> Looking at the different ethernet drivers, the normal way do do this
> seems to be something like this in their .set_wol implementation:
>
> device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
>
>
> where "adapter" is a netdev_priv private struct, "pdev" is a pci device
> and "wol" is an u32. I don't see any problem doing the same for USB
> network devices implementing ethtool "set_wol".
Ahh, good spot. I've implemented this (patch below for reference) and
it still doesn't work:
$ cat /sys/bus/usb/devices/2-1.2/power/wakeup
disabled
$ sudo ethtool -s eth2 wol p
[ 1607.237767] smsc75xx 2-1.2:1.0 eth2: set_wol before
device_can_wakeup=1 device_may_wakeup=0
[ 1607.237772] smsc75xx 2-1.2:1.0 eth2: set_wol after
device_can_wakeup=1 device_may_wakeup=1
$ cat /sys/bus/usb/devices/2-1.2/power/wakeup
disabled
Huh?! My debugging printk statements tell me I've succesfully set it,
but then the sysfs entry is disabled when I read it. Is something
else setting this back?
My testing patch for reference (note this is against my tree with a
few to-be submitted patches so won't apply cleanly!):
diff --git a/drivers/net/usb/smsc75xx.c b/drivers/net/usb/smsc75xx.c
index d8fa649..4c17849 100644
--- a/drivers/net/usb/smsc75xx.c
+++ b/drivers/net/usb/smsc75xx.c
@@ -61,7 +61,6 @@
#define SUSPEND_SUSPEND1 (0x02)
#define SUSPEND_SUSPEND2 (0x04)
#define SUSPEND_SUSPEND3 (0x08)
-#define SUSPEND_REMOTEWAKE (0x10)
#define SUSPEND_ALLMODES (SUSPEND_SUSPEND0 | SUSPEND_SUSPEND1 | \
SUSPEND_SUSPEND2 | SUSPEND_SUSPEND3)
@@ -172,26 +171,6 @@ static int __must_check smsc75xx_write_reg(struct
usbnet *dev, u32 index,
return __smsc75xx_write_reg(dev, index, data, 0);
}
-static int smsc75xx_set_feature(struct usbnet *dev, u32 feature)
-{
- if (WARN_ON_ONCE(!dev))
- return -EINVAL;
-
- return usbnet_write_cmd_nopm(dev, USB_REQ_SET_FEATURE,
- USB_DIR_OUT | USB_RECIP_DEVICE,
- feature, 0, NULL, 0);
-}
-
-static int smsc75xx_clear_feature(struct usbnet *dev, u32 feature)
-{
- if (WARN_ON_ONCE(!dev))
- return -EINVAL;
-
- return usbnet_write_cmd_nopm(dev, USB_REQ_CLEAR_FEATURE,
- USB_DIR_OUT | USB_RECIP_DEVICE,
- feature, 0, NULL, 0);
-}
-
/* Loop until the read is completed with timeout
* called with phy_mutex held */
static __must_check int __smsc75xx_phy_wait_not_busy(struct usbnet *dev,
@@ -674,8 +653,19 @@ static int smsc75xx_ethtool_set_wol(struct net_device *net,
{
struct usbnet *dev = netdev_priv(net);
struct smsc75xx_priv *pdata = (struct smsc75xx_priv *)(dev->data[0]);
+ int ret;
+
+ netdev_info(dev->net, "set_wol before device_can_wakeup=%d
device_may_wakeup=%d\n",
+ device_can_wakeup(&net->dev), device_may_wakeup(&net->dev));
pdata->wolopts = wolinfo->wolopts & SUPPORTED_WAKE;
+
+ ret = device_set_wakeup_enable(&net->dev, pdata->wolopts);
+ check_warn_return(ret, "device_set_wakeup_enable error %d\n", ret);
+
+ netdev_info(dev->net, "set_wol after device_can_wakeup=%d
device_may_wakeup=%d\n",
+ device_can_wakeup(&net->dev), device_may_wakeup(&net->dev));
+
return 0;
}
@@ -1197,12 +1187,17 @@ static int smsc75xx_bind(struct usbnet *dev,
struct usb_interface *intf)
/* Init all registers */
ret = smsc75xx_reset(dev);
+ check_warn_return(ret, "smsc75xx_reset error %d\n", ret);
dev->net->netdev_ops = &smsc75xx_netdev_ops;
dev->net->ethtool_ops = &smsc75xx_ethtool_ops;
dev->net->flags |= IFF_MULTICAST;
dev->net->hard_header_len += SMSC75XX_TX_OVERHEAD;
dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len;
+
+ ret = device_init_wakeup(&dev->net->dev, 1);
+ check_warn_return(ret, "device_init_wakeup error %d\n", ret);
+
return 0;
}
@@ -1262,9 +1257,7 @@ static int smsc75xx_enter_suspend0(struct usbnet *dev)
ret = smsc75xx_write_reg_nopm(dev, PMT_CTL, val);
check_warn_return(ret, "Error writing PMT_CTL\n");
- smsc75xx_set_feature(dev, USB_DEVICE_REMOTE_WAKEUP);
-
- pdata->suspend_flags |= SUSPEND_SUSPEND0 | SUSPEND_REMOTEWAKE;
+ pdata->suspend_flags |= SUSPEND_SUSPEND0;
return 0;
}
@@ -1291,9 +1284,7 @@ static int smsc75xx_enter_suspend1(struct usbnet *dev)
ret = smsc75xx_write_reg_nopm(dev, PMT_CTL, val);
check_warn_return(ret, "Error writing PMT_CTL\n");
- smsc75xx_set_feature(dev, USB_DEVICE_REMOTE_WAKEUP);
-
- pdata->suspend_flags |= SUSPEND_SUSPEND1 | SUSPEND_REMOTEWAKE;
+ pdata->suspend_flags |= SUSPEND_SUSPEND1;
return 0;
}
@@ -1348,9 +1339,7 @@ static int smsc75xx_enter_suspend3(struct usbnet *dev)
ret = smsc75xx_write_reg_nopm(dev, PMT_CTL, val);
check_warn_return(ret, "Error writing PMT_CTL\n");
- smsc75xx_set_feature(dev, USB_DEVICE_REMOTE_WAKEUP);
-
- pdata->suspend_flags |= SUSPEND_SUSPEND3 | SUSPEND_REMOTEWAKE;
+ pdata->suspend_flags |= SUSPEND_SUSPEND3;
return 0;
}
@@ -1650,11 +1639,6 @@ static int smsc75xx_resume(struct usb_interface *intf)
/* do this first to ensure it's cleared even in error case */
pdata->suspend_flags = 0;
- if (suspend_flags & SUSPEND_REMOTEWAKE) {
- ret = smsc75xx_clear_feature(dev, USB_DEVICE_REMOTE_WAKEUP);
- check_warn_return(ret, "Error disabling remote wakeup\n");
- }
-
if (suspend_flags & SUSPEND_ALLMODES) {
/* Disable wakeup sources */
ret = smsc75xx_read_reg_nopm(dev, WUCSR, &val);
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
