Re: [PATCH RESEND] ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, May 3, 2012 at 11:03 PM, Igor Grinberg <grinberg@xxxxxxxxxxxxxx> wrote:
> Hi Russ,
>
> On 05/03/12 22:08, Russ Dill wrote:
>> On Wed, May 2, 2012 at 3:38 AM, Raja, Govindraj <govindraj.raja@xxxxxx> wrote:
>>> On Wed, May 2, 2012 at 2:17 PM, Russ Dill <Russ.Dill@xxxxxx> wrote:
>>>> On Mon, Mar 19, 2012 at 6:34 AM, Raja, Govindraj <govindraj.raja@xxxxxx> wrote:
>>>>> On Mon, Mar 19, 2012 at 12:12 PM, Keshava Munegowda
>>>>> <keshava_mgowda@xxxxxx> wrote:
>>>>>> From: Keshava Munegowda <Keshava_mgowda@xxxxxx>
>>>>>>
>>>>>> It is observed that the echi ports of 3430 sdp board
>>>>>> are not working due to the random timing of programming
>>>>>> the associated GPIOs of the ULPI PHYs of the EHCI for reset.
>>>>>> If the PHYs are reset at during usbhs core driver, host ports will
>>>>>> not work because EHCI driver is loaded after the resetting PHYs.
>>>>>> The PHYs should be in reset state while initializing the EHCI
>>>>>> controller.
>>>>>> The code which does the GPIO pins associated with the PHYs
>>>>>> are programmed to reset is moved from the USB host core driver
>>>>>> to EHCI driver.
>>>>>
>>>>> I tested on beagle xm where gpio nreset is requested from
>>>>> board file.
>>>>> (Basic enumertaion after gpio nreset seems to work fine,
>>>>> Hub and smsc lan chip get detected afetr boot up)
>>>>>
>>>>
>>>> What base did you test this on top of? my xM is failing USB-wise when
>>>> I apply this on v3.3.3 (with the UART mux fix patch) and where it is
>>>> applied within master (3.4-rc4, again, with the UART mux fix patch).
>>>> Additionally, reverting this patch from 3.4-rc5 causes rc5 to work
>>>> properly.
>>>>
>>>
>>> Works for me be on 3.4-rc5 Beagle-XM even without reverting the patch
>>>
>>> Logs as in here [1].
>>>
>>> --
>>> Thanks,
>>> Govindraj.R
>>>
>>> [1]:
>>> http://pastebin.pandaboard.org/index.php/view/20343533
>>
>> I've tracked down the difference. I'm loading my uEnv.txt and uImage
>> in u-boot from the network which means initializing USB. You are
>> loading straight from MMC. If I switch to loading straight from MMC
>> everything works.
>>
>> Can everyone do a 'usb start' in u-boot before booting and re-test?
>> I'm pretty sure this is a regression, but the bug could be a strange
>> u-boot/kernel interaction.
>
> Probably, kernel code does not reinitialize EHCI correctly if it was already enabled?
> Can you try the below sequence:
> usb start
> usb stop
> boot Linux

That doesn't work. Rebooting does work though.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux