On 2019/9/10 下午6:01, Michael S. Tsirkin wrote:
+#ifndef _LINUX_VIRTIO_MDEV_H
+#define _LINUX_VIRTIO_MDEV_H
+
+#include <linux/interrupt.h>
+#include <linux/vringh.h>
+#include <uapi/linux/virtio_net.h>
+
+/*
+ * Ioctls
+ */
Pls add a bit more content here. It's redundant to state these
are ioctls. Much better to document what does each one do.
Ok.
+
+struct virtio_mdev_callback {
+ irqreturn_t (*callback)(void *);
+ void *private;
+};
+
+#define VIRTIO_MDEV 0xAF
+#define VIRTIO_MDEV_SET_VQ_CALLBACK _IOW(VIRTIO_MDEV, 0x00, \
+ struct virtio_mdev_callback)
+#define VIRTIO_MDEV_SET_CONFIG_CALLBACK _IOW(VIRTIO_MDEV, 0x01, \
+ struct virtio_mdev_callback)
Function pointer in an ioctl parameter? How does this ever make sense?
I admit this is hacky (casting).
And can't we use a couple of registers for this, and avoid ioctls?
Yes, how about something like interrupt numbers for each virtqueue and
config?
+
+#define VIRTIO_MDEV_DEVICE_API_STRING "virtio-mdev"
+
+/*
+ * Control registers
+ */
+
+/* Magic value ("virt" string) - Read Only */
+#define VIRTIO_MDEV_MAGIC_VALUE 0x000
+
+/* Virtio device version - Read Only */
+#define VIRTIO_MDEV_VERSION 0x004
+
+/* Virtio device ID - Read Only */
+#define VIRTIO_MDEV_DEVICE_ID 0x008
+
+/* Virtio vendor ID - Read Only */
+#define VIRTIO_MDEV_VENDOR_ID 0x00c
+
+/* Bitmask of the features supported by the device (host)
+ * (32 bits per set) - Read Only */
+#define VIRTIO_MDEV_DEVICE_FEATURES 0x010
+
+/* Device (host) features set selector - Write Only */
+#define VIRTIO_MDEV_DEVICE_FEATURES_SEL 0x014
+
+/* Bitmask of features activated by the driver (guest)
+ * (32 bits per set) - Write Only */
+#define VIRTIO_MDEV_DRIVER_FEATURES 0x020
+
+/* Activated features set selector - Write Only */
+#define VIRTIO_MDEV_DRIVER_FEATURES_SEL 0x024
+
+/* Queue selector - Write Only */
+#define VIRTIO_MDEV_QUEUE_SEL 0x030
+
+/* Maximum size of the currently selected queue - Read Only */
+#define VIRTIO_MDEV_QUEUE_NUM_MAX 0x034
+
+/* Queue size for the currently selected queue - Write Only */
+#define VIRTIO_MDEV_QUEUE_NUM 0x038
+
+/* Ready bit for the currently selected queue - Read Write */
+#define VIRTIO_MDEV_QUEUE_READY 0x044
Is this same as started?
Do you mean "status"?
+
+/* Alignment of virtqueue - Read Only */
+#define VIRTIO_MDEV_QUEUE_ALIGN 0x048
+
+/* Queue notifier - Write Only */
+#define VIRTIO_MDEV_QUEUE_NOTIFY 0x050
+
+/* Device status register - Read Write */
+#define VIRTIO_MDEV_STATUS 0x060
+
+/* Selected queue's Descriptor Table address, 64 bits in two halves */
+#define VIRTIO_MDEV_QUEUE_DESC_LOW 0x080
+#define VIRTIO_MDEV_QUEUE_DESC_HIGH 0x084
+
+/* Selected queue's Available Ring address, 64 bits in two halves */
+#define VIRTIO_MDEV_QUEUE_AVAIL_LOW 0x090
+#define VIRTIO_MDEV_QUEUE_AVAIL_HIGH 0x094
+
+/* Selected queue's Used Ring address, 64 bits in two halves */
+#define VIRTIO_MDEV_QUEUE_USED_LOW 0x0a0
+#define VIRTIO_MDEV_QUEUE_USED_HIGH 0x0a4
+
+/* Configuration atomicity value */
+#define VIRTIO_MDEV_CONFIG_GENERATION 0x0fc
+
+/* The config space is defined by each driver as
+ * the per-driver configuration space - Read Write */
+#define VIRTIO_MDEV_CONFIG 0x100
Mixing device and generic config space is what virtio pci did,
caused lots of problems with extensions.
It would be better to reserve much more space.
I see, will do this.
Thanks
+
+#endif
+
+
+/* Ready bit for the currently selected queue - Read Write */
--
2.19.1
_______________________________________________
Virtualization mailing list
Virtualization@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linuxfoundation.org/mailman/listinfo/virtualization
