Hi guys, I recently noticed a problem with suspend-to-disk on my Thinkpad X201. I'm using swsusp, which offers a "press backspace to cancel" while it is writing out the suspend image to the swap partition. When I do this, the system mostly recovers, except for the USB ports on my docking station, which stop working (until I undock and redock again). The USB ports on the laptop itself seem unaffected. During a normal suspend-resume (both to disk and to ram), the ports are also enabled properly. I bisected this problem and it was introduced by the following commit: commit c73cee717e7d5da0698acb720ad1219646fe4f46 Author: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx> Date: Wed Oct 31 13:21:06 2012 -0400 USB: EHCI: remove ehci_port_power() routine This patch (as1623) removes the ehci_port_power() routine and all the places that call it. There's no reason for ehci-hcd to change the port power settings; the hub driver takes care of all that stuff. There is one exception: When the controller is resumed from hibernation or following a loss of power, the ports that are supposed to be handed over to a companion controller must be powered on first. Otherwise the handover won't work. This process is not visible to the hub driver, so it has to be handled in ehci-hcd. Perhaps there is some code path or set of ports that also need this exception? I tried reverting this patch on 3.9-rc4 and usb-next, but I got conflicts that I didn't try to resolve yet. I've attached the dmesg output from a kernel compiled from usb-next (571bb7a: Revert "USB: chipidea: add vbus detect for udc") with CONFIG_USB_DEBUG=y. I booted the kernel and immediately started a suspend-to-disk (around 50-51s). As soon as the image started being written to disk, I canceled it and the system resumed (at 52s). These messages look relevant: [ 52.899290] usb 1-1.4: link qh1-0e01/ffff880230cb97c0 start 0 [1/2 us] [ 52.899345] hub 1-1:1.0: port 5 status 0000.0100 after resume, -19 [ 52.899347] usb 1-1.5: can't resume, status -19 [ 52.899348] hub 1-1:1.0: logical disconnect on port 5 Any idea how to fix this? Do you need any other info? Gr. Matthijs
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.9.0-rc4+ (matthijs@grubby) (gcc version 4.7.2 (Debian 4.7.2-5) ) #90 SMP Sat Mar 30 22:09:24 CET 2013 [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.9.0-rc4+ root=/dev/mapper/Grubby-root ro quiet [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000d2000-0x00000000000d3fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000dc000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bb27bfff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bb27c000-0x00000000bb281fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000bb282000-0x00000000bb35efff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bb35f000-0x00000000bb370fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000bb371000-0x00000000bb3f1fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bb3f2000-0x00000000bb40efff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000bb40f000-0x00000000bb46efff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bb46f000-0x00000000bb667fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000bb668000-0x00000000bb6e7fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bb6e8000-0x00000000bb70efff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000bb70f000-0x00000000bb716fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bb717000-0x00000000bb71efff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000bb71f000-0x00000000bb76afff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bb76b000-0x00000000bb776fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bb777000-0x00000000bb779fff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000bb77a000-0x00000000bb780fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bb781000-0x00000000bb781fff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000bb782000-0x00000000bb78afff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bb78b000-0x00000000bb78bfff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000bb78c000-0x00000000bb79efff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bb79f000-0x00000000bb7fefff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000bb7ff000-0x00000000bb7fffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bb800000-0x00000000bfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feaff000-0x00000000feafffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec0ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed003ff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed8ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000001fbffffff] usable [ 0.000000] BIOS-e820: [mem 0x0000000200000000-0x000000023bffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: LENOVO 3323A2G/3323A2G, BIOS 6QET69WW (1.39 ) 04/26/2012 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x23c000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-D3FFF write-protect [ 0.000000] D4000-DBFFF uncachable [ 0.000000] DC000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 disabled [ 0.000000] 1 base 000000000 mask F80000000 write-back [ 0.000000] 2 base 080000000 mask FC0000000 write-back [ 0.000000] 3 base 100000000 mask F00000000 write-back [ 0.000000] 4 base 200000000 mask FC0000000 write-back [ 0.000000] 5 base 23C000000 mask FFC000000 uncachable [ 0.000000] 6 base 0BC000000 mask FFC000000 uncachable [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] e820: update [mem 0xbc000000-0xffffffff] usable ==> reserved [ 0.000000] e820: last_pfn = 0xbb800 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f6910-0x000f691f] mapped at [ffff8800000f6910] [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] BRK [0x01a58000, 0x01a58fff] PGTABLE [ 0.000000] BRK [0x01a59000, 0x01a59fff] PGTABLE [ 0.000000] BRK [0x01a5a000, 0x01a5afff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x23be00000-0x23bffffff] [ 0.000000] [mem 0x23be00000-0x23bffffff] page 2M [ 0.000000] BRK [0x01a5b000, 0x01a5bfff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x238000000-0x23bdfffff] [ 0.000000] [mem 0x238000000-0x23bdfffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x200000000-0x237ffffff] [ 0.000000] [mem 0x200000000-0x237ffffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x00100000-0xbb27bfff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0xbb1fffff] page 2M [ 0.000000] [mem 0xbb200000-0xbb27bfff] page 4k [ 0.000000] init_memory_mapping: [mem 0xbb282000-0xbb35efff] [ 0.000000] [mem 0xbb282000-0xbb35efff] page 4k [ 0.000000] init_memory_mapping: [mem 0xbb40f000-0xbb46efff] [ 0.000000] [mem 0xbb40f000-0xbb46efff] page 4k [ 0.000000] BRK [0x01a5c000, 0x01a5cfff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0xbb70f000-0xbb716fff] [ 0.000000] [mem 0xbb70f000-0xbb716fff] page 4k [ 0.000000] init_memory_mapping: [mem 0xbb71f000-0xbb76afff] [ 0.000000] [mem 0xbb71f000-0xbb76afff] page 4k [ 0.000000] init_memory_mapping: [mem 0xbb7ff000-0xbb7fffff] [ 0.000000] [mem 0xbb7ff000-0xbb7fffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x100000000-0x1fbffffff] [ 0.000000] [mem 0x100000000-0x1fbffffff] page 2M [ 0.000000] RAMDISK: [mem 0x3789c000-0x37c45fff] [ 0.000000] ACPI: RSDP 00000000000f68e0 00024 (v02 LENOVO) [ 0.000000] ACPI: XSDT 00000000bb7f0826 0009C (v01 LENOVO TP-6Q 00001390 LTP 00000000) [ 0.000000] ACPI: FACP 00000000bb7f0900 000F4 (v04 LENOVO TP-6Q 00001390 LNVO 00000001) [ 0.000000] ACPI: DSDT 00000000bb7f0c6b 0DE70 (v01 LENOVO TP-6Q 00001390 MSFT 03000001) [ 0.000000] ACPI: FACS 00000000bb6e7000 00040 [ 0.000000] ACPI: SSDT 00000000bb7f0ab4 001B7 (v01 LENOVO TP-6Q 00001390 MSFT 03000001) [ 0.000000] ACPI: ECDT 00000000bb7feadb 00052 (v01 LENOVO TP-6Q 00001390 LNVO 00000001) [ 0.000000] ACPI: APIC 00000000bb7feb2d 00084 (v01 LENOVO TP-6Q 00001390 LNVO 00000001) [ 0.000000] ACPI: MCFG 00000000bb7febe9 0003C (v01 LENOVO TP-6Q 00001390 LNVO 00000001) [ 0.000000] ACPI: HPET 00000000bb7fec25 00038 (v01 LENOVO TP-6Q 00001390 LNVO 00000001) [ 0.000000] ACPI: ASF! 00000000bb7fedbe 000A4 (v16 LENOVO TP-6Q 00001390 PTL 00000001) [ 0.000000] ACPI: SLIC 00000000bb7fee62 00176 (v01 LENOVO TP-6Q 00001390 LTP 00000000) [ 0.000000] ACPI: BOOT 00000000bb7fefd8 00028 (v01 LENOVO TP-6Q 00001390 LTP 00000001) [ 0.000000] ACPI: SSDT 00000000bb6e590a 0085B (v01 LENOVO TP-6Q 00001390 INTL 20050513) [ 0.000000] ACPI: TCPA 00000000bb78b000 00032 (v02 PTL CRESTLN 06040000 00005A52) [ 0.000000] ACPI: DMAR 00000000bb781000 000B8 (v01 INTEL CP_DALE 00000001 INTL 00000001) [ 0.000000] ACPI: SSDT 00000000bb779000 009F1 (v01 PmRef CpuPm 00003000 INTL 20050513) [ 0.000000] ACPI: SSDT 00000000bb778000 00259 (v01 PmRef Cpu0Tst 00003000 INTL 20050513) [ 0.000000] ACPI: SSDT 00000000bb777000 0049F (v01 PmRef ApTst 00003000 INTL 20050513) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000023bffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x23bffffff] [ 0.000000] NODE_DATA [mem 0x23bff4000-0x23bff7fff] [ 0.000000] [ffffea0000000000-ffffea0007dfffff] PMD -> [ffff880233600000-ffff88023a5fffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x23bffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0009dfff] [ 0.000000] node 0: [mem 0x00100000-0xbb27bfff] [ 0.000000] node 0: [mem 0xbb282000-0xbb35efff] [ 0.000000] node 0: [mem 0xbb40f000-0xbb46efff] [ 0.000000] node 0: [mem 0xbb70f000-0xbb716fff] [ 0.000000] node 0: [mem 0xbb71f000-0xbb76afff] [ 0.000000] node 0: [mem 0xbb7ff000-0xbb7fffff] [ 0.000000] node 0: [mem 0x100000000-0x1fbffffff] [ 0.000000] node 0: [mem 0x200000000-0x23bffffff] [ 0.000000] On node 0 totalpages: 2044843 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3997 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 10431 pages used for memmap [ 0.000000] DMA32 zone: 762894 pages, LIFO batch:31 [ 0.000000] Normal zone: 17696 pages used for memmap [ 0.000000] Normal zone: 1277952 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000 [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000 [ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000 [ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000 [ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bb27c000 - 00000000bb282000 [ 0.000000] PM: Registered nosave memory: 00000000bb35f000 - 00000000bb371000 [ 