On Wed, 2013-07-31 at 18:51 +0800, Ming Lei wrote:
> This patch enables 'can_dma_sg' flag for ax88179_178a device
> if the attached host controller supports building packet from
> discontinuous buffers(DMA SG is possible), so both frame header
> and skb data buffers can be passed to usb stack via urb->sg,
> then skb data copy can be saved.
>
> With the patch, CPU utilization decreased much in iperf test at
> client mode.
>
> Signed-off-by: Ming Lei <ming.lei@xxxxxxxxxxxxx>
> ---
> drivers/net/usb/ax88179_178a.c | 30 ++++++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/drivers/net/usb/ax88179_178a.c b/drivers/net/usb/ax88179_178a.c
> index 5a468f3..c75bded 100644
> --- a/drivers/net/usb/ax88179_178a.c
> +++ b/drivers/net/usb/ax88179_178a.c
> @@ -1031,12 +1031,20 @@ static int ax88179_bind(struct usbnet *dev, struct usb_interface *intf)
> dev->mii.phy_id = 0x03;
> dev->mii.supports_gmii = 1;
>
> + if (dev->udev->bus->no_sg_limit)
> + dev->can_dma_sg = 1;
> +
> dev->net->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
> NETIF_F_RXCSUM;
>
> dev->net->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
> NETIF_F_RXCSUM;
>
> + if (dev->can_dma_sg) {
> + dev->net->features |= NETIF_F_SG | NETIF_F_TSO;
> + dev->net->hw_features |= NETIF_F_SG | NETIF_F_TSO;
> + }
> +
> /* Enable checksum offload */
> *tmp = AX_RXCOE_IP | AX_RXCOE_TCP | AX_RXCOE_UDP |
> AX_RXCOE_TCPV6 | AX_RXCOE_UDPV6;
> @@ -1170,12 +1178,30 @@ ax88179_tx_fixup(struct usbnet *dev, struct sk_buff *skb, gfp_t flags)
> int mss = skb_shinfo(skb)->gso_size;
> int headroom;
> int tailroom;
> + struct skb_data *entry = (struct skb_data *)skb->cb;
>
> tx_hdr1 = skb->len;
> tx_hdr2 = mss;
> if (((skb->len + 8) % frame_size) == 0)
> tx_hdr2 |= 0x80008000; /* Enable padding */
>
> + if (dev->can_dma_sg) {
> + if (!(entry->header = kmalloc(8, GFP_ATOMIC)))
> + goto no_sg;
> +
> + entry->length = 8;
> + cpu_to_le32s(&tx_hdr1);
> + cpu_to_le32s(&tx_hdr2);
You could do these cpu_to_le32s() calls before the if (dev->can_dma_sg)
and remove them before the skb_copy_to_linear_data() calls.
> + memcpy(entry->header, &tx_hdr1, 4);
> + memcpy(entry->header + 4, &tx_hdr2, 4);
> +
> + return skb;
> + } else {
> +no_sg:
> + entry->header = NULL;
> + entry->length = 0;
> + }
> +
> headroom = skb_headroom(skb);
> tailroom = skb_tailroom(skb);
>
> @@ -1323,6 +1349,10 @@ static int ax88179_reset(struct usbnet *dev)
>
> dev->net->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
> NETIF_F_RXCSUM;
> + if (dev->can_dma_sg) {
> + dev->net->features |= NETIF_F_SG | NETIF_F_TSO;
> + dev->net->hw_features |= NETIF_F_SG | NETIF_F_TSO;
> + }
Are you sure this part is needed ?
Also it looks like that you are going through this sg allocation/setup
even for linear skb ?
For linear skb, with 8+ bytes of headroom, I guess this adds significant
overhead (2 kmalloc() + sg setup)
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
