On 2021/2/10 上午8:26, Si-Wei Liu wrote:
On 2/8/2021 7:37 PM, Jason Wang wrote:
On 2021/2/6 下午8:29, Si-Wei Liu wrote:
While virtq is stopped, get_vq_state() is supposed to
be called to get sync'ed with the latest internal
avail_index from device. The saved avail_index is used
to restate the virtq once device is started. Commit
b35ccebe3ef7 introduced the clear_virtqueues() routine
to reset the saved avail_index, however, the index
gets cleared a bit earlier before get_vq_state() tries
to read it. This would cause consistency problems when
virtq is restarted, e.g. through a series of link down
and link up events. We could defer the clearing of
avail_index to until the device is to be started,
i.e. until VIRTIO_CONFIG_S_DRIVER_OK is set again in
set_status().
Fixes: b35ccebe3ef7 ("vdpa/mlx5: Restore the hardware used index
after change map")
Signed-off-by: Si-Wei Liu <si-wei.liu@xxxxxxxxxx>
---
drivers/vdpa/mlx5/net/mlx5_vnet.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/vdpa/mlx5/net/mlx5_vnet.c
b/drivers/vdpa/mlx5/net/mlx5_vnet.c
index aa6f8cd..444ab58 100644
--- a/drivers/vdpa/mlx5/net/mlx5_vnet.c
+++ b/drivers/vdpa/mlx5/net/mlx5_vnet.c
@@ -1785,7 +1785,6 @@ static void mlx5_vdpa_set_status(struct
vdpa_device *vdev, u8 status)
if (!status) {
mlx5_vdpa_info(mvdev, "performing device reset\n");
teardown_driver(ndev);
- clear_virtqueues(ndev);
mlx5_vdpa_destroy_mr(&ndev->mvdev);
ndev->mvdev.status = 0;
++mvdev->generation;
@@ -1794,6 +1793,7 @@ static void mlx5_vdpa_set_status(struct
vdpa_device *vdev, u8 status)
if ((status ^ ndev->mvdev.status) &
VIRTIO_CONFIG_S_DRIVER_OK) {
if (status & VIRTIO_CONFIG_S_DRIVER_OK) {
+ clear_virtqueues(ndev);
Rethink about this. As mentioned in another thread, this in fact
breaks set_vq_state(). (See vhost_virtqueue_start() ->
vhost_vdpa_set_vring_base() in qemu codes).
I assume that the clearing for vhost-vdpa would be done via (qemu code),
vhost_dev_start()->vhost_vdpa_dev_start()->vhost_vdpa_call(status |
VIRTIO_CONFIG_S_DRIVER_OK)
which is _after_ vhost_virtqueue_start() gets called to restore the
avail_idx to h/w in vhost_dev_start(). What am I missing here?
-Siwei
I think not. I thought clear_virtqueues() will clear hardware index but
looks not. (I guess we need a better name other than clear_virtqueues(),
e.g from the name it looks like the it will clear the hardware states)
Thanks
The issue is that the avail idx is forgot, we need keep it.
Thanks
err = setup_driver(ndev);
if (err) {
mlx5_vdpa_warn(mvdev, "failed to setup driver\n");
_______________________________________________
Virtualization mailing list
Virtualization@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linuxfoundation.org/mailman/listinfo/virtualization
