Hello, one of my external HDDs does not work using 3.11-rc2. The drive works using 3.10, and 3.9, except for a suspend/resume issue described here: https://bugzilla.redhat.com/show_bug.cgi?id=984189 . dmesg snipped: [ 119.334908] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd [ 119.347397] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [ 119.350614] usb 4-1: New USB device found, idVendor=054c, idProduct=c005 [ 119.350620] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 119.350624] usb 4-1: Product: USB 3.0 SATA Bridge [ 119.350627] usb 4-1: Manufacturer: VIA Technologies Inc. [ 119.350630] usb 4-1: SerialNumber: lþmµóA¹ñô\xffffffc2\xffffff80ô¥7õ\d [ 119.377782] usb-storage 4-1:1.0: USB Mass Storage device detected [ 119.377847] scsi6 : usb-storage 4-1:1.0 [ 119.377900] usbcore: registered new interface driver usb-storage [ 129.844989] scsi 6:0:0:0: Direct-Access Hitachi HDS5C3030BLE MZ6O PQ: 0 ANSI: 6 [ 129.845465] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 129.863425] sd 6:0:0:0: [sdb] 732566646 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 129.871203] sd 6:0:0:0: [sdb] Write Protect is off [ 129.871209] sd 6:0:0:0: [sdb] Mode Sense: 2f 00 00 00 [ 129.879196] sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 160.787920] usb 4-1: reset SuperSpeed USB device number 2 using xhci_hcd [ 160.800582] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [ 160.801795] usb 4-1: device firmware changed [ 160.801857] usb 4-1: USB disconnect, device number 2 [ 160.801938] sd 6:0:0:0: Device offlined - not ready after error recovery [ 160.805190] sd 6:0:0:0: [sdb] READ CAPACITY failed [ 160.805194] sd 6:0:0:0: [sdb] [ 160.805195] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 160.805197] sd 6:0:0:0: [sdb] Sense not available. [ 160.805218] sd 6:0:0:0: [sdb] Asking for cache data failed [ 160.805220] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 160.805233] sdb: detected capacity change from 3000592982016 to 0 [ 160.805353] sd 6:0:0:0: [sdb] READ CAPACITY failed [ 160.805357] sd 6:0:0:0: [sdb] [ 160.805359] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 160.805361] sd 6:0:0:0: [sdb] Sense not available. [ 160.805383] sd 6:0:0:0: [sdb] No Caching mode page present [ 160.805386] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 160.805397] sd 6:0:0:0: [sdb] Attached SCSI disk [ 160.806605] xhci_hcd 0000:0e:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880212315e80 [ 160.806609] xhci_hcd 0000:0e:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880212315ec0 kernel log, lsusb and usbmon are attached. I tried usb2 and 3 ports, both have the same issue with this drive. Other drives work. Thanks, Philipp
Attachment:
logs.tar.bz2
Description: BZip2 compressed data
