPE_INVALID;
+
+ rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CMD);
+ reg &= ~RTL818X_CMD_TX_ENABLE;
+ reg &= ~RTL818X_CMD_RX_ENABLE;
+ rtl818x_iowrite8(priv, &priv->map->CMD, reg);
+
+ priv->rf_stop(dev);
+
+ free_irq(priv->pdev->irq, dev);
+
+ rtl8180_free_rx_ring(dev);
+ for (i = 0; i < 4; i++)
+ rtl8180_free_tx_ring(dev, i);
+}
+
+static int rtl8180_add_interface(struct ieee80211_hw *dev,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct rtl8180_priv *priv = dev->priv;
+
+ if (priv->mode != IEEE80211_IF_TYPE_MNTR)
+ return -EOPNOTSUPP;
+
+ switch (conf->type) {
+ case IEEE80211_IF_TYPE_STA:
+ priv->mode = conf->type;
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->MAC[0],
+ cpu_to_le32(*(u32 *)conf->mac_addr));
+ rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->MAC[4],
+ cpu_to_le16(*(u16 *)(conf->mac_addr + 4)));
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ return 0;
+}
+
+static void rtl8180_remove_interface(struct ieee80211_hw *dev,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ priv->mode = IEEE80211_IF_TYPE_MNTR;
+}
+
+static int rtl8180_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf)
+{
+ struct rtl8180_priv *priv = dev->priv;
+
+ priv->rf_set_chan(dev, conf);
+
+ return 0;
+}
+
+static int rtl8180_config_interface(struct ieee80211_hw *dev, int if_id,
+ struct ieee80211_if_conf *conf)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ int i;
+
+ priv->if_id = if_id;
+
+ for (i = 0; i < ETH_ALEN; i++)
+ rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]);
+
+ if (is_valid_ether_addr(conf->bssid))
+ rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_INFRA);
+ else
+ rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_NO_LINK);
+
+ return 0;
+}
+
+static void rtl8180_configure_filter(struct ieee80211_hw *dev,
+ unsigned int changed_flags,
+ unsigned int *total_flags,
+ int mc_count, struct dev_addr_list *mc_list
+)
+{
+ struct rtl8180_priv *priv = dev->priv;
+
+ *total_flags = 0;
+
+ if (changed_flags & FIF_FCSFAIL)
+ priv->rx_conf ^= RTL818X_RX_CONF_FCS;
+ if (changed_flags & FIF_CONTROL)
+ priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
+ if (changed_flags & FIF_OTHER_BSS)
+ priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
+
+ /* TODO: Add proper multicast support */
+
+ if (priv->rx_conf & RTL818X_RX_CONF_FCS)
+ *total_flags |= FIF_FCSFAIL;
+ if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
+ *total_flags |= FIF_CONTROL;
+ if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
+ *total_flags |= FIF_OTHER_BSS;
+
+ rtl818x_iowrite32(priv, &priv->map->RX_CONF, priv->rx_conf);
+}
+
+static const struct ieee80211_ops rtl8180_ops = {
+ .tx = rtl8180_tx,
+ .start = rtl8180_start,
+ .stop = rtl8180_stop,
+ .add_interface = rtl8180_add_interface,
+ .remove_interface = rtl8180_remove_interface,
+ .config = rtl8180_config,
+ .config_interface = rtl8180_config_interface,
+ .configure_filter = rtl8180_configure_filter,
+};
+
+static void rtl8180_eeprom_register_read(struct eeprom_93cx6 *eeprom)
+{
+ struct ieee80211_hw *dev = eeprom->data;
+ struct rtl8180_priv *priv = dev->priv;
+ u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+
+ eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE;
+ eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ;
+ eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK;
+ eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS;
+}
+
+static void rtl8180_eeprom_register_write(struct eeprom_93cx6 *eeprom)
+{
+ struct ieee80211_hw *dev = eeprom->data;
+ struct rtl8180_priv *priv = dev->priv;
+ u8 reg = 2 << 6;
+
+ if (eeprom->reg_data_in)
+ reg |= RTL818X_EEPROM_CMD_WRITE;
+ if (eeprom->reg_data_out)
+ reg |= RTL818X_EEPROM_CMD_READ;
+ if (eeprom->reg_data_clock)
+ reg |= RTL818X_EEPROM_CMD_CK;
+ if (eeprom->reg_chip_select)
+ reg |= RTL818X_EEPROM_CMD_CS;
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(10);
+}
+
+static int __devinit rtl8180_probe(struct pci_dev *pdev,
