The support for both am335x-USB instances required changes to the device
tree bindings. This patch reflects these changes in the bindings
document.
v3…v4:
- remove the child node for USB. This is driver specific on won't be
reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
is used by a few other drivers.
v2…v3:
- use proper usb-phy nodes in evm, bone and evmsk device tree.
v1…v2:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- use usbX-phy instead of usbX_phy
- use dma-controller instead of dma
Cc: Rob Herring <rob.herring@xxxxxxxxxxx>
Cc: Pawel Moll <pawel.moll@xxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Stephen Warren <swarren@xxxxxxxxxxxxx>
Cc: Ian Campbell <ian.campbell@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@xxxxxxxxxxxxx>
---
.../devicetree/bindings/usb/am33xx-usb.txt | 222 ++++++++++++++++++---
1 file changed, 192 insertions(+), 30 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
index dc9dc8c..20c2ff2 100644
--- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -1,35 +1,197 @@
-AM33XX MUSB GLUE
- - compatible : Should be "ti,musb-am33xx"
- - reg : offset and length of register sets, first usbss, then for musb instances
- - interrupts : usbss, musb instance interrupts in order
- - ti,hwmods : must be "usb_otg_hs"
- - multipoint : Should be "1" indicating the musb controller supports
- multipoint. This is a MUSB configuration-specific setting.
- - num-eps : Specifies the number of endpoints. This is also a
- MUSB configuration-specific setting. Should be set to "16"
- - ram-bits : Specifies the ram address size. Should be set to "12"
- - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
- represents PERIPHERAL.
- - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
- represents PERIPHERAL.
- - power : Should be "250". This signifies the controller can supply up to
- 500mA when operating in host mode.
+ AM33xx MUSB
+~~~~~~~~~~~~~~~
+- compatible: ti,am33xx-usb
+- reg: offset and length of the usbss register sets
+- ti,hwmods : must be "usb_otg_hs"
+
+The glue layer contains multiple child nodes. It is required the have
+at least a control module node, USB node and a PHY node. The second USB
+node and its PHY node is optional. The DMA node is also optional.
+
+Reset module
+~~~~~~~~~~~~
+- compatible: ti,am335x-usb-ctrl-module
+- reg: offset and length of the "USB control registers" in the "Control
+ Module" block. A second offset and length for the USB wake up control
+ in the same memory block.
+- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for
+ the USB wake up control register.
+
+USB PHY
+~~~~~~~
+compatible: ti,am335x-usb-phy
+reg: offset and length of the "USB PHY" register space
+ti,ctrl_mod: reference to the "reset module" node
+reg-names: phy
+The PHY should have a "phy" alias numbered properly in the alias
+node.
+
+USB
+~~~
+- compatible: ti,musb-am33xx
+- reg: offset and length of "USB Controller Registers", and offset and
+ length of "USB Core" register space.
+- reg-names: control for the ""USB Controller Registers" and "mc" for
+ "USB Core" register space
+- interrupts: USB interrupt number
+- interrupt-names: mc
+- dr_mode: Should be one of "host", "peripheral" or "otg".
+- mentor,multipoint: Should be "1" indicating the musb controller supports
+ multipoint. This is a MUSB configuration-specific setting.
+- mentor,num-eps: Specifies the number of endpoints. This is also a
+ MUSB configuration-specific setting. Should be set to "16"
+- mentor,ram-bits: Specifies the ram address size. Should be set to "12"
+- mentor,power: Should be "500". This signifies the controller can supply up to
+ 500mA when operating in host mode.
+- phys: reference to the USB phy
+- dmas: specifies the dma channels
+- dma-names: specifies the names of the channels. Use "rxN" for receive
+ and "txN" for transmit endpoints. N specifies the endpoint number.
+
+The controller should have an "usb" alias numbered properly in the alias
+node.
+
+DMA
+~~~
+- compatible: ti,am3359-cppi41
+- reg: offset and length of the following register spaces: USBSS, USB
+ CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager
+- reg-names: glue, controller, scheduler, queuemgr
+- #dma-cells: should be set to 2. The first number represents the
+ endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29
+ for endpoints 1 … 15 on instance 1). The second number is 0 for RX and
+ 1 for TX transfers.
+- #dma-channels: should be set to 30 representing the 15 endpoints for
+ each USB instance.
