This patch adds a mac80211 based wireless driver for the rtl8187 USB wireless card. Signed-off-by: Michael Wu <flamingice@xxxxxxxxxxxx> --- MAINTAINERS | 10 drivers/net/wireless/Kconfig | 12 + drivers/net/wireless/Makefile | 3 drivers/net/wireless/rtl8187.h | 131 ++++++ drivers/net/wireless/rtl8187_dev.c | 731 +++++++++++++++++++++++++++++++ drivers/net/wireless/rtl8187_rtl8225.c | 744 ++++++++++++++++++++++++++++++++ drivers/net/wireless/rtl8187_rtl8225.h | 30 + drivers/net/wireless/rtl818x.h | 212 +++++++++ 8 files changed, 1873 insertions(+), 0 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index b36923e..68f573d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2922,6 +2922,16 @@ S: Maintained RISCOM8 DRIVER S: Orphan +RTL818X WIRELESS DRIVER +P: Michael Wu +M: flamingice@xxxxxxxxxxxx +P: Andrea Merello +M: andreamrl@xxxxxxxxxx +L: linux-wireless@xxxxxxxxxxxxxxx +W: http://linuxwireless.org/ +T: git kernel.org:/pub/scm/linux/kernel/git/mwu/mac80211-drivers.git +S: Maintained + S3 SAVAGE FRAMEBUFFER DRIVER P: Antonino Daplas M: adaplas@xxxxxxxxx diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig index c4b3dc2..101de0e 100644 --- a/drivers/net/wireless/Kconfig +++ b/drivers/net/wireless/Kconfig @@ -538,6 +538,18 @@ config USB_ZD1201 To compile this driver as a module, choose M here: the module will be called zd1201. +config RTL8187 + tristate "Realtek 8187 USB support" + depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL + select EEPROM_93CX6 + ---help--- + This is a driver for RTL8187 based cards. + These are USB based chips found in cards such as: + + Netgear WG111v2 + + Thanks to Realtek for their support! + source "drivers/net/wireless/hostap/Kconfig" source "drivers/net/wireless/bcm43xx/Kconfig" source "drivers/net/wireless/zd1211rw/Kconfig" diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile index d212460..ef35bc6 100644 --- a/drivers/net/wireless/Makefile +++ b/drivers/net/wireless/Makefile @@ -44,3 +44,6 @@ obj-$(CONFIG_PCMCIA_WL3501) += wl3501_cs obj-$(CONFIG_USB_ZD1201) += zd1201.o obj-$(CONFIG_LIBERTAS_USB) += libertas/ + +rtl8187-objs := rtl8187_dev.o rtl8187_rtl8225.o +obj-$(CONFIG_RTL8187) += rtl8187.o diff --git a/drivers/net/wireless/rtl8187.h b/drivers/net/wireless/rtl8187.h new file mode 100644 index 0000000..41d0aac --- /dev/null +++ b/drivers/net/wireless/rtl8187.h @@ -0,0 +1,131 @@ +#ifndef RTL8187_H +#define RTL8187_H + +#include "rtl818x.h" + +#define RTL8187_EEPROM_TXPWR_BASE 0x05 +#define RTL8187_EEPROM_MAC_ADDR 0x07 +#define RTL8187_EEPROM_TXPWR_CHAN_1 0x16 /* 3 channels */ +#define RTL8187_EEPROM_TXPWR_CHAN_6 0x1B /* 2 channels */ +#define RTL8187_EEPROM_TXPWR_CHAN_4 0x3D /* 2 channels */ + +#define RTL8187_REQT_READ 0xC0 +#define RTL8187_REQT_WRITE 0x40 +#define RTL8187_REQ_GET_REG 0x05 +#define RTL8187_REQ_SET_REG 0x05 + +#define RTL8187_MAX_RX 0x9C4 + +struct rtl8187_rx_info { + struct urb *urb; + struct ieee80211_hw *dev; +}; + +struct rtl8187_rx_hdr { + __le16 len; + __le16 rate; + u8 noise; + u8 signal; + u8 agc; + u8 reserved; + __le64 mac_time; +} __attribute__((packed)); + +struct rtl8187_tx_info { + struct ieee80211_tx_control *control; + struct urb *urb; + struct ieee80211_hw *dev; +}; + +struct rtl8187_tx_hdr { + __le32 flags; +#define RTL8187_TX_FLAG_NO_ENCRYPT (1 << 15) +#define RTL8187_TX_FLAG_MORE_FRAG (1 << 17) +#define RTL8187_TX_FLAG_CTS (1 << 18) +#define RTL8187_TX_FLAG_RTS (1 << 23) + __le16 rts_duration; + __le16 len; + __le32 retry; +} __attribute__((packed)); + +struct rtl8187_priv { + /* common between rtl818x drivers */ + struct rtl818x_csr *map; + void (*rf_init)(struct ieee80211_hw *); + int mode; + + /* rtl8187 specific */ + struct ieee80211_channel channels[14]; + struct ieee80211_rate rates[12]; + struct ieee80211_hw_mode modes[2]; + struct usb_device *udev; + u8 *hwaddr; + u16 txpwr_base; + u8 asic_rev; + struct sk_buff_head rx_queue; +}; + +void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data); + +static inline u8 rtl818x_ioread8(struct rtl8187_priv *priv, u8 *addr) +{ + u8 val; + + usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0), + RTL8187_REQ_GET_REG, RTL8187_REQT_READ, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); + + return val; +} + +static inline u16 rtl818x_ioread16(struct rtl8187_priv *priv, __le16 *addr) +{ + __le16 val; + + usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0), + RTL8187_REQ_GET_REG, RTL8187_REQT_READ, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); + + return le16_to_cpu(val); +} + +static inline u32 rtl818x_ioread32(struct rtl8187_priv *priv, __le32 *addr) +{ + __le32 val; + + usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0), + RTL8187_REQ_GET_REG, RTL8187_REQT_READ, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); + + return le32_to_cpu(val); +} + +static inline void rtl818x_iowrite8(struct rtl8187_priv *priv, + u8 *addr, u8 val) +{ + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); +} + +static inline void rtl818x_iowrite16(struct rtl8187_priv *priv, + __le16 *addr, u16 val) +{ + __le16 buf = cpu_to_le16(val); + + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + (unsigned long)addr, 0, &buf, sizeof(buf), HZ / 2); +} + +static inline void rtl818x_iowrite32(struct rtl8187_priv *priv, + __le32 *addr, u32 val) +{ + __le32 buf = cpu_to_le32(val); + + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + (unsigned long)addr, 0, &buf, sizeof(buf), HZ / 2); +} + +#endif /* RTL8187_H */ diff --git a/drivers/net/wireless/rtl8187_dev.c b/drivers/net/wireless/rtl8187_dev.c new file mode 100644 index 0000000..8365610 --- /dev/null +++ b/drivers/net/wireless/rtl8187_dev.c @@ -0,0 +1,731 @@ + +/* + * Linux device driver for RTL8187 + * + * Copyright 2007 Michael Wu <flamingice@xxxxxxxxxxxx> + * Copyright 2007 Andrea Merello <andreamrl@xxxxxxxxxx> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@xxxxxxxxxx>, et al. + * + * Thanks to Realtek for their support! + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/usb.h> +#include <linux/delay.h> +#include <linux/etherdevice.h> +#include <linux/eeprom_93cx6.h> +#include <net/mac80211.h> + +#include "rtl8187.h" +#include "rtl8187_rtl8225.h" + +MODULE_AUTHOR("Michael Wu <flamingice@xxxxxxxxxxxx>"); +MODULE_AUTHOR("Andrea Merello <andreamrl@xxxxxxxxxx>"); +MODULE_DESCRIPTION("RTL8187 USB wireless driver"); +MODULE_LICENSE("GPL"); + +static struct usb_device_id rtl8187_table[] __devinitdata = { + /* Realtek */ + {USB_DEVICE(0x0bda, 0x8187)}, + /* Netgear */ + {USB_DEVICE(0x0846, 0x6100)}, + {USB_DEVICE(0x0846, 0x6a00)}, + {} +}; + +MODULE_DEVICE_TABLE(usb, rtl8187_table); + +void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data) +{ + struct rtl8187_priv *priv = dev->priv; + + data <<= 8; + data |= addr | 