Re: [virtio-comment] Re: virtio-sound: release control request clarification

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Anton,

thanks for the response. I added some inline comments.

On Wed, Oct 18, 2023 at 10:06:05AM +0900, Anton Yakovlev wrote:
> Hi Matias,
> 
> 
> On 18.10.2023 00:19, Matias Ezequiel Vara Larsen wrote:
> > Hello,
> > 
> > This email is to clarify the VirtIO specification regarding the RELEASE
> > control request. Section 5.14.6.6.5.1 [1] states the following device
> > requirements for the RELEASE control request:
> > 1. The device MUST complete all pending I/O messages for the specified
> > stream ID.
> > 2. The device MUST NOT complete the control request while there are
> > pending I/O messages for the specified stream ID.
> > 
> > The 1) requirement does not indicate what "complete" means. Does it mean
> > that the pending I/O messages in the tx queue shall be outputted in the
> > host, i.e., consumed by the audio backend? Or, completion means simply
> > to put the requests in the used-ring without consuming them?
> 
> Here "to complete" means moving the buffers to the used list in vring.
> Technically, the specification only requires that the device "return" all
> referenced DMA memory to the guest before completing the RELEASE control
> request. What the device actually does with these I/O messages is
> implementation dependent and is not within the scope of the specification.
> Thus...
> 
> 

Thank you, I got it. If I correctly understand you, after RELEASE is
issued, the specs specify only that the device should "return" all
buffers or "complete" them. Device implementations MAY or MAY NOT
playback them. In other words, the specification does not specify if
consumption should occur. I had interpreted this to mean that the guest
intended to output those buffers, leaving the device implementation with
no option but to do so.

> > Regarding 2), I interpret it as "the device shall wait until all I/O
> > messages are proceeded to complete the RELEASE control request".
> 
> ...you can do this way if you really need to.
> 
> 
> > Currently, the kernel driver seems not expecting such a delay when the
> > RELEASE command is sent. If I understand correctly, the kernel driver
> > first sends the RELEASE command and waits a fixed amount of time until
> > the device can process it. Then, the driver waits a fixed amount of time
> > until all pending IO messages are completed. If the device follows the
> > specification and waits until all messages IO are completed to issue the
> > completion of the RELEASE command, the kernel driver may timeout. The
> > time to complete N IO messages in the TX queue could be proportional
> > with the number of pending messages.
> 
> The default timeout for control requests in the ALSA driver is 1 second. In
> theory, this time should be enough to completely reproduce/fill the 500ms
> buffer, and complete all requests, including the RELEASE control request. If
> the device fails to do this, then most likely there are some problems with the
> implementation.
> 

Thanks for clarifying. Sorry to repeat myself, the point I want to make
is that the virtsnd_pcm_sync_stop() function that sends the RELEASE
control request uses virtsnd_ctl_msg_send_sync(). Message timeouts are
set up by the "msg_timeout_ms" module parameter. The timeout is the same
as for other control requests, such as SET_PARAM and PREPARE, but these
commands do not require flushing a queue, so I wondered how the timeout
could be the same.

> 
> > In our device implementation [2], RELEASE is handled as follows:
> > - Drop all messages in the TX queue without outputting in the host.
> > - Complete the RELEASE control request.
> > 
> > This seems to be working, however, I can observe that sometimes there
> > are still requests in the TX queue when we get RELEASE. Those requests
> > are never reproduced in the host.
> > 
> > My questions are:
> > - In the specification, should we modify it to clarify that all pending
> >    IO messages in the device are discarded during RELEASE, that is, not
> >    output to the host, but signaled to the guest as completed?
> 
> No, we shouldn't. See comment above.
> 
> 
> > - According to the specification, should the driver wait in RELEASE an
> >    amount of time proportional to the number of periods yet to be
> >    reproduced?
> 
> This is purely a matter of driver implementation. It is possible to implement
> the driver without timeouts, but this would be a bad idea. Because bugs in the
> device could lead to an infinite wait in the kernel.
> 
> 

I agree, thanks.

Matias.

> Best regards,
> 
> > 
> > Thanks, Matias.
> > 
> > [1]
> > https://ddec1-0-en-ctp.trendmicro.com:443/wis/clicktime/v1/query?url=https%3a%2f%2fdocs.oasis%2dopen.org%2fvirtio%2fvirtio%2fv1.2%2fcsd01%2fvirtio%2dv1.2%2dcsd01.html&umid=31e1136e-6322-4698-9f1d-d631ac36403e&auth=53c7c7de28b92dfd96e93d9dd61a23e634d2fbec-586f0596c89224a3bc9e20df81eaea8933bb129a
> > [2]
> > https://github.com/rust-vmm/vhost-device/tree/main/staging/vhost-device-sound
> 
> -- 
> Anton Yakovlev
> Senior Software Engineer
> 
> OpenSynergy GmbH
> Rotherstr. 20, 10245 Berlin
> 
> This publicly archived list offers a means to provide input to the
> OASIS Virtual I/O Device (VIRTIO) TC.
> 
> In order to verify user consent to the Feedback License terms and
> to minimize spam in the list archive, subscription is required
> before posting.
> 
> Subscribe: virtio-comment-subscribe@xxxxxxxxxxxxxxxxxxxx
> Unsubscribe: virtio-comment-unsubscribe@xxxxxxxxxxxxxxxxxxxx
> List help: virtio-comment-help@xxxxxxxxxxxxxxxxxxxx
> List archive: https://lists.oasis-open.org/archives/virtio-comment/
> Feedback License: https://www.oasis-open.org/who/ipr/feedback_license.pdf
> List Guidelines: https://www.oasis-open.org/policies-guidelines/mailing-lists
> Committee: https://www.oasis-open.org/committees/virtio/
> Join OASIS: https://www.oasis-open.org/join/
> 

_______________________________________________
Virtualization mailing list
Virtualization@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linuxfoundation.org/mailman/listinfo/virtualization



[Index of Archives]     [KVM Development]     [Libvirt Development]     [Libvirt Users]     [CentOS Virtualization]     [Netdev]     [Ethernet Bridging]     [Linux Wireless]     [Kernel Newbies]     [Security]     [Linux for Hams]     [Netfilter]     [Bugtraq]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux RAID]     [Linux Admin]     [Samba]

  Powered by Linux