On Mon, Jul 26, 2021 at 5:17 PM Stefan Hajnoczi <stefanha@xxxxxxxxxx> wrote: > > On Thu, Jul 22, 2021 at 05:04:57PM +0800, Jason Wang wrote: > > > > 在 2021/7/21 下午5:41, Stefan Hajnoczi 写道: > > > On Wed, Jul 21, 2021 at 11:29:55AM +0800, Jason Wang wrote: > > > > 在 2021/7/14 上午12:19, Stefan Hajnoczi 写道: > > > > > These patches are not polished yet but I would like request feedback on this > > > > > approach and share performance results with you. > > > > > > > > > > Idle CPUs tentatively enter a busy wait loop before halting when the cpuidle > > > > > haltpoll driver is enabled inside a virtual machine. This reduces wakeup > > > > > latency for events that occur soon after the vCPU becomes idle. > > > > > > > > > > This patch series extends the cpuidle busy wait loop with the new poll_source > > > > > API so drivers can participate in polling. Such polling-aware drivers disable > > > > > their device's irq during the busy wait loop to avoid the cost of interrupts. > > > > > This reduces latency further than regular cpuidle haltpoll, which still relies > > > > > on irqs. > > > > > > > > > > Virtio drivers are modified to use the poll_source API so all virtio device > > > > > types get this feature. The following virtio-blk fio benchmark results show the > > > > > improvement: > > > > > > > > > > IOPS (numjobs=4, iodepth=1, 4 virtqueues) > > > > > before poll_source io_poll > > > > > 4k randread 167102 186049 (+11%) 186654 (+11%) > > > > > 4k randwrite 162204 181214 (+11%) 181850 (+12%) > > > > > 4k randrw 159520 177071 (+11%) 177928 (+11%) > > > > > > > > > > The comparison against io_poll shows that cpuidle poll_source achieves > > > > > equivalent performance to the block layer's io_poll feature (which I > > > > > implemented in a separate patch series [1]). > > > > > > > > > > The advantage of poll_source is that applications do not need to explicitly set > > > > > the RWF_HIPRI I/O request flag. The poll_source approach is attractive because > > > > > few applications actually use RWF_HIPRI and it takes advantage of CPU cycles we > > > > > would have spent in cpuidle haltpoll anyway. > > > > > > > > > > The current series does not improve virtio-net. I haven't investigated deeply, > > > > > but it is possible that NAPI and poll_source do not combine. See the final > > > > > patch for a starting point on making the two work together. > > > > > > > > > > I have not tried this on bare metal but it might help there too. The cost of > > > > > disabling a device's irq must be less than the savings from avoiding irq > > > > > handling for this optimization to make sense. > > > > > > > > > > [1] https://lore.kernel.org/linux-block/20210520141305.355961-1-stefanha@xxxxxxxxxx/ > > > > > > > > Hi Stefan: > > > > > > > > Some questions: > > > > > > > > 1) What's the advantages of introducing polling at virtio level instead of > > > > doing it at each subsystems? Polling in virtio level may only work well if > > > > all (or most) of the devices are virtio > > > I'm not sure I understand the question. cpuidle haltpoll benefits all > > > devices today, except it incurs interrupt latency. The poll_source API > > > eliminates the interrupt latency for drivers that can disable device > > > interrupts cheaply. > > > > > > This patch adds poll_source to core virtio code so that all virtio > > > drivers get this feature for free. No driver-specific changes are > > > needed. > > > > > > If you mean networking, block layer, etc by "subsystems" then there's > > > nothing those subsystems can do to help. Whether poll_source can be used > > > depends on the specific driver, not the subsystem. If you consider > > > drivers/virtio/ a subsystem, then that's exactly what the patch series > > > is doing. > > > > > > I meant, if we choose to use idle poll, we have some several choices: > > > > 1) bus level (e.g the virtio) > > 2) subsystem level (e.g the networking and block) > > > > I'm not sure which one is better. > > This API is intended to be driver- or bus-level. I don't think > subsystems can do very much since they don't know the hardware > capabilities (cheap interrupt disabling) and in most cases there's no > advantage of plumbing it through subsystems when drivers can call the > API directly. > > > > > 2) What's the advantages of using cpuidle instead of using a thread (and > > > > leverage the scheduler)? > > > In order to combine with the existing cpuidle infrastructure. No new > > > polling loop is introduced and no additional CPU cycles are spent on > > > polling. > > > > > > If cpuidle itself is converted to threads then poll_source would > > > automatically operate in a thread too, but this patch series doesn't > > > change how the core cpuidle code works. > > > > > > So networking subsystem can use NAPI busy polling in the process context > > which means it can be leveraged by the scheduler. > > > > I'm not sure it's a good idea to poll drivers for a specific bus in the > > general cpu idle layer. > > Why? Maybe because the cpuidle execution environment is a little special? Well, this would be prone to abuse. The time spent in that driver callback counts as CPU idle time while it really is the driver running and there is not limit on how much time the callback can take, while doing costly things in the idle loop is generally avoided, because on wakeup the CPU needs to be available to the task needing it as soon as possible. IOW, the callback potentially add unbounded latency to the CPU wakeup path. _______________________________________________ Virtualization mailing list Virtualization@xxxxxxxxxxxxxxxxxxxxxxxxxx https://lists.linuxfoundation.org/mailman/listinfo/virtualization