0x80; + + rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF); + rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF); + rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF); + rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF); + + msleep(1); +} + +static void rtl8187_tx_cb(struct urb *urb) +{ + struct ieee80211_tx_status status = { {0} }; + struct sk_buff *skb = (struct sk_buff *)urb->context; + struct rtl8187_tx_info *info = (struct rtl8187_tx_info *)skb->cb; + + usb_free_urb(info->urb); + if (info->control) + memcpy(&status.control, info->control, sizeof(status.control)); + kfree(info->control); + skb_pull(skb, sizeof(struct rtl8187_tx_hdr)); + status.flags |= IEEE80211_TX_STATUS_ACK; + ieee80211_tx_status_irqsafe(info->dev, skb, &status); +} + +static int rtl8187_tx(struct ieee80211_hw *dev, struct sk_buff *skb, + struct ieee80211_tx_control *control) +{ + struct rtl8187_priv *priv = dev->priv; + struct rtl8187_tx_hdr *hdr; + struct rtl8187_tx_info *info; + struct urb *urb; + u32 tmp; + + urb = usb_alloc_urb(0, GFP_ATOMIC); + if (!urb) { + kfree_skb(skb); + return 0; + } + + hdr = (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr)); + tmp = skb->len - sizeof(*hdr); + tmp |= RTL8187_TX_FLAG_NO_ENCRYPT; + tmp |= control->rts_cts_rate << 19; + tmp |= control->tx_rate << 24; + if (ieee80211_get_morefrag((struct ieee80211_hdr *)skb)) + tmp |= RTL8187_TX_FLAG_MORE_FRAG; + if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS) { + tmp |= RTL8187_TX_FLAG_RTS; + hdr->rts_duration = + ieee80211_rts_duration(dev, skb->len, control); + } + if (control->flags & IEEE80211_TXCTL_USE_CTS_PROTECT) + tmp |= RTL8187_TX_FLAG_CTS; + hdr->flags = cpu_to_le32(tmp); + hdr->len = 0; + tmp = control->retry_limit << 8; + hdr->retry = cpu_to_le32(tmp); + + info = (struct rtl8187_tx_info *)skb->cb; + info->control = kmemdup(control, sizeof(*control), GFP_ATOMIC); + info->urb = urb; + info->dev = dev; + usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, 2), + hdr, skb->len, rtl8187_tx_cb, skb); + usb_submit_urb(urb, GFP_ATOMIC); + + return 0; +} + +static void rtl8187_rx_cb(struct urb *urb) +{ + struct sk_buff *skb = (struct sk_buff *)urb->context; + struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb; + struct ieee80211_hw *dev = info->dev; + struct rtl8187_priv *priv = dev->priv; + struct rtl8187_rx_hdr *hdr; + struct ieee80211_rx_status rx_status = { 0 }; + int rate, signal; + + spin_lock(&priv->rx_queue.lock); + if (skb->next) + __skb_unlink(skb, &priv->rx_queue); + else { + spin_unlock(&priv->rx_queue.lock); + return; + } + spin_unlock(&priv->rx_queue.lock); + + if (unlikely(urb->status)) { + usb_free_urb(urb); + dev_kfree_skb_irq(skb); + return; + } + + skb_put(skb, urb->actual_length); + hdr = (struct rtl8187_rx_hdr *)(skb_tail_pointer(skb) - sizeof(*hdr)); + skb_trim(skb, le16_to_cpu(hdr->len) & 0x0FFF); + + signal = hdr->agc >> 1; + rate = (le16_to_cpu(hdr->rate) >> 4) & 0xF; + if (rate > 3) { /* OFDM rate */ + if (signal > 90) + signal = 90; + else if (signal < 25) + signal = 25; + signal = 90 - signal; + } else { /* CCK rate */ + if (signal > 95) + signal = 95; + else if (signal < 30) + signal = 30; + signal = 95 - signal; + } + + rx_status.antenna = (hdr->signal >> 7) & 1; + rx_status.signal = 64 - min(hdr->noise, (u8)64); + rx_status.ssi = signal; + rx_status.rate = rate; + rx_status.freq = dev->conf.freq; + rx_status.channel = dev->conf.channel; + rx_status.phymode = dev->conf.phymode; + rx_status.mactime = le64_to_cpu(hdr->mac_time); + ieee80211_rx_irqsafe(dev, skb, &rx_status); + + skb = dev_alloc_skb(RTL8187_MAX_RX); + if (unlikely(!skb)) { + usb_free_urb(urb); + /* TODO check rx queue length and refill *somewhere* */ + return; + } + + info = (struct rtl8187_rx_info *)skb->cb; + info->urb = urb; + info->dev = dev; + urb->transfer_buffer = skb_tail_pointer(skb); + urb->context = skb; + skb_queue_tail(&priv->rx_queue, skb); + + usb_submit_urb(urb, GFP_ATOMIC); +} + +static int rtl8187_init_urbs(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + struct urb *entry; + struct sk_buff *skb; + struct rtl8187_rx_info *info; + + while (skb_queue_len(&priv->rx_queue) < 8) { + skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL); + if (!skb) + break; + entry = usb_alloc_urb(0, GFP_KERNEL); + if (!entry) { + kfree_skb(skb); + break; + } + usb_fill_bulk_urb(entry, priv->udev, + usb_rcvbulkpipe(priv->udev, 1), + skb_tail_pointer(skb), + RTL8187_MAX_RX, rtl8187_rx_cb, skb); + info = (struct rtl8187_rx_info *)skb->cb; + info->urb = entry; + info->dev = dev; + skb_queue_tail(&priv->rx_queue, skb); + usb_submit_urb(entry, GFP_KERNEL); + } + + return 0; +} + +static int rtl8187_init_hw(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + u8 reg; + int i; + + /* reset */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); + + msleep(200); + rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10); + rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11); + rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00); + msleep(200); + + reg = rtl818x_ioread8(priv, &priv->map->CMD); + reg &= (1 << 1); + reg |= RTL818X_CMD_RESET; + rtl818x_iowrite8(priv, &priv->map->CMD, reg); + + i = 10; + do { + msleep(2); + if (!(rtl818x_ioread8(priv, &priv->map->CMD) & + RTL818X_CMD_RESET)) + break; + } while (--i); + + if (!i) { + printk(KERN_ERR "%s: Reset timeout!\n", wiphy_name(dev->wiphy)); + return -ETIMEDOUT; + } + + /* reload registers from eeprom */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD); + + i = 10; + do { + msleep(4); + if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) & + RTL818X_EEPROM_CMD_CONFIG)) + break; + } while (--i); + + if (!i) { + printk(KERN_ERR "%s: eeprom reset timeout!\n", + wiphy_name(dev->wiphy)); + return -ETIMEDOUT; + } + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + /* setup card */ + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); + rtl818x_iowrite8(priv, &priv->map->GPIO, 0); + + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); + rtl818x_iowrite8(priv, &priv->map->GPIO, 1); + rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + for (i = 0; i < ETH_ALEN; i++) + rtl818x_iowrite8(priv, &priv->map->MAC[i], priv->hwaddr[i]); + + rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG1); + reg &= 0x3F; + reg |= 0x80; + rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); + rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); + rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0x81); + + // TODO: set RESP_RATE and BRSR properly + rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0); + rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); + + /* host_usb_init */ + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); + rtl818x_iowrite8(priv, &priv->map->GPIO, 0); + reg = rtl818x_ioread8(priv, (u8 *)0xFE53); + rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7)); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); + rtl818x_iowrite8(priv, &priv->map->GPIO, 