+ const struct pci_device_id *id)
+{
+ struct ieee80211_hw *dev;
+ struct rtl8180_priv *priv;
+ unsigned long mem_addr, mem_len;
+ unsigned int io_addr, io_len;
+ int err, i;
+ struct eeprom_93cx6 eeprom;
+ const char *chip_name, *rf_name;
+ u32 reg;
+ u16 eeprom_val;
+
+ err = pci_enable_device(pdev);
+ if (err) {
+ printk(KERN_ERR "%s (rtl8180): Cannot enable new PCI device\n",
+ pci_name(pdev));
+ return err;
+ }
+
+ err = pci_request_regions(pdev, KBUILD_MODNAME);
+ if (err) {
+ printk(KERN_ERR "%s (rtl8180): Cannot obtain PCI resources\n",
+ pci_name(pdev));
+ return err;
+ }
+
+ io_addr = pci_resource_start(pdev, 0);
+ io_len = pci_resource_len(pdev, 0);
+ mem_addr = pci_resource_start(pdev, 1);
+ mem_len = pci_resource_len(pdev, 1);
+
+ if (mem_len < sizeof(struct rtl818x_csr) ||
+ io_len < sizeof(struct rtl818x_csr)) {
+ printk(KERN_ERR "%s (rtl8180): Too short PCI resources\n",
+ pci_name(pdev));
+ err = -ENOMEM;
+ goto err_free_reg;
+ }
+
+ if ((err = pci_set_dma_mask(pdev, 0xFFFFFF00ULL)) ||
+ (err = pci_set_consistent_dma_mask(pdev, 0xFFFFFF00ULL))) {
+ printk(KERN_ERR "%s (rtl8180): No suitable DMA available\n",
+ pci_name(pdev));
+ goto err_free_reg;
+ }
+
+ pci_set_master(pdev);
+
+ dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8180_ops);
+ if (!dev) {
+ printk(KERN_ERR "%s (rtl8180): ieee80211 alloc failed\n",
+ pci_name(pdev));
+ err = -ENOMEM;
+ goto err_free_reg;
+ }
+
+ priv = dev->priv;
+ priv->pdev = pdev;
+
+ SET_IEEE80211_DEV(dev, &pdev->dev);
+ pci_set_drvdata(pdev, dev);
+
+ priv->map = pci_iomap(pdev, 1, mem_len);
+ if (!priv->map)
+ priv->map = pci_iomap(pdev, 0, io_len);
+
+ if (!priv->map) {
+ printk(KERN_ERR "%s (rtl8180): Cannot map device memory\n",
+ pci_name(pdev));
+ goto err_free_dev;
+ }
+
+ memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
+ memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
+ priv->modes[0].mode = MODE_IEEE80211G;
+ priv->modes[0].num_rates = ARRAY_SIZE(rtl818x_rates);
+ priv->modes[0].rates = priv->rates;
+ priv->modes[0].num_channels = ARRAY_SIZE(rtl818x_channels);
+ priv->modes[0].channels = priv->channels;
+ priv->modes[1].mode = MODE_IEEE80211B;
+ priv->modes[1].num_rates = 4;
+ priv->modes[1].rates = priv->rates;
+ priv->modes[1].num_channels = ARRAY_SIZE(rtl818x_channels);
+ priv->modes[1].channels = priv->channels;
+ priv->mode = IEEE80211_IF_TYPE_INVALID;
+ dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
+ IEEE80211_HW_RX_INCLUDES_FCS;
+ dev->queues = 1;
+ dev->max_rssi = 65;
+
+ reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
+ reg &= RTL818X_TX_CONF_HWVER_MASK;
+ switch (reg) {
+ case RTL818X_TX_CONF_R8180_ABCD:
+ chip_name = "RTL8180";
+ break;
+ case RTL818X_TX_CONF_R8180_F:
+ chip_name = "RTL8180vF";
+ break;
+ case RTL818X_TX_CONF_R8185_ABC:
+ chip_name = "RTL8185";
+ break;
+ case RTL818X_TX_CONF_R8185_D:
+ chip_name = "RTL8185vD";
+ break;
+ default:
+ printk(KERN_ERR "%s (rtl8180): Unknown chip! (0x%x)\n",
+ pci_name(pdev), reg >> 25);
+ goto err_iounmap;
+ }
+
+ priv->r8185 = reg & RTL818X_TX_CONF_R8185_ABC;
+ if (priv->r8185) {
+ if ((err = ieee80211_register_hwmode(dev, &priv->modes[0])))
+ goto err_iounmap;
+
+ pci_set_mwi(pdev);
+ }
+
+ if ((err = ieee80211_register_hwmode(dev, &priv->modes[1])))
+ goto err_iounmap;
+
+ eeprom.data = dev;
+ eeprom.register_read = rtl8180_eeprom_register_read;
+ eeprom.register_write = rtl8180_eeprom_register_write;
+ if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6))
+ eeprom.width = PCI_EEPROM_WIDTH_93C66;
+ else
+ eeprom.width = PCI_EEPROM_WIDTH_93C46;
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_PROGRAM);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(10);
+
+ eeprom_93cx6_read(&eeprom, 0x06, &eeprom_val);
+ eeprom_val &= 0xFF;
+ switch (eeprom_val) {
+ case 1:
+ rf_name = "Intersil";
+ break;
+ case 2:
+ rf_name = "RFMD";
+ break;
+ case 3:
+ rf_name = "Philips";
+ break;
+ case 4:
+ rf_name = "Maxim";
+ break;
