RE: [RFC PATCH 2/5] phy: Add WIP Exynos 5250 support to the Exynos USB PHY driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Kishon,

> From: Kishon Vijay Abraham I [mailto:kishon@xxxxxx]
> Sent: Friday, October 25, 2013 5:44 PM
> 
> Hi,
> 
> On Friday 25 October 2013 07:45 PM, Kamil Debski wrote:
> > Add support for Exynos 5250. This is work-in-progress commit. Not for
> > merging.
> >
> > Signed-off-by: Kamil Debski <k.debski@xxxxxxxxxxx>
> > Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> > ---
> >  drivers/phy/Kconfig              |    7 +
> >  drivers/phy/Makefile             |    1 +
> >  drivers/phy/phy-exynos-usb.c     |   10 +
> >  drivers/phy/phy-exynos-usb.h     |    1 +
> >  drivers/phy/phy-exynos5250-usb.c |  411
> > ++++++++++++++++++++++++++++++++++++++
> >  5 files changed, 430 insertions(+)
> >  create mode 100644 drivers/phy/phy-exynos5250-usb.c
> >
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index
> > 2f7ac0a..0f598d0 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -36,4 +36,11 @@ config PHY_EXYNOS4212_USB
> >  	help
> >  	  Enable USB PHY support for Exynos 4212
> >
> > +config PHY_EXYNOS5250_USB
> > +	bool "Support for Exynos 5250"
> > +	depends on PHY_EXYNOS_USB
> 
> This should be a separate driver. Not necessary to use PHY_EXYNOS_USB.
> > +	depends on SOC_EXYNOS5250
> > +	help
> > +	  Enable USB PHY support for Exynos 5250
> > +
> >  endmenu
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index
> > ca3dc82..0dff0dd 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -6,3 +6,4 @@ obj-$(CONFIG_GENERIC_PHY)	+= phy-core.o
> >  obj-$(CONFIG_PHY_EXYNOS_USB)		+= phy-exynos-usb.o
> >  obj-$(CONFIG_PHY_EXYNOS4210_USB)	+= phy-exynos4210-usb.o
> >  obj-$(CONFIG_PHY_EXYNOS4212_USB)	+= phy-exynos4212-usb.o
> > +obj-$(CONFIG_PHY_EXYNOS5250_USB)	+= phy-exynos5250-usb.o
> > diff --git a/drivers/phy/phy-exynos-usb.c
> > b/drivers/phy/phy-exynos-usb.c index d4a26df..172b774 100644
> > --- a/drivers/phy/phy-exynos-usb.c
> > +++ b/drivers/phy/phy-exynos-usb.c
> > @@ -212,6 +212,10 @@ extern const struct uphy_config
> > exynos4210_uphy_config;  extern const struct uphy_config
> > exynos4212_uphy_config;  #endif
> >
> > +#ifdef CONFIG_PHY_EXYNOS5250_USB
> > +extern const struct uphy_config exynos5250_uphy_config; #endif
> > +
> >  static const struct of_device_id exynos_uphy_of_match[] = {  #ifdef
> > CONFIG_PHY_EXYNOS4210_USB
> >  	{
> > @@ -225,6 +229,12 @@ static const struct of_device_id
> exynos_uphy_of_match[] = {
> >  		.data = &exynos4212_uphy_config,
> >  	},
> >  #endif
> > +#ifdef CONFIG_PHY_EXYNOS5250_USB
> > +	{
> > +		.compatible = "samsung,exynos5250-usbphy",
> > +		.data = &exynos5250_uphy_config,
> > +	},
> > +#endif
> >  	{ },
> >  };
> >
> > diff --git a/drivers/phy/phy-exynos-usb.h
> > b/drivers/phy/phy-exynos-usb.h index f45cb3c..a9febfa 100644
> > --- a/drivers/phy/phy-exynos-usb.h
> > +++ b/drivers/phy/phy-exynos-usb.h
> > @@ -42,6 +42,7 @@ enum samsung_cpu_type {
> >  	TYPE_S3C64XX,
> >  	TYPE_EXYNOS4210,
> >  	TYPE_EXYNOS4212,
> > +	TYPE_EXYNOS5250,
> 
> No cpu types here.
