Add hwmod data for High Speed USB host and TLL modules
CC: Paul Walmsley <paul@xxxxxxxxx>
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
arch/arm/mach-omap2/omap_hwmod_54xx_data.c | 135 ++++++++++++++++++++++++++++
1 files changed, 135 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
index 1a21a81..1dd2c20 100644
--- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
@@ -1501,6 +1501,123 @@ static struct omap_hwmod omap54xx_uart6_hwmod = {
};
/*
+ * 'usb_host_hs' class
+ * high-speed multi-port usb host controller
+ */
+
+static struct omap_hwmod_class_sysconfig omap54xx_usb_host_hs_sysc = {
+ .rev_offs = 0x0000,
+ .sysc_offs = 0x0010,
+ .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_RESET_STATUS |
+ SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET),
+ .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+ SIDLE_SMART_WKUP | MSTANDBY_FORCE | MSTANDBY_NO |
+ MSTANDBY_SMART | MSTANDBY_SMART_WKUP),
+ .sysc_fields = &omap_hwmod_sysc_type2,
+};
+
+static struct omap_hwmod_class omap54xx_usb_host_hs_hwmod_class = {
+ .name = "usb_host_hs",
+ .sysc = &omap54xx_usb_host_hs_sysc,
+};
+
+static struct omap_hwmod omap54xx_usb_host_hs_hwmod = {
+ .name = "usb_host_hs",
+ .class = &omap54xx_usb_host_hs_hwmod_class,
+ .clkdm_name = "l3init_clkdm",
+ /*
+ * Errata: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
+ * id: i660
+ *
+ * Description:
+ * In the following configuration :
+ * - USBHOST module is set to smart-idle mode
+ * - PRCM asserts idle_req to the USBHOST module ( This typically
+ * happens when the system is going to a low power mode : all ports
+ * have been suspended, the master part of the USBHOST module has
+ * entered the standby state, and SW has cut the functional clocks)
+ * - an USBHOST interrupt occurs before the module is able to answer
+ * idle_ack, typically a remote wakeup IRQ.
+ * Then the USB HOST module will enter a deadlock situation where it
+ * is no more accessible nor functional.
+ *
+ * Workaround:
+ * Don't use smart idle; use only force idle, hence HWMOD_SWSUP_SIDLE
+ */
+
+ /*
+ * Errata: USB host EHCI may stall when entering smart-standby mode
+ * Id: i571
+ *
+ * Description:
+ * When the USBHOST module is set to smart-standby mode, and when it is
+ * ready to enter the standby state (i.e. all ports are suspended and
+ * all attached devices are in suspend mode), then it can wrongly assert
+ * the Mstandby signal too early while there are still some residual OCP
+ * transactions ongoing. If this condition occurs, the internal state
+ * machine may go to an undefined state and the USB link may be stuck
+ * upon the next resume.
+ *
+ * Workaround:
+ * Don't use smart standby; use only force standby,
+ * hence HWMOD_SWSUP_MSTANDBY
+ */
+
+ /*
+ * During system boot; If the hwmod framework resets the module
+ * the module will have smart idle settings; which can lead to deadlock
+ * (above Errata Id:i660); so, dont reset the module during boot;
+ * Use HWMOD_INIT_NO_RESET.
+ */
+
+ .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY |
+ HWMOD_INIT_NO_RESET,
+ .main_clk = "l3init_60m_fclk",
+ .prcm = {
+ .omap4 = {
+ .clkctrl_offs = OMAP54XX_CM_L3INIT_USB_HOST_HS_CLKCTRL_OFFSET,
+ .context_offs = OMAP54XX_RM_L3INIT_USB_HOST_HS_CONTEXT_OFFSET,
+ .modulemode = MODULEMODE_SWCTRL,
+ },
+ },
+};
+
+/*
+ * 'usb_tll_hs' class
+ * usb_tll_hs module is the adapter on the usb_host_hs ports
+ */
+
+static struct omap_hwmod_class_sysconfig omap54xx_usb_tll_hs_sysc = {
+ .rev_offs = 0x0000,
+ .sysc_offs = 0x0010,
+ .syss_offs = 0x0014,
+ .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY |
+ SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE |
+ SYSC_HAS_SOFTRESET | SYSS_HAS_RESET_STATUS),
+ .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+ .sysc_fields = &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap54xx_usb_tll_hs_hwmod_class = {
+ .name = "usb_tll_hs",
+ .sysc = &omap54xx_usb_tll_hs_sysc,
+};
+
+static struct omap_hwmod omap54xx_usb_tll_hs_hwmod = {
+ .name = "usb_tll_hs",
+ .class = &omap54xx_usb_tll_hs_hwmod_class,
+ .clkdm_name = "l3init_clkdm",
+ .main_clk = "l4_root_clk_div",
+ .prcm = {
+ .omap4 = {
+ .clkctrl_offs = OMAP54XX_CM_L3INIT_USB_TLL_HS_CLKCTRL_OFFSET,
+ .context_offs = OMAP54XX_RM_L3INIT_USB_TLL_HS_CONTEXT_OFFSET,
+ .modulemode = MODULEMODE_HWCTRL,
+ },
+ },
+};
+
+/*
* 'usb_otg_ss' class
* 2.0 super speed (usb_otg_ss) controller
*/
@@ -2140,6 +2257,22 @@ static struct omap_hwmod_ocp_if omap54xx_l4_per__uart6 = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
+/* l4_cfg -> usb_host_hs */
+static struct omap_hwmod_ocp_if omap54xx_l4_cfg__usb_host_hs = {
+ .master = &omap54xx_l4_cfg_hwmod,
+ .slave = &omap54xx_usb_host_hs_hwmod,
+ .clk = "l3_iclk_div",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* l4_cfg -> usb_tll_hs */
+static struct omap_hwmod_ocp_if omap54xx_l4_cfg__usb_tll_hs = {
+ .master = &omap54xx_l4_cfg_hwmod,
+ .slave = &omap54xx_usb_tll_hs_hwmod,
+ .clk = "l4_root_clk_div",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
/* l4_cfg -> usb_otg_ss */
static struct omap_hwmod_ocp_if omap54xx_l4_cfg__usb_otg_ss = {
.master = &omap54xx_l4_cfg_hwmod,
@@ -2225,6 +2358,8 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = {
&omap54xx_l4_per__uart4,
&omap54xx_l4_per__uart5,
&omap54xx_l4_per__uart6,
+ &omap54xx_l4_cfg__usb_host_hs,
+ &omap54xx_l4_cfg__usb_tll_hs,
&omap54xx_l4_cfg__usb_otg_ss,
&omap54xx_l4_wkup__wd_timer2,
NULL,
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