+ case 5:
+ rf_name = "GCT";
+ break;
+ case 9:
+ if (rtl8225_is_z2(dev)) {
+ rf_name = "RTL8225z2";
+ priv->rf_init = rtl8225z2_rf_init;
+ } else {
+ rf_name = "RTL8225";
+ priv->rf_init = rtl8225_rf_init;
+ }
+ priv->rf_stop = rtl8225_rf_stop;
+ priv->rf_set_chan = rtl8225_rf_set_channel;
+ break;
+ case 10:
+ rf_name = "RTL8255";
+ break;
+ default:
+ printk(KERN_ERR "%s (rtl8180): Unknown RF! (0x%x)\n",
+ pci_name(pdev), eeprom_val);
+ goto err_iounmap;
+ }
+
+ if (eeprom_val < 3) {
+ printk(KERN_ERR "%s (rtl8180): %s RF frontend not supported!\n",
+ pci_name(pdev), rf_name);
+ goto err_iounmap;
+ }
+
+ eeprom_93cx6_read(&eeprom, 0x19, &priv->rfparam);
+ eeprom_93cx6_read(&eeprom, 0x17, &eeprom_val);
+ priv->csthreshold = eeprom_val >> 8;
+ if (!priv->r8185) {
+ __le32 anaparam;
+ eeprom_93cx6_multiread(&eeprom, 0xD, (__le16 *)&anaparam, 2);
+ priv->anaparam = le32_to_cpu(anaparam);
+ }
+
+ eeprom_93cx6_multiread(&eeprom, 0x7, (__le16 *)dev->wiphy->perm_addr, 3);
+ if (!is_valid_ether_addr(dev->wiphy->perm_addr)) {
+ printk(KERN_WARNING "%s (rtl8180): Invalid hwaddr! Using"
+ " randomly generated MAC addr\n", pci_name(pdev));
+ random_ether_addr(dev->wiphy->perm_addr);
+ }
+
+ /* CCK TX power */
+ for (i = 0; i < 14; i += 2) {
+ u16 txpwr;
+ eeprom_93cx6_read(&eeprom, 0x10 + (i >> 1), &txpwr);
+ priv->channels[i].val = txpwr & 0xFF;
+ priv->channels[i + 1].val = txpwr >> 8;
+ }
+
+ /* OFDM TX power */
+ if (priv->r8185) {
+ for (i = 0; i < 14; i += 2) {
+ u16 txpwr;
+ eeprom_93cx6_read(&eeprom, 0x20 + (i >> 1), &txpwr);
+ priv->channels[i].val |= (txpwr & 0xFF) << 8;
+ priv->channels[i + 1].val |= txpwr & 0xFF00;
+ }
+ }
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ spin_lock_init(&priv->lock);
+
+ err = ieee80211_register_hw(dev);
+ if (err) {
+ printk(KERN_ERR "%s (rtl8180): Cannot register device\n",
+ pci_name(pdev));
+ goto err_iounmap;
+ }
+
+ printk(KERN_INFO "%s: hwaddr " MAC_FMT ", %s + %s\n",
+ wiphy_name(dev->wiphy), MAC_ARG(dev->wiphy->perm_addr),
+ chip_name, rf_name);
+
+ return 0;
+
+ err_iounmap:
+ iounmap(priv->map);
+
+ err_free_dev:
+ pci_set_drvdata(pdev, NULL);
+ ieee80211_free_hw(dev);
+
+ err_free_reg:
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ return err;
+}
+
+static void __devexit rtl8180_remove(struct pci_dev *pdev)
+{
+ struct ieee80211_hw *dev = pci_get_drvdata(pdev);
+ struct rtl8180_priv *priv;
+
+ if (!dev)
+ return;
+
+ ieee80211_unregister_hw(dev);
+
+ priv = dev->priv;
+
+ pci_iounmap(pdev, priv->map);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ ieee80211_free_hw(dev);
+}
+
+#ifdef CONFIG_PM
+static int rtl8180_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ pci_save_state(pdev);
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ return 0;
+}
+
+static int rtl8180_resume(struct pci_dev *pdev)
+{
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ return 0;
+}
+
+#endif /* CONFIG_PM */
+
+static struct pci_driver rtl8180_driver = {
+ .name = KBUILD_MODNAME,
+ .id_table = rtl8180_table,
+ .probe = rtl8180_probe,
+ .remove = __devexit_p(rtl8180_remove),
+#ifdef CONFIG_PM
+ .suspend = rtl8180_suspend,
+ .resume = rtl8180_resume,
+#endif /* CONFIG_PM */
+};
+
+static int __init rtl8180_init(void)
+{
+ return pci_register_driver(&rtl8180_driver);
+}
+
+static void __exit rtl8180_exit(void)
+{
+ pci_unregister_driver(&rtl8180_driver);
+}
+
+module_init(rtl8180_init);
+module_exit(rtl8180_exit);
diff --git a/drivers/net/wireless/rtl8180_rtl8225.c b/drivers/net/wireless/rtl8180_rtl8225.c
new file mode 100644
index 0000000..96b9b7f
--- /dev/null
+++ b/drivers/net/wireless/rtl8180_rtl8225.c
@@ -0,0 +1,777 @@
+
+/*
+ * Radio tuning for RTL8225 on RTL8180
+ *
+ * Copyright 2007 Michael Wu <flamingice@xxxxxxxxxxxx>
+ * Copyright 2007 Andrea Merello <andreamrl@xxxxxxxxxx>
+ *
+ * Based on the r8180 driver, which is:
+ * Copyright 2005 Andrea Merello <andreamrl@xxxxxxxxxx>, et al.
+ *
+ * Thanks to Realtek for their support!