0.000000] PM: Registered nosave memory: 00000000bb371000 - 00000000bb3f2000 [ 0.000000] PM: Registered nosave memory: 00000000bb3f2000 - 00000000bb40f000 [ 0.000000] PM: Registered nosave memory: 00000000bb46f000 - 00000000bb668000 [ 0.000000] PM: Registered nosave memory: 00000000bb668000 - 00000000bb6e8000 [ 0.000000] PM: Registered nosave memory: 00000000bb6e8000 - 00000000bb70f000 [ 0.000000] PM: Registered nosave memory: 00000000bb717000 - 00000000bb71f000 [ 0.000000] PM: Registered nosave memory: 00000000bb76b000 - 00000000bb777000 [ 0.000000] PM: Registered nosave memory: 00000000bb777000 - 00000000bb77a000 [ 0.000000] PM: Registered nosave memory: 00000000bb77a000 - 00000000bb781000 [ 0.000000] PM: Registered nosave memory: 00000000bb781000 - 00000000bb782000 [ 0.000000] PM: Registered nosave memory: 00000000bb782000 - 00000000bb78b000 [ 0.000000] PM: Registered nosave memory: 00000000bb78b000 - 00000000bb78c000 [ 0.000000] PM: Registered nosave memory: 00000000bb78c000 - 00000000bb79f000 [ 0.000000] PM: Registered nosave memory: 00000000bb79f000 - 00000000bb7ff000 [ 0.000000] PM: Registered nosave memory: 00000000bb800000 - 00000000c0000000 [ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000 [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000 [ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000feaff000 [ 0.000000] PM: Registered nosave memory: 00000000feaff000 - 00000000feb00000 [ 0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000fec00000 [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000 [ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000 [ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed1c000 [ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000 [ 0.000000] PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000 [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000 [ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000 [ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000 [ 0.000000] PM: Registered nosave memory: 00000001fc000000 - 0000000200000000 [ 0.000000] e820: [mem 0xc0000000-0xdfffffff] available for PCI devices [ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88023bc00000 s80384 r8192 d22016 u524288 [ 0.000000] pcpu-alloc: s80384 r8192 d22016 u524288 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2016639 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.9.0-rc4+ root=/dev/mapper/Grubby-root ro quiet [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 7983448k/9371648k available (4412k kernel code, 1192276k absent, 195924k reserved, 4352k data, 972k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. [ 0.000000] NR_IRQS:33024 nr_irqs:712 16 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.004000] tsc: Detected 2659.953 MHz processor [ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 5319.90 BogoMIPS (lpj=10639812) [ 0.000004] pid_max: default: 32768 minimum: 301 [ 0.000030] Security Framework initialized [ 0.000034] SELinux: Disabled at boot. [ 0.000435] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002391] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003242] Mount-cache hash table entries: 256 [ 0.003407] Initializing cgroup subsys cpuacct [ 0.003410] Initializing cgroup subsys devices [ 0.003411] Initializing cgroup subsys freezer [ 0.003412] Initializing cgroup subsys net_cls [ 0.003414] Initializing cgroup subsys blkio [ 0.003436] CPU: Physical Processor ID: 0 [ 0.003437] CPU: Processor Core ID: 0 [ 0.003442] mce: CPU supports 9 MCE banks [ 0.003452] CPU0: Thermal monitoring enabled (TM1) [ 0.003461] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7 [ 0.003461] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32 [ 0.003461] tlb_flushall_shift: 6 [ 0.003523] Freeing SMP alternatives: 16k freed [ 0.003530] ACPI: Core revision 20130117 [ 0.009950] ACPI: All ACPI Tables successfully acquired [ 0.027236] ftrace: allocating 17545 entries in 69 pages [ 0.034852] dmar: Host address width 36 [ 0.034854] dmar: DRHD base: 0x000000fed90000 flags: 0x0 [ 0.034861] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c9008020e30272 ecap 1000 [ 0.034862] dmar: DRHD base: 0x000000fed91000 flags: 0x0 [ 0.034866] dmar: IOMMU 1: reg_base_addr fed91000 ver 1:0 cap c0000020230272 ecap 1000 [ 0.034867] dmar: DRHD base: 0x000000fed93000 flags: 0x1 [ 0.034872] dmar: IOMMU 2: reg_base_addr fed93000 ver 1:0 cap c9008020630272 ecap 1000 [ 0.034873] dmar: RMRR base: 0x000000bb6e9000 end: 0x000000bb6fffff [ 0.034874] dmar: RMRR base: 0x000000bdc00000 end: 0x000000bfffffff [ 0.035496] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.075182] smpboot: CPU0: Intel(R) Core(TM) i7 CPU M 620 @ 2.67GHz (fam: 06, model: 25, stepping: 02) [ 0.181733] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere events, Intel PMU driver. [ 0.181739] perf_event_intel: CPUID marked event: 'bus cycles' unavailable [ 0.181741] ... version: 3 [ 0.181741] ... bit width: 48 [ 0.181742] ... generic registers: 4 [ 0.181743] ... value mask: 0000ffffffffffff [ 0.181744] ... max period: 000000007fffffff [ 0.181745] ... fixed-purpose events: 3 [ 0.181745] ... event mask: 000000070000000f [ 0.195203] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.181985] smpboot: Booting Node 0, Processors #1 #2 #3 OK [ 0.221729] Brought up 4 CPUs [ 0.221740] smpboot: Total of 4 processors activated (21279.62 BogoMIPS) [ 0.223791] devtmpfs: initialized [ 0.224891] PM: Registering ACPI NVS region [mem 0xbb371000-0xbb3f1fff] (528384 bytes) [ 0.224905] PM: Registering ACPI NVS region [mem 0xbb668000-0xbb6e7fff] (524288 bytes) [ 0.224918] PM: Registering ACPI NVS region [mem 0xbb76b000-0xbb776fff] (49152 bytes) [ 0.224920] PM: Registering ACPI NVS region [mem 0xbb77a000-0xbb780fff] (28672 bytes) [ 0.224922] PM: Registering ACPI NVS region [mem 0xbb782000-0xbb78afff] (36864 bytes) [ 0.224923] PM: Registering ACPI NVS region [mem 0xbb78c000-0xbb79efff] (77824 bytes) [ 0.225027] regulator-dummy: no parameters [ 0.225080] NET: Registered protocol family 16 [ 0.225146] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.225147] ACPI: bus type PCI registered [ 0.225184] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.225186] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820 [ 0.252824] PCI: Using configuration type 1 for base access [ 0.253263] bio: create slab <bio-0> at 0 [ 0.253331] ACPI: Added _OSI(Module Device) [ 0.253332] ACPI: Added _OSI(Processor Device) [ 0.253334] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.253335] ACPI: Added _OSI(Processor Aggregator Device) [ 0.254477] ACPI: EC: EC description table is found, configuring boot EC [ 0.258205] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 0.335625] ACPI: SSDT 00000000bb71a598 004F3 (v01 PmRef Cpu0Ist 00003000 INTL 20050513) [ 0.335896] ACPI: Dynamic OEM Table Load: [ 0.335898] ACPI: SSDT (null) 004F3 (v01 PmRef Cpu0Ist 00003000 INTL 20050513) [ 0.335985] ACPI: SSDT 00000000bb718718 006B2 (v01 PmRef Cpu0Cst 00003001 INTL 20050513) [ 0.336268] ACPI: Dynamic OEM Table Load: [ 0.336269] ACPI: SSDT (null) 006B2 (v01 PmRef Cpu0Cst 00003001 INTL 20050513) [ 0.336494] ACPI: SSDT 00000000bb719a98 00303 (v01 PmRef ApIst 00003000 INTL 20050513) [ 0.336807] ACPI: Dynamic OEM Table Load: [ 0.336809] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20050513) [ 0.336888] ACPI: SSDT 00000000bb717d98 00119 (v01 PmRef ApCst 00003000 INTL 20050513) [ 0.337170] ACPI: Dynamic OEM Table Load: [ 0.337172] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20050513) [ 0.338668] ACPI: Interpreter enabled [ 0.338674] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568) [ 0.338677] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568) [ 0.338686] ACPI: (supports S0 S3 S4 S5) [ 0.338688] ACPI: Using IOAPIC for interrupt routing [ 0.338710] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.343405] ACPI: Power Resource [PUBS] (on) [ 0.346499] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11) [ 0.346577] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11) [ 0.346637] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. [ 0.346714] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11) [ 0.346790] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11) [ 0.346849] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. [ 0.346908] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. [ 0.346985] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11) [ 0.347017] ACPI: PCI Root Bridge [UNCR] (domain 0000 [bus ff]) [ 0.347021] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM [ 0.347022] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08) [ 0.347047] PCI host bridge to bus 0000:ff [ 0.347049] pci_bus 0000:ff: root bus resource [bus ff] [ 0.347056] pci 0000:ff:00.0: [8086:2c62] type 00 class 0x060000 [ 0.347093] pci 0000:ff:00.1: [8086:2d01] type 00 class 0x060000 [ 0.347126] pci 0000:ff:02.0: [8086:2d10] type 00 class 0x060000 [ 0.347160] pci 0000:ff:02.1: [8086:2d11] type 00 class 0x060000 [ 0.347189] pci 0000:ff:02.2: [8086:2d12] type 00 class 0x060000 [ 0.347218] pci 0000:ff:02.3: [8086:2d13] type 00 class 0x060000 [ 0.347254] ACPI _OSC control for PCIe not granted, disabling ASPM [ 0.347272] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.347434] acpi PNP0A08:00: Requesting ACPI _OSC control (0x1d) [ 0.347581] acpi PNP0A08:00: ACPI _OSC request failed (AE_SUPPORT), returned control mask: 0x0d [ 0.347622] PCI host bridge to bus 0000:00 [ 0.347624] pci_bus 0000:00: root bus resource [bus 00-fe] [ 0.347626] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7] [ 0.347627] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff] [ 0.347629] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff] [ 0.347630] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff] [ 0.347632] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff] [ 0.347633] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff] [ 0.347638] pci 0000:00:00.0: [8086:0044] type 00 class 0x060000 [ 0.347651] DMAR: Disabling batched IOTLB flush on Ironlake [ 0.347699] pci 0000:00:02.0: [8086:0046] type 00 class 0x030000 [ 0.347708] pci 0000:00:02.0: reg 10: [mem 0xf2000000-0xf23fffff 64bit] [ 0.347713] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.347717] pci 0000:00:02.0: reg 20: [io 0x1800-0x1807] [ 