huang ying <huang.ying.caritas@xxxxxxxxx> writes: > Hi, Bjorn, > > Thank you very much for your detailed information. > > On Wed, Jul 25, 2012 at 5:58 PM, Bjørn Mork <bjorn@xxxxxxx> wrote: >> Huang Ying <ying.huang@xxxxxxxxx> writes: >>> On Wed, 2012-07-25 at 06:08 +0200, Bjørn Mork wrote: >>>> Enabling autosuspend for USB causes hotplug failure in the current >>>> linux-next. Newly plugged devices are not detected at all until the >>>> port/controller is manually powered on by writing "on" to power/control. >>>> Testing is pretty simple: >>>> >>>> 1) for f in /sys/bus/usb/devices/*/power/control; do echo auto > $f; done >>> >>> Have you done: >>> >>> for f in /sys/bus/pci/devices/*/power/confol; do echo auto > $f; done >>> >>> ? >>> >>> If not, the pci device will not be suspended at all. >> >> Yes, sorry for missing that. I had it automatically enabled. Yes, >> autosuspend for the PCI device and all child devices must be enabled for >> the device to be suspended at all, of course. >> >>>> 2) wait for the controllers to suspend >>>> 3) plugin a new USB device >>> >>> After plugin the new USB device, is there anything in dmesg? >> >> No. Absolutely nothing, so the USB devices is not enumerated. Another >> indication of the same: Plugging a device like an Android phone, which >> normally detects being connected to a host and presents a device type >> menu to the user, results in the charging LED lighting up but no menu. >> >> >> Trying to show the sequence of events: >> >> 1) the controllers are suspended: >> >> Jul 25 11:27:12 nemi kernel: [ 38.962792] uhci_hcd 0000:00:1a.2: power state changed by ACPI to D2 >> Jul 25 11:27:12 nemi kernel: [ 39.006718] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D2 >> Jul 25 11:27:15 nemi kernel: [ 41.808471] uhci_hcd 0000:00:1a.0: power state changed by ACPI to D2 >> Jul 25 11:27:15 nemi kernel: [ 41.824123] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D2 >> Jul 25 11:27:15 nemi kernel: [ 41.824194] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D2 > > Here uhci controller is put into D2 > > [snip] >> >> Doing the same with commit 448bd857d reverted: >> >> >> 1) the controllers are suspended (to state D3? instead of D2?): >> >> Jul 25 11:34:01 nemi kernel: [ 37.064955] uhci_hcd 0000:00:1a.2: power state changed by ACPI to D3 >> Jul 25 11:34:01 nemi kernel: [ 37.106586] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D3 >> Jul 25 11:34:04 nemi kernel: [ 39.808329] uhci_hcd 0000:00:1a.0: power state changed by ACPI to D3 >> Jul 25 11:34:04 nemi kernel: [ 39.840054] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D3 >> Jul 25 11:34:04 nemi kernel: [ 39.840068] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D3 > > With commit reverted, the uhci_controller is put into D3 (ACPI D3cold). > > And the uhci controller on your system may not work properly under D2 > state, while OK in D3 state, and the commit will make uhci controller > choose D2 instead of D3. > > Please try following command line before testing. > > for f in /sys/bus/pci/devices/*/d3cold_allowed; do echo 1 > $f; done That made it work. The USB controllers ended up in D4 though: Jul 25 15:52:33 nemi kernel: [ 152.753280] uhci_hcd 0000:00:1a.0: power state changed by ACPI to D0 Jul 25 15:52:33 nemi kernel: [ 152.753453] uhci_hcd 0000:00:1a.0: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.753619] uhci_hcd 0000:00:1a.0: power state changed by ACPI to D4 Jul 25 15:52:33 nemi kernel: [ 152.753875] uhci_hcd 0000:00:1a.1: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.754153] uhci_hcd 0000:00:1a.2: power state changed by ACPI to D0 Jul 25 15:52:33 nemi kernel: [ 152.754279] uhci_hcd 0000:00:1a.2: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.754432] uhci_hcd 0000:00:1a.2: power state changed by ACPI to D4 Jul 25 15:52:33 nemi kernel: [ 152.754668] ehci_hcd 0000:00:1a.7: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.768089] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D4 Jul 25 15:52:33 nemi kernel: [ 152.768573] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0 Jul 25 15:52:33 nemi kernel: [ 152.768726] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.768891] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D4 Jul 25 15:52:33 nemi kernel: [ 152.769144] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.769530] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.769902] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Jul 25 15:52:33 nemi kernel: [ 152.784189] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D4 was that expected? Anyway, waking up the controller from this state by plugging a USB device works, so it's a perfectly OK workaround. Is this something that could/should be implemented as a system specific quirk, or is the problem more generic? Even if it is a ACPI implementation issue I would expect it to be common to a number of Lenovo laptops of the same generation as mine (~2008). > And please provide the output of the following command line. > > acpidump Attached. Thanks a lot for all your help debugging this issue. Bjørn -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