> >  };
> >
> >  enum uphy_state {
> > diff --git a/drivers/phy/phy-exynos5250-usb.c
> > b/drivers/phy/phy-exynos5250-usb.c
> > new file mode 100644
> > index 0000000..156093b
> > --- /dev/null
> > +++ b/drivers/phy/phy-exynos5250-usb.c
> > @@ -0,0 +1,411 @@
> > +/*
> > + * Samsung S5P/EXYNOS SoC series USB PHY driver
> > + *
> > + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> > + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > +modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_address.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/spinlock.h>
> > +#include "phy-exynos-usb.h"
> > +
> > +/* Exynos USB PHY registers */
> > +#define EXYNOS_5250_REFCLKSEL_CRYSTAL	0x0
> > +#define EXYNOS_5250_REFCLKSEL_XO	0x1
> > +#define EXYNOS_5250_REFCLKSEL_CLKCORE	0x2
> > +
> > +#define EXYNOS_5250_FSEL_9MHZ6		0x0
> > +#define EXYNOS_5250_FSEL_10MHZ		0x1
> > +#define EXYNOS_5250_FSEL_12MHZ		0x2
> > +#define EXYNOS_5250_FSEL_19MHZ2		0x3
> > +#define EXYNOS_5250_FSEL_20MHZ		0x4
> > +#define EXYNOS_5250_FSEL_24MHZ		0x5
> > +#define EXYNOS_5250_FSEL_50MHZ		0x7
> > +
> > +/* Normal host */
> > +#define EXYNOS_5250_HOSTPHYCTRL0			0x0
> > +
> > +#define EXYNOS_5250_HOSTPHYCTRL0_PHYSWRSTALL		(0x1 << 31)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_REFCLKSEL_SHIFT	19
> > +#define EXYNOS_5250_HOSTPHYCTRL0_REFCLKSEL_MASK	\
> > +		(0x3 << EXYNOS_5250_HOSTPHYCTRL0_REFCLKSEL_SHIFT)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_FSEL_SHIFT		16
> > +#define EXYNOS_5250_HOSTPHYCTRL0_FSEL_MASK \
> > +		(0x7 << EXYNOS_5250_HOSTPHYCTRL0_FSEL_SHIFT)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_TESTBURNIN		(0x1 << 11)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_RETENABLE		(0x1 << 10)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_COMMON_ON_N		(0x1 << 9)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_MASK		(0x3 << 7)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_DUAL		(0x0 << 7)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_ID0		(0x1 << 7)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_ANALOGTEST	(0x2 << 7)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_SIDDQ			(0x1 << 6)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_FORCESLEEP		(0x1 << 5)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_FORCESUSPEND		(0x1 << 4)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_WORDINTERFACE		(0x1 << 3)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_UTMISWRST		(0x1 << 2)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_LINKSWRST		(0x1 << 1)
> > +#define EXYNOS_5250_HOSTPHYCTRL0_PHYSWRST		(0x1 << 0)
> > +
> > +/* HSIC0 & HSCI1 */
> > +#define EXYNOS_5250_HOSTPHYCTRL1			0x10
> > +#define EXYNOS_5250_HOSTPHYCTRL2			0x20
> > +
> > +#define EXYNOS_5250_HOSTPHYCTRLX_REFCLKSEL_MASK		(0x3 << 23)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_REFCLKDIV_MASK		(0x7f << 16)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_SIDDQ			(0x1 << 6)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_FORCESLEEP		(0x1 << 5)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_FORCESUSPEND		(0x1 << 4)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_WORDINTERFACE		(0x1 << 3)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_UTMISWRST		(0x1 << 2)
