The Raspberry Pi 400 is like a Pi 4 B designed into a keyboard. But there
are some minor differences:
- higher CPU clock rate (1.8 GHz)
- different Wifi chip (BCM43456)
- power off is now handled via GPIO
- no ACT LED
Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/bcm2711-rpi-400.dts | 271 ++++++++++++++++++++++++++++++++++
2 files changed, 272 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm2711-rpi-400.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f8f09c5..ec00dba 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -88,6 +88,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
bcm2837-rpi-cm3-io3.dtb \
+ bcm2711-rpi-400.dtb \
bcm2711-rpi-4-b.dtb \
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
diff --git a/arch/arm/boot/dts/bcm2711-rpi-400.dts b/arch/arm/boot/dts/bcm2711-rpi-400.dts
new file mode 100644
index 0000000..f063c5e
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2711-rpi-400.dts
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-usb-peripheral.dtsi"
+
+/ {
+ compatible = "raspberrypi,400", "brcm,bcm2711";
+ model = "Raspberry Pi 400";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ /* Will be filled by the bootloader */
+ memory@0 {
+ device_type = "memory";
+ reg = <0 0 0>;
+ };
+
+ aliases {
+ ethernet0 = &genet;
+ };
+
+ leds {
+ /delete-node/ act;
+
+ led-pwr {
+ label = "PWR";
+ gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&expgpio 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ sd_io_1v8_reg: sd_io_1v8_reg {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-sd-io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-settling-time-us = <5000>;
+ gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ status = "okay";
+ };
+
+ sd_vcc_reg: sd_vcc_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ddc0 {
+ status = "okay";
+};
+
+&ddc1 {
+ status = "okay";
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "",
+ "GLOBAL_RESET",
+ "VDD_SD_IO_SEL",
+ "CAM_GPIO",
+ "SD_PWR_ON",
+ "SD_OC_N";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "RGMII_MDIO",
+ "RGMIO_MDC",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ /* Shared with SPI flash */
+ "PWM0_MISO",
+ "PWM1_MOSI",
+ "STATUS_LED_G_CLK",
+ "SPIFLASH_CE_N",
+ "SDA0",
+ "SCL0",
+ "RGMII_RXCLK",
+ "RGMII_RXCTL",
+ "RGMII_RXD0",
+ "RGMII_RXD1",
+ "RGMII_RXD2",
+ "RGMII_RXD3",
+ "RGMII_TXCLK",
+ "RGMII_TXCTL",
+ "RGMII_TXD0",
+ "RGMII_TXD1",
+ "RGMII_TXD2",
+ "RGMII_TXD3";
+};
+
+&hdmi0 {
+ status = "okay";
+};
+
+&hdmi1 {
+ status = "okay";
+};
+
+&pixelvalve0 {
+ status = "okay";
+};
+
+&pixelvalve1 {
+ status = "okay";
+};
+
+&pixelvalve2 {
+ status = "okay";
+};
+
+&pixelvalve4 {
+ status = "okay";
+};
+
+&pm {
+ /delete-property/ system-power-controller;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* EMMC2 is used to drive the SD card */
+&emmc2 {
+ vqmmc-supply = <&sd_io_1v8_reg>;
+ vmmc-supply = <&sd_vcc_reg>;
+ broken-cd;
+ status = "okay";
+};
+
+&genet {
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii-rxid";
+ status = "okay";
+};
+
+&genet_mdio {
+ clock-frequency = <1950000>;
+
+ phy1: ethernet-phy@1 {
+ /* No PHY interrupt */
+ reg = <0x1>;
+ };
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
+
+&vc4 {
+ status = "okay";
+};
+
+&vec {
+ status = "disabled";
+};
--
2.7.4
