Changes since v2: - Rebased on 3.13-rc1 - Fix braces in phy_get_bus_width()/phy_set_bus_width() - Drop generic phy conversion to use the same support from the Exynos generic phy conversion series - Modify dts support to match the "device" phy name required in the v3 Exynos generic phy conversion - Add s3c-hsotg phy_init/phy_exit support - Fix typo on reg property in kona phy binding - Replace phy driver reg struct with offset defines - Move phy soft reset to phy driver init - Fix dts node names to match ePAPR conventions Changes since v1: - Convert USB phy driver to generic phy subsystem - Add phy bus width apis - Drop dwc2 phy bus width DT property in favor of querying the phy provider for bus width - Add generic phy/clock properties to dwc2 DT binding - Add generic phy subsystem support to s3c-hsotg with the existing usb phy and pdata phy methods as a fallback - Split bindings out to separate patches to match the latest DT binding review guidelines This series adds USB Device Controller support for the Broadcom BCM281xx family of parts. BCM281xx contains a DWC2 OTG block and s3c-hsotg is used to support UDC operation. Part 1 adds phy bus width support to the generic phy subsystem Parts 2-6 allows s3c-hsotg to build on non-Samsung platforms, supports the dwc2 binding, adds phy_init/phy_exit support, and supports fetching phy bus width using the generic phy layer. Parts 7-8 add a generic phy binding and driver for the BCM Kona USB PHY. Part 9 adds the DT nodes to enable UDC support on both BCM281xx boards in the kernel. This series depends on: - "Update Kona drivers to use clocks" series https://lkml.org/lkml/2013/11/14/450 - "Add new Exynos USB 2.0 PHY driver" series https://lkml.org/lkml/2013/11/5/271 Matt Porter (9): phy: add phy_get_bus_width()/phy_set_bus_width() calls staging: dwc2: update DT binding to add generic clock/phy properties usb: gadget: s3c-hsotg: enable build for other platforms usb: gadget: s3c-hsotg: add snps,dwc2 compatible string usb: gadget: s3c-hsotg: use generic phy_init()/phy_exit() support usb: gadget: s3c-hsotg: get phy bus width from phy subsystem phy: add Broadcom Kona USB2 PHY DT binding phy: add Broadcom Kona USB2 PHY driver ARM: dts: add usb udc support to bcm281xx .../devicetree/bindings/phy/bcm-kona-usb2-phy.txt | 15 ++ Documentation/devicetree/bindings/staging/dwc2.txt | 10 ++ arch/arm/boot/dts/bcm11351-brt.dts | 6 + arch/arm/boot/dts/bcm11351.dtsi | 18 +++ arch/arm/boot/dts/bcm28155-ap.dts | 8 ++ drivers/phy/Kconfig | 6 + drivers/phy/Makefile | 1 + drivers/phy/phy-bcm-kona-usb2.c | 158 +++++++++++++++++++++ drivers/usb/gadget/Kconfig | 7 +- drivers/usb/gadget/s3c-hsotg.c | 22 ++- drivers/usb/gadget/s3c-hsotg.h | 1 + include/linux/phy/phy.h | 20 +++ 12 files changed, 265 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/phy/bcm-kona-usb2-phy.txt create mode 100644 drivers/phy/phy-bcm-kona-usb2.c -- 1.8.4 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