> > +#define EXYNOS_5250_HOSTPHYCTRLX_PHYSWRST		(0x1 << 0)
> > +
> > +/* EHCI control */
> > +#define EXYNOS_5250_HOSTEHCICTRL			0x30
> > +#define EXYNOS_5250_HOSTEHCICTRL_ENAINCRXALIGN		(0x1 << 29)
> > +#define EXYNOS_5250_HOSTEHCICTRL_ENAINCR4		(0x1 << 28)
> > +#define EXYNOS_5250_HOSTEHCICTRL_ENAINCR8		(0x1 << 27)
> > +#define EXYNOS_5250_HOSTEHCICTRL_ENAINCR16		(0x1 << 26)
> > +#define EXYNOS_5250_HOSTEHCICTRL_AUTOPPDONOVRCUREN	(0x1 << 25)
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_SHIFT	19
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_MASK	\
> > +		(0x3f << EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_SHIFT)
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL1_SHIFT	13
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL1_MASK	\
> > +		(0x3f << EXYNOS_5250_HOSTEHCICTRL_FLADJVAL1_SHIFT)
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL2_SHIFT	7
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_MASK	\
> > +		(0x3f << EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_SHIFT)
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVALHOST_SHIFT	1
> > +#define EXYNOS_5250_HOSTEHCICTRL_FLADJVALHOST_MASK \
> > +		(0x1 << EXYNOS_5250_HOSTEHCICTRL_FLADJVALHOST_SHIFT)
> > +#define EXYNOS_5250_HOSTEHCICTRL_SIMULATIONMODE		(0x1 << 0)
> > +
> > +/* OHCI control */
> > +#define EXYNOS_5250_HOSTOHCICTRL                        0x34
> > +#define EXYNOS_5250_HOSTOHCICTRL_FRAMELENVAL_SHIFT	1
> > +#define EXYNOS_5250_HOSTOHCICTRL_FRAMELENVAL_MASK \
> > +		(0x3ff << EXYNOS_5250_HOSTOHCICTRL_FRAMELENVAL_SHIFT)
> > +#define EXYNOS_5250_HOSTOHCICTRL_FRAMELENVALEN		(0x1 << 0)
> > +
> > +/* USBOTG */
> > +#define EXYNOS_5250_USBOTGSYS				0x38
> > +#define EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET		(0x1 << 14)
> > +#define EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG		(0x1 << 13)
> > +#define EXYNOS_5250_USBOTGSYS_PHY_SW_RST		(0x1 << 12)
> > +#define EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT		9
> > +#define EXYNOS_5250_USBOTGSYS_REFCLKSEL_MASK \
> > +		(0x3 << EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT)
> > +#define EXYNOS_5250_USBOTGSYS_ID_PULLUP			(0x1 << 8)
> > +#define EXYNOS_5250_USBOTGSYS_COMMON_ON			(0x1 << 7)
> > +#define EXYNOS_5250_USBOTGSYS_FSEL_SHIFT		4
> > +#define EXYNOS_5250_USBOTGSYS_FSEL_MASK \
> > +		(0x3 << EXYNOS_5250_USBOTGSYS_FSEL_SHIFT)
> > +#define EXYNOS_5250_USBOTGSYS_FORCE_SLEEP		(0x1 << 3)
> > +#define EXYNOS_5250_USBOTGSYS_OTGDISABLE		(0x1 << 2)
> > +#define EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG		(0x1 << 1)
> > +#define EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND		(0x1 << 0)
> > +
> > +/* Isolation, configured in the power management unit */
> > +#define EXYNOS_5250_USB_ISOL_OTG_OFFSET		0x0
> > +#define EXYNOS_5250_USB_ISOL_OTG		(1 << 0)
> > +#define EXYNOS_5250_USB_ISOL_HOST_OFFSET	0x4
