Add driver that controls the built-in USB PHY in the i.MX233/i.MX28. This enables the PHY upon powerup and shuts it down on shutdown. Signed-off-by: Marek Vasut <marex@xxxxxxx> Cc: Chen Peter-B29397 <B29397@xxxxxxxxxxxxx> Cc: Detlev Zundel <dzu@xxxxxxx> Cc: Fabio Estevam <festevam@xxxxxxxxx> Cc: Li Frank-B20596 <B20596@xxxxxxxxxxxxx> Cc: Linux USB <linux-usb@xxxxxxxxxxxxxxx> Cc: Liu JunJie-B08287 <B08287@xxxxxxxxxxxxx> Cc: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> Cc: Shawn Guo <shawn.guo@xxxxxxxxxx> Cc: Shi Make-B15407 <B15407@xxxxxxxxxxxxx> Cc: Stefano Babic <sbabic@xxxxxxx> Cc: Subodh Nijsure <snijsure@xxxxxxxxxxxx> Cc: Wolfgang Denk <wd@xxxxxxx> --- drivers/usb/otg/Kconfig | 10 ++ drivers/usb/otg/Makefile | 1 + drivers/usb/otg/mxs-phy.c | 313 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 324 insertions(+) create mode 100644 drivers/usb/otg/mxs-phy.c diff --git a/drivers/usb/otg/Kconfig b/drivers/usb/otg/Kconfig index 5c87db0..bc7625e 100644 --- a/drivers/usb/otg/Kconfig +++ b/drivers/usb/otg/Kconfig @@ -116,6 +116,16 @@ config FSL_USB2_OTG help Enable this to support Freescale USB OTG transceiver. +config USB_MXS_PHY + tristate "Freescale i.MX28 USB PHY support" + select USB_OTG_UTILS + select USB_IMX_COMPOSITE + help + Say Y here if you want to build Freescale i.MX28 USB PHY + driver in kernel. + + To compile this driver as a module, choose M here. + config USB_MV_OTG tristate "Marvell USB OTG support" depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND diff --git a/drivers/usb/otg/Makefile b/drivers/usb/otg/Makefile index 41aa509..a844b8d 100644 --- a/drivers/usb/otg/Makefile +++ b/drivers/usb/otg/Makefile @@ -20,4 +20,5 @@ obj-$(CONFIG_USB_MSM_OTG) += msm_otg.o obj-$(CONFIG_AB8500_USB) += ab8500-usb.o fsl_usb2_otg-objs := fsl_otg.o otg_fsm.o obj-$(CONFIG_FSL_USB2_OTG) += fsl_usb2_otg.o +obj-$(CONFIG_USB_MXS_PHY) += mxs-phy.o obj-$(CONFIG_USB_MV_OTG) += mv_otg.o diff --git a/drivers/usb/otg/mxs-phy.c b/drivers/usb/otg/mxs-phy.c new file mode 100644 index 0000000..eb658ca --- /dev/null +++ b/drivers/usb/otg/mxs-phy.c @@ -0,0 +1,313 @@ +/* + * drivers/usb/otg/mxs-phy.c + * + * Freescale i.MX28 USB PHY driver. + * + * Copyright (C) 2012 Marek Vasut <marex@xxxxxxx> + * on behalf of DENX Software Engineering GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> +#include <linux/slab.h> +#include <linux/delay.h> + +#include <linux/usb.h> +#include <linux/usb/ch9.h> +#include <linux/usb/otg.h> +#include <linux/usb/gadget.h> +#include <linux/usb/hcd.h> +#include <linux/usb/ehci_def.h> + +#include <mach/common.h> +#include <mach/hardware.h> +#include <mach/devices-common.h> +#include <mach/mx28.h> + +/* MXS USB PHY register definitions. */ +#define HW_USBPHY_PWD 0x00 + +#define HW_USBPHY_CTRL 0x30 +#define HW_USBPHY_CTRL_SET 0x34 +#define HW_USBPHY_CTRL_CLR 0x38 +#define HW_USBPHY_CTRL_TOG 0x3c + +#define BM_USBPHY_CTRL_SFTRST (1 << 31) +#define BM_USBPHY_CTRL_CLKGATE (1 << 30) +#define BM_USBPHY_CTRL_ENVBUSCHG_WKUP (1 << 23) +#define BM_USBPHY_CTRL_ENIDCHG_WKUP (1 << 22) +#define BM_USBPHY_CTRL_ENDPDMCHG_WKUP (1 << 21) +#define BM_USBPHY_CTRL_WAKEUP_IRQ (1 << 17) +#define BM_USBPHY_CTRL_ENIRQWAKEUP (1 << 16) +#define BM_USBPHY_CTRL_ENUTMILEVEL3 (1 << 15) +#define BM_USBPHY_CTRL_ENUTMILEVEL2 (1 << 14) +#define BM_USBPHY_CTRL_ENIRQDEVPLUGIN (1 << 11) +#define BM_USBPHY_CTRL_RESUME_IRQ (1 << 10) +#define BM_USBPHY_CTRL_ENIRQRESUMEDETECT (1 << 9) +#define BM_USBPHY_CTRL_ENOTGIDDETECT (1 << 7) +#define BM_USBPHY_CTRL_ENDEVPLUGINDETECT (1 << 4) +#define BM_USBPHY_CTRL_HOSTDISCONDETECT_IRQ (1 << 3) +#define BM_USBPHY_CTRL_ENIRQHOSTDISCON (1 << 2) +#define BM_USBPHY_CTRL_ENHOSTDISCONDETECT (1 << 1) + +#define HW_USBPHY_STATUS 0x40 + +#define BM_USBPHY_STATUS_OTGID_STATUS (1 << 8) +#define BM_USBPHY_STATUS_DEVPLUGIN_STATUS (1 << 6) +#define BM_USBPHY_STATUS_HOSTDISCON_STATUS (1 << 3) + +struct mxs_usb_phy { + struct usb_phy phy; + struct usb_otg otg; + struct clk *clk; + bool discon; +}; + +static int mxs_usb_phy_init(struct usb_phy *x) +{ + struct mxs_usb_phy *phy = container_of(x, struct mxs_usb_phy, phy); + uint32_t val; + + /* Enable clock to the PHY. */ + clk_enable(phy->clk); + + /* Reset the PHY block. */ + mxs_reset_block(x->io_priv + HW_USBPHY_CTRL); + + /* Power up the PHY. */ + writel(0, x->io_priv + HW_USBPHY_PWD); + + /* Clear the wakeup IRQ before enabling them below. */ + writel(BM_USBPHY_CTRL_RESUME_IRQ | BM_USBPHY_CTRL_WAKEUP_IRQ, + x->io_priv + HW_USBPHY_CTRL_CLR); + + /* Enable FS/LS compatibility and wakeup IRQs. */ + val = BM_USBPHY_CTRL_ENUTMILEVEL2 | BM_USBPHY_CTRL_ENUTMILEVEL3 | + BM_USBPHY_CTRL_ENIRQWAKEUP; + + /* Enable IRQ sources. */ + val |= BM_USBPHY_CTRL_ENIDCHG_WKUP | BM_USBPHY_CTRL_ENDPDMCHG_WKUP | + BM_USBPHY_CTRL_ENVBUSCHG_WKUP; + + writel(val, x->io_priv + HW_USBPHY_CTRL_SET); + + return 0; +} + +static void mxs_usb_phy_shutdown(struct usb_phy *x) +{ + struct mxs_usb_phy *phy = container_of(x, struct mxs_usb_phy, phy); + uint32_t val; + + /* Clear the wakeup IRQ before disabling them below. */ + writel(BM_USBPHY_CTRL_RESUME_IRQ | BM_USBPHY_CTRL_WAKEUP_IRQ, + x->io_priv + HW_USBPHY_CTRL_CLR); + + /* Disable FS/LS compatibility and wakeup IRQs. */ + val = BM_USBPHY_CTRL_ENUTMILEVEL2 | BM_USBPHY_CTRL_ENUTMILEVEL3 | + BM_USBPHY_CTRL_ENIRQWAKEUP; + + /* Disable IRQ sources. */ + val |= BM_USBPHY_CTRL_ENIDCHG_WKUP | BM_USBPHY_CTRL_ENDPDMCHG_WKUP | + BM_USBPHY_CTRL_ENVBUSCHG_WKUP; + + writel(val, x->io_priv + HW_USBPHY_CTRL_CLR); + + /* + * The interrupt must be disabled for at least 3 cycles of the + * standby clock (32kHz), that is 0.094 ms. + */ + udelay(100); + + /* Gate off the PHY. */ + writel(BM_USBPHY_CTRL_CLKGATE, x->io_priv + HW_USBPHY_CTRL_SET); + + /* Disable clock to the PHY. */ + clk_disable(phy->clk); +} + +static int mxs_otg_set_host(struct usb_otg *otg, struct usb_bus *host) +{ + return 0; +} + +static int mxs_otg_set_peripheral(struct usb_otg *otg, struct usb_gadget *gg) +{ + return 0; +} + +static int mxs_otg_set_vbus(struct usb_otg *otg, bool enabled) +{ + return 0; +} + +static int mxs_usb_phy_notify(struct usb_phy *x, void *data) +{ + struct mxs_usb_phy *phy = container_of(x, struct mxs_usb_phy, phy); + struct mxs_ci13xxx_phy_notify *notify = data; + + if (notify->discon == phy->discon) + return 0; + + phy->discon = notify->discon; + + if (notify->discon) { + writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT, + x->io_priv + HW_USBPHY_CTRL_CLR); + } else { + writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT, + x->io_priv + HW_USBPHY_CTRL_SET); + } + + return 0; +} + +static int __devinit mxs_phy_probe(struct platform_device *pdev) +{ + struct mxs_usb_phy *phy; + struct resource *mem_res; + void *retp; + int ret; + struct usb_otg *otg; + + /* Allocate PHY driver's private data. */ + phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL); + if (!phy) { + dev_err(&pdev->dev, "Failed to allocate USB PHY structure!