This patch provides Makefile and KConfig for the WiMAX stack,
integrating them into the networking stack's Makefile, Kconfig and
doc-book templates.
Signed-off-by: Inaky Perez-Gonzalez <inaky@xxxxxxxxxxxxxxx>
---
Documentation/DocBook/networking.tmpl | 8 +++++++
net/Kconfig | 2 +
net/Makefile | 1 +
net/wimax/Kconfig | 36 +++++++++++++++++++++++++++++++++
net/wimax/Makefile | 12 +++++++++++
5 files changed, 59 insertions(+), 0 deletions(-)
create mode 100644 net/wimax/Kconfig
create mode 100644 net/wimax/Makefile
diff --git a/Documentation/DocBook/networking.tmpl b/Documentation/DocBook/networking.tmpl
index f24f9e8..7053c1c 100644
--- a/Documentation/DocBook/networking.tmpl
+++ b/Documentation/DocBook/networking.tmpl
@@ -101,6 +101,14 @@ X!Enet/core/wireless.c
<sect1><title>Synchronous PPP</title>
!Edrivers/net/wan/syncppp.c
</sect1>
+ <sect1><title>WiMAX</title>
+!Enet/wimax/op-msg.c
+!Enet/wimax/op-reset.c
+!Enet/wimax/op-rfkill.c
+!Enet/wimax/stack.c
+!Iinclude/net/wimax.h
+!Iinclude/linux/wimax.h
+ </sect1>
</chapter>
</book>
diff --git a/net/Kconfig b/net/Kconfig
index d789d79..3bff221 100644
--- a/net/Kconfig
+++ b/net/Kconfig
@@ -251,6 +251,8 @@ source "net/ieee80211/Kconfig"
endif # WIRELESS
+source "net/wimax/Kconfig"
+
source "net/rfkill/Kconfig"
source "net/9p/Kconfig"
diff --git a/net/Makefile b/net/Makefile
index 27d1f10..620a505 100644
--- a/net/Makefile
+++ b/net/Makefile
@@ -61,3 +61,4 @@ obj-$(CONFIG_NET_9P) += 9p/
ifeq ($(CONFIG_NET),y)
obj-$(CONFIG_SYSCTL) += sysctl_net.o
endif
+obj-$(CONFIG_WIMAX) += wimax/
diff --git a/net/wimax/Kconfig b/net/wimax/Kconfig
new file mode 100644
index 0000000..67d5f4d
--- /dev/null
+++ b/net/wimax/Kconfig
@@ -0,0 +1,36 @@
+#
+# WiMAX LAN device configuration
+#
+
+menuconfig WIMAX
+ tristate "WiMAX Wireless Broadband support"
+ help
+
+ Select to configure support for devices that provide wireless
+ broadband connectivity using the WiMAX protocol (IEEE 802.16).
+
+ Please note that most of these devices require signing up for
+ a service plan with a provider.
+
+ The different WiMAX drivers can be enabled in the menu entry
+
+ Device Drivers > Network device support > WiMAX Wireless Broadband devices
+
+ If unsure, it is safe to select M (module).
+
+config WIMAX_DEBUG_LEVEL
+ int "WiMAX debug level"
+ depends on WIMAX
+ default 8
+ help
+
+ Select the maximum debug verbosity level to be compiled into
+ the WiMAX stack code.
+
+ By default, debug messages are disabled at runtime and can be
+ selectively enabled for different parts of the code using the
+ sysfs debug-levels file.
+
+ If set at zero, this will compile out all the debug code.
+
+ It is recommended that it is left at 8.
diff --git a/net/wimax/Makefile b/net/wimax/Makefile
new file mode 100644
index 0000000..22d5a28
--- /dev/null
+++ b/net/wimax/Makefile
@@ -0,0 +1,12 @@
+
+obj-$(CONFIG_WIMAX) += wimax.o
+
+wimax-objs := \
+ id-table.o \
+ op-msg.o \
+ op-open.o \
+ op-reset.o \
+ op-rfkill.o \
+ stack.o
+
+
--
1.5.6.5