0.347794] pci 0000:00:16.0: [8086:3b64] type 00 class 0x078000 [ 0.347823] pci 0000:00:16.0: reg 10: [mem 0xf2727800-0xf272780f 64bit] [ 0.347916] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold [ 0.347983] pci 0000:00:16.3: [8086:3b67] type 00 class 0x070002 [ 0.348006] pci 0000:00:16.3: reg 10: [io 0x1808-0x180f] [ 0.348017] pci 0000:00:16.3: reg 14: [mem 0xf2524000-0xf2524fff] [ 0.348173] pci 0000:00:19.0: [8086:10ea] type 00 class 0x020000 [ 0.348197] pci 0000:00:19.0: reg 10: [mem 0xf2500000-0xf251ffff] [ 0.348207] pci 0000:00:19.0: reg 14: [mem 0xf2525000-0xf2525fff] [ 0.348218] pci 0000:00:19.0: reg 18: [io 0x1820-0x183f] [ 0.348305] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 0.348331] pci 0000:00:19.0: System wakeup disabled by ACPI [ 0.348365] pci 0000:00:1a.0: [8086:3b3c] type 00 class 0x0c0320 [ 0.348390] pci 0000:00:1a.0: reg 10: [mem 0xf2728000-0xf27283ff] [ 0.348498] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 0.348534] pci 0000:00:1a.0: System wakeup disabled by ACPI [ 0.348569] pci 0000:00:1b.0: [8086:3b56] type 00 class 0x040300 [ 0.348589] pci 0000:00:1b.0: reg 10: [mem 0xf2520000-0xf2523fff 64bit] [ 0.348683] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.348727] pci 0000:00:1b.0: System wakeup disabled by ACPI [ 0.348757] pci 0000:00:1c.0: [8086:3b42] type 01 class 0x060400 [ 0.348856] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.348886] pci 0000:00:1c.0: System wakeup disabled by ACPI [ 0.348918] pci 0000:00:1c.3: [8086:3b48] type 01 class 0x060400 [ 0.349015] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold [ 0.349048] pci 0000:00:1c.3: System wakeup disabled by ACPI [ 0.349078] pci 0000:00:1c.4: [8086:3b4a] type 01 class 0x060400 [ 0.349176] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.349210] pci 0000:00:1c.4: System wakeup disabled by ACPI [ 0.349248] pci 0000:00:1d.0: [8086:3b34] type 00 class 0x0c0320 [ 0.349272] pci 0000:00:1d.0: reg 10: [mem 0xf2728400-0xf27287ff] [ 0.349378] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 0.349412] pci 0000:00:1d.0: System wakeup disabled by ACPI [ 0.349440] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401 [ 0.349552] pci 0000:00:1f.0: [8086:3b07] type 00 class 0x060100 [ 0.349696] pci 0000:00:1f.2: [8086:3b2f] type 00 class 0x010601 [ 0.349722] pci 0000:00:1f.2: reg 10: [io 0x1860-0x1867] [ 0.349732] pci 0000:00:1f.2: reg 14: [io 0x1814-0x1817] [ 0.349743] pci 0000:00:1f.2: reg 18: [io 0x1818-0x181f] [ 0.349754] pci 0000:00:1f.2: reg 1c: [io 0x1810-0x1813] [ 0.349765] pci 0000:00:1f.2: reg 20: [io 0x1840-0x185f] [ 0.349775] pci 0000:00:1f.2: reg 24: [mem 0xf2727000-0xf27277ff] [ 0.349841] pci 0000:00:1f.2: PME# supported from D3hot [ 0.349896] pci 0000:00:1f.3: [8086:3b30] type 00 class 0x0c0500 [ 0.349917] pci 0000:00:1f.3: reg 10: [mem 0xf2728800-0xf27288ff 64bit] [ 0.349945] pci 0000:00:1f.3: reg 20: [io 0x1880-0x189f] [ 0.350023] pci 0000:00:1f.6: [8086:3b32] type 00 class 0x118000 [ 0.350049] pci 0000:00:1f.6: reg 10: [mem 0xf2526000-0xf2526fff 64bit] [ 0.350240] pci 0000:00:1c.0: PCI bridge to [bus 0d] [ 0.350313] pci 0000:00:1c.3: PCI bridge to [bus 05-0c] [ 0.350318] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff] [ 0.350322] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff] [ 0.350329] pci 0000:00:1c.3: bridge window [mem 0xf2800000-0xf28fffff 64bit pref] [ 0.350450] pci 0000:02:00.0: [8086:4238] type 00 class 0x028000 [ 0.350508] pci 0000:02:00.0: reg 10: [mem 0xf2400000-0xf2401fff 64bit] [ 0.350734] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.359248] pci 0000:00:1c.4: PCI bridge to [bus 02] [ 0.359256] pci 0000:00:1c.4: bridge window [mem 0xf2400000-0xf24fffff] [ 0.359342] pci 0000:00:1e.0: PCI bridge to [bus 0e] (subtractive decode) [ 0.359354] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 0.359355] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 0.359357] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 0.359359] pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode) [ 0.359360] pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode) [ 0.359361] pci 0000:00:1e.0: bridge window [mem 0xc0000000-0xfebfffff] (subtractive decode) [ 0.359385] ACPI _OSC control for PCIe not granted, disabling ASPM [ 0.360383] ACPI: Enabled 3 GPEs in block 00 to 3F [ 0.360392] acpi root: \_SB_.UNCR notify handler is installed [ 0.360395] acpi root: \_SB_.PCI0 notify handler is installed [ 0.360422] Found 2 acpi root devices [ 0.360477] ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62 [ 0.361385] ACPI: ACPI Dock Station Driver: 3 docks/bays found [ 0.361434] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 0.361437] vgaarb: loaded [ 0.361437] vgaarb: bridge control possible 0000:00:02.0 [ 0.361456] PCI: Using ACPI for IRQ routing [ 0.371224] PCI: pci_cache_line_size set to 64 bytes [ 0.371323] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff] [ 0.371324] e820: reserve RAM buffer [mem 0xbb27c000-0xbbffffff] [ 0.371327] e820: reserve RAM buffer [mem 0xbb35f000-0xbbffffff] [ 0.371329] e820: reserve RAM buffer [mem 0xbb46f000-0xbbffffff] [ 0.371331] e820: reserve RAM buffer [mem 0xbb717000-0xbbffffff] [ 0.371333] e820: reserve RAM buffer [mem 0xbb76b000-0xbbffffff] [ 0.371334] e820: reserve RAM buffer [mem 0xbb800000-0xbbffffff] [ 0.371427] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0 [ 0.371431] hpet0: 8 comparators, 64-bit 14.318180 MHz counter [ 0.373443] Switching to clocksource hpet [ 0.374614] pnp: PnP ACPI init [ 0.374624] ACPI: bus type PNP registered [ 0.375191] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.375193] system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved [ 0.375195] system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved [ 0.375197] system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved [ 0.375198] system 00:00: [mem 0x000cc000-0x000cffff] has been reserved [ 0.375200] system 00:00: [mem 0x000d0000-0x000d3fff] could not be reserved [ 0.375202] system 00:00: [mem 0x000dc000-0x000dffff] could not be reserved [ 0.375203] system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved [ 0.375205] system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved [ 0.375207] system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved [ 0.375208] system 00:00: [mem 0x000ec000-0x000effff] could not be reserved [ 0.375210] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.375212] system 00:00: [mem 0x00100000-0xbfffffff] could not be reserved [ 0.375214] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved [ 0.375216] system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved [ 0.375218] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.375509] system 00:01: [io 0x164e-0x164f] has been reserved [ 0.375511] system 00:01: [io 0x1000-0x107f] has been reserved [ 0.375513] system 00:01: [io 0x1180-0x11ff] has been reserved [ 0.375515] system 00:01: [io 0x0800-0x080f] has been reserved [ 0.375517] system 00:01: [io 0x15e0-0x15ef] has been reserved [ 0.375519] system 00:01: [io 0x1600-0x1641] has been reserved [ 0.375520] system 00:01: [io 0x1644-0x167f] could not be reserved [ 0.375523] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.375524] system 00:01: [mem 0xfeaff000-0xfeafffff] has been reserved [ 0.375526] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.375528] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved [ 0.375530] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.375531] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.375533] system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved [ 0.375535] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.375572] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.375579] pnp 00:03: [dma 4] [ 0.375592] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.375608] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.375633] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.375655] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.375675] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.375697] pnp 00:08: Plug and Play ACPI device, IDs LEN0018 PNP0f13 (active) [ 0.375944] pnp 00:09: Plug and Play ACPI device, IDs SMO1200 PNP0c31 (active) [ 0.376427] pnp: PnP ACPI: found 10 devices [ 0.376428] ACPI: bus type PNP unregistered [ 0.382844] pci 0000:00:1c.0: PCI bridge to [bus 0d] [ 0.382859] pci 0000:00:1c.3: PCI bridge to [bus 05-0c] [ 0.382862] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff] [ 0.382868] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff] [ 0.382872] pci 0000:00:1c.3: bridge window [mem 0xf2800000-0xf28fffff 64bit pref] [ 0.382879] pci 0000:00:1c.4: PCI bridge to [bus 02] [ 0.382884] pci 0000:00:1c.4: bridge window [mem 0xf2400000-0xf24fffff] [ 0.382894] pci 0000:00:1e.0: PCI bridge to [bus 0e] [ 0.383019] pci 0000:00:1e.0: setting latency timer to 64 [ 0.383024] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.383025] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.383026] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.383028] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff] [ 0.383029] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff] [ 0.383031] pci_bus 0000:00: resource 9 [mem 0xc0000000-0xfebfffff] [ 0.383032] pci_bus 0000:05: resource 0 [io 0x2000-0x2fff] [ 0.383034] pci_bus 0000:05: resource 1 [mem 0xf0000000-0xf1ffffff] [ 0.383035] pci_bus 0000:05: resource 2 [mem 0xf2800000-0xf28fffff 64bit pref] [ 0.383036] pci_bus 0000:02: resource 1 [mem 0xf2400000-0xf24fffff] [ 0.383038] pci_bus 0000:0e: resource 4 [io 0x0000-0x0cf7] [ 0.383039] pci_bus 0000:0e: resource 5 [io 0x0d00-0xffff] [ 0.383041] pci_bus 0000:0e: resource 6 [mem 0x000a0000-0x000bffff] [ 0.383042] pci_bus 0000:0e: resource 7 [mem 0x000d4000-0x000d7fff] [ 0.383043] pci_bus 0000:0e: resource 8 [mem 0x000d8000-0x000dbfff] [ 0.383045] pci_bus 0000:0e: resource 9 [mem 0xc0000000-0xfebfffff] [ 0.383108] NET: Registered protocol family 2 [ 0.383329] TCP established hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.383633] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.383886] TCP: Hash tables configured (established 65536 bind 65536) [ 0.383916] TCP: reno registered [ 0.383926] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.383978] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.384099] NET: Registered protocol family 1 [ 0.384117] pci 0000:00:02.0: Boot video device [ 0.384342] PCI: CLS 64 bytes, default 64 [ 0.384383] Unpacking initramfs... [ 0.439045] Freeing initrd memory: 3752k freed [ 0.439733] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.439738] software IO TLB [mem 0xb727c000-0xbb27c000] (64MB) mapped at [ffff8800b727c000-ffff8800bb27bfff] [ 0.439766] Simple Boot Flag at 0x35 set to 0x1 [ 0.440115] audit: initializing netlink socket (disabled) [ 0.440132] type=2000 audit(1364679079.252:1): initialized [ 0.451452] bounce pool size: 64 pages [ 0.451457] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.452231] VFS: Disk quotas dquot_6.5.2 [ 0.452255] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.452339] msgmni has been set to 15600 [ 0.452541] alg: No test for stdrng (krng) [ 0.452566] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.452568] io scheduler noop registered [ 0.452569] io scheduler deadline registered [ 0.452589] io scheduler cfq registered (default) [ 0.452850] intel_idle: MWAIT substates: 0x1120 [ 0.452851] intel_idle: v0.4 model 0x25 [ 0.452852] intel_idle: lapic_timer_reliable_states 0xffffffff [ 0.452918] GHES: HEST is not enabled! [ 0.453041] Linux agpgart interface v0.103 [ 0.453087] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset [ 0.453163] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.454048] agpgart-intel 0000:00:00.0: detected 32768K stolen memory [ 0.454201] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.454282] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 0.458220] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.458226] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.458335] mousedev: PS/2 mouse device common for all mice [ 0.458370] rtc_cmos 00:06: RTC can wake from S4 [ 0.458502] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 [ 0.458533] rtc_cmos 00:06: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 0.458604] cpuidle: using governor ladder [ 0.458678] cpuidle: using governor menu [ 0.458711] drop_monitor: Initializing network drop monitor service [ 0.458778] TCP: cubic registered [ 0.458888] NET: Registered protocol family 10 [ 0.459080] mip6: Mobile IPv6 [ 0.459083] NET: Registered protocol family 17 [ 0.459092] Key type dns_resolver registered [ 0.459342] PM: Hibernation image not present or could not be loaded. [ 0.459352] registered taskstats version 1 [ 0.460883] Freeing unused kernel memory: 972k freed [ 0.461049] Write protecting the kernel read-only data: 8192k [ 0.462804] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 0.463895] Freeing unused kernel memory: 1720k freed [ 0.465133] Freeing unused kernel memory: 664k freed [ 0.521047] udevd[69]: starting version 175 [ 0.542594] SCSI subsystem initialized [ 0.543722] ACPI: bus type ATA registered [ 0.543745] libata version 3.00 loaded. [ 0.550383] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.550389] ACPI: Thermal Zone [THM0] (59 C) [ 0.556623] ahci 0000:00:1f.2: version 3.0 [ 0.557077] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X [ 0.557126] ahci: SSS flag set, parallel bus scan disabled [ 0.557182] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x33 impl SATA mode [ 0.557186] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part ems sxs apst [ 0.557192] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.577976] scsi0 : ahci [ 0.578172] scsi1 : ahci [ 0.578254] scsi2 : ahci [ 0.578370] scsi3 : ahci [ 0.578530] scsi4 : ahci [ 0.578679] scsi5 : ahci [ 0.578724] ata1: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727100 irq 40 [ 0.578727] ata2: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727180 irq 40 [ 0.578728] ata3: DUMMY [ 0.578729] ata4: DUMMY [ 0.578732] ata5: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727300 irq 40 [ 0.578735] ata6: SATA max UDMA/133 abar m2048@0xf2727000 port 0xf2727380 irq 40 [ 0.897610] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.898204] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded [ 0.898210] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out [ 0.898214] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out [ 0.898725] ata1.00: ATA-8: INTEL SSDSA2CW300G3, 4PC10302, max UDMA/133 [ 0.898730] ata1.00: 586072368 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 0.899351] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded [ 0.899357] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out [ 0.899361] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out [ 0.899776] ata1.00: configured for UDMA/133 [ 0.900089] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW30 4PC1 PQ: 0 ANSI: 5 [ 1.217640] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.220469] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded [ 1.221322] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded [ 1.222942] ata2.00: ATAPI: MATSHITADVD-RAM UJ892, SB01, max UDMA/100 [ 1.226456] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded [ 1.227356] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded [ 1.229048] ata2.00: configured for UDMA/100 [ 1.232714] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ892 SB01 PQ: 0 ANSI: 5 [ 1.437652] tsc: Refined TSC clocksource calibration: 2659.999 MHz [ 1.437659] Switching to clocksource tsc [ 1.549692] ata5: SATA link down (SStatus 0 SControl 300) [ 1.869689] ata6: SATA link down (SStatus 0 SControl 300) [ 1.873682] sd 0:0:0:0: [sda] 586072368 512-byte logical blocks: (300 GB/279 GiB) [ 1.873723] sd 0:0:0:0: [sda] Write Protect is off [ 1.873725] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.873735] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.874073] sda: sda1 sda2 sda3 [ 1.874305] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.938932] device-mapper: uevent: version 1.0.3 [ 1.939033] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@xxxxxxxxxx [ 1.961131] bio: create slab <bio-1> at 1 [ 2.038233] PM: Starting manual resume from disk [ 2.038240] PM: Hibernation image partition 254:1 present [ 2.038242] PM: Looking for hibernation image. [ 2.038529] PM: Image not found (code -22) [ 2.038533] PM: Hibernation image not present or could not be loaded. [ 2.042462] PM: Marking nosave pages: [mem 0x0009e000-0x000fffff] [ 2.042471] PM: Marking nosave pages: [mem 0xbb27c000-0xbb281fff] [ 2.042474] PM: Marking nosave pages: [mem 0xbb35f000-0xbb40efff] [ 2.042481] PM: Marking nosave pages: [mem 0xbb46f000-0xbb70efff] [ 2.042503] PM: Marking nosave pages: [mem 0xbb717000-0xbb71efff] [ 2.042506] PM: Marking nosave pages: [mem 0xbb76b000-0xbb7fefff] [ 2.042512] PM: Marking nosave pages: [mem 0xbb800000-0xffffffff] [ 2.044354] PM: Marking nosave pages: [mem 0x1fc000000-0x1ffffffff] [ 2.044822] PM: Basic memory bitmaps created [ 2.104996] PM: Basic memory bitmaps freed [ 2.120013] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 2.417442] udevd[400]: starting version 175 [ 2.529467] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1 [ 2.529658] ACPI: Lid Switch [LID] [ 2.529720] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2 [ 2.529726] ACPI: Sleep Button [SLPB] [ 2.529789] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 2.529792] ACPI: Power Button [PWRF] [ 2.531130] ACPI: Requesting acpi_cpufreq [ 2.535333] ACPI: bus type USB registered [ 2.535366] usbcore: registered new interface driver usbfs [ 2.535377] usbcore: registered new interface driver hub [ 2.537619] usbcore: registered new device driver usb [ 2.540315] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.540321] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 2.541358] ehci-pci: EHCI PCI platform driver [ 2.541500] pps_core: LinuxPPS API ver. 1 registered [ 2.541502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx> [ 2.541505] ehci-pci 0000:00:1a.0: setting latency timer to 64 [ 2.541523] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 2.541532] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 2.541550] ehci-pci 0000:00:1a.0: debug port 2 [ 2.541556] ehci-pci 0000:00:1a.0: reset hcs_params 0x200003 dbg=2 cc=0 pcc=0 ordered !ppc ports=3 [ 2.541559] ehci-pci 0000:00:1a.0: reset hcc_params 36881 caching frame 1024 64 bit addr [ 2.541584] ehci-pci 0000:00:1a.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 2.545634] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported [ 2.545674] ehci-pci 0000:00:1a.0: supports USB remote wakeup [ 2.545704] ehci-pci 0000:00:1a.0: irq 23, io mem 0xf2728000 [ 2.545711] ehci-pci 0000:00:1a.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 2.545812] PTP clock support registered [ 2.553083] [drm] Initialized drm 1.1.0 20060810 [ 2.553230] e1000e: Intel(R) PRO/1000 Network Driver - 2.2.14-k [ 2.553232] e1000e: Copyright(c) 1999 - 2013 Intel Corporation. [ 2.557704] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.557745] usb usb1: default language 0x0409 [ 2.557752] usb usb1: udev 1, busnum 1, minor = 0 [ 2.557755] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.557757] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.557759] usb usb1: Product: EHCI Host Controller [ 2.557760] usb usb1: Manufacturer: Linux 3.9.0-rc4+ ehci_hcd [ 2.557762] usb usb1: SerialNumber: 0000:00:1a.0 [ 2.557906] usb usb1: usb_probe_device [ 2.557909] usb usb1: configuration #1 chosen from 1 choice [ 2.557919] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.557940] hub 1-0:1.0: usb_probe_interface [ 2.557942] hub 1-0:1.0: usb_probe_interface - got id [ 2.557945] hub 1-0:1.0: USB hub found [ 2.557952] hub 1-0:1.0: 3 ports detected [ 2.557954] hub 1-0:1.0: standalone hub [ 2.557955] hub 1-0:1.0: no power switching (usb 1.0) [ 2.557957] hub 1-0:1.0: individual port over-current protection [ 2.557958] hub 1-0:1.0: power on to power good time: 20ms [ 2.557962] hub 1-0:1.0: local power source is good [ 2.558021] usb usb1: usb port1's DeviceRemovable is changed to 1 according to platform information. [ 2.558024] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 2.558216] ehci-pci 0000:00:1d.0: setting latency timer to 64 [ 2.558225] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 2.558232] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.558250] ehci-pci 0000:00:1d.0: debug port 2 [ 2.558255] ehci-pci 0000:00:1d.0: reset hcs_params 0x200003 dbg=2 cc=0 pcc=0 ordered !ppc ports=3 [ 2.558259] ehci-pci 0000:00:1d.0: reset hcc_params 36881 caching frame 1024 64 bit addr [ 2.558282] ehci-pci 0000:00:1d.