\n"); + return -ENOMEM; + } + + /* Get memory area for PHY from resources. */ + mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!mem_res) { + dev_err(&pdev->dev, "Specify memory area for this USB PHY!\n"); + return -ENODEV; + } + + /* Request the memory region for this USB PHY. */ + retp = devm_request_mem_region(&pdev->dev, mem_res->start, + resource_size(mem_res), pdev->name); + if (!retp) { + dev_err(&pdev->dev, "USB PHY memory area already in use!\n"); + return -EBUSY; + } + + /* Map the memory region for USB PHY. */ + phy->phy.io_priv = devm_ioremap(&pdev->dev, mem_res->start, + resource_size(mem_res)); + if (!phy->phy.io_priv) { + dev_err(&pdev->dev, "Memory mapping of USB PHY failed!\n"); + return -EFAULT; + } + + /* Claim the PHY clock. */ + phy->clk = clk_get(&pdev->dev, "phy"); + if (!phy->clk) { + dev_err(&pdev->dev, "Failed to claim clock for USB PHY!\n"); + return PTR_ERR(phy->clk); + } + + /* Prepare PHY clock. */ + ret = clk_prepare(phy->clk); + if (ret) { + dev_err(&pdev->dev, "Failed to prepare clock for USB PHY!\n"); + goto err_prepare_phy_clock; + } + + /* Setup the PHY structures. */ + phy->phy.dev = &pdev->dev; + phy->phy.label = "mxs-usb-phy"; + phy->phy.init = mxs_usb_phy_init; + phy->phy.shutdown = mxs_usb_phy_shutdown; + phy->phy.notify = mxs_usb_phy_notify; + phy->phy.state = OTG_STATE_UNDEFINED; + + otg = &phy->otg; + phy->phy.otg = otg; + + otg->phy = &phy->phy; + otg->set_vbus = mxs_otg_set_vbus; + otg->set_host = mxs_otg_set_host; + otg->set_peripheral = mxs_otg_set_peripheral; + + platform_set_drvdata(pdev, phy); + + ATOMIC_INIT_NOTIFIER_HEAD(&phy->phy.notifier); + + /* Register the transceiver with kernel. */ + ret = usb_set_transceiver(&phy->phy); + if (ret) { + dev_err(&pdev->dev, "Can't register transceiver, (%d)\n", ret); + goto err_set_transceiver; + } + + return 0; + +err_set_transceiver: + clk_unprepare(phy->clk); +err_prepare_phy_clock: + clk_put(phy->clk); + return ret; +} + +static int __devexit mxs_phy_remove(struct platform_device *pdev) +{ + struct mxs_usb_phy *phy = platform_get_drvdata(pdev); + + /* Power down the PHY. */ + mxs_usb_phy_shutdown(&phy->phy); + + /* Remove the transceiver. */ + usb_set_transceiver(NULL); + + /* Stop the PHY clock. */ + clk_disable_unprepare(phy->clk); + clk_put(phy->clk); + + /* Free the rest. */ + platform_set_drvdata(pdev, NULL); + + return 0; +} + +static struct platform_driver mxs_phy_driver = { + .probe = mxs_phy_probe, + .remove = __devexit_p(mxs_phy_remove), + .driver = { + .name = "mxs-usb-phy", + .owner = THIS_MODULE, + }, +}; + +static int __init mxs_phy_init(void) +{ + return platform_driver_register(&mxs_phy_driver); +} + +static void __exit mxs_phy_exit(void) +{ + platform_driver_unregister(&mxs_phy_driver); +} + +arch_initcall(mxs_phy_init); +module_exit(mxs_phy_exit); + +MODULE_ALIAS("platform:mxs-usb-phy"); +MODULE_AUTHOR("Marek Vasut <marex@xxxxxxx>"); +MODULE_DESCRIPTION("Freescale i.MX28 USB PHY driver"); +MODULE_LICENSE("GPL"); -- 1.7.10 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html