0x20); + rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80); + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80); + msleep(100); + + rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008); + rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF); + rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7); + msleep(100); + + priv->rf_init(dev); + + rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); + reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & 0xfffe; + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 0x1); + rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10); + rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80); + rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60); + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg); + + return 0; +} + +static void rtl8187_set_channel(struct ieee80211_hw *dev, int channel) +{ + u32 reg; + struct rtl8187_priv *priv = dev->priv; + + reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); + /* Enable TX loopback on MAC level to avoid TX during channel + * changes, as this has be seen to causes problems and the + * card will stop work until next reset + */ + rtl818x_iowrite32(priv, &priv->map->TX_CONF, + reg | RTL818X_TX_CONF_LOOPBACK_MAC); + msleep(10); + rtl8225_rf_set_channel(dev, channel); + msleep(10); + rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); +} + +static int rtl8187_open(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + u32 reg; + int ret; + + ret = rtl8187_init_hw(dev); + if (ret) + return ret; + + rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); + + rtl8187_init_urbs(dev); + + reg = RTL818X_RX_CONF_ONLYERLPKT | + RTL818X_RX_CONF_RX_AUTORESETPHY | + RTL818X_RX_CONF_BSSID | + RTL818X_RX_CONF_MGMT | + RTL818X_RX_CONF_CTRL | + RTL818X_RX_CONF_DATA | + (7 << 13 /* RX FIFO threshold NONE */) | + (7 << 10 /* MAX RX DMA */) | + RTL818X_RX_CONF_BROADCAST | + RTL818X_RX_CONF_MULTICAST | + RTL818X_RX_CONF_NICMAC; + if (priv->mode == IEEE80211_IF_TYPE_MNTR) + reg |= RTL818X_RX_CONF_MONITOR; + + rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); + + reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); + reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT; + reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT; + rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); + + reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); + reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT; + reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT; + reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT; + rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); + + reg = RTL818X_TX_CONF_CW_MIN | + (7 << 21 /* MAX TX DMA */) | + RTL818X_TX_CONF_NO_ICV; + rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); + + reg = rtl818x_ioread8(priv, &priv->map->CMD); + reg |= RTL818X_CMD_TX_ENABLE; + reg |= RTL818X_CMD_RX_ENABLE; + rtl818x_iowrite8(priv, &priv->map->CMD, reg); + + return 0; +} + +static int rtl8187_stop(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + struct rtl8187_rx_info *info; + struct sk_buff *skb; + u32 reg; + + rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); + + reg = rtl818x_ioread8(priv, &priv->map->CMD); + reg &= ~RTL818X_CMD_TX_ENABLE; + reg &= ~RTL818X_CMD_RX_ENABLE; + rtl818x_iowrite8(priv, &priv->map->CMD, reg); + + rtl8225_rf_stop(dev); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG4); + rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + while ((skb = skb_dequeue(&priv->rx_queue))) { + info = (struct rtl8187_rx_info *)skb->cb; + usb_kill_urb(info->urb); + kfree_skb(skb); + } + return 0; +} + +static int rtl8187_add_interface(struct ieee80211_hw *dev, + struct ieee80211_if_init_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + + /* NOTE: using IEEE80211_IF_TYPE_MGMT to indicate no mode selected */ + if (priv->mode != IEEE80211_IF_TYPE_MGMT) + return -1; + + switch (conf->type) { + case IEEE80211_IF_TYPE_STA: + case IEEE80211_IF_TYPE_MNTR: + priv->mode = conf->type; + break; + default: + return -EOPNOTSUPP; + } + + priv->hwaddr = conf->mac_addr; + + return 0; +} + +static void rtl8187_remove_interface(struct ieee80211_hw *dev, + struct ieee80211_if_init_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + priv->mode = IEEE80211_IF_TYPE_MGMT; +} + +static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + rtl8187_set_channel(dev, conf->channel); + + rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22); + + if (conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME) { + rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9); + rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14); + rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14); + rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0x73); + } else { + rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14); + rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24); + rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24); + rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0xa5); + } + + rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2); + rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100); + rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100); + rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100); + return 0; +} + +static int rtl8187_config_interface(struct ieee80211_hw *dev, int if_id, + struct ieee80211_if_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + int i; + + for (i = 0; i < ETH_ALEN; i++) + rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]); + + if (is_valid_ether_addr(conf->bssid)) + rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_INFRA); + else + rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_NO_LINK); + + return 0; +} + +static const struct ieee80211_ops rtl8187_ops = { + .tx = rtl8187_tx, + .open = rtl8187_open, + .stop = rtl8187_stop, + .add_interface = rtl8187_add_interface, + .remove_interface = rtl8187_remove_interface, + .config = rtl8187_config, + .config_interface = rtl8187_config_interface, +}; + +static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom) +{ + struct ieee80211_hw *dev = eeprom->data; + struct rtl8187_priv *priv = dev->priv; + u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); + + eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE; + eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ; + eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK; + eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS; +} + +static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom) +{ + struct ieee80211_hw *dev = eeprom->data; + struct rtl8187_priv *priv = dev->priv; + u8 reg = RTL818X_EEPROM_CMD_PROGRAM; + + if (eeprom->reg_data_in) + reg |= RTL818X_EEPROM_CMD_WRITE; + if (eeprom->reg_data_out) + reg |= RTL818X_EEPROM_CMD_READ; + if (eeprom->reg_data_clock) + reg |= RTL818X_EEPROM_CMD_CK; + if (eeprom->reg_chip_select) + reg |= RTL818X_EEPROM_CMD_CS; + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg); + udelay(10); +} + +static int __devinit rtl8187_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(intf); + struct ieee80211_hw *dev; + struct rtl8187_priv *priv; + struct eeprom_93cx6 eeprom; + struct ieee80211_channel *channel; + u16 txpwr, reg; + int err, i; + + dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops); + if (!dev) { + printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n"); + return -ENOMEM; + } + + priv = dev->priv; + + SET_IEEE80211_DEV(dev, &intf->dev); + usb_set_intfdata(intf, dev); + priv->udev = udev; + + usb_get_dev(udev); + + skb_queue_head_init(&priv->rx_queue); + memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels)); + memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates)); + priv->map = (struct rtl818x_csr *)0xFF00; + priv->modes[0].mode = MODE_IEEE80211G; + priv->modes[0].num_rates = ARRAY_SIZE(rtl818x_rates); + priv->modes[0].rates = priv->rates; + priv->modes[0].num_channels = ARRAY_SIZE(rtl818x_channels); + priv->modes[0].channels = priv->channels; + priv->modes[1].mode = MODE_IEEE80211B; + priv->modes[1].num_rates = 4; + priv->modes[1].rates = priv->rates; + priv->modes[1].num_channels = ARRAY_SIZE(rtl818x_channels); + priv->modes[1].channels = priv->channels; + priv->mode = IEEE80211_IF_TYPE_MGMT; + dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING | + IEEE80211_HW_RX_INCLUDES_FCS | + IEEE80211_HW_WEP_INCLUDE_IV | + IEEE80211_HW_DATA_NULLFUNC_ACK; + dev->extra_tx_headroom = sizeof(struct rtl8187_tx_hdr); + dev->queues = 1; + dev->max_rssi = 65; + dev->max_signal = 64; + + for (i = 0; i < 2; i++) + if ((err = ieee80211_register_hwmode(dev, &priv->modes[i]))) + goto err_free_dev; + + eeprom.data = dev; + eeprom.register_read = rtl8187_eeprom_register_read; + eeprom.register_write = rtl8187_eeprom_register_write; + if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6)) + eeprom.width = PCI_EEPROM_WIDTH_93C66; + else + eeprom.width = PCI_EEPROM_WIDTH_93C46; + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + udelay(10); + + eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR, + (__le16 __force *)dev->wiphy->perm_addr, 3); + if (!is_valid_ether_addr(dev->wiphy->perm_addr)) { + printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly " + "generated MAC address\n"); + random_ether_addr(dev->wiphy->perm_addr); + } + + channel = priv->channels; + for (i = 0; i < 3; i++) { + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i, + &txpwr); + (*channel++).val = txpwr & 0xFF; + (*channel++).val = txpwr >> 8; + } + for (i = 0; i < 2; i++) { + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i, + &txpwr); + (*channel++).val = txpwr & 0xFF; + (*channel++).val = txpwr >> 8; + } + for (i = 0; i < 2; i++) { + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6 + i, + &txpwr); + (*channel++).val = txpwr & 0xFF; + (*channel++).val = txpwr >> 8; + } + + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE, + &priv->txpwr_base); + + reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & ~1; + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 1); + /* 0 means asic B-cut, we should use SW 3 wire + * bit-by-bit banging for radio. 1 means we can use + * USB specific request to write radio registers */ + priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3; + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl8225_write(dev, 0, 0x1B7); + + if (rtl8225_read(dev, 8) != 0x588 || rtl8225_read(dev, 9) != 0x700) + priv->rf_init = rtl8225_rf_init; + else + priv->rf_init = rtl8225z2_rf_init; + + rtl8225_write(dev, 0, 0x0B7); + + err = ieee80211_register_hw(dev); + if (err) { + printk(KERN_ERR "rtl8187: Cannot register device\n"); + goto err_free_dev; + } + + printk(KERN_INFO "%s: hwaddr " MAC_FMT ", rtl8187 V%d + %s\n", + wiphy_name(dev->wiphy), MAC_ARG(dev->wiphy->perm_addr), + priv->asic_rev, priv->rf_init == rtl8225_rf_init ? + "rtl8225" : "rtl8225z2"); + + return 0; + + err_free_dev: + ieee80211_free_hw(dev); + usb_set_intfdata(intf, NULL); + usb_put_dev(udev); + return err; +} + +static void __devexit rtl8187_disconnect(struct usb_interface *intf) +{ + struct ieee80211_hw *dev = usb_get_intfdata(intf); + struct rtl8187_priv *priv; + + if (!dev) + return; + + ieee80211_unregister_hw(dev); + + priv = dev->priv; + usb_put_dev(interface_to_usbdev(intf)); + ieee80211_free_hw(dev); +} + +static struct usb_driver rtl8187_driver = { + .name = KBUILD_MODNAME, + .id_table = rtl8187_table, + .probe = rtl8187_probe, + .disconnect = rtl8187_disconnect, +}; + +static int __init rtl8187_init(void) +{ + return usb_register(&rtl8187_driver); +} + +static void __exit rtl8187_exit(void) +{ + usb_deregister(&rtl8187_driver); +} + +module_init(rtl8187_init); +module_exit(rtl8187_exit); diff --git a/drivers/net/wireless/rtl8187_rtl8225.c b/drivers/net/wireless/rtl8187_rtl8225.c new file mode 100644 index 0000000..c3f5bf5 --- /dev/null +++ b/drivers/net/wireless/rtl8187_rtl8225.c @@ -0,0 +1,744 @@ + +/* + * Radio tuning for RTL8225 on RTL8187 + * + * Copyright 2007 Michael Wu <flamingice@xxxxxxxxxxxx> + * Copyright 2007 Andrea Merello <andreamrl@xxxxxxxxxx> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@xxxxxxxxxx>, et al. + * + * Thanks to Realtek for their support! + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/usb.h> +#include <net/mac80211.h> + +#include "rtl8187.h" +#include "rtl8187_rtl8225.h" + +static void rtl8225_write_bitbang(struct ieee80211_hw *dev, u8 addr, u16 data) +{ + struct rtl8187_priv *priv = dev->priv; + u16 reg80, reg84, reg82; + u32 bangdata; + int i; + + bangdata = (data << 4) | (addr & 0xf); + + reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput) & 0xfff3; + reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable); + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x7); + + reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x7); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80); + udelay(10); + + for (i = 15; i >= 0; i--) { + u16 reg = reg80 | (bangdata & (1 << i)) >> i; + + if (i & 1) + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1)); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1)); + + if (!