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 2.562195] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported [ 2.562197] ehci-pci 0000:00:1d.0: supports USB remote wakeup [ 2.564876] ehci-pci 0000:00:1d.0: irq 19, io mem 0xf2728400 [ 2.564886] ehci-pci 0000:00:1d.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 2.573928] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.573966] usb usb2: default language 0x0409 [ 2.573973] usb usb2: udev 1, busnum 2, minor = 128 [ 2.573976] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.573978] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.573980] usb usb2: Product: EHCI Host Controller [ 2.573982] usb usb2: Manufacturer: Linux 3.9.0-rc4+ ehci_hcd [ 2.573983] usb usb2: SerialNumber: 0000:00:1d.0 [ 2.574092] usb usb2: usb_probe_device [ 2.574096] usb usb2: configuration #1 chosen from 1 choice [ 2.574107] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 2.574130] hub 2-0:1.0: usb_probe_interface [ 2.574133] hub 2-0:1.0: usb_probe_interface - got id [ 2.574136] hub 2-0:1.0: USB hub found [ 2.574141] hub 2-0:1.0: 3 ports detected [ 2.574143] hub 2-0:1.0: standalone hub [ 2.574144] hub 2-0:1.0: no power switching (usb 1.0) [ 2.574146] hub 2-0:1.0: individual port over-current protection [ 2.574148] hub 2-0:1.0: power on to power good time: 20ms [ 2.574151] hub 2-0:1.0: local power source is good [ 2.574212] usb usb2: usb port1's DeviceRemovable is changed to 1 according to platform information. [ 2.574215] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 2.574308] intel ips 0000:00:1f.6: CPU TDP doesn't match expected value (found 25, expected 29) [ 2.574501] intel ips 0000:00:1f.6: failed to get i915 symbols, graphics turbo disabled until i915 loads [ 2.576263] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 2.578858] intel ips 0000:00:1f.6: IPS driver initialized, MCP temp limit 90 [ 2.579318] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt [ 2.579431] e1000e 0000:00:19.0: setting latency timer to 64 [ 2.579514] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.579563] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 2.583459] cfg80211: Calling CRDA to update world regulatory domain [ 2.586665] tpm_tis 00:09: 1.2 TPM (device-id 0x0, rev-id 78) [ 2.587381] ACPI: AC Adapter [AC] (on-line) [ 2.591443] Intel(R) Wireless WiFi driver for Linux, in-tree:d [ 2.591447] Copyright(c) 2003-2013 Intel Corporation [ 2.592125] iwlwifi 0000:02:00.0: irq 42 for MSI/MSI-X [ 2.595257] Non-volatile memory driver v1.3 [ 2.599748] thinkpad_acpi: ThinkPad ACPI Extras v0.24 [ 2.599752] thinkpad_acpi: http://ibm-acpi.sf.net/ [ 2.599753] thinkpad_acpi: ThinkPad BIOS 6QET69WW (1.39 ), EC 6QHT33WW-1.14 [ 2.599755] thinkpad_acpi: Lenovo ThinkPad X201, model 3323A2G [ 2.601557] microcode: CPU0 sig=0x20652, pf=0x10, revision=0xd [ 2.602770] sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.602773] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.603207] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.603269] thinkpad_acpi: detected a 8-level brightness capable ThinkPad [ 2.605898] thinkpad_acpi: radio switch found; radios are enabled [ 2.606617] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode [ 2.606738] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver [ 2.606740] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default... [ 2.608147] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.608285] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.609300] ACPI: Battery Slot [BAT0] (battery present) [ 2.613331] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked [ 2.616124] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one [ 2.616379] thinkpad_acpi: Console audio control enabled, mode: monitor (read only) [ 2.617791] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input5 [ 2.645722] tpm_tis 00:09: TPM is disabled/deactivated (0x6) [ 2.654540] microcode: CPU1 sig=0x20652, pf=0x10, revision=0xd [ 2.657706] ehci-pci 0000:00:1a.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 2.657716] hub 1-0:1.0: port 1: status 0501 change 0001 [ 2.662003] iwlwifi 0000:02:00.0: loaded firmware version 9.221.4.1 build 25532 [ 2.667512] microcode: CPU2 sig=0x20652, pf=0x10, revision=0xd [ 2.673159] microcode: CPU3 sig=0x20652, pf=0x10, revision=0xd [ 2.673728] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 2.673753] hub 2-0:1.0: port 1: status 0501 change 0001 [ 2.684854] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba [ 2.700717] iwlwifi 0000:02:00.0: CONFIG_IWLWIFI_DEBUG enabled [ 2.700724] iwlwifi 0000:02:00.0: CONFIG_IWLWIFI_DEBUGFS disabled [ 2.700728] iwlwifi 0000:02:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 2.700731] iwlwifi 0000:02:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE disabled [ 2.700734] iwlwifi 0000:02:00.0: CONFIG_IWLWIFI_P2P disabled [ 2.700738] iwlwifi 0000:02:00.0: Detected Intel(R) Centrino(R) Ultimate-N 6300 AGN, REV=0x74 [ 2.700793] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S [ 2.702718] cfg80211: World regulatory domain updated: [ 2.702720] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 2.702722] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 2.702723] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 2.702724] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 2.702725] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 2.702726] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 2.720285] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2.729484] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni) [ 2.752269] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 2.761936] hub 1-0:1.0: state 7 ports 3 chg 0002 evt 0000 [ 2.761951] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 2.762152] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 5c:ff:35:0f:10:5e [ 2.762155] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.762237] e1000e 0000:00:19.0 eth0: MAC: 9, PHY: 10, PBA No: A002FF-0FF [ 2.762305] ACPI Warning: 0x0000000000001028-0x000000000000102f SystemIO conflicts with Region \_SB_.PCI0.LPC_.PMIO 1 (20130117/utaddress-251) [ 2.762309] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 2.762314] ACPI Warning: 0x00000000000011c0-0x00000000000011cf SystemIO conflicts with Region \_SB_.PCI0.LPC_.LPIO 1 (20130117/utaddress-251) [ 2.762317] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 2.762319] ACPI Warning: 0x00000000000011b0-0x00000000000011bf SystemIO conflicts with Region \_SB_.PCI0.LPC_.LPIO 1 (20130117/utaddress-251) [ 2.762323] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 2.762324] ACPI Warning: 0x0000000000001180-0x00000000000011af SystemIO conflicts with Region \_SB_.PCI0.LPC_.LPIO 1 (20130117/utaddress-251) [ 2.762340] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 2.762341] lpc_ich: Resource conflict(s) found affecting gpio_ich [ 2.763024] [drm] Memory usable by graphics device = 2048M [ 2.763032] i915 0000:00:02.0: setting latency timer to 64 [ 2.797526] i915 0000:00:02.0: irq 43 for MSI/MSI-X [ 2.797537] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 2.797538] [drm] Driver supports precise vblank timestamp query. [ 2.797616] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 2.818018] ehci-pci 0000:00:1a.0: port 1 reset complete, port enabled [ 2.818029] ehci-pci 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 2.873735] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 2.889117] fbcon: inteldrmfb (fb0) is primary device [ 2.930027] ehci-pci 0000:00:1a.0: port 1 reset complete, port enabled [ 2.930035] ehci-pci 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 3.006213] usb 1-1: udev 2, busnum 1, minor = 1 [ 3.006217] usb 1-1: New USB device found, idVendor=8087, idProduct=0020 [ 3.006220] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.006413] usb 1-1: usb_probe_device [ 3.006418] usb 1-1: configuration #1 chosen from 1 choice [ 3.006622] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 3.006681] hub 1-1:1.0: usb_probe_interface [ 3.006684] hub 1-1:1.0: usb_probe_interface - got id [ 3.006689] hub 1-1:1.0: USB hub found [ 3.006803] hub 1-1:1.0: 6 ports detected [ 3.006807] hub 1-1:1.0: standalone hub [ 3.006809] hub 1-1:1.0: individual port power switching [ 3.006812] hub 1-1:1.0: individual port over-current protection [ 3.006814] hub 1-1:1.0: Single TT [ 3.006818] hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.006820] hub 1-1:1.0: Port indicators are supported [ 3.006823] hub 1-1:1.0: power on to power good time: 100ms [ 3.007103] hub 1-1:1.0: local power source is good [ 3.007424] usb 1-1: usb port3's DeviceRemovable is changed to 1 according to platform information. [ 3.007426] usb 1-1: usb port4's DeviceRemovable is changed to 1 according to platform information. [ 3.007429] usb 1-1: usb port6's DeviceRemovable is changed to 1 according to platform information. [ 3.007431] hub 1-1:1.0: enabling power on all ports [ 3.008240] hub 2-0:1.0: state 7 ports 3 chg 0002 evt 0000 [ 3.008249] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 3.062043] ehci-pci 0000:00:1d.0: port 1 reset complete, port enabled [ 3.062051] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 3.106253] hub 1-1:1.0: port 4: status 0101 change 0001 [ 3.106504] hub 1-1:1.0: port 5: status 0101 change 0001 [ 3.106720] hub 1-1:1.0: port 6: status 0101 change 0001 [ 3.117772] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 3.174052] ehci-pci 0000:00:1d.0: port 1 reset complete, port enabled [ 3.174058] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 3.205817] usb 1-1: link qh256-0001/ffff880230cb5940 start 1 [1/0 us] [ 3.250240] usb 2-1: udev 2, busnum 2, minor = 129 [ 3.250244] usb 2-1: New USB device found, idVendor=8087, idProduct=0020 [ 3.250246] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.250379] usb 2-1: usb_probe_device [ 3.250383] usb 2-1: configuration #1 chosen from 1 choice [ 3.250478] usb 2-1: adding 2-1:1.0 (config #1, interface 0) [ 3.250538] hub 2-1:1.0: usb_probe_interface [ 3.250542] hub 2-1:1.0: usb_probe_interface - got id [ 3.250546] hub 2-1:1.0: USB hub found [ 