Example:
+~~~~~~~~
+The following example contains all the nodes as used on am335x-evm:
+
+aliases {
+ usb0 = &usb0;
+ usb1 = &usb1;
+ phy0 = &usb0_phy;
+ phy1 = &usb1_phy;
+};
-usb@47400000 {
- compatible = "ti,musb-am33xx";
- reg = <0x47400000 0x1000 /* usbss */
- 0x47401000 0x800 /* musb instance 0 */
- 0x47401800 0x800>; /* musb instance 1 */
- interrupts = <17 /* usbss */
- 18 /* musb instance 0 */
- 19>; /* musb instance 1 */
- multipoint = <1>;
- num-eps = <16>;
- ram-bits = <12>;
- port0-mode = <3>;
- port1-mode = <3>;
- power = <250>;
+usb: usb@47400000 {
+ compatible = "ti,am33xx-usb";
+ reg = <0x47400000 0x1000>;
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
ti,hwmods = "usb_otg_hs";
+
+ ctrl_mod: control@44e10000 {
+ compatible = "ti,am335x-usb-ctrl-module";
+ reg = <0x44e10620 0x10
+ 0x44e10648 0x4>;
+ reg-names = "phy_ctrl", "wakeup";
+ };
+
+ usb0_phy: usb-phy@47401300 {
+ compatible = "ti,am335x-usb-phy";
+ reg = <0x47401300 0x100>;
+ reg-names = "phy";
+ ti,ctrl_mod = <&ctrl_mod>;
+ };
+
+ usb0: usb@47401000 {
+ compatible = "ti,musb-am33xx";
+ reg = <0x47401400 0x400
+ 0x47401000 0x200>;
+ reg-names = "mc", "control";
+
+ interrupts = <18>;
+ interrupt-names = "mc";
+ dr_mode = "otg"
+ mentor,multipoint = <1>;
+ mentor,num-eps = <16>;
+ mentor,ram-bits = <12>;
+ mentor,power = <500>;
+ phys = <&usb0_phy>;
+
+ dmas = <&cppi41dma 0 0 &cppi41dma 1 0
+ &cppi41dma 2 0 &cppi41dma 3 0
+ &cppi41dma 4 0 &cppi41dma 5 0
+ &cppi41dma 6 0 &cppi41dma 7 0
+ &cppi41dma 8 0 &cppi41dma 9 0
+ &cppi41dma 10 0 &cppi41dma 11 0
+ &cppi41dma 12 0 &cppi41dma 13 0
+ &cppi41dma 14 0 &cppi41dma 0 1
+ &cppi41dma 1 1 &cppi41dma 2 1
+ &cppi41dma 3 1 &cppi41dma 4 1
+ &cppi41dma 5 1 &cppi41dma 6 1
+ &cppi41dma 7 1 &cppi41dma 8 1
+ &cppi41dma 9 1 &cppi41dma 10 1
+ &cppi41dma 11 1 &cppi41dma 12 1
+ &cppi41dma 13 1 &cppi41dma 14 1>;
+ dma-names =
+ "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+ "rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+ "rx14", "rx15",
+ "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+ "tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+ "tx14", "tx15";
+ };
+
+ usb1_phy: usb-phy@47401b00 {
+ compatible = "ti,am335x-usb-phy";
+ reg = <0x47401b00 0x100>;
+ reg-names = "phy";
+ ti,ctrl_mod = <&ctrl_mod>;
+ };
+
+ usb1: usb@47401800 {
+ compatible = "ti,musb-am33xx";
+ reg = <0x47401c00 0x400
+ 0x47401800 0x200>;
+ reg-names = "mc", "control";
+ interrupts = <19>;
+ interrupt-names = "mc";
+ dr_mode = "host"
+ mentor,multipoint = <1>;
+ mentor,num-eps = <16>;
+ mentor,ram-bits = <12>;
+ mentor,power = <500>;
+ phys = <&usb1_phy>;
+
+ dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+ &cppi41dma 17 0 &cppi41dma 18 0
+ &cppi41dma 19 0 &cppi41dma 20 0
+ &cppi41dma 21 0 &cppi41dma 22 0
+ &cppi41dma 23 0 &cppi41dma 24 0
+ &cppi41dma 25 0 &cppi41dma 26 0
+ &cppi41dma 27 0 &cppi41dma 28 0
+ &cppi41dma 29 0 &cppi41dma 15 1
+ &cppi41dma 16 1 &cppi41dma 17 1
+ &cppi41dma 18 1 &cppi41dma 19 1
+ &cppi41dma 20 1 &cppi41dma 21 1
+ &cppi41dma 22 1 &cppi41dma 23 1
+ &cppi41dma 24 1 &cppi41dma 25 1
+ &cppi41dma 26 1 &cppi41dma 27 1
+ &cppi41dma 28 1 &cppi41dma 29 1>;
+ dma-names =
+ "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+ "rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+ "rx14", "rx15",
+ "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+ "tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+ "tx14", "tx15";
+ };
+
+ cppi41dma: dma-controller@07402000 {
+ compatible = "ti,am3359-cppi41";
+ reg = <0x47400000 0x1000
+ 0x47402000 0x1000
+ 0x47403000 0x1000
+ 0x47404000 0x4000>;
+ reg-names = "glue", "controller", "scheduler", "queuemgr";
+ interrupts = <17>;
+ interrupt-names = "glue";
+ #dma-cells = <2>;
+ #dma-channels = <30>;
+ #dma-requests = <256>;
+ };
};
--
1.8.4.rc2
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