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <net/mac80211.h>
+
+#include "rtl8180.h"
+#include "rtl8180_rtl8225.h"
+
+static void rtl8225_write(struct ieee80211_hw *dev, u8 addr, u16 data)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u16 reg80, reg84, reg82;
+ u32 bangdata;
+ int i;
+
+ bangdata = (data << 4) | (addr & 0xf);
+
+ reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput) & 0xfff3;
+ reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x7);
+
+ reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x7 | 0x400);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(10);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(10);
+
+ for (i = 15; i >= 0; i--) {
+ u16 reg = reg80 | !!(bangdata & (1 << i));
+
+ if (i & 1)
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1));
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1));
+
+ if (!(i & 1))
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(10);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x400);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+}
+
+static u16 rtl8225_read(struct ieee80211_hw *dev, u8 addr)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u16 reg80, reg82, reg84, out;
+ int i;
+
+ reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput);
+ reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable);
+ reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect) | 0x400;
+
+ reg80 &= ~0xF;
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x000F);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x000F);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(4);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(5);
+
+ for (i = 4; i >= 0; i--) {
+ u16 reg = reg80 | ((addr >> i) & 1);
+
+ if (!(i & 1)) {
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(1);
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg | (1 << 1));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg | (1 << 1));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+
+ if (i & 1) {
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(1);
+ }
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x000E);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x040E);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+
+ out = 0;
+ for (i = 11; i >= 0; i--) {
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(1);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+
+ if (rtl818x_ioread16(priv, &priv->map->RFPinsInput) & (1 << 1))
+ out |= 1 << i;
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 2));
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ udelay(2);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x03A0);
+
+ return out;
+}
+
+static const u16 rtl8225bcd_rxgain[] = {
+ 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409,
+ 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541,
+ 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583,
+ 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644,
+ 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688,
+ 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745,
+ 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789,
+ 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793,
+ 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d,
+ 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9,
+ 0x07aa, 0x07ab, 0x07ac, 0x07ad, 0x07b0, 0x07b1, 0x07b2, 0x07b3,
+ 0x07b4, 0x07b5, 0x07b8, 0x07b9, 0x07ba, 0x07bb, 0x07bb
+};
+
+static const u8 rtl8225_agc[] = {
+ 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e,
+ 0x9d, 0x9c, 0x9b, 0x9a, 0x99, 0x98, 0x97, 0x96,
+ 0x95, 0x94, 0x93, 0x92, 0x91, 0x90, 0x8f, 0x8e,
+ 0x8d, 0x8c, 0x8b, 0x8a, 0x89, 0x88, 0x87, 0x86,
+ 0x85, 0x84, 0x83, 0x82, 0x81, 0x80, 0x3f, 0x3e,
+ 0x3d, 0x3c, 0x3b, 0x3a, 0x39, 0x38, 0x37, 0x36,
+ 0x35, 0x34, 0x33, 0x32, 0x31, 0x30, 0x2f, 0x2e,
+ 0x2d, 0x2c, 0x2b, 0x2a, 0x29, 0x28, 0x27, 0x26,
+ 0x25, 0x24, 0x23, 0x22, 0x21, 0x20, 0x1f, 0x1e,
+ 0x1d, 0x1c, 0x1b, 0x1a, 0x19, 0x18, 0x17, 0x16,
+ 0x15, 0x14, 0x13, 0x12, 0x11, 0x10, 0x0f, 0x0e,
+ 0x0d, 0x0c, 0x0b, 0x0a, 0x09, 0x08, 0x07, 0x06,
+ 0x05, 0x04, 0x03, 0x02, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01
+};
+
+static const u8 rtl8225_gain[] = {
+ 0x23, 0x88, 0x7c, 0xa5, /* -82dbm */
+ 0x23, 0x88, 0x7c, 0xb5, /* -82dbm */
+ 0x23, 0x88, 0x7c, 0xc5, /* -82dbm */
+ 0x33, 0x80, 0x79, 0xc5, /* -78dbm */
+ 0x43, 0x78, 0x76, 0xc5, /* -74dbm */
+ 0x53, 0x60, 0x73, 0xc5, /* -70dbm */
+ 0x63, 0x58, 0x70, 0xc5, /* -66dbm */
+};
+
+static const u8 rtl8225_threshold[] = {
+ 0x8d, 0x8d, 0x8d, 0x8d, 0x9d, 0xad, 0xbd
+};
+
+static const u8 rtl8225_tx_gain_cck_ofdm[] = {
+ 0x02, 0x06, 0x0e, 0x1e, 0x3e, 0x7e
+};
+
+static const u8 rtl8225_tx_power_cck[] = {
+ 0x18, 0x17, 0x15, 0x11, 0x0c, 0x08, 0x04, 0x02,
+ 0x1b, 0x1a, 0x17, 0x13, 0x0e, 0x09, 0x04, 0x02,
+ 0x1f, 0x1e, 0x1a, 0x15, 0x10, 0x0a, 0x05, 0x02,
+ 0x22, 0x21, 0x1d, 0x18, 0x11, 0x0b, 0x06, 0x02,
+ 0x26, 0x25, 0x21, 0x1b, 0x14, 0x0d, 0x06, 0x03,
+ 0x2b, 0x2a, 0x25, 0x1e, 0x16, 0x0e, 0x07, 0x03
+};
+
+static const u8 rtl8225_tx_power_cck_ch14[] = {
+ 0x18, 0x17, 0x15, 0x0c, 0x00, 0x00, 0x00, 0x00,
+ 0x1b, 0x1a, 0x17, 0x0e, 0x00, 0x00, 0x00, 0x00,
+ 0x1f, 0x1e, 0x1a, 0x0f, 0x00, 0x00, 0x00, 0x00,
+ 0x22, 0x21, 0x1d, 0x11, 0x00, 0x00, 0x00, 0x00,