(i & 1)) + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84); + msleep(2); +} + +static void rtl8225_write_8051(struct ieee80211_hw *dev, u8 addr, u16 data) +{ + struct rtl8187_priv *priv = dev->priv; + u16 reg80, reg82, reg84; + + reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput); + reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable); + reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect); + + reg80 &= ~(0x3 << 2); + reg84 &= ~0xF; + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x0007); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x0007); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(2); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80); + udelay(10); + + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + addr, 0x8225, &data, sizeof(data), HZ / 2); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84); + msleep(2); +} + +void rtl8225_write(struct ieee80211_hw *dev, u8 addr, u16 data) +{ + struct rtl8187_priv *priv = dev->priv; + + if (priv->asic_rev) + rtl8225_write_8051(dev, addr, data); + else + rtl8225_write_bitbang(dev, addr, data); +} + +u16 rtl8225_read(struct ieee80211_hw *dev, u8 addr) +{ + struct rtl8187_priv *priv = dev->priv; + u16 reg80, reg82, reg84, out; + int i; + + reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput); + reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable); + reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect); + + reg80 &= ~0xF; + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x000F); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x000F); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(4); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80); + udelay(5); + + for (i = 4; i >= 0; i--) { + u16 reg = reg80 | ((addr >> i) & 1); + + if (!(i & 1)) { + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + udelay(1); + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg | (1 << 1)); + udelay(2); + + if (i & 1) { + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + udelay(1); + } + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(2); + + out = 0; + for (i = 11; i >= 0; i--) { + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(1); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + + if (rtl818x_ioread16(priv, &priv->map->RFPinsInput) & (1 << 1)) + out |= 1 << i; + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(2); + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 2)); + udelay(2); + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x03A0); + + return out; +} + +static const u16 rtl8225bcd_rxgain[] = { + 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409, + 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541, + 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583, + 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644, + 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688, + 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745, + 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789, + 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793, + 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d, + 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9, + 0x07aa, 0x07ab, 0x07ac, 0x07ad, 0x07b0, 0x07b1, 0x07b2, 0x07b3, + 0x07b4, 0x07b5, 0x07b8, 0x07b9, 0x07ba, 0x07bb, 0x07bb +}; + +static const u8 rtl8225_agc[] = { + 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, + 0x9d, 0x9c, 0x9b, 0x9a, 0x99, 0x98, 0x97, 0x96, + 0x95, 0x94, 0x93, 0x92, 0x91, 0x90, 0x8f, 0x8e, + 0x8d, 0x8c, 0x8b, 0x8a, 0x89, 0x88, 0x87, 0x86, + 0x85, 0x84, 0x83, 0x82, 0x81, 0x80, 0x3f, 0x3e, + 0x3d, 0x3c, 0x3b, 0x3a, 0x39, 0x38, 0x37, 0x36, + 0x35, 0x34, 0x33, 0x32, 0x31, 0x30, 0x2f, 0x2e, + 0x2d, 0x2c, 0x2b, 0x2a, 0x29, 0x28, 0x27, 0x26, + 0x25, 0x24, 0x23, 0x22, 0x21, 0x20, 0x1f, 0x1e, + 0x1d, 0x1c, 0x1b, 0x1a, 0x19, 0x18, 0x17, 0x16, + 0x15, 0x14, 0x13, 0x12, 0x11, 0x10, 0x0f, 0x0e, + 0x0d, 0x0c, 0x0b, 0x0a, 0x09, 0x08, 0x07, 0x06, + 0x05, 0x04, 0x03, 0x02, 0x01, 0x01, 0x01, 0x01, + 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, + 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, + 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01 +}; + +static const u8 rtl8225_gain[] = { + 0x23, 0x88, 0x7c, 0xa5, /* -82dBm */ + 0x23, 0x88, 0x7c, 0xb5, /* -82dBm */ + 0x23, 0x88, 0x7c, 0xc5, /* -82dBm */ + 0x33, 0x80, 0x79, 0xc5, /* -78dBm */ + 0x43, 0x78, 0x76, 0xc5, /* -74dBm */ + 0x53, 0x60, 0x73, 0xc5, /* -70dBm */ + 0x63, 0x58, 0x70, 0xc5, /* -66dBm */ +}; + +static const u8 rtl8225_threshold[] = { + 0x8d, 0x8d, 0x8d, 0x8d, 0x9d, 0xad, 0xbd +}; + +static const u8 rtl8225_tx_gain_cck_ofdm[] = { + 0x02, 0x06, 0x0e, 0x1e, 0x3e, 0x7e +}; + +static const u8 rtl8225_tx_power_cck[] = { + 0x18, 0x17, 0x15, 0x11, 0x0c, 0x08, 0x04, 0x02, + 0x1b, 0x1a, 0x17, 0x13, 0x0e, 0x09, 0x04, 0x02, + 0x1f, 0x1e, 0x1a, 0x15, 0x10, 0x0a, 0x05, 0x02, + 0x22, 0x21, 0x1d, 0x18, 0x11, 0x0b, 0x06, 0x02, + 0x26, 0x25, 0x21, 0x1b, 0x14, 0x0d, 0x06, 0x03, + 0x2b, 0x2a, 0x25, 0x1e, 0x16, 0x0e, 0x07, 0x03 +}; + +static const u8 rtl8225_tx_power_cck_ch14[] = { + 0x18, 0x17, 0x15, 0x0c, 0x00, 0x00, 0x00, 0x00, + 0x1b, 0x1a, 0x17, 0x0e, 0x00, 0x00, 0x00, 0x00, + 0x1f, 0x1e, 0x1a, 0x0f, 0x00, 0x00, 0x00, 0x00, + 0x22, 0x21, 0x1d, 0x11, 0x00, 0x00, 0x00, 0x00, + 0x26, 0x25, 0x21, 0x13, 0x00, 0x00, 0x00, 0x00, + 0x2b, 0x2a, 0x25, 0x15, 0x00, 0x00, 0x00, 0x00 +}; + +static const u8 rtl8225_tx_power_ofdm[] = { + 0x80, 0x90, 0xa2, 0xb5, 0xcb, 0xe4 +}; + +static const u32 rtl8225_chan[] = { + 0x085c, 0x08dc, 0x095c, 0x09dc, 0x0a5c, 0x0adc, 0x0b5c, + 0x0bdc, 0x0c5c, 0x0cdc, 0x0d5c, 0x0ddc, 0x0e5c, 0x0f72 +}; + +static void rtl8225_rf_set_tx_power(struct ieee80211_hw *dev, int channel) +{ + struct rtl8187_priv *priv = dev->priv; + u8 cck_power, ofdm_power; + const u8 *tmp; + u32 reg; + int i; + + cck_power = priv->channels[channel - 1].val & 0xF; + ofdm_power = priv->channels[channel - 1].val >> 4; + + cck_power = min(cck_power, (u8)11); + ofdm_power = min(ofdm_power, (u8)35); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK, + rtl8225_tx_gain_cck_ofdm[cck_power / 6] >> 1); + + if (channel == 14) + tmp = &rtl8225_tx_power_cck_ch14[(cck_power % 6) * 8]; + else + tmp = &rtl8225_tx_power_cck[(cck_power % 6) * 8]; + + for (i = 0; i < 8; i++) + rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++); + + msleep(1); // FIXME: optional? + + /* anaparam2 on */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl8225_write_phy_ofdm(dev, 2, 0x42); + rtl8225_write_phy_ofdm(dev, 6, 0x00); + rtl8225_write_phy_ofdm(dev, 8, 0x00); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM, + rtl8225_tx_gain_cck_ofdm[ofdm_power / 6] >> 1); + + tmp = &rtl8225_tx_power_ofdm[ofdm_power % 6]; + + rtl8225_write_phy_ofdm(dev, 5, *tmp); + rtl8225_write_phy_ofdm(dev, 7, *tmp); + + msleep(1); +} + +void rtl8225_rf_init(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + int i; + + rtl8225_write(dev, 0x0, 0x067); msleep(1); + rtl8225_write(dev, 0x1, 0xFE0); msleep(1); + rtl8225_write(dev, 0x2, 0x44D); msleep(1); + rtl8225_write(dev, 0x3, 0x441); msleep(1); + rtl8225_write(dev, 0x4, 0x486); msleep(1); + rtl8225_write(dev, 0x5, 0xBC0); msleep(1); + rtl8225_write(dev, 0x6, 0xAE6); msleep(1); + rtl8225_write(dev, 0x7, 0x82A); msleep(1); + rtl8225_write(dev, 0x8, 0x01F); msleep(1); + rtl8225_write(dev, 0x9, 0x334); msleep(1); + rtl8225_write(dev, 0xA, 0xFD4); msleep(1); + rtl8225_write(dev, 0xB, 0x391); msleep(1); + rtl8225_write(dev, 0xC, 0x050); msleep(1); + rtl8225_write(dev, 0xD, 0x6DB); msleep(1); + rtl8225_write(dev, 0xE, 0x029); msleep(1); + rtl8225_write(dev, 0xF, 0x914); msleep(100); + + rtl8225_write(dev, 0x2, 0xC4D); msleep(200); + rtl8225_write(dev, 0x2, 0x44D); msleep(200); + + if (!