3.250719] hub 2-1:1.0: 8 ports detected [ 3.250721] hub 2-1:1.0: standalone hub [ 3.250723] hub 2-1:1.0: individual port power switching [ 3.250725] hub 2-1:1.0: individual port over-current protection [ 3.250727] hub 2-1:1.0: Single TT [ 3.250729] hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.250731] hub 2-1:1.0: Port indicators are supported [ 3.250733] hub 2-1:1.0: power on to power good time: 100ms [ 3.250956] hub 2-1:1.0: local power source is good [ 3.251400] usb 2-1: usb port3's DeviceRemovable is changed to 1 according to platform information. [ 3.251403] usb 2-1: usb port4's DeviceRemovable is changed to 1 according to platform information. [ 3.251406] usb 2-1: usb port5's DeviceRemovable is changed to 1 according to platform information. [ 3.251409] usb 2-1: usb port7's DeviceRemovable is changed to 1 according to platform information. [ 3.251413] usb 2-1: usb port8's DeviceRemovable is changed to 1 according to platform information. [ 3.251416] hub 2-1:1.0: enabling power on all ports [ 3.252543] hub 1-1:1.0: state 7 ports 6 chg 0070 evt 0000 [ 3.252721] hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s [ 3.321859] usb 1-1.4: new full-speed USB device number 3 using ehci-pci [ 3.350882] usb 2-1: link qh256-0001/ffff880230cb5740 start 1 [1/0 us] [ 3.417104] usb 1-1.4: skipped 1 descriptor after interface [ 3.417376] usb 1-1.4: default language 0x0409 [ 3.418637] usb 1-1.4: udev 3, busnum 1, minor = 2 [ 3.418641] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=217f [ 3.418643] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.418646] usb 1-1.4: Product: Broadcom Bluetooth Device [ 3.418648] usb 1-1.4: Manufacturer: Broadcom Corp [ 3.418650] usb 1-1.4: SerialNumber: 78DD08AFCD78 [ 3.418822] usb 1-1.4: usb_probe_device [ 3.418826] usb 1-1.4: configuration #1 chosen from 1 choice [ 3.419002] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0) [ 3.419096] usb 1-1.4: adding 1-1.4:1.1 (config #1, interface 1) [ 3.419165] usb 1-1.4: adding 1-1.4:1.2 (config #1, interface 2) [ 3.419226] usb 1-1.4: adding 1-1.4:1.3 (config #1, interface 3) [ 3.419489] hub 1-1:1.0: port 5, status 0101, change 0000, 12 Mb/s [ 3.489858] usb 1-1.5: new high-speed USB device number 4 using ehci-pci [ 3.501247] Bluetooth: Core ver 2.16 [ 3.501270] NET: Registered protocol family 31 [ 3.501271] Bluetooth: HCI device and connection manager initialized [ 3.501280] Bluetooth: HCI socket layer initialized [ 3.501283] Bluetooth: L2CAP socket layer initialized [ 3.501290] Bluetooth: SCO socket layer initialized [ 3.504604] btusb 1-1.4:1.0: usb_probe_interface [ 3.504608] btusb 1-1.4:1.0: usb_probe_interface - got id [ 3.504841] btusb 1-1.4:1.2: usb_probe_interface [ 3.504843] btusb 1-1.4:1.2: usb_probe_interface - got id [ 3.504858] btusb 1-1.4:1.3: usb_probe_interface [ 3.504861] btusb 1-1.4:1.3: usb_probe_interface - got id [ 3.504890] usbcore: registered new interface driver btusb [ 3.505086] usb 1-1.4: link qh1-0e01/ffff880230cb97c0 start 0 [1/2 us] [ 3.559229] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd047b3/0xb40000/0xa0000, board id: 71, fw id: 615624 [ 3.559240] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0 [ 3.583766] usb 1-1.5: udev 4, busnum 1, minor = 3 [ 3.583770] usb 1-1.5: New USB device found, idVendor=17ef, idProduct=1005 [ 3.583772] usb 1-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.583968] usb 1-1.5: usb_probe_device [ 3.583973] usb 1-1.5: configuration #1 chosen from 1 choice [ 3.584148] usb 1-1.5: adding 1-1.5:1.0 (config #1, interface 0) [ 3.584195] hub 1-1.5:1.0: usb_probe_interface [ 3.584198] hub 1-1.5:1.0: usb_probe_interface - got id [ 3.584203] hub 1-1.5:1.0: USB hub found [ 3.584374] hub 1-1.5:1.0: 4 ports detected [ 3.584378] hub 1-1.5:1.0: standalone hub [ 3.584381] hub 1-1.5:1.0: individual port power switching [ 3.584383] hub 1-1.5:1.0: individual port over-current protection [ 3.584524] hub 1-1.5:1.0: TT per port [ 3.584529] hub 1-1.5:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.584531] hub 1-1.5:1.0: power on to power good time: 100ms [ 3.584752] hub 1-1.5:1.0: local power source is good [ 3.584840] hub 1-1.5:1.0: enabling power on all ports [ 3.585524] hub 1-1:1.0: port 6, status 0101, change 0000, 12 Mb/s [ 3.613533] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 [ 3.654011] usb 1-1.6: new high-speed USB device number 5 using ehci-pci [ 3.659924] Console: switching to colour frame buffer device 160x50 [ 3.662502] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device [ 3.662503] i915 0000:00:02.0: registered panic notifier [ 3.663852] acpi device:01: registered as cooling_device4 [ 3.663904] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [ 3.663950] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7 [ 3.664116] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 3.664261] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X [ 3.675847] hda_codec: CX20585: BIOS auto-probing. [ 3.677490] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8 [ 3.681991] hub 1-1.5:1.0: port 2: status 0101 change 0001 [ 3.682237] hub 1-1.5:1.0: port 3: status 0101 change 0001 [ 3.684301] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 3.684455] input: HDA Intel MID Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 3.684550] input: HDA Intel MID Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 3.684642] input: HDA Intel MID Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 3.684741] input: HDA Intel MID Dock Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 3.751199] usb 1-1.6: skipped 1 descriptor after configuration [ 3.751207] usb 1-1.6: skipped 5 descriptors after interface [ 3.751211] usb 1-1.6: skipped 1 descriptor after endpoint [ 3.751215] usb 1-1.6: skipped 19 descriptors after interface [ 3.751540] usb 1-1.6: default language 0x0409 [ 3.752781] usb 1-1.6: udev 5, busnum 1, minor = 4 [ 3.752787] usb 1-1.6: New USB device found, idVendor=17ef, idProduct=4816 [ 3.752791] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.752795] usb 1-1.6: Product: Integrated Camera [ 3.752798] usb 1-1.6: Manufacturer: Chicony Electronics Co., Ltd. [ 3.752941] usb 1-1.6: usb_probe_device [ 3.752948] usb 1-1.6: configuration #1 chosen from 1 choice [ 3.753145] usb 1-1.6: adding 1-1.6:1.0 (config #1, interface 0) [ 3.753757] usb 1-1.6: adding 1-1.6:1.1 (config #1, interface 1) [ 3.753862] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0010 [ 3.754002] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000 [ 3.754020] hub 2-1:1.0: hub_suspend [ 3.754033] usb 2-1: unlink qh256-0001/ffff880230cb5740 start 1 [1/0 us] [ 3.755632] usb 2-1: usb auto-suspend, wakeup 1 [ 3.769838] hub 2-0:1.0: hub_suspend [ 3.769856] usb usb2: bus auto-suspend, wakeup 1 [ 3.769863] ehci-pci 0000:00:1d.0: suspend root hub [ 3.781826] usb 1-1.5: link qh256-0001/ffff880232286640 start 3 [1/0 us] [ 3.781849] hub 1-1.5:1.0: state 7 ports 4 chg 000c evt 0000 [ 3.782006] hub 1-1.5:1.0: port 2, status 0101, change 0000, 12 Mb/s [ 3.785944] ehci-pci 0000:00:1d.0: hcd_pci_runtime_suspend: 0 [ 3.801829] ehci-pci 0000:00:1d.0: power state changed by ACPI to D3cold [ 3.801868] ehci-pci 0000:00:1d.0: power state changed by ACPI to D0 [ 3.854065] usb 1-1.5.2: new full-speed USB device number 6 using ehci-pci [ 3.906058] ehci-pci 0000:00:1d.0: setting latency timer to 64 [ 3.906078] ehci-pci 0000:00:1d.0: hcd_pci_runtime_resume: 0 [ 3.906087] usb usb2: usb auto-resume [ 3.906091] ehci-pci 0000:00:1d.0: resume root hub [ 3.906112] hub 2-0:1.0: hub_resume [ 3.906121] hub 2-0:1.0: port 1: status 0507 change 0000 [ 3.906138] usb 2-1: usb auto-resume [ 3.937882] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 3.949430] usb 1-1.5.2: skipped 1 descriptor after interface [ 3.949836] usb 1-1.5.2: default language 0x0409 [ 3.951297] usb 1-1.5.2: udev 6, busnum 1, minor = 5 [ 3.951303] usb 1-1.5.2: New USB device found, idVendor=056a, idProduct=0065 [ 3.951307] usb 1-1.5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.951310] usb 1-1.5.2: Product: MTE-450 [ 3.951314] usb 1-1.5.2: Manufacturer: Wacom Co.,Ltd. [ 3.951485] usb 1-1.5.2: usb_probe_device [ 3.951491] usb 1-1.5.2: configuration #1 chosen from 1 choice [ 3.951792] usb 1-1.5.2: adding 1-1.5.2:1.0 (config #1, interface 0) [ 3.952042] hub 1-1.5:1.0: port 3, status 0101, change 0000, 12 Mb/s [ 3.953855] usb 2-1: finish resume [ 3.954163] hub 2-1:1.0: hub_resume [ 3.955169] ehci-pci 0000:00:1d.0: reused qh ffff880230cb5740 schedule [ 3.955177] usb 2-1: link qh256-0001/ffff880230cb5740 start 1 [1/0 us] [ 3.965908] hub 1-1.5:1.0: port 3 not reset yet, waiting 10ms [ 3.977699] wacom 1-1.5.2:1.0: usb_probe_interface [ 3.977709] wacom 1-1.5.2:1.0: usb_probe_interface - got id [ 3.977894] input: Wacom Bamboo as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.2/1-1.5.2:1.0/input/input14 [ 3.978696] usbcore: registered new interface driver wacom [ 3.982490] hidraw: raw HID events driver (C) Jiri Kosina [ 3.985075] usbcore: registered new interface driver usbhid [ 3.985079] usbhid: USB HID core driver [ 4.038084] usb 1-1.5.3: new high-speed USB device number 7 using ehci-pci [ 4.130442] usb 1-1.5.3: udev 7, busnum 1, minor = 6 [ 4.130449] usb 1-1.5.3: New USB device found, idVendor=050d, idProduct=0237 [ 4.130453] usb 1-1.5.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 4.130655] usb 1-1.5.3: usb_probe_device [ 4.130661] usb 1-1.5.3: configuration #1 chosen from 1 choice [ 4.130820] usb 1-1.5.3: adding 1-1.5.3:1.0 (config #1, interface 0) [ 4.130874] hub 1-1.5.3:1.0: usb_probe_interface [ 4.130879] hub 1-1.5.3:1.0: usb_probe_interface - got id [ 4.130885] hub 1-1.5.3:1.0: USB hub found [ 4.131045] hub 1-1.5.3:1.0: 7 ports detected [ 4.131050] hub 1-1.5.3:1.0: standalone hub [ 4.131052] hub 1-1.5.3:1.0: ganged power switching [ 4.131055] hub 1-1.5.3:1.0: global over-current protection [ 4.131213] hub 1-1.5.3:1.0: TT per port [ 4.131221] hub 1-1.5.3:1.0: TT requires at most 8 FS bit times (666 ns) [ 4.131226] hub 1-1.5.3:1.0: power on to power good time: 100ms [ 4.131426] hub 1-1.5.3:1.0: local power source is good [ 4.131430] hub 1-1.5.3:1.0: no over-current condition exists [ 4.131542] hub 1-1.5.3:1.0: enabling power on all ports [ 4.132466] hub 1-1.5:1.0: state 7 ports 4 chg 0000 evt 0008 [ 4.132559] hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 [ 4.132567] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000 [ 4.230617] hub 1-1.5.3:1.0: port 3: status 0301 change 0001 [ 4.230872] hub 1-1.5.3:1.0: port 4: status 0301 change 0001 [ 4.231218] hub 1-1.5.3:1.0: port 6: status 0101 change 0001 [ 4.231464] hub 1-1.5.3:1.0: port 7: status 0101 change 0001 [ 4.329977] usb 1-1.5.3: link qh256-0001/ffff88022dd7ccc0 start 4 [1/0 us] [ 4.329998] hub 1-1.5.3:1.0: state 7 ports 7 chg 00d8 evt 0000 [ 4.330117] hub 1-1.5.