On 10/12/2023 7:49 PM, Jason Wang wrote:
On Tue, Oct 10, 2023 at 5:05 PM Si-Wei Liu <si-wei.liu@xxxxxxxxxx> wrote:
Device specific IOMMU parent driver who wishes to see mapping to be
decoupled from virtio or vdpa device life cycle (device reset) can use
it to restore memory mapping in the device IOMMU to the initial or
default state. The reset of mapping is done per address space basis.
The reason why a separate .reset_map op is introduced is because this
allows a simple on-chip IOMMU model without exposing too much device
implementation details to the upper vdpa layer. The .dma_map/unmap or
.set_map driver API is meant to be used to manipulate the IOTLB mappings,
and has been abstracted in a way similar to how a real IOMMU device maps
or unmaps pages for certain memory ranges. However, apart from this there
also exists other mapping needs, in which case 1:1 passthrough mapping
has to be used by other users (read virtio-vdpa). To ease parent/vendor
driver implementation and to avoid abusing DMA ops in an unexpacted way,
these on-chip IOMMU devices can start with 1:1 passthrough mapping mode
initially at the he time of creation. Then the .reset_map op can be used
to switch iotlb back to this initial state without having to expose a
complex two-dimensional IOMMU device model.
Signed-off-by: Si-Wei Liu <si-wei.liu@xxxxxxxxxx>
---
include/linux/vdpa.h | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/include/linux/vdpa.h b/include/linux/vdpa.h
index d376309..26ae6ae 100644
--- a/include/linux/vdpa.h
+++ b/include/linux/vdpa.h
@@ -327,6 +327,15 @@ struct vdpa_map_file {
* @iova: iova to be unmapped
* @size: size of the area
* Returns integer: success (0) or error (< 0)
+ * @reset_map: Reset device memory mapping to the default
+ * state (optional)
I think we need to mention that this is a must for parents that use set_map()?
It's not a must IMO, some .set_map() user for e.g. VDUSE or vdpa-sim-blk
can deliberately choose to implement .reset_map() depending on its own
need. Those user_va software devices mostly don't care about mapping
cost during reset, as they don't have to pin kernel memory in general.
It's just whether or not they care about mapping being decoupled from
device reset at all.
And the exact implementation requirement of this interface has been
documented right below.
-Siwei
Other than this:
Acked-by: Jason Wang <jasowang@xxxxxxxxxx>
Thanks
+ * Needed for devices that are using device
+ * specific DMA translation and prefer mapping
+ * to be decoupled from the virtio life cycle,
+ * i.e. device .reset op does not reset mapping
+ * @vdev: vdpa device
+ * @asid: address space identifier
+ * Returns integer: success (0) or error (< 0)
* @get_vq_dma_dev: Get the dma device for a specific
* virtqueue (optional)
* @vdev: vdpa device
@@ -405,6 +414,7 @@ struct vdpa_config_ops {
u64 iova, u64 size, u64 pa, u32 perm, void *opaque);
int (*dma_unmap)(struct vdpa_device *vdev, unsigned int asid,
u64 iova, u64 size);
+ int (*reset_map)(struct vdpa_device *vdev, unsigned int asid);
int (*set_group_asid)(struct vdpa_device *vdev, unsigned int group,
unsigned int asid);
struct device *(*get_vq_dma_dev)(struct vdpa_device *vdev, u16 idx);
--
1.8.3.1
_______________________________________________
Virtualization mailing list
Virtualization@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linuxfoundation.org/mailman/listinfo/virtualization