> > +#define EXYNOS_5250_USB_ISOL_HOST		(1 << 0)
> > +
> > +enum exynos4x12_phy_id {
> > +	EXYNOS5250_DEVICE,
> > +	EXYNOS5250_HOST,
> > +	EXYNOS5250_HSIC0,
> > +	EXYNOS5250_HSIC1,
> > +	EXYNOS5250_NUM_PHYS,
> > +};
> > +
> > +/* exynos5250_rate_to_clk() converts the supplied clock rate to the
> > +value that
> > + * can be written to the phy register. */
> 
> Follow coding guidelines ;-)
> > +static u32 exynos5250_rate_to_clk(unsigned long rate) {
> > +	unsigned int clksel;
> > +
> > +	/* EXYNOS_5250_FSEL_MASK */
> > +
> > +	switch (rate) {
> > +	case 9600 * KHZ:
> > +		clksel = EXYNOS_5250_FSEL_9MHZ6;
> > +		break;
> > +	case 10 * MHZ:
> > +		clksel = EXYNOS_5250_FSEL_10MHZ;
> > +		break;
> > +	case 12 * MHZ:
> > +		clksel = EXYNOS_5250_FSEL_12MHZ;
> > +		break;
> > +	case 19200 * KHZ:
> > +		clksel = EXYNOS_5250_FSEL_19MHZ2;
> > +		break;
> > +	case 20 * MHZ:
> > +		clksel = EXYNOS_5250_FSEL_20MHZ;
> > +		break;
> > +	case 24 * MHZ:
> > +		clksel = EXYNOS_5250_FSEL_24MHZ;
> > +		break;
> > +	case 50 * MHZ:
> > +		clksel = EXYNOS_5250_FSEL_50MHZ;
> > +		break;
> > +	default:
> > +		clksel = CLKSEL_ERROR;
> > +	}
> > +
> > +	return clksel;
> > +}
> > +
> > +static void exynos5250_isol(struct uphy_instance *inst, bool on) {
> > +	struct uphy_driver *drv = inst->drv;
> > +	u32 offset;
> > +	u32 mask;
> > +	u32 tmp;
> > +
> > +	if (!drv->reg_isol)
> > +		return;
> > +
> > +	switch (inst->cfg->id) {
> > +	case EXYNOS5250_DEVICE:
> > +		offset = EXYNOS_5250_USB_ISOL_OTG_OFFSET;
> > +		mask = EXYNOS_5250_USB_ISOL_OTG;
> > +		break;
> > +	case EXYNOS5250_HOST:
> > +		offset = EXYNOS_5250_USB_ISOL_HOST_OFFSET;
> > +		mask = EXYNOS_5250_USB_ISOL_HOST;
> > +		break;
> > +	default:
> > +		return;
> > +	};
> > +
> > +	tmp = readl(drv->reg_isol + offset);
> > +	if (on)
> > +		tmp &= ~mask;
> > +	else
> > +		tmp |= mask;
> > +	writel(tmp, drv->reg_isol + offset); }
> > +
> > +static void exynos5250_phy_pwr(struct uphy_instance *inst, bool on)
> {
> > +	struct uphy_driver *drv = inst->drv;
> > +	u32 ctrl0;
> > +	u32 otg;
> > +	u32 ehci;
> > +	u32 ohci;
> > +
> > +	switch (inst->cfg->id) {
> > +	case EXYNOS5250_DEVICE:
> > +		writel(0, drv->reg_mode);
> > +
> > +		/* OTG configuration */
> > +		otg = readl(drv->reg_phy + EXYNOS_5250_USBOTGSYS);
> > +		/* The clock */
> > +		otg &= ~EXYNOS_5250_USBOTGSYS_FSEL_MASK;
> > +		otg |= inst->clk << EXYNOS_5250_USBOTGSYS_FSEL_SHIFT;
> > +		/* Reset */
> > +		otg &= ~(EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND |
> > +			EXYNOS_5250_USBOTGSYS_FORCE_SLEEP |
> > +			EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG);
> > +		/* TODO: Clear 4 bits as the old driver does. */
> > +		otg |=	EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
> > +			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET |
> > +			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
> > +			EXYNOS_5250_USBOTGSYS_OTGDISABLE;
> > +		/* Ref clock */
> > +		otg &=	EXYNOS_5250_USBOTGSYS_REFCLKSEL_MASK;
> > +		otg |=  EXYNOS_5250_REFCLKSEL_CLKCORE <<
> > +
EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT;