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s [ 4.402117] usb 1-1.5.3.3: new low-speed USB device number 8 using ehci-pci [ 4.418150] hub 1-1.5.3:1.0: port 3 not reset yet, waiting 10ms [ 4.513651] usb 1-1.5.3.3: skipped 1 descriptor after interface [ 4.513658] usb 1-1.5.3.3: skipped 1 descriptor after interface [ 4.514155] usb 1-1.5.3.3: default language 0x0409 [ 4.516155] usb 1-1.5.3.3: udev 8, busnum 1, minor = 7 [ 4.516162] usb 1-1.5.3.3: New USB device found, idVendor=046d, idProduct=c505 [ 4.516166] usb 1-1.5.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.516170] usb 1-1.5.3.3: Product: USB Receiver [ 4.516173] usb 1-1.5.3.3: Manufacturer: Logitech [ 4.516329] usb 1-1.5.3.3: usb_probe_device [ 4.516335] usb 1-1.5.3.3: configuration #1 chosen from 1 choice [ 4.516746] usb 1-1.5.3.3: adding 1-1.5.3.3:1.0 (config #1, interface 0) [ 4.516820] usbhid 1-1.5.3.3:1.0: usb_probe_interface [ 4.516827] usbhid 1-1.5.3.3:1.0: usb_probe_interface - got id [ 4.519334] usb 1-1.5.3.3: adding 1-1.5.3.3:1.1 (config #1, interface 1) [ 4.519378] usbhid 1-1.5.3.3:1.1: usb_probe_interface [ 4.519382] usbhid 1-1.5.3.3:1.1: usb_probe_interface - got id [ 4.525454] hub 1-1.5.3:1.0: port 4, status 0301, change 0000, 1.5 Mb/s [ 4.537966] hub 1-1.5.3:1.0: port 4 not reset yet, waiting 10ms [ 4.554157] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.3/1-1.5.3.3/1-1.5.3.3:1.0/input/input15 [ 4.554210] usb 1-1.5.3.3: link qh8-0e01/ffff88022dd7cb40 start 5 [1/2 us] [ 4.554348] hid-generic 0003:046D:C505.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1a.0-1.5.3.3/input0 [ 4.554889] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.3/1-1.5.3.3/1-1.5.3.3:1.1/input/input16 [ 4.554937] usb 1-1.5.3.3: link qh8-0e01/ffff88022dd7ca40 start 6 [1/2 us] [ 4.555145] hid-generic 0003:046D:C505.0002: input,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1a.0-1.5.3.3/input1 [ 4.610175] usb 1-1.5.3.4: new low-speed USB device number 9 using ehci-pci [ 4.626128] hub 1-1.5.3:1.0: port 4 not reset yet, waiting 10ms [ 4.720926] usb 1-1.5.3.4: skipped 1 descriptor after interface [ 4.721291] usb 1-1.5.3.4: default language 0x0409 [ 4.723550] usb 1-1.5.3.4: udev 9, busnum 1, minor = 8 [ 4.723557] usb 1-1.5.3.4: New USB device found, idVendor=046d, idProduct=c01d [ 4.723561] usb 1-1.5.3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.723565] usb 1-1.5.3.4: Product: USB-PS/2 Optical Mouse [ 4.723568] usb 1-1.5.3.4: Manufacturer: Logitech [ 4.723720] usb 1-1.5.3.4: usb_probe_device [ 4.723728] usb 1-1.5.3.4: configuration #1 chosen from 1 choice [ 4.724178] usb 1-1.5.3.4: adding 1-1.5.3.4:1.0 (config #1, interface 0) [ 4.724237] usbhid 1-1.5.3.4:1.0: usb_probe_interface [ 4.724243] usbhid 1-1.5.3.4:1.0: usb_probe_interface - got id [ 4.727426] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.3/1-1.5.3.4/1-1.5.3.4:1.0/input/input17 [ 4.727608] hid-generic 0003:046D:C01D.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.0-1.5.3.4/input0 [ 4.727725] hub 1-1.5.3:1.0: port 6, status 0101, change 0000, 12 Mb/s [ 4.741976] hub 1-1.5.3:1.0: port 6 not reset yet, waiting 10ms [ 4.814170] usb 1-1.5.3.6: new full-speed USB device number 10 using ehci-pci [ 4.907191] usb 1-1.5.3.6: default language 0x0409 [ 4.908272] usb 1-1.5.3.6: udev 10, busnum 1, minor = 9 [ 4.908278] usb 1-1.5.3.6: New USB device found, idVendor=10c4, idProduct=ea60 [ 4.908282] usb 1-1.5.3.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.908286] usb 1-1.5.3.6: Product: CP2102 USB to UART Bridge Controller [ 4.908290] usb 1-1.5.3.6: Manufacturer: Silicon Labs [ 4.908293] usb 1-1.5.3.6: SerialNumber: 0138 [ 4.908492] usb 1-1.5.3.6: usb_probe_device [ 4.908498] usb 1-1.5.3.6: configuration #1 chosen from 1 choice [ 4.908765] usb 1-1.5.3.6: adding 1-1.5.3.6:1.0 (config #1, interface 0) [ 4.909507] hub 1-1.5.3:1.0: port 7, status 0101, change 0000, 12 Mb/s [ 4.921997] hub 1-1.5.3:1.0: port 7 not reset yet, waiting 10ms [ 4.937611] usbcore: registered new interface driver usbserial [ 4.937634] usbcore: registered new interface driver usbserial_generic [ 4.937648] usbserial: USB Serial support registered for generic [ 4.938799] usbcore: registered new interface driver cp210x [ 4.938826] usbserial: USB Serial support registered for cp210x [ 4.938903] cp210x 1-1.5.3.6:1.0: usb_probe_interface [ 4.938913] cp210x 1-1.5.3.6:1.0: usb_probe_interface - got id [ 4.938925] cp210x 1-1.5.3.6:1.0: cp210x converter detected [ 4.994139] usb 1-1.5.3.7: new full-speed USB device number 11 using ehci-pci [ 5.086949] usb 1-1.5.3.7: skipped 16 descriptors after interface [ 5.086956] usb 1-1.5.3.7: skipped 2 descriptors after interface [ 5.086960] usb 1-1.5.3.7: skipped 1 descriptor after endpoint [ 5.086964] usb 1-1.5.3.7: skipped 2 descriptors after interface [ 5.086967] usb 1-1.5.3.7: skipped 1 descriptor after endpoint [ 5.086971] usb 1-1.5.3.7: skipped 2 descriptors after interface [ 5.086974] usb 1-1.5.3.7: skipped 1 descriptor after endpoint [ 5.086977] usb 1-1.5.3.7: skipped 1 descriptor after interface [ 5.087184] usb 1-1.5.3.7: default language 0x0409 [ 5.087474] usb 1-1.5.3.7: udev 11, busnum 1, minor = 10 [ 5.087481] usb 1-1.5.3.7: New USB device found, idVendor=0ccd, idProduct=0028 [ 5.087485] usb 1-1.5.3.7: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 5.087489] usb 1-1.5.3.7: Product: USB Audio [ 5.087688] usb 1-1.5.3.7: usb_probe_device [ 5.087695] usb 1-1.5.3.7: configuration #1 chosen from 1 choice [ 5.087925] usb 1-1.5.3.7: adding 1-1.5.3.7:1.0 (config #1, interface 0) [ 5.088001] usb 1-1.5.3.7: adding 1-1.5.3.7:1.1 (config #1, interface 1) [ 5.088056] usb 1-1.5.3.7: adding 1-1.5.3.7:1.2 (config #1, interface 2) [ 5.088117] usb 1-1.5.3.7: adding 1-1.5.3.7:1.3 (config #1, interface 3) [ 5.088174] usbhid 1-1.5.3.7:1.3: usb_probe_interface [ 5.088180] usbhid 1-1.5.3.7:1.3: usb_probe_interface - got id [ 5.089103] input: USB Audio as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5.3/1-1.5.3.7/1-1.5.3.7:1.3/input/input18 [ 5.089129] usb 1-1.5.3.7: link qh32-0e01/ffff880230e368c0 start 7 [1/2 us] [ 5.089268] hid-generic 0003:0CCD:0028.0004: input,hidraw3: USB HID v1.00 Device [USB Audio] on usb-0000:00:1a.0-1.5.3.7/input3 [ 5.089332] hub 1-1.5.3:1.0: state 7 ports 7 chg 0000 evt 0040 [ 5.110014] hub 1-1.5.3:1.0: state 7 ports 7 chg 0000 evt 0040 [ 5.120623] snd-usb-audio 1-1.5.3.7:1.0: usb_probe_interface [ 5.120640] snd-usb-audio 1-1.5.3.7:1.0: usb_probe_interface - got id [ 5.122268] usbcore: registered new interface driver snd-usb-audio [ 5.158029] usb 1-1.5.3.6: reset full-speed USB device number 10 using ehci-pci [ 5.251394] usb 1-1.5.3.6: cp210x converter now attached to ttyUSB0 [ 5.550105] usb 1-1.4: unlink qh1-0e01/ffff880230cb97c0 start 0 [1/2 us] [ 5.552834] usb 1-1: clear tt buffer port 4, a3 ep2 t04048d82 [ 5.957233] EXT4-fs (dm-0): re-mounted. Opts: (null) [ 5.994134] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,discard [ 6.022887] loop: module loaded [ 6.429993] Adding 7811064k swap on /dev/mapper/Grubby-swap. Priority:-1 extents:1 across:7811064k SS [ 6.562005] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: discard [ 6.565105] EXT4-fs (dm-3): warning: maximal mount count reached, running e2fsck is recommended [ 6.565245] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: discard [ 6.577943] kjournald starting. Commit interval 5 seconds [ 6.577980] EXT3-fs (dm-4): warning: maximal mount count reached, running e2fsck is recommended [ 6.578094] EXT3-fs (dm-4): using internal journal [ 6.578101] EXT3-fs (dm-4): mounted filesystem with ordered data mode [ 6.901354] fuse init (API version 7.21) [ 6.995040] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 7.098236] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 7.098379] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.559903] psmouse serio2: alps: Unknown ALPS touchpad: E7=10 00 64, EC=10 00 64 [ 7.778344] intel ips 0000:00:1f.6: i915 driver attached, reenabling gpu turbo [ 7.939304] NET: Registered protocol family 15 [ 7.941504] alg: No test for cipher_null (cipher_null-generic) [ 7.941555] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 7.941605] alg: No test for compress_null (compress_null-generic) [ 7.941651] alg: No test for digest_null (digest_null-generic) [ 8.273591] usb 1-1.5.2: link qh4-0e01/ffff88022b96d3c0 start 0 [1/2 us] [ 8.286291] usb 1-1.5.2: unlink qh4-0e01/ffff88022b96d3c0 start 0 [1/2 us] [ 8.310436] usb 1-1.5.3.4: link qh8-0e01/ffff88022b96d2c0 start 1 [1/2 us] [ 8.330370] usb 1-1.5.3.4: unlink qh8-0e01/ffff88022b96d2c0 start 1 [1/2 us] [ 9.176718] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input19 [ 10.210505] e1000e 0000:00:19.0: setting latency timer to 64 [ 10.210563] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 10.213334] e1000e 0000:00:19.0 eth0: PHY Wakeup cause - Link Status Change [ 10.682454] Bluetooth: RFCOMM TTY layer initialized [ 10.682469] Bluetooth: RFCOMM socket layer initialized [ 10.682470] Bluetooth: RFCOMM ver 1.11 [ 10.686882] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 10.686885] Bluetooth: BNEP filters: protocol multicast [ 10.686897] Bluetooth: BNEP socket layer initialized [ 10.689108] ehci-pci 0000:00:1a.0: reused qh ffff880230cb97c0 schedule [ 10.689116] usb 1-1.4: link qh1-0e01/ffff880230cb97c0 start 0 [1/2 us] [ 10.974553] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S [ 10.981645] iwlwifi 0000:02:00.0: Radio type=0x0-0x3-0x1 [ 11.320268] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S [ 11.327359] iwlwifi 0000:02:00.0: Radio type=0x0-0x3-0x1 [ 11.539965] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.845300] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3 [ 12.138229] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input20 [ 12.677294] ehci-pci 0000:00:1a.0: reused