On Thu, May 30, 2024 at 9:09 PM Michael S. Tsirkin <mst@xxxxxxxxxx> wrote:
>
> On Thu, May 30, 2024 at 06:29:51PM +0800, Jason Wang wrote:
> > On Thu, May 30, 2024 at 2:10 PM Michael S. Tsirkin <mst@xxxxxxxxxx> wrote:
> > >
> > > On Thu, May 30, 2024 at 11:20:55AM +0800, Jason Wang wrote:
> > > > This patch synchronize operstate with admin state per RFC2863.
> > > >
> > > > This is done by trying to toggle the carrier upon open/close and
> > > > synchronize with the config change work. This allows propagate status
> > > > correctly to stacked devices like:
> > > >
> > > > ip link add link enp0s3 macvlan0 type macvlan
> > > > ip link set link enp0s3 down
> > > > ip link show
> > > >
> > > > Before this patch:
> > > >
> > > > 3: enp0s3: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
> > > > link/ether 00:00:05:00:00:09 brd ff:ff:ff:ff:ff:ff
> > > > ......
> > > > 5: macvlan0@enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
> > > > link/ether b2:a9:c5:04:da:53 brd ff:ff:ff:ff:ff:ff
> > > >
> > > > After this patch:
> > > >
> > > > 3: enp0s3: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
> > > > link/ether 00:00:05:00:00:09 brd ff:ff:ff:ff:ff:ff
> > > > ...
> > > > 5: macvlan0@enp0s3: <NO-CARRIER,BROADCAST,MULTICAST,UP,M-DOWN> mtu 1500 qdisc noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
> > > > link/ether b2:a9:c5:04:da:53 brd ff:ff:ff:ff:ff:ff
> > > >
> > > > Cc: Venkat Venkatsubra <venkat.x.venkatsubra@xxxxxxxxxx>
> > > > Cc: Gia-Khanh Nguyen <gia-khanh.nguyen@xxxxxxxxxx>
> > > > Reviewed-by: Xuan Zhuo <xuanzhuo@xxxxxxxxxxxxxxxxx>
> > > > Acked-by: Michael S. Tsirkin <mst@xxxxxxxxxx>
> > > > Signed-off-by: Jason Wang <jasowang@xxxxxxxxxx>
> > > > ---
> > > > Changes since V1:
> > > > - rebase
> > > > - add ack/review tags
> > >
> > >
> > >
> > >
> > >
> > > > ---
> > > > drivers/net/virtio_net.c | 94 +++++++++++++++++++++++++++-------------
> > > > 1 file changed, 63 insertions(+), 31 deletions(-)
> > > >
> > > > diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> > > > index 4a802c0ea2cb..69e4ae353c51 100644
> > > > --- a/drivers/net/virtio_net.c
> > > > +++ b/drivers/net/virtio_net.c
> > > > @@ -433,6 +433,12 @@ struct virtnet_info {
> > > > /* The lock to synchronize the access to refill_enabled */
> > > > spinlock_t refill_lock;
> > > >
> > > > + /* Is config change enabled? */
> > > > + bool config_change_enabled;
> > > > +
> > > > + /* The lock to synchronize the access to config_change_enabled */
> > > > + spinlock_t config_change_lock;
> > > > +
> > > > /* Work struct for config space updates */
> > > > struct work_struct config_work;
> > > >
> > >
> > >
> > > But we already have dev->config_lock and dev->config_enabled.
> > >
> > > And it actually works better - instead of discarding config
> > > change events it defers them until enabled.
> > >
> >
> > Yes but then both virtio-net driver and virtio core can ask to enable
> > and disable and then we need some kind of synchronization which is
> > non-trivial.
>
> Well for core it happens on bring up path before driver works
> and later on tear down after it is gone.
> So I do not think they ever do it at the same time.
For example, there could be a suspend/resume when the admin state is down.
>
>
> > And device enabling on the core is different from bringing the device
> > up in the networking subsystem. Here we just delay to deal with the
> > config change interrupt on ndo_open(). (E.g try to ack announce is
> > meaningless when the device is down).
> >
> > Thanks
>
> another thing is that it is better not to re-read all config
> on link up if there was no config interrupt - less vm exits.
Yes, but it should not matter much as it's done in the ndo_open().
Thanks
>
> --
> MST
>