> > +		writel(otg, drv->reg_phy + EXYNOS_5250_USBOTGSYS);
> > +		udelay(10);
> > +		otg &= ~(EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
> > +			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
> > +			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET);
> > +
> > +
> > +		break;
> > +	case EXYNOS5250_HOST:
> > +		/* Host registers configuration */
> > +		ctrl0 = readl(drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
> > +		/* The clock */
> > +		ctrl0 &= ~EXYNOS_5250_HOSTPHYCTRL0_FSEL_MASK;
> > +		ctrl0 |= inst->clk << EXYNOS_5250_HOSTPHYCTRL0_FSEL_SHIFT;
> > +
> > +		/* Reset */
> > +		ctrl0 &= ~(	EXYNOS_5250_HOSTPHYCTRL0_PHYSWRST |
> > +				EXYNOS_5250_HOSTPHYCTRL0_PHYSWRSTALL |
> > +				EXYNOS_5250_HOSTPHYCTRL0_SIDDQ |
> > +				EXYNOS_5250_HOSTPHYCTRL0_FORCESUSPEND |
> > +				EXYNOS_5250_HOSTPHYCTRL0_FORCESLEEP);
> > +		ctrl0 |=	EXYNOS_5250_HOSTPHYCTRL0_LINKSWRST |
> > +				EXYNOS_5250_HOSTPHYCTRL0_UTMISWRST |
> > +				EXYNOS_5250_HOSTPHYCTRL0_COMMON_ON_N;
> > +		writel(ctrl0, drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
> > +		udelay(10);
> > +		ctrl0 &= ~(	EXYNOS_5250_HOSTPHYCTRL0_LINKSWRST |
> > +				EXYNOS_5250_HOSTPHYCTRL0_UTMISWRST);
> > +		writel(ctrl0, drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
> > +
> > +		/* OTG configuration */
> > +		otg = readl(drv->reg_phy + EXYNOS_5250_USBOTGSYS);
> > +		/* The clock */
> > +		otg &= ~EXYNOS_5250_USBOTGSYS_FSEL_MASK;
> > +		otg |= inst->clk << EXYNOS_5250_USBOTGSYS_FSEL_SHIFT;
> > +		/* Reset */
> > +		otg &= ~(EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND |
> > +			EXYNOS_5250_USBOTGSYS_FORCE_SLEEP |
> > +			EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG);
> > +		/* TODO: Clear 4 bits as the old driver does. */
> > +		otg |=	EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
> > +			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET |
> > +			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
> > +			EXYNOS_5250_USBOTGSYS_OTGDISABLE;
> > +		/* Ref clock */
> > +		otg &=	EXYNOS_5250_USBOTGSYS_REFCLKSEL_MASK;
> > +		otg |=  EXYNOS_5250_REFCLKSEL_CLKCORE <<
> > +
EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT;
> > +		writel(otg, drv->reg_phy + EXYNOS_5250_USBOTGSYS);
> > +		udelay(10);
> > +		otg &= ~(EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
> > +			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
> > +			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET);
> > +
> > +		/* Enable EHCI DMA burst */
> > +		ehci = readl(drv->reg_phy + EXYNOS_5250_HOSTEHCICTRL);
> > +		ehci |=	EXYNOS_5250_HOSTEHCICTRL_ENAINCRXALIGN |
> > +			EXYNOS_5250_HOSTEHCICTRL_ENAINCR4 |
> > +			EXYNOS_5250_HOSTEHCICTRL_ENAINCR8 |
> > +			EXYNOS_5250_HOSTEHCICTRL_ENAINCR16;
> > +		writel(ehci, drv->reg_phy + EXYNOS_5250_HOSTEHCICTRL);
> > +
> > +		/* OHCI settings */
> > +		ohci = readl(drv->reg_phy + EXYNOS_5250_HOSTOHCICTRL);
> > +		/* Let's do some undocumented magic (based on the old
> driver) */
> > +		ohci |=	0x1 << 3;