qh ffff88022b96d3c0 schedule [ 12.677304] usb 1-1.5.2: link qh4-0e01/ffff88022b96d3c0 start 0 [1/2 us] [ 12.686697] usb 1-1.5.2: unlink qh4-0e01/ffff88022b96d3c0 start 0 [1/2 us] [ 12.695669] ehci-pci 0000:00:1a.0: reused qh ffff88022b96d3c0 schedule [ 12.695678] usb 1-1.5.2: link qh4-0e01/ffff88022b96d3c0 start 0 [1/2 us] [ 12.701797] ehci-pci 0000:00:1a.0: reused qh ffff88022b96d2c0 schedule [ 12.701806] usb 1-1.5.3.4: link qh8-0e01/ffff88022b96d2c0 start 1 [1/2 us] [ 13.617110] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx [ 13.617121] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO [ 13.617176] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 44.746262] sock: process `skype' is using obsolete setsockopt SO_BSDCOMPAT [ 50.226534] usb 1-1.5.3.4: unlink qh8-0e01/ffff88022b96d2c0 start 1 [1/2 us] [ 50.281844] usb 1-1.5.2: unlink qh4-0e01/ffff88022b96d3c0 start 0 [1/2 us] [ 51.670071] PM: Marking nosave pages: [mem 0x0009e000-0x000fffff] [ 51.670077] PM: Marking nosave pages: [mem 0xbb27c000-0xbb281fff] [ 51.670078] PM: Marking nosave pages: [mem 0xbb35f000-0xbb40efff] [ 51.670081] PM: Marking nosave pages: [mem 0xbb46f000-0xbb70efff] [ 51.670089] PM: Marking nosave pages: [mem 0xbb717000-0xbb71efff] [ 51.670090] PM: Marking nosave pages: [mem 0xbb76b000-0xbb7fefff] [ 51.670093] PM: Marking nosave pages: [mem 0xbb800000-0xffffffff] [ 51.670951] PM: Marking nosave pages: [mem 0x1fc000000-0x1ffffffff] [ 51.671161] PM: Basic memory bitmaps created [ 51.728065] Syncing filesystems ... done. [ 51.755222] Freezing user space processes ... (elapsed 0.01 seconds) done. [ 51.770099] PM: Preallocating image memory... [ 51.847119] delay: estimated 384, actual 0 [ 51.848339] delay: estimated 336, actual 0 [ 51.954475] done (allocated 518373 pages) [ 51.954481] PM: Allocated 2073492 kbytes in 0.18 seconds (11519.40 MB/s) [ 51.954482] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done. [ 52.002206] Suspending console(s) (use no_console_suspend to debug) [ 52.002267] usb 1-1.5.3.7: unlink qh32-0e01/ffff880230e368c0 start 7 [1/2 us] [ 52.002284] usb 1-1.5.3.3: unlink qh8-0e01/ffff88022dd7ca40 start 6 [1/2 us] [ 52.002344] hub 2-1:1.0: hub_suspend [ 52.002347] usb 1-1.4: unlink qh1-0e01/ffff880230cb97c0 start 0 [1/2 us] [ 52.002349] usb 2-1: unlink qh256-0001/ffff880230cb5740 start 1 [1/0 us] [ 52.004444] ehci-pci 0000:00:1a.0: shutdown urb ffff880231affa00 ep1out-iso [ 52.004447] ehci-pci 0000:00:1a.0: shutdown urb ffff88023145cc00 ep1out-iso [ 52.004450] ehci-pci 0000:00:1a.0: shutdown urb ffff88023145c800 ep1out-iso [ 52.004502] hub 2-0:1.0: hub_suspend [ 52.004518] usb usb2: bus suspend, wakeup 0 [ 52.004522] ehci-pci 0000:00:1d.0: suspend root hub [ 52.006009] usb 1-1.5.3.3: unlink qh8-0e01/ffff88022dd7cb40 start 5 [1/2 us] [ 52.006476] usb 1-1: clear tt buffer port 4, a3 ep2 t04048d80 [ 52.024481] hub 1-1.5.3:1.0: hub_suspend [ 52.024490] usb 1-1.5.3: unlink qh256-0001/ffff88022dd7ccc0 start 4 [1/0 us] [ 52.026689] hub 1-1.5:1.0: hub_suspend [ 52.026698] usb 1-1.5: unlink qh256-0001/ffff880232286640 start 3 [1/0 us] [ 52.028929] hub 1-1:1.0: hub_suspend [ 52.028937] usb 1-1: unlink qh256-0001/ffff880230cb5940 start 1 [1/0 us] [ 52.031217] hub 1-0:1.0: hub_suspend [ 52.031224] usb usb1: bus suspend, wakeup 0 [ 52.031227] ehci-pci 0000:00:1a.0: suspend root hub [ 52.572711] PM: freeze of devices complete after 570.449 msecs [ 52.572877] PM: late freeze of devices complete after 0.164 msecs [ 52.573527] PM: noirq freeze of devices complete after 0.648 msecs [ 52.573859] ACPI: Preparing to enter system sleep state S4 [ 52.578117] PM: Saving platform NVS memory [ 52.579293] Disabling non-boot CPUs ... [ 52.681989] smpboot: CPU 1 is now offline [ 52.683708] smpboot: CPU 2 is now offline [ 52.685347] smpboot: CPU 3 is now offline [ 52.685980] PM: Creating hibernation image: [ 52.778205] PM: Need to copy 517055 pages [ 52.778206] PM: Normal pages needed: 517055 + 1024, available pages: 1527629 [ 53.539910] PM: Hibernation image created (517055 pages copied) [ 52.686982] Enabling non-boot CPUs ... [ 52.687111] smpboot: Booting Node 0 Processor 1 APIC 0x1 [ 52.700603] CPU1 is up [ 52.700666] smpboot: Booting Node 0 Processor 2 APIC 0x4 [ 52.713984] CPU2 is up [ 52.714064] smpboot: Booting Node 0 Processor 3 APIC 0x5 [ 52.727464] CPU3 is up [ 52.729547] ACPI: Waking up from system sleep state S4 [ 52.759671] PM: noirq thaw of devices complete after 0.262 msecs [ 52.759823] PM: early thaw of devices complete after 0.127 msecs [ 52.759860] e1000e 0000:00:19.0: setting latency timer to 64 [ 52.759917] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 52.759929] pci 0000:00:1e.0: setting latency timer to 64 [ 52.760024] ahci 0000:00:1f.2: setting latency timer to 64 [ 52.763363] usb usb1: usb resume [ 52.763367] ehci-pci 0000:00:1a.0: resume root hub [ 52.763492] usb usb2: usb resume [ 52.763496] ehci-pci 0000:00:1d.0: resume root hub [ 52.775184] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X [ 52.798173] hub 2-0:1.0: hub_resume [ 52.798175] hub 1-0:1.0: hub_resume [ 52.798186] hub 1-0:1.0: port 1: status 0503 change 0000 [ 52.798189] hub 2-0:1.0: port 1: status 0503 change 0000 [ 52.798212] hub 1-1:1.0: hub_resume [ 52.798214] hub 2-1:1.0: hub_resume [ 52.798692] hub 1-1:1.0: port 4: status 0103 change 0000 [ 52.798819] hub 1-1:1.0: port 5: status 0100 change 0001 [ 52.799042] hub 1-1:1.0: port 6: status 0503 change 0000 [ 52.799212] ehci-pci 0000:00:1d.0: reused qh ffff880230cb5740 schedule [ 52.799217] usb 2-1: link qh256-0001/ffff880230cb5740 start 1 [1/0 us] [ 52.811146] tpm_tis 00:09: TPM is disabled/deactivated (0x6) [ 52.899136] ehci-pci 0000:00:1a.0: reused qh ffff880230cb5940 schedule [ 52.899142] usb 1-1: link qh256-0001/ffff880230cb5940 start 1 [1/0 us] [ 52.899288] ehci-pci 0000:00:1a.0: reused qh ffff880230cb97c0 schedule [ 52.899290] usb 1-1.4: link qh1-0e01/ffff880230cb97c0 start 0 [1/2 us] [ 52.899345] hub 1-1:1.0: port 5 status 0000.0100 after resume, -19 [ 52.899347] usb 1-1.5: can't resume, status -19 [ 52.899348] hub 1-1:1.0: logical disconnect on port 5 [ 53.083171] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 53.085867] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded [ 53.086584] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded [ 53.091460] ata5: SATA link down (SStatus 0 SControl 300) [ 53.091798] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded [ 53.092562] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded [ 53.094144] ata2.00: configured for UDMA/100 [ 53.099163] ata6: SATA link down (SStatus 0 SControl 300) [ 53.107180] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 53.107693] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded [ 53.107697] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out [ 53.107699] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out [ 53.108538] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded [ 53.108541] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out [ 53.108543] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out [ 53.108835] ata1.00: configured for UDMA/133 [ 53.124492] PM: thaw of devices complete after 364.635 msecs [ 56.399968] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000 [ 56.399978] hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 [ 56.399983] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0000 [ 56.399988] hub 1-1:1.0: state 7 ports 6 chg 0020 evt 0000 [ 56.399885] Restarting kernel threads ... done. [ 56.401279] hub 1-1:1.0: port 5, status 0100, change 0000, 12 Mb/s [ 56.401977] usb 1-1.5: USB disconnect, device number 4 [ 56.401982] usb 1-1.5.2: USB disconnect, device number 6 [ 56.401984] usb 1-1.5.2: unregistering device [ 56.401987] usb 1-1.5.2: unregistering interface 1-1.5.2:1.0 [ 56.400083] Restarting tasks ... done. [ 56.461891] PM: Basic memory bitmaps freed [ 56.469470] video LNXVIDEO:00: Restoring backlight state [ 56.495569] usb 1-1.5.2: usb_disable_device nuking all URBs [ 56.495689] usb 1-1.5.3: USB disconnect, device number 7 [ 56.495695] usb 1-1.5.3.3: USB disconnect, device number 8 [ 56.495697] usb 1-1.5.3.3: unregistering device [ 56.495700] usb 1-1.5.3.3: unregistering interface 1-1.5.3.3:1.0 [ 56.531858] usb 1-1.5.3.3: unregistering interface 1-1.5.3.3:1.1 [ 56.559624] usb 1-1.5.3.3: usb_disable_device nuking all URBs [ 56.567599] usb 1-1.5.3.4: USB disconnect, device number 9 [ 56.567604] usb 1-1.5.3.4: unregistering device [ 56.567607] usb 1-1.5.3.4: unregistering interface 1-1.5.3.4:1.0 [ 56.579803] usb 1-1.5.3.4: usb_disable_device nuking all URBs [ 56.580210] usb 1-1.5.3.6: USB disconnect, device number 10 [ 56.580214] usb 1-1.5.3.6: unregistering device [ 56.580217] usb 1-1.5.3.6: unregistering interface 1-1.5.3.6:1.0 [ 56.580327] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [ 56.580343] cp210x 1-1.5.3.6:1.0: device disconnected [ 56.580360] usb 1-1.5.3.6: usb_disable_device nuking all URBs [ 56.580444] usb 1-1.5.3.7: USB disconnect, device number 11 [ 56.580447] usb 1-1.5.3.7: unregistering device [ 56.580450] usb 1-1.5.3.7: unregistering interface 1-1.5.3.7:1.0 [ 56.582492] usb 1-1.5.3.7: unregistering interface 1-1.5.3.7:1.1 [ 56.582554] usb 1-1.5.3.7: unregistering interface 1-1.5.3.7:1.2 [ 56.582586] usb 1-1.5.3.7: unregistering interface 1-1.5.3.7:1.3 [ 56.607671] usb 1-1.5.3.7: usb_disable_device nuking all URBs [ 56.607781] usb 1-1.5.3: unregistering device [ 56.607784] usb 1-1.5.3: unregistering interface 1-1.5.3:1.0 [ 56.607910] usb 1-1.5.3: usb_disable_device nuking all URBs [ 56.607993] usb 1-1.5: unregistering device [ 56.607997] usb 1-1.5: unregistering interface 1-1.5:1.0 [ 56.608084] usb 1-1.5: usb_disable_device nuking all URBs [ 57.799842] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 57.903606] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X [ 57.903758] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 57.904985] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S [ 57.912046] iwlwifi 0000:02:00.0: Radio type=0x0-0x3-0x1 [ 58.175000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 59.454040] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx [ 59.454052] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO [ 59.454105] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