(rtl8225_read(dev, 6) & (1 << 7))) { + rtl8225_write(dev, 0x02, 0x0c4d); + msleep(200); + rtl8225_write(dev, 0x02, 0x044d); + msleep(100); + if (!(rtl8225_read(dev, 6) & (1 << 7))) + printk(KERN_WARNING "%s: RF Calibration Failed! %x\n", + wiphy_name(dev->wiphy), rtl8225_read(dev, 6)); + } + + rtl8225_write(dev, 0x0, 0x127); + + for (i = 0; i < ARRAY_SIZE(rtl8225bcd_rxgain); i++) { + rtl8225_write(dev, 0x1, i + 1); + rtl8225_write(dev, 0x2, rtl8225bcd_rxgain[i]); + } + + rtl8225_write(dev, 0x0, 0x027); + rtl8225_write(dev, 0x0, 0x22F); + + for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) { + rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]); + msleep(1); + rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i); + msleep(1); + } + + msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x00, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x01, 0x02); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x02, 0x42); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x03, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x04, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x05, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x06, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x07, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x08, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0a, 0x09); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x10, 0x84); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x11, 0x06); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x12, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x13, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x14, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x15, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x16, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x17, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x19, 0x19); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1b, 0x76); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x21, 0x27); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x22, 0x16); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x24, 0x46); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x25, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x27, 0x88); msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[2 * 4]); + rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[2 * 4 + 2]); + rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[2 * 4 + 3]); + rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[2 * 4 + 1]); + + rtl8225_write_phy_cck(dev, 0x00, 0x98); msleep(1); + rtl8225_write_phy_cck(dev, 0x03, 0x20); msleep(1); + rtl8225_write_phy_cck(dev, 0x04, 0x7e); msleep(1); + rtl8225_write_phy_cck(dev, 0x05, 0x12); msleep(1); + rtl8225_write_phy_cck(dev, 0x06, 0xfc); msleep(1); + rtl8225_write_phy_cck(dev, 0x07, 0x78); msleep(1); + rtl8225_write_phy_cck(dev, 0x08, 0x2e); msleep(1); + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); + rtl8225_write_phy_cck(dev, 0x11, 0x88); msleep(1); + rtl8225_write_phy_cck(dev, 0x12, 0x47); msleep(1); + rtl8225_write_phy_cck(dev, 0x13, 0xd0); + rtl8225_write_phy_cck(dev, 0x19, 0x00); + rtl8225_write_phy_cck(dev, 0x1a, 0xa0); + rtl8225_write_phy_cck(dev, 0x1b, 0x08); + rtl8225_write_phy_cck(dev, 0x40, 0x86); + rtl8225_write_phy_cck(dev, 0x41, 0x8d); msleep(1); + rtl8225_write_phy_cck(dev, 0x42, 0x15); msleep(1); + rtl8225_write_phy_cck(dev, 0x43, 0x18); msleep(1); + rtl8225_write_phy_cck(dev, 0x44, 0x1f); msleep(1); + rtl8225_write_phy_cck(dev, 0x45, 0x1e); msleep(1); + rtl8225_write_phy_cck(dev, 0x46, 0x1a); msleep(1); + rtl8225_write_phy_cck(dev, 0x47, 0x15); msleep(1); + rtl8225_write_phy_cck(dev, 0x48, 0x10); msleep(1); + rtl8225_write_phy_cck(dev, 0x49, 0x0a); msleep(1); + rtl8225_write_phy_cck(dev, 0x4a, 0x05); msleep(1); + rtl8225_write_phy_cck(dev, 0x4b, 0x02); msleep(1); + rtl8225_write_phy_cck(dev, 0x4c, 0x05); msleep(1); + + rtl818x_iowrite8(priv, &priv->map->TESTR, 0x0D); + + rtl8225_rf_set_tx_power(dev, 1); + + /* RX antenna default to A */ + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); /* B: 0xDB */ + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); /* B: 0x10 */ + + rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */ + msleep(1); + rtl818x_iowrite32(priv, (__le32 *)0xFF94, 0x3dc00002); + + /* set sensitivity */ + rtl8225_write(dev, 0x0c, 0x50); + rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[2 * 4]); + rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[2 * 4 + 2]); + rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[2 * 4 + 3]); + rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[2 * 4 + 1]); + rtl8225_write_phy_cck(dev, 0x41, rtl8225_threshold[2]); +} + +static const u8 rtl8225z2_tx_power_cck_ch14[] = { + 0x36, 0x35, 0x2e, 0x1b, 0x00, 0x00, 0x00, 0x00 +}; + +static const u8 rtl8225z2_tx_power_cck[] = { + 0x36, 0x35, 0x2e, 0x25, 0x1c, 0x12, 0x09, 0x04 +}; + +static const u8 rtl8225z2_tx_power_ofdm[] = { + 0x42, 0x00, 0x40, 0x00, 0x40 +}; + +static const u8 rtl8225z2_tx_gain_cck_ofdm[] = { + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, + 0x06, 0x07, 0x08, 0x09, 0x0a, 0x0b, + 0x0c, 0x0d, 0x0e, 0x0f, 0x10, 0x11, + 0x12, 0x13, 0x14, 0x15, 0x16, 0x17, + 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, + 0x1e, 0x1f, 0x20, 0x21, 0x22, 0x23 +}; + +static void rtl8225z2_rf_set_tx_power(struct ieee80211_hw *dev, int channel) +{ + struct rtl8187_priv *priv = dev->priv; + u8 cck_power, ofdm_power; + const u8 *tmp; + u32 reg; + int i; + + cck_power = priv->channels[channel - 1].val & 0xF; + ofdm_power = priv->channels[channel - 1].val >> 4; + + cck_power = min(cck_power, (u8)15); + cck_power += priv->txpwr_base & 0xF; + cck_power = min(cck_power, (u8)35); + + ofdm_power = min(ofdm_power, (u8)15); + ofdm_power += priv->txpwr_base >> 4; + ofdm_power = min(ofdm_power, (u8)35); + + if (channel == 14) + tmp = rtl8225z2_tx_power_cck_ch14; + else + tmp = rtl8225z2_tx_power_cck; + + for (i = 0; i < 8; i++) + rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK, + rtl8225z2_tx_gain_cck_ofdm[cck_power]); + msleep(1); + + /* anaparam2 on */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl8225_write_phy_ofdm(dev, 2, 0x42); + rtl8225_write_phy_ofdm(dev, 5, 0x00); + rtl8225_write_phy_ofdm(dev, 6, 0x40); + rtl8225_write_phy_ofdm(dev, 7, 0x00); + rtl8225_write_phy_ofdm(dev, 8, 0x40); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM, + rtl8225z2_tx_gain_cck_ofdm[ofdm_power]); + msleep(1); +} + +static const u16 rtl8225z2_rxgain[] = { + 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409, + 