+ 0x26, 0x25, 0x21, 0x13, 0x00, 0x00, 0x00, 0x00,
+ 0x2b, 0x2a, 0x25, 0x15, 0x00, 0x00, 0x00, 0x00
+};
+
+static const u8 rtl8225_tx_power_ofdm[] = {
+ 0x80, 0x90, 0xa2, 0xb5, 0xcb, 0xe4
+};
+
+static const u32 rtl8225_chan[] = {
+ 0x085c, 0x08dc, 0x095c, 0x09dc, 0x0a5c, 0x0adc, 0x0b5c,
+ 0x0bdc, 0x0c5c, 0x0cdc, 0x0d5c, 0x0ddc, 0x0e5c, 0x0f72
+};
+
+static void rtl8225_rf_set_tx_power(struct ieee80211_hw *dev, int channel)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u8 cck_power, ofdm_power;
+ const u8 *tmp;
+ u32 reg;
+ int i;
+
+ cck_power = priv->channels[channel - 1].val & 0xF;
+ ofdm_power = priv->channels[channel - 1].val >> 4;
+
+ cck_power = min(cck_power, (u8)35);
+ ofdm_power = min(ofdm_power, (u8)35);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK,
+ rtl8225_tx_gain_cck_ofdm[cck_power / 6] >> 1);
+
+ if (channel == 14)
+ tmp = &rtl8225_tx_power_cck_ch14[(cck_power % 6) * 8];
+ else
+ tmp = &rtl8225_tx_power_cck[(cck_power % 6) * 8];
+
+ for (i = 0; i < 8; i++)
+ rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++);
+
+ msleep(1); /* FIXME: optional? */
+
+ /* anaparam2 on */
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl8225_write_phy_ofdm(dev, 2, 0x42);
+ rtl8225_write_phy_ofdm(dev, 6, 0x00);
+ rtl8225_write_phy_ofdm(dev, 8, 0x00);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM,
+ rtl8225_tx_gain_cck_ofdm[ofdm_power/6] >> 1);
+
+ tmp = &rtl8225_tx_power_ofdm[ofdm_power % 6];
+
+ rtl8225_write_phy_ofdm(dev, 5, *tmp);
+ rtl8225_write_phy_ofdm(dev, 7, *tmp);
+
+ msleep(1);
+}
+
+int rtl8225_is_z2(struct ieee80211_hw *dev)
+{
+ int z2 = 0;
+
+ rtl8225_write(dev, 0, 0x1B7);
+ rtl8225_read(dev, 0);
+
+ if (rtl8225_read(dev, 8) == 0x588 && rtl8225_read(dev, 9) == 0x700)
+ z2 = 1;
+
+ rtl8225_write(dev, 0, 0x0B7);
+
+ return z2;
+}
+
+void rtl8225_rf_init(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ int i;
+ u8 reg;
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ /* host_pci_init */
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x0488);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ msleep(200); /* FIXME: ehh?? */
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0xFF & ~(1 << 6));
+
+ rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008);
+
+ /* TODO: check if we need really to change BRSR to do RF config */
+ rtl818x_ioread16(priv, &priv->map->BRSR);
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
+ rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl8225_write(dev, 0x0, 0x067);
+ rtl8225_write(dev, 0x1, 0xFE0);
+ rtl8225_write(dev, 0x2, 0x44D);
+ rtl8225_write(dev, 0x3, 0x441);
+ rtl8225_write(dev, 0x4, 0x8BE);
+ rtl8225_write(dev, 0x5, 0xBF0); /* TODO: minipci */
+ rtl8225_write(dev, 0x6, 0xAE6);
+ rtl8225_write(dev, 0x7, rtl8225_chan[0]);
+ rtl8225_write(dev, 0x8, 0x01F);
+ rtl8225_write(dev, 0x9, 0x334);
+ rtl8225_write(dev, 0xA, 0xFD4);
+ rtl8225_write(dev, 0xB, 0x391);
+ rtl8225_write(dev, 0xC, 0x050);
+ rtl8225_write(dev, 0xD, 0x6DB);
+ rtl8225_write(dev, 0xE, 0x029);
+ rtl8225_write(dev, 0xF, 0x914); msleep(1);
+
+ rtl8225_write(dev, 0x2, 0xC4D); msleep(100);
+
+ rtl8225_write(dev, 0x0, 0x127);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225bcd_rxgain); i++) {
+ rtl8225_write(dev, 0x1, i + 1);
+ rtl8225_write(dev, 0x2, rtl8225bcd_rxgain[i]);
+ }
+
+ rtl8225_write(dev, 0x0, 0x027);
+ rtl8225_write(dev, 0x0, 0x22F);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) {
+ rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]);
+ msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i);
+ msleep(1);
+ }
+
+ msleep(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x00, 0x01); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x01, 0x02); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x02, 0x62); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x03, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x04, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x05, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x06, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x07, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x08, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0a, 0x09); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x10, 0x84); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x11, 0x06); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x12, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x13, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x14, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x15, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x16, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x17, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x19, 0x19); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1b, 0x76); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x21, 0x27); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x22, 0x16); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x24, 0x46); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x25, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x27, 0x88); msleep(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[1 * 4]);
+ rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[1 * 4 + 2]);
+ rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[1 * 4 + 3]);
+ rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[1 * 4 + 1]);
+
+ rtl8225_write_phy_cck(dev, 0x00, 0x98); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x03, 0x20); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x04, 0x7e); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x05, 0x12); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x06, 0xfc); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x07, 0x78); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x08, 0x2e); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x10, 0x93); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x11, 0x88); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x12, 0x47); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x13, 0xd0);
+ rtl8225_write_phy_cck(dev, 0x19, 0x00);
+ rtl8225_write_phy_cck(dev, 0x1a, 0xa0);
+ rtl8225_write_phy_cck(dev, 0x1b, 0x08);
+ rtl8225_write_phy_cck(dev, 0x40, 0x86);
+ rtl8225_write_phy_cck(dev, 0x41, 0x8d); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x42, 0x15); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x43, 0x18); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x44, 0x1f); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x45, 0x1e); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x46, 0x1a); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x47, 0x15); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x48, 0x10); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x49, 0x0a); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x4a, 0x05); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x4b, 0x02); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x4c, 0x05); msleep(1);
+
+ rtl818x_iowrite8(priv, &priv->map->TESTR, 0x0D); msleep(1);
+
+ rtl8225_rf_set_tx_power(dev, 1);
+
+ /* RX antenna default to A */
+ rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); /* B: 0xDB */
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); /* B: 0x10 */
+
+ rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */
+ msleep(1);
+ rtl818x_iowrite32(priv, (__le32 __iomem *)((void __iomem *)priv->map + 0x94), 0x15c00002);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+
+ /* set sensitivity */
+ rtl8225_write(dev, 0x0c, 0x50);
+ rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[1 * 4]);
+ rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[1 * 4 + 2]);
+ rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[1 * 4 + 3]);
+ rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[1 * 4 + 1]);
+ rtl8225_write_phy_cck(dev, 0x41, rtl8225_threshold[2]);
+}
+
+static const u8 rtl8225z2_tx_power_cck_ch14[] = {
+ 0x36, 0x35, 0x2e, 0x1b, 0x00, 0x00, 0x00, 0x00
+};
+
+static const u8 rtl8225z2_tx_power_cck_B[] = {
+ 0x30, 0x2f, 0x29, 0x21, 0x19, 0x10, 0x08, 0x04
+};
+
+static const u8 rtl8225z2_tx_power_cck_A[] = {
+ 0x33, 0x32, 0x2b, 0x23, 0x1a, 0x11, 0x08, 0x04
+};
+
+static const u8 rtl8225z2_tx_power_cck[] = {
+ 0x36, 0x35, 0x2e, 0x25, 0x1c, 0x12, 0x09, 0x04
+};
+
+static void rtl8225z2_rf_set_tx_power(struct ieee80211_hw *dev, int channel)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u8 cck_power, ofdm_power;
+ const u8 *tmp;
+ int i;
+
+ cck_power = priv->channels[channel - 1].val & 0xF;
+ ofdm_power = priv->channels[channel - 1].val >> 4;
+
+ if (channel == 14)
+ tmp = rtl8225z2_tx_power_cck_ch14;
+ else if (cck_power == 12)
+ tmp = rtl8225z2_tx_power_cck_B;
+ else if (cck_power == 13)
+ tmp = rtl8225z2_tx_power_cck_A;
+ else
+ tmp = rtl8225z2_tx_power_cck;
+
+ for (i = 0; i < 8; i++)
+ rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++);
+
+ cck_power = min(cck_power, (u8)35);
+ if (cck_power == 13 || cck_power == 14)
+ cck_power = 12;
+ if (cck_power >= 15)
+ cck_power -= 2;
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK, cck_power);
+ rtl818x_ioread8(priv, &priv->map->TX_GAIN_CCK);
+ msleep(1);
+
+ ofdm_power = min(ofdm_power, (u8)35);
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM, ofdm_power);
+
+ rtl8225_write_phy_ofdm(dev, 2, 0x42);
+ rtl8225_write_phy_ofdm(dev, 5, 0x00);
+ rtl8225_write_phy_ofdm(dev, 6, 0x40);
+ rtl8225_write_phy_ofdm(dev, 7, 0x00);
+ rtl8225_write_phy_ofdm(dev, 8, 0x40);
+
+ msleep(1);
+}
+
+static const u16 rtl8225z2_rxgain[] = {
+ 0x0000, 0x0001, 0x0002, 0x0003, 0x0004, 0x0005, 0x0008, 0x0009,
+ 0x000a, 0x000b, 0x0102, 0x0103, 0x0104, 0x0105, 0x0140, 0x0141,
+ 0x0142, 0x0143, 0x0144, 0x0145, 0x0180, 0x0181, 0x0182, 0x0183,
+ 0x0184, 0x0185, 0x0188, 0x0189, 0x018a, 0x018b, 0x0243, 0x0244,
+ 0x0245, 0x0280, 0x0281, 0x0282, 0x0283, 0x0284, 0x0285, 0x0288,
+ 0x0289, 0x028a, 0x028b, 0x028c, 0x0342, 0x0343, 0x0344, 0x0345,
+ 0x0380, 0x0381, 0x0382, 0x0383, 0x0384, 0x0385, 0x0388, 0x0389,
+ 0x038a, 0x038b, 0x038c, 0x038d, 0x0390, 0x0391, 0x0392, 0x0393,
+ 0x0394, 0x0395, 0x0398, 0x0399, 0x039a, 0x039b, 0x039c, 0x039d,
+ 0x03a0, 0x03a1, 0x03a2, 0x03a3, 0x03a4, 0x03a5, 0x03a8, 0x03a9,
+ 0x03aa, 0x03ab, 0x03ac, 0x03ad, 0x03b0, 0x03b1, 0x03b2, 0x03b3,
+ 0x03b4, 0x03b5, 0x03b8, 0x03b9, 0x03ba, 0x03bb, 0x03bb
+};
+
+void rtl8225z2_rf_init(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ int i;
+ u8 reg;
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ /* host_pci_init */
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x0488);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
+ rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+ msleep(200); /* FIXME: ehh?? */
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0xFF & ~(1 << 6));
+
+ rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00088008);
+
+ /* TODO: check if we need really to change BRSR to do RF config */
+ rtl818x_ioread16(priv, &priv->map->BRSR);
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
+ rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+
+ rtl8225_write(dev, 0x0, 0x0B7); msleep(1);
+ rtl8225_write(dev, 0x1, 0xEE0); msleep(1);
+ rtl8225_write(dev, 0x2, 0x44D); msleep(1);
+ rtl8225_write(dev, 0x3, 0x441); msleep(1);
+ rtl8225_write(dev, 0x4, 0x8C3); msleep(1);
+ rtl8225_write(dev, 0x5, 0xC72); msleep(1);
+ rtl8225_write(dev, 0x6, 0x0E6); msleep(1);
+ rtl8225_write(dev, 0x7, 0x82A); msleep(1);
+ rtl8225_write(dev, 0x8, 0x03F); msleep(1);
+ rtl8225_write(dev, 0x9, 0x335); msleep(1);
+ rtl8225_write(dev, 0xa, 0x9D4); msleep(1);
+ rtl8225_write(dev, 0xb, 0x7BB); msleep(1);
+ rtl8225_write(dev, 0xc, 0x850); msleep(1);
+ rtl8225_write(dev, 0xd, 0xCDF); msleep(1);
+ rtl8225_write(dev, 0xe, 0x02B); msleep(1);
+ rtl8225_write(dev, 0xf, 0x114); msleep(100);
+
+ if (!(rtl8225_read(dev, 6) & (1 << 7))) {
+ rtl8225_write(dev, 0x02, 0x0C4D);
+ msleep(200);
+ rtl8225_write(dev, 0x02, 0x044D);
+ msleep(100);
+ if (!(rtl8225_read(dev, 6) & (1 << 7)))
+ printk(KERN_WARNING "%s: RF Calibration Failed! %x\n",
+ wiphy_name(dev->wiphy), rtl8225_read(dev, 6));
+ }
+
+ rtl8225_write(dev, 0x0, 0x1B7);
+ rtl8225_write(dev, 0x3, 0x002);
+ rtl8225_write(dev, 0x5, 0x004);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225z2_rxgain); i++) {
+ rtl8225_write(dev, 0x1, i + 1);
+ rtl8225_write(dev, 0x2, rtl8225z2_rxgain[i]);
+ }
+
+ rtl8225_write(dev, 0x0, 0x0B7); msleep(100);
+ rtl8225_write(dev, 0x2, 0xC4D);
+
+ msleep(200);
+ rtl8225_write(dev, 0x2, 0x44D);
+ msleep(100);
+
+ rtl8225_write(dev, 0x00, 0x2BF);
+ rtl8225_write(dev, 0xFF, 0xFFFF);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) {
+ rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]);
+ msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i);
+ msleep(1);
+ }
+
+ msleep(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x00, 0x01); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x01, 0x02); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x02, 0x62); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x03, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x04, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x05, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x06, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x07, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x08, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0a, 0x09); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0d, 0x43);
+ rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x10, 0x84); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x11, 0x06); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x12, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x13, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x14, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x15, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x16, 0x00); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x17, 0x40); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x19, 0x19); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1b, 0x11); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1d, 0xc5); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1e, 0xb3); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x21, 0x27); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x22, 0x16); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x23, 0x80); msleep(1); /* FIXME: not needed? */
+ rtl8225_write_phy_ofdm(dev, 0x24, 0x46); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x25, 0x20); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1);
+ rtl8225_write_phy_ofdm(dev, 0x27, 0x88); msleep(1);
+
+ rtl8225_write_phy_cck(dev, 0x00, 0x98); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x03, 0x20); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x04, 0x7e); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x05, 0x12); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x06, 0xfc); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x07, 0x78); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x08, 0x2e); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x10, 0x93); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x11, 0x88); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x12, 0x47); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x13, 0xd0);
+ rtl8225_write_phy_cck(dev, 0x19, 0x00);
+ rtl8225_write_phy_cck(dev, 0x1a, 0xa0);
+ rtl8225_write_phy_cck(dev, 0x1b, 0x08);
+ rtl8225_write_phy_cck(dev, 0x40, 0x86);
+ rtl8225_write_phy_cck(dev, 0x41, 0x8a); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x42, 0x15); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x43, 0x18); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x44, 0x36); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x45, 0x35); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x46, 0x2e); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x47, 0x25); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x48, 0x1c); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x49, 0x12); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x4a, 0x09); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x4b, 0x04); msleep(1);
