Model RESET and Power for HS USB Port 1 as GPIO fixed regulators
and link them to the 'nop-usb-xceiv' PHY by making them as "reset"
and "vcc" supplies.
The RESET and Power will then be managed by the PHY driver.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
Acked-by: Felipe Balbi <balbi@xxxxxx>
---
arch/arm/mach-omap2/board-omap4panda.c | 92 +++++++++++++++++++++++---------
1 files changed, 66 insertions(+), 26 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index feffde6..3f34db3 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -147,6 +147,70 @@ static struct platform_device hsusb1_phy_device = {
},
};
+/* Regulator for USB HUB/PHY reset */
+static struct regulator_consumer_supply hsusb1_reset_supplies[] = {
+/* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb1_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb1_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_reset_config = {
+ .supply_name = "hsusb1_reset",
+ .microvolts = 3300000,
+ .gpio = GPIO_HUB_NRESET,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hsusb1_reset_data,
+};
+
+static struct platform_device hsusb1_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb1_reset_config,
+ },
+};
+
+/* Regulator for USB HUB supply */
+static struct regulator_consumer_supply hsusb1_power_supplies[] = {
+/* Link PHY device to USB HUB supply so it gets enabled in the PHY driver */
+ REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_power_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb1_power_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb1_power_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_power_config = {
+ .supply_name = "hsusb1_vbus",
+ .microvolts = 3300000,
+ .gpio = GPIO_HUB_POWER,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+ .init_data = &hsusb1_power_data,
+};
+
+static struct platform_device hsusb1_power_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb1_power_config,
+ },
+};
+
static struct platform_device *panda_devices[] __initdata = {
&leds_gpio,
&wl1271_device,
@@ -154,39 +218,18 @@ static struct platform_device *panda_devices[] __initdata = {
&panda_hdmi_audio_codec,
&btwilink_device,
&hsusb1_phy_device,
+ &hsusb1_power_device,
+ &hsusb1_reset_device,
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
- .phy_reset = false,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
-};
-
-static struct gpio panda_ehci_gpios[] __initdata = {
- { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" },
- { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
};
static void __init omap4_ehci_init(void)
{
int ret;
- /* disable the power to the usb hub prior to init and reset phy+hub */
- ret = gpio_request_array(panda_ehci_gpios,
- ARRAY_SIZE(panda_ehci_gpios));
- if (ret) {
- pr_err("Unable to initialize EHCI power/reset\n");
- return;
- }
-
- gpio_export(GPIO_HUB_POWER, 0);
- gpio_export(GPIO_HUB_NRESET, 0);
- gpio_set_value(GPIO_HUB_NRESET, 1);
-
/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
ret = clk_add_alias("main_clk", "nop_usb_xceiv.1", "auxclk3_ck", NULL);
if (ret)
@@ -196,9 +239,6 @@ static void __init omap4_ehci_init(void)
usb_bind_phy("ehci-omap.0", 0, "nop_usb_xceiv.1");
usbhs_init(&usbhs_bdata);
-
- /* enable power to hub */
- gpio_set_value(GPIO_HUB_POWER, 1);
}
static struct omap_musb_board_data musb_board_data = {
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