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541, + 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583, + 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644, + 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688, + 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745, + 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789, + 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793, + 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d, + 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9, + 0x03aa, 0x03ab, 0x03ac, 0x03ad, 0x03b0, 0x03b1, 0x03b2, 0x03b3, + 0x03b4, 0x03b5, 0x03b8, 0x03b9, 0x03ba, 0x03bb, 0x03bb +}; + +static const u8 rtl8225z2_gain_bg[] = { + 0x23, 0x15, 0xa5, /* -82-1dBm */ + 0x23, 0x15, 0xb5, /* -82-2dBm */ + 0x23, 0x15, 0xc5, /* -82-3dBm */ + 0x33, 0x15, 0xc5, /* -78dBm */ + 0x43, 0x15, 0xc5, /* -74dBm */ + 0x53, 0x15, 0xc5, /* -70dBm */ + 0x63, 0x15, 0xc5 /* -66dBm */ +}; + +void rtl8225z2_rf_init(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + int i; + + rtl8225_write(dev, 0x0, 0x2BF); msleep(1); + rtl8225_write(dev, 0x1, 0xEE0); msleep(1); + rtl8225_write(dev, 0x2, 0x44D); msleep(1); + rtl8225_write(dev, 0x3, 0x441); msleep(1); + rtl8225_write(dev, 0x4, 0x8C3); msleep(1); + rtl8225_write(dev, 0x5, 0xC72); msleep(1); + rtl8225_write(dev, 0x6, 0x0E6); msleep(1); + rtl8225_write(dev, 0x7, 0x82A); msleep(1); + rtl8225_write(dev, 0x8, 0x03F); msleep(1); + rtl8225_write(dev, 0x9, 0x335); msleep(1); + rtl8225_write(dev, 0xa, 0x9D4); msleep(1); + rtl8225_write(dev, 0xb, 0x7BB); msleep(1); + rtl8225_write(dev, 0xc, 0x850); msleep(1); + rtl8225_write(dev, 0xd, 0xCDF); msleep(1); + rtl8225_write(dev, 0xe, 0x02B); msleep(1); + rtl8225_write(dev, 0xf, 0x114); msleep(100); + + rtl8225_write(dev, 0x0, 0x1B7); + + for (i = 0; i < ARRAY_SIZE(rtl8225z2_rxgain); i++) { + rtl8225_write(dev, 0x1, i + 1); + rtl8225_write(dev, 0x2, rtl8225z2_rxgain[i]); + } + + rtl8225_write(dev, 0x3, 0x080); + rtl8225_write(dev, 0x5, 0x004); + rtl8225_write(dev, 0x0, 0x0B7); + rtl8225_write(dev, 0x2, 0xc4D); + + msleep(200); + rtl8225_write(dev, 0x2, 0x44D); + msleep(100); + + if (!(rtl8225_read(dev, 6) & (1 << 7))) { + rtl8225_write(dev, 0x02, 0x0C4D); + msleep(200); + rtl8225_write(dev, 0x02, 0x044D); + msleep(100); + if (!(rtl8225_read(dev, 6) & (1 << 7))) + printk(KERN_WARNING "%s: RF Calibration Failed! %x\n", + wiphy_name(dev->wiphy), rtl8225_read(dev, 6)); + } + + msleep(200); + + rtl8225_write(dev, 0x0, 0x2BF); + + for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) { + rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]); + msleep(1); + rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i); + msleep(1); + } + + msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x00, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x01, 0x02); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x02, 0x42); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x03, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x04, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x05, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x06, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x07, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x08, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0a, 0x08); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0d, 0x43); + rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x10, 0x84); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x11, 0x07); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x12, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x13, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x14, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x15, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x16, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x17, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x19, 0x19); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1b, 0x15); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1d, 0xc5); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x21, 0x17); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x22, 0x16); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x23, 0x80); msleep(1); //FIXME: not needed? + rtl8225_write_phy_ofdm(dev, 0x24, 0x46); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x25, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x27, 0x88); msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x0b, rtl8225z2_gain_bg[4 * 3]); + rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225z2_gain_bg[4 * 3 + 1]); + rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225z2_gain_bg[4 * 3 + 2]); + rtl8225_write_phy_ofdm(dev, 0x21, 0x37); + + rtl8225_write_phy_cck(dev, 0x00, 0x98); msleep(1); + rtl8225_write_phy_cck(dev, 0x03, 0x20); msleep(1); + rtl8225_write_phy_cck(dev, 0x04, 0x7e); msleep(1); + rtl8225_write_phy_cck(dev, 0x05, 0x12); msleep(1); + rtl8225_write_phy_cck(dev, 0x06, 0xfc); msleep(1); + rtl8225_write_phy_cck(dev, 0x07, 0x78); msleep(1); + rtl8225_write_phy_cck(dev, 0x08, 0x2e); msleep(1); + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); + rtl8225_write_phy_cck(dev, 0x11, 0x88); msleep(1); + rtl8225_write_phy_cck(dev, 0x12, 0x47); msleep(1); + rtl8225_write_phy_cck(dev, 0x13, 0xd0); + rtl8225_write_phy_cck(dev, 0x19, 0x00); + rtl8225_write_phy_cck(dev, 0x1a, 0xa0); + rtl8225_write_phy_cck(dev, 0x1b, 0x08); + rtl8225_write_phy_cck(dev, 0x40, 0x86); + rtl8225_write_phy_cck(dev, 0x41, 0x8d); msleep(1); + rtl8225_write_phy_cck(dev, 0x42, 0x15); msleep(1); + rtl8225_write_phy_cck(dev, 0x43, 0x18); msleep(1); + rtl8225_write_phy_cck(dev, 0x44, 0x36); msleep(1); + rtl8225_write_phy_cck(dev, 0x45, 0x35); msleep(1); + rtl8225_write_phy_cck(dev, 0x46, 0x2e); msleep(1); + rtl8225_write_phy_cck(dev, 0x47, 0x25); msleep(1); + rtl8225_write_phy_cck(dev, 0x48, 0x1c); msleep(1); + rtl8225_write_phy_cck(dev, 0x49, 0x12); msleep(1); + rtl8225_write_phy_cck(dev, 0x4a, 0x09); msleep(1); + rtl8225_write_phy_cck(dev, 0x4b, 0x04); msleep(1); + rtl8225_write_phy_cck(dev, 0x4c, 0x05); msleep(1); + + rtl818x_iowrite8(priv, (u8 *)0xFF5B, 0x0D); msleep(1); + + rtl8225z2_rf_set_tx_power(dev, 1); + + /* RX antenna default to A */ + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); /* B: 0xDB */ + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); /* B: 0x10 */ + + rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */ + msleep(1); + rtl818x_iowrite32(priv, (__le32 *)0xFF94, 0x3dc00002); +} + +void rtl8225_rf_stop(struct ieee80211_hw *dev) +{ + u8 reg; + struct rtl8187_priv *priv = dev->priv; + + rtl8225_write(dev, 0x4, 0x1f); msleep(1); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_OFF); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_OFF); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); +} + +void rtl8225_rf_set_channel(struct ieee80211_hw *dev, int channel) +{ + struct rtl8187_priv *priv = dev->priv; + + if (priv->rf_init == rtl8225_rf_init) + rtl8225_rf_set_tx_power(dev, channel); + else + rtl8225z2_rf_set_tx_power(dev, channel); + + rtl8225_write(dev, 0x7, rtl8225_chan[channel - 1]); + msleep(10); +} diff --git a/drivers/net/wireless/rtl8187_rtl8225.h b/drivers/net/wireless/rtl8187_rtl8225.h new file mode 100644 index 0000000..ed28118 --- /dev/null +++ b/drivers/net/wireless/rtl8187_rtl8225.h @@ -0,0 +1,30 @@ +#ifndef RTL8187_RTL8225_H +#define RTL8187_RTL8225_H + +#define RTL8225_ANAPARAM_ON 0xa0000a59 +#define RTL8225_ANAPARAM2_ON 0x860c7312 +#define RTL8225_ANAPARAM_OFF 0xa00beb59 +#define RTL8225_ANAPARAM2_OFF 0x840dec11 + +void rtl8225_write(struct ieee80211_hw *, u8 addr, u16 data); +u16 rtl8225_read(struct ieee80211_hw *, u8 addr); + +void rtl8225_rf_init(struct ieee80211_hw *); +void rtl8225z2_rf_init(struct ieee80211_hw *); +void rtl8225_rf_stop(struct ieee80211_hw *); +void rtl8225_rf_set_channel(struct ieee80211_hw *, int); + + +static inline void rtl8225_write_phy_ofdm(struct ieee80211_hw *dev, + u8 addr, u32 data) +{ + rtl8187_write_phy(dev, addr, data); +} + +static inline void rtl8225_write_phy_cck(struct ieee80211_hw *dev, + u8 addr, u32 data) +{ + rtl8187_write_phy(dev, addr, data | 0x10000); +} + +#endif /* RTL8187_RTL8225_H */ diff --git a/drivers/net/wireless/rtl818x.h b/drivers/net/wireless/rtl818x.h new file mode 100644 index 0000000..e4ee946 --- /dev/null +++ b/drivers/net/wireless/rtl818x.h @@ -0,0 +1,212 @@ +#ifndef RTL818X_H +#define RTL818X_H + +struct rtl818x_csr { + u8 MAC[6]; + u8 reserved_0[2]; + __le32 MAR[2]; + u8 RX_FIFO_COUNT; + u8 reserved_1; + u8 TX_FIFO_COUNT; + u8 BQREQ; + u8 reserved_2[4]; + __le32 TSFT[2]; + __le32 TLPDA; + __le32 TNPDA; + __le32 THPDA; + __le16 BRSR; + u8 BSSID[6]; + u8 RESP_RATE; + u8 EIFS; + u8 reserved_3[1]; + u8 CMD; +#define RTL818X_CMD_TX_ENABLE (1 << 2) +#define RTL818X_CMD_RX_ENABLE (1 << 3) +#define RTL818X_CMD_RESET (1 << 4) + u8 reserved_4[4]; + __le16 INT_MASK; + __le16 INT_STATUS; +#define RTL818X_INT_RX_OK (1 << 0) +#define RTL818X_INT_RX_ERR (1 << 1) +#define RTL818X_INT_TXL_OK (1 << 2) +#define RTL818X_INT_TXL_ERR (1 << 3) +#define RTL818X_INT_RX_DU (1 << 4) +#define RTL818X_INT_RX_FO (1 << 5) +#define RTL818X_INT_TXN_OK (1 << 6) +#define RTL818X_INT_TXN_ERR (1 << 7) +#define RTL818X_INT_TXH_OK (1 << 8) +#define RTL818X_INT_TXH_ERR (1 << 9) +#define RTL818X_INT_TXB_OK (1 << 10) +#define RTL818X_INT_TXB_ERR (1 << 11) +#define RTL818X_INT_ATIM (1 << 12) +#define RTL818X_INT_BEACON (1 << 13) +#define RTL818X_INT_TIME_OUT (1 << 14) +#define RTL818X_INT_TX_FO (1 << 15) + __le32 TX_CONF; +#define RTL818X_TX_CONF_LOOPBACK_MAC (1 << 17) +#define RTL818X_TX_CONF_NO_ICV (1 << 19) +#define RTL818X_TX_CONF_DISCW (1 << 20) +#define RTL818X_TX_CONF_R8180_ABCD (2 << 25) +#define RTL818X_TX_CONF_R8180_F (3 << 25) +#define RTL818X_TX_CONF_R8185_ABC (4 << 25) +#define RTL818X_TX_CONF_R8185_D (5 << 25) +#define RTL818X_TX_CONF_HWVER_MASK (7 << 25) +#define RTL818X_TX_CONF_CW_MIN (1 << 31) + __le32 RX_CONF; +#define RTL818X_RX_CONF_MONITOR (1 << 0) +#define RTL818X_RX_CONF_NICMAC (1 << 1) +#define RTL818X_RX_CONF_MULTICAST (1 << 2) +#define RTL818X_RX_CONF_BROADCAST (1 << 3) +#define RTL818X_RX_CONF_DATA (1 << 18) +#define RTL818X_RX_CONF_CTRL (1 << 19) +#define RTL818X_RX_CONF_MGMT (1 << 20) +#define RTL818X_RX_CONF_BSSID (1 << 23) +#define RTL818X_RX_CONF_RX_AUTORESETPHY (1 << 28) +#define RTL818X_RX_CONF_ONLYERLPKT (1 << 31) + __le32 INT_TIMEOUT; + __le32 TBDA; + u8 EEPROM_CMD; +#define RTL818X_EEPROM_CMD_READ (1 << 0) +#define RTL818X_EEPROM_CMD_WRITE (1 << 1) +#define RTL818X_EEPROM_CMD_CK (1 << 2) +#define RTL818X_EEPROM_CMD_CS (1 << 3) +#define RTL818X_EEPROM_CMD_NORMAL (0 << 6) +#define RTL818X_EEPROM_CMD_LOAD (1 << 6) +#define RTL818X_EEPROM_CMD_PROGRAM (2 << 6) +#define RTL818X_EEPROM_CMD_CONFIG (3 << 6) + u8 CONFIG0; + u8 CONFIG1; + u8 CONFIG2; + __le32 ANAPARAM; + u8 MSR; +#define RTL818X_MSR_NO_LINK (0 << 2) +#define RTL818X_MSR_ADHOC (1 << 2) +#define RTL818X_MSR_INFRA (2 << 2) + u8 CONFIG3; +#define RTL818X_CONFIG3_ANAPARAM_WRITE (1 << 6) + u8 CONFIG4; +#define RTL818X_CONFIG4_POWEROFF (1 << 6) +#define RTL818X_CONFIG4_VCOOFF (1 << 7) + u8 TESTR; + u8 reserved_9[2]; + __le16 PGSELECT; + __le32 ANAPARAM2; + u8 reserved_10[12]; + __le16 BEACON_INTERVAL; + __le16 ATIM_WND; + __le16 BEACON_INTERVAL_TIME; + __le16 ATIMTR_INTERVAL; + u8 reserved_11[4]; + u8 PHY[4]; + __le16 RFPinsOutput; + __le16 RFPinsEnable; + __le16 RFPinsSelect; + __le16 RFPinsInput; + __le32 RF_PARA; + __le32 RF_TIMING; + u8 GP_ENABLE; + u8 GPIO; + u8 reserved_12[10]; + u8 TX_AGC_CTL; +#define RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT (1 << 0) +#define RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT (1 << 1) +#define RTL818X_TX_AGC_CTL_FEEDBACK_ANT (1 << 2) + u8 TX_GAIN_CCK; + u8 TX_GAIN_OFDM; + u8 TX_ANTENNA; + u8 reserved_13[16]; + u8 WPA_CONF; + u8 reserved_14[3]; + u8 SIFS; + u8 DIFS; + u8 SLOT; + u8 reserved_15[5]; + u8 CW_CONF; +#define RTL818X_CW_CONF_PERPACKET_CW_SHIFT (1 << 0) +#define RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT (1 << 1) + u8 CW_VAL; + u8 RATE_FALLBACK; + u8 reserved_16[25]; + u8 CONFIG5; + u8 TX_DMA_POLLING; + u8 reserved_17[2]; + __le16 CWR; + u8 RETRY_CTR; + u8 reserved_18[5]; + __le32 RDSAR; + u8 reserved_19[18]; + u16 TALLY_CNT; + u8 TALLY_SEL; +} __attribute__((packed)); + +static const struct ieee80211_rate rtl818x_rates[] = { + { .rate = 10, + .val = 0, + .flags = IEEE80211_RATE_CCK }, + { .rate = 20, + .val = 1, + .flags = IEEE80211_RATE_CCK }, + { .rate = 55, + .val = 2, + .flags = IEEE80211_RATE_CCK }, + { .rate = 110, + .val = 3, + .flags = IEEE80211_RATE_CCK }, + { .rate = 60, + .val = 4, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 90, + .val = 5, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 120, + .val = 6, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 180, + .val = 7, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 240, + .val = 8, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 360, + .val = 9, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 480, + .val = 10, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 540, + .val = 11, + .flags = IEEE80211_RATE_OFDM }, +}; + +static const struct ieee80211_channel rtl818x_channels[] = { + { .chan = 1, + .freq = 2412}, + { .chan = 2, + .freq = 2417}, + { .chan = 3, + .freq = 2422}, + { .chan = 4, + .freq = 2427}, + { .chan = 5, + .freq = 2432}, + { .chan = 6, + .freq = 2437}, + { .chan = 7, + .freq = 2442}, + { .chan = 8, + .freq = 2447}, + { .chan = 9, + .freq = 2452}, + { .chan = 10, + .freq = 2457}, + { .chan = 11, + .freq = 2462}, + { .chan = 12, + .freq = 2467}, + { .chan = 13, + .freq = 2472}, + { .chan = 14, + .freq = 2484} +}; + +#endif /* RTL818X_H */ - To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