+ rtl8225_write_phy_cck(dev, 0x4c, 0x05); msleep(1);
+
+ rtl818x_iowrite8(priv, (u8 __iomem *)((void __iomem *)priv->map + 0x5B), 0x0D); msleep(1);
+
+ rtl8225z2_rf_set_tx_power(dev, 1);
+
+ /* RX antenna default to A */
+ rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); /* B: 0xDB */
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); /* B: 0x10 */
+
+ rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */
+ msleep(1);
+ rtl818x_iowrite32(priv, (__le32 __iomem *)((void __iomem *)priv->map + 0x94), 0x15c00002);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
+}
+
+void rtl8225_rf_stop(struct ieee80211_hw *dev)
+{
+ struct rtl8180_priv *priv = dev->priv;
+ u8 reg;
+
+ rtl8225_write(dev, 0x4, 0x1f); msleep(1);
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_OFF);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_OFF);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+}
+
+void rtl8225_rf_set_channel(struct ieee80211_hw *dev,
+ struct ieee80211_conf *conf)
+{
+ struct rtl8180_priv *priv = dev->priv;
+
+ if (priv->rf_init == rtl8225_rf_init)
+ rtl8225_rf_set_tx_power(dev, conf->channel);
+ else
+ rtl8225z2_rf_set_tx_power(dev, conf->channel);
+
+ rtl8225_write(dev, 0x7, rtl8225_chan[conf->channel - 1]);
+ msleep(10);
+
+ if (conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME) {
+ rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9);
+ rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
+ rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14);
+ rtl818x_iowrite8(priv, &priv->map->EIFS, 81);
+ rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0x73);
+ } else {
+ rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14);
+ rtl818x_iowrite8(priv, &priv->map->SIFS, 0x44);
+ rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24);
+ rtl818x_iowrite8(priv, &priv->map->EIFS, 81);
+ rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0xa5);
+ }
+}
diff --git a/drivers/net/wireless/rtl8180_rtl8225.h b/drivers/net/wireless/rtl8180_rtl8225.h
new file mode 100644
index 0000000..4a62acb
--- /dev/null
+++ b/drivers/net/wireless/rtl8180_rtl8225.h
@@ -0,0 +1,28 @@
+#ifndef RTL8180_RTL8225_H
+#define RTL8180_RTL8225_H
+
+#define RTL8225_ANAPARAM_ON 0xa0000b59
+#define RTL8225_ANAPARAM2_ON 0x860dec11
+#define RTL8225_ANAPARAM_OFF 0xa00beb59
+#define RTL8225_ANAPARAM2_OFF 0x840dec11
+
+int rtl8225_is_z2(struct ieee80211_hw *dev);
+
+void rtl8225_rf_init(struct ieee80211_hw *);
+void rtl8225z2_rf_init(struct ieee80211_hw *);
+void rtl8225_rf_stop(struct ieee80211_hw *);
+void rtl8225_rf_set_channel(struct ieee80211_hw *, struct ieee80211_conf *);
+
+static inline void rtl8225_write_phy_ofdm(struct ieee80211_hw *dev,
+ u8 addr, u8 data)
+{
+ rtl8180_write_phy(dev, addr, data);
+}
+
+static inline void rtl8225_write_phy_cck(struct ieee80211_hw *dev,
+ u8 addr, u8 data)
+{
+ rtl8180_write_phy(dev, addr, data | 0x10000);
+}
+
+#endif /* RTL8180_RTL8225_H */
diff --git a/drivers/net/wireless/rtl818x.h b/drivers/net/wireless/rtl818x.h
index 880d4be..99b8b1b 100644
--- a/drivers/net/wireless/rtl818x.h
+++ b/drivers/net/wireless/rtl818x.h
@@ -58,13 +58,17 @@ struct rtl818x_csr {
#define RTL818X_INT_TX_FO (1 << 15)
__le32 TX_CONF;
#define RTL818X_TX_CONF_LOOPBACK_MAC (1 << 17)
+#define RTL818X_TX_CONF_LOOPBACK_CONT (3 << 17)
#define RTL818X_TX_CONF_NO_ICV (1 << 19)
#define RTL818X_TX_CONF_DISCW (1 << 20)
+#define RTL818X_TX_CONF_SAT_HWPLCP (1 << 24)
#define RTL818X_TX_CONF_R8180_ABCD (2 << 25)
#define RTL818X_TX_CONF_R8180_F (3 << 25)
#define RTL818X_TX_CONF_R8185_ABC (4 << 25)
#define RTL818X_TX_CONF_R8185_D (5 << 25)
#define RTL818X_TX_CONF_HWVER_MASK (7 << 25)
+#define RTL818X_TX_CONF_PROBE_DTS (1 << 29)
+#define RTL818X_TX_CONF_HW_SEQNUM (1 << 30)
#define RTL818X_TX_CONF_CW_MIN (1 << 31)
__le32 RX_CONF;
#define RTL818X_RX_CONF_MONITOR (1 << 0)
@@ -75,8 +79,12 @@ struct rtl818x_csr {
#define RTL818X_RX_CONF_DATA (1 << 18)
#define RTL818X_RX_CONF_CTRL (1 << 19)
#define RTL818X_RX_CONF_MGMT (1 << 20)
+#define RTL818X_RX_CONF_ADDR3 (1 << 21)
+#define RTL818X_RX_CONF_PM (1 << 22)
#define RTL818X_RX_CONF_BSSID (1 << 23)
#define RTL818X_RX_CONF_RX_AUTORESETPHY (1 << 28)
+#define RTL818X_RX_CONF_CSDM1 (1 << 29)
+#define RTL818X_RX_CONF_CSDM2 (1 << 30)
#define RTL818X_RX_CONF_ONLYERLPKT (1 << 31)
__le32 INT_TIMEOUT;
__le32 TBDA;
@@ -92,6 +100,7 @@ struct rtl818x_csr {
u8 CONFIG0;
u8 CONFIG1;
u8 CONFIG2;
+#define RTL818X_CONFIG2_ANTENNA_DIV (1 << 6)
__le32 ANAPARAM;
u8 MSR;
#define RTL818X_MSR_NO_LINK (0 << 2)
@@ -111,7 +120,8 @@ struct rtl818x_csr {
__le16 ATIM_WND;
__le16 BEACON_INTERVAL_TIME;
__le16 ATIMTR_INTERVAL;
- u8 reserved_11[4];
+ __le16 PHY_DELAY;
+ u8 reserved_11[2];
u8 PHY[4];
__le16 RFPinsOutput;
__le16 RFPinsEnable;
@@ -149,8 +159,10 @@ struct rtl818x_csr {
u8 RETRY_CTR;
u8 reserved_18[5];
__le32 RDSAR;
- u8 reserved_19[18];
- u16 TALLY_CNT;
+ u8 reserved_19[12];
+ __le16 FEMR;
+ u8 reserved_20[4];
+ __le16 TALLY_CNT;
u8 TALLY_SEL;
} __attribute__((packed));
-
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