> > +		writel(ohci, drv->reg_phy + EXYNOS_5250_HOSTOHCICTRL);
> > +
> > +		break;
> > +	}
> > +}
> > +
> > +static int exynos5250_power_on(struct uphy_instance *inst) {
> > +	struct uphy_driver *drv = inst->drv;
> > +
> > +	if (inst->state == STATE_ON) {
> > +		dev_err(drv->dev, "usb phy \"%s\" already on",
> > +							inst->cfg->label);
> > +		return -ENODEV;
> > +	}
> > +
> > +	inst->state = STATE_ON;
> > +	inst->ref_cnt++;
> > +	if (inst->ref_cnt > 1)
> > +		return 0;
> > +
> > +	exynos5250_phy_pwr(inst, 1);
> > +	exynos5250_isol(inst, 0);
> > +
> > +	/* Power on the device, as it is necessary for HSIC to work */
> > +	if (inst->cfg->id == EXYNOS5250_HSIC0) {
> > +		struct uphy_instance *device =
> > +
&drv->uphy_instances[EXYNOS5250_DEVICE];
> > +		device->ref_cnt++;
> > +		if (device->ref_cnt > 1)
> > +			return 0;
> > +		exynos5250_phy_pwr(device, 1);
> > +		exynos5250_isol(device, 0);
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int exynos5250_power_off(struct uphy_instance *inst) {
> > +	struct uphy_driver *drv = inst->drv;
> > +
> > +	if (inst->state == STATE_OFF) {
> > +		dev_err(drv->dev, "usb phy \"%s\" already off",
> > +							inst->cfg->label);
> > +		return -EINVAL;
> > +	}
> > +
> > +	inst->state = STATE_OFF;
> > +	inst->ref_cnt--;
> > +
> > +	if (inst->ref_cnt > 0)
> > +		return 0;
> > +
> > +	exynos5250_isol(inst, 1);
> > +	exynos5250_phy_pwr(inst, 0);
> > +
> > +	if (inst->cfg->id == EXYNOS5250_HSIC0) {
> > +		struct uphy_instance *device =
> > +
&drv->uphy_instances[EXYNOS5250_DEVICE];
> > +		device->ref_cnt--;
> > +		if (device->ref_cnt > 0)
> > +			return 0;
> > +		exynos5250_isol(device, 1);
> > +		exynos5250_phy_pwr(device, 0);
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +
> > +static const struct common_phy exynos5250_phys[] = {
> > +	{
> > +		.label		= "device",
> > +		.type		= PHY_DEVICE,
> > +		.id		= EXYNOS5250_DEVICE,
> > +		.rate_to_clk	= exynos5250_rate_to_clk,
> > +		.power_on	= exynos5250_power_on,
> > +		.power_off	= exynos5250_power_off,
> > +	},
> > +	{
> > +		.label		= "host",
> > +		.type		= PHY_HOST,
> > +		.id		= EXYNOS5250_HOST,
> > +		.rate_to_clk	= exynos5250_rate_to_clk,
> > +		.power_on	= exynos5250_power_on,
> > +		.power_off	= exynos5250_power_off,
> > +	},
> > +	{
> > +		.label		= "hsic0",
> > +		.type		= PHY_HOST,
> > +		.id		= EXYNOS5250_HSIC0,
> > +		.rate_to_clk	= exynos5250_rate_to_clk,
> > +		.power_on	= exynos5250_power_on,
> > +		.power_off	= exynos5250_power_off,
> > +	},
> > +	{
> > +		.label		= "hsic1",
> > +		.type		= PHY_HOST,
> > +		.id		= EXYNOS5250_HSIC1,
> > +		.rate_to_clk	= exynos5250_rate_to_clk,
> > +		.power_on	= exynos5250_power_on,
> > +		.power_off	= exynos5250_power_off,
> > +	},
> > +	{},
> > +};
> 
> All this can be removed if you don't use exynos common PHY.

Ok. Now, I think, I start to understand you better. Still there is the
question - one single driver or many small drivers with repeated code.

> 
> Thanks
> Kishon

Best wishes,
-- 
Kamil Debski
Samsung R&D Institute Poland



--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux