From: Stephen Warren <swarren@xxxxxxxxxx>
The PM routines in ehci-tegra.c use APIs such as ehci_reset(),
ehci_halt(), and ehci_tdi_reset() that would need to be exported to
convert ehci-tegra.c into a separate module from ehci-hcd.c. However,
we'd prefer not to export them.
Instead, simply remove all power management functionality. Runtime PM
was disabled since it didn't work correctly, and system suspend isn't
yet supported in a meaningful way. So, this change doesn't lose any
functionality.
Hopefully the power management logic can be reimplemented in a cleaner
way in the future.
Signed-off-by: Stephen Warren <swarren@xxxxxxxxxx>
Acked-by: Arnd Bergmann <arnd@xxxxxxxx>
Acked-by: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx>
---
v3:
* Also remove tegra_ehci_power_up(), tegra_ehci_shutdown(), struct
tegra_ehci_hcd.host_resumed.
* Add back .bus_{suspend,resume} entries in tegra_ehci_hc_driver.
v2: New patch.
---
drivers/usb/host/ehci-tegra.c | 246 +-----------------------------------------
1 file changed, 1 insertion(+), 245 deletions(-)
diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c
index 289b9b8..dde5189 100644
--- a/drivers/usb/host/ehci-tegra.c
+++ b/drivers/usb/host/ehci-tegra.c
@@ -46,30 +46,11 @@ struct tegra_ehci_hcd {
struct tegra_usb_phy *phy;
struct clk *clk;
struct usb_phy *transceiver;
- int host_resumed;
int port_resuming;
bool needs_double_reset;
enum tegra_usb_phy_port_speed port_speed;
};
-static void tegra_ehci_power_up(struct usb_hcd *hcd)
-{
- struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller);
-
- clk_prepare_enable(tegra->clk);
- usb_phy_set_suspend(hcd->phy, 0);
- tegra->host_resumed = 1;
-}
-
-static void tegra_ehci_power_down(struct usb_hcd *hcd)
-{
- struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller);
-
- tegra->host_resumed = 0;
- usb_phy_set_suspend(hcd->phy, 1);
- clk_disable_unprepare(tegra->clk);
-}
-
static int tegra_ehci_internal_port_reset(
struct ehci_hcd *ehci,
u32 __iomem *portsc_reg
@@ -248,39 +229,6 @@ done:
return retval;
}
-static void tegra_ehci_restart(struct usb_hcd *hcd)
-{
- struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-
- ehci_reset(ehci);
-
- /* setup the frame list and Async q heads */
- ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
- ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next);
- /* setup the command register and set the controller in RUN mode */
- ehci->command &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET);
- ehci->command |= CMD_RUN;
- ehci_writel(ehci, ehci->command, &ehci->regs->command);
-
- down_write(&ehci_cf_port_reset_rwsem);
- ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
- /* flush posted writes */
- ehci_readl(ehci, &ehci->regs->command);
- up_write(&ehci_cf_port_reset_rwsem);
-}
-
-static void tegra_ehci_shutdown(struct usb_hcd *hcd)
-{
- struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller);
-
- /* ehci_shutdown touches the USB controller registers, make sure
- * controller has clocks to it */
- if (!tegra->host_resumed)
- tegra_ehci_power_up(hcd);
-
- ehci_shutdown(hcd);
-}
-
static int tegra_ehci_setup(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
@@ -395,7 +343,7 @@ static const struct hc_driver tegra_ehci_hc_driver = {
/* modified ehci functions for tegra */
.reset = tegra_ehci_setup,
- .shutdown = tegra_ehci_shutdown,
+ .shutdown = ehci_shutdown,
.map_urb_for_dma = tegra_ehci_map_urb_for_dma,
.unmap_urb_for_dma = tegra_ehci_unmap_urb_for_dma,
.hub_control = tegra_ehci_hub_control,
@@ -432,182 +380,6 @@ static int setup_vbus_gpio(struct platform_device *pdev,
return err;
}
-#ifdef CONFIG_PM
-
-static int controller_suspend(struct device *dev)
-{
- struct tegra_ehci_hcd *tegra =
- platform_get_drvdata(to_platform_device(dev));
- struct ehci_hcd *ehci = tegra->ehci;
- struct usb_hcd *hcd = ehci_to_hcd(ehci);
- struct ehci_regs __iomem *hw = ehci->regs;
- unsigned long flags;
-
- if (time_before(jiffies, ehci->next_statechange))
- msleep(10);
-
- ehci_halt(ehci);
-
- spin_lock_irqsave(&ehci->lock, flags);
- tegra->port_speed = (readl(&hw->port_status[0]) >> 26) & 0x3;
- clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
- spin_unlock_irqrestore(&ehci->lock, flags);
-
- tegra_ehci_power_down(hcd);
- return 0;
-}
-
-static int controller_resume(struct device *dev)
-{
- struct tegra_ehci_hcd *tegra =
- platform_get_drvdata(to_platform_device(dev));
- struct ehci_hcd *ehci = tegra->ehci;
- struct usb_hcd *hcd = ehci_to_hcd(ehci);
- struct ehci_regs __iomem *hw = ehci->regs;
- unsigned long val;
-
- set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
- tegra_ehci_power_up(hcd);
-
- if (tegra->port_speed > TEGRA_USB_PHY_PORT_SPEED_HIGH) {
- /* Wait for the phy to detect new devices
- * before we restart the controller */
- msleep(10);
- goto restart;
- }
-
- /* Force the phy to keep data lines in suspend state */
- tegra_ehci_phy_restore_start(hcd->phy, tegra->port_speed);
-
- /* Enable host mode */
- tdi_reset(ehci);
-
- /* Enable Port Power */
- val = readl(&hw->port_status[0]);
- val |= PORT_POWER;
- writel(val, &hw->port_status[0]);
- udelay(10);
-
- /* Check if the phy resume from LP0. When the phy resume from LP0
- * USB register will be reset. */
- if (!readl(&hw->async_next)) {
- /* Program the field PTC based on the saved speed mode */
- val = readl(&hw->port_status[0]);
- val &= ~PORT_TEST(~0);
- if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_HIGH)
- val |= PORT_TEST_FORCE;
- else if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_FULL)
- val |= PORT_TEST(6);
- else if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW)
- val |= PORT_TEST(7);
- writel(val, &hw->port_status[0]);
- udelay(10);
-
- /* Disable test mode by setting PTC field to NORMAL_OP */
- val = readl(&hw->port_status[0]);
- val &= ~PORT_TEST(~0);
- writel(val, &hw->port_status[0]);
- udelay(10);
- }
-
- /* Poll until CCS is enabled */
- if (ehci_handshake(ehci, &hw->port_status[0], PORT_CONNECT,
- PORT_CONNECT, 2000)) {
- pr_err("%s: timeout waiting for PORT_CONNECT\n", __func__);
- goto restart;
- }
-
- /* Poll until PE is enabled */
- if (ehci_handshake(ehci, &hw->port_status[0], PORT_PE,
- PORT_PE, 2000)) {
- pr_err("%s: timeout waiting for USB_PORTSC1_PE\n", __func__);
- goto restart;
- }
-
- /* Clear the PCI status, to avoid an interrupt taken upon resume */
- val = readl(&hw->status);
- val |= STS_PCD;
- writel(val, &hw->status);
-
- /* Put controller in suspend mode by writing 1 to SUSP bit of PORTSC */
- val = readl(&hw->port_status[0]);
- if ((val & PORT_POWER) && (val & PORT_PE)) {
- val |= PORT_SUSPEND;
- writel(val, &hw->port_status[0]);
-
- /* Wait until port suspend completes */
- if (ehci_handshake(ehci, &hw->port_status[0], PORT_SUSPEND,
- PORT_SUSPEND, 1000)) {
- pr_err("%s: timeout waiting for PORT_SUSPEND\n",
- __func__);
- goto restart;
- }
- }
-
- tegra_ehci_phy_restore_end(hcd->phy);
- goto done;
-
- restart:
- if (tegra->port_speed <= TEGRA_USB_PHY_PORT_SPEED_HIGH)
- tegra_ehci_phy_restore_end(hcd->phy);
-
- tegra_ehci_restart(hcd);
-
- done:
- tegra_usb_phy_preresume(hcd->phy);
- tegra->port_resuming = 1;
- return 0;
-}
-
-static int tegra_ehci_suspend(struct device *dev)
-{
- struct tegra_ehci_hcd *tegra =
- platform_get_drvdata(to_platform_device(dev));
- struct usb_hcd *hcd = ehci_to_hcd(tegra->ehci);
- int rc = 0;
-
- /*
- * When system sleep is supported and USB controller wakeup is
- * implemented: If the controller is runtime-suspended and the
- * wakeup setting needs to be changed, call pm_runtime_resume().
- */
- if (HCD_HW_ACCESSIBLE(hcd))
- rc = controller_suspend(dev);
- return rc;
-}
-
-static int tegra_ehci_resume(struct device *dev)
-{
- int rc;
-
- rc = controller_resume(dev);
- if (rc == 0) {
- pm_runtime_disable(dev);
- pm_runtime_set_active(dev);
- pm_runtime_enable(dev);
- }
- return rc;
-}
-
-static int tegra_ehci_runtime_suspend(struct device *dev)
-{
- return controller_suspend(dev);
-}
-
-static int tegra_ehci_runtime_resume(struct device *dev)
-{
- return controller_resume(dev);
-}
-
-static const struct dev_pm_ops tegra_ehci_pm_ops = {
- .suspend = tegra_ehci_suspend,
- .resume = tegra_ehci_resume,
- .runtime_suspend = tegra_ehci_runtime_suspend,
- .runtime_resume = tegra_ehci_runtime_resume,
-};
-
-#endif
-
/* Bits of PORTSC1, which will get cleared by writing 1 into them */
#define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC)
@@ -746,7 +518,6 @@ static int tegra_ehci_probe(struct platform_device *pdev)
goto cleanup_phy;
}
- tegra->host_resumed = 1;
tegra->ehci = hcd_to_ehci(hcd);
irq = platform_get_irq(pdev, 0);
@@ -773,14 +544,6 @@ static int tegra_ehci_probe(struct platform_device *pdev)
goto cleanup_phy;
}
- pm_runtime_set_active(&pdev->dev);
- pm_runtime_get_noresume(&pdev->dev);
-
- /* Don't skip the pm_runtime_forbid call if wakeup isn't working */
- /* if (!pdata->power_down_on_bus_suspend) */
- pm_runtime_forbid(&pdev->dev);
- pm_runtime_enable(&pdev->dev);
- pm_runtime_put_sync(&pdev->dev);
return err;
cleanup_phy:
@@ -800,10 +563,6 @@ static int tegra_ehci_remove(struct platform_device *pdev)
struct tegra_ehci_hcd *tegra = platform_get_drvdata(pdev);
struct usb_hcd *hcd = ehci_to_hcd(tegra->ehci);
- pm_runtime_get_sync(&pdev->dev);
- pm_runtime_disable(&pdev->dev);
- pm_runtime_put_noidle(&pdev->dev);
-
if (!IS_ERR(tegra->transceiver))
otg_set_host(tegra->transceiver->otg, NULL);
@@ -837,8 +596,5 @@ static struct platform_driver tegra_ehci_driver = {
.driver = {
.name = "tegra-ehci",
.of_match_table = tegra_ehci_of_match,
-#ifdef CONFIG_PM
- .pm = &tegra_ehci_pm_ops,
-#endif
}
};
--
1.8.1.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
