Fix abuse of interface data which was used to signal device disconnect.
Use the usb_serial disconnect flag and mutex where appropriate.
Note that there's no need to grab the mutex in chase_port as it does not
access the device.
Signed-off-by: Johan Hovold <jhovold@xxxxxxxxx>
---
drivers/usb/serial/io_ti.c | 17 ++++++++++++-----
1 files changed, 12 insertions(+), 5 deletions(-)
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index 40a95a7..da02faf 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -547,6 +547,7 @@ static void chase_port(struct edgeport_port *port, unsigned long timeout,
{
int baud_rate;
struct tty_struct *tty = tty_port_tty_get(&port->port->port);
+ struct usb_serial *serial = port->port->serial;
wait_queue_t wait;
unsigned long flags;
@@ -561,7 +562,7 @@ static void chase_port(struct edgeport_port *port, unsigned long timeout,
set_current_state(TASK_INTERRUPTIBLE);
if (kfifo_len(&port->write_fifo) == 0
|| timeout == 0 || signal_pending(current)
- || !usb_get_intfdata(port->port->serial->interface))
+ || serial->disconnected)
/* disconnect */
break;
spin_unlock_irqrestore(&port->ep_lock, flags);
@@ -578,7 +579,7 @@ static void chase_port(struct edgeport_port *port, unsigned long timeout,
/* wait for data to drain from the device */
timeout += jiffies;
while ((long)(jiffies - timeout) < 0 && !signal_pending(current)
- && usb_get_intfdata(port->port->serial->interface)) {
+ && serial->disconnected) {
/* not disconnected */
if (!tx_active(port))
break;
@@ -586,7 +587,7 @@ static void chase_port(struct edgeport_port *port, unsigned long timeout,
}
/* disconnected */
- if (!usb_get_intfdata(port->port->serial->interface))
+ if (serial->disconnected)
return;
/* wait one more character time, based on baud rate */
@@ -2003,8 +2004,8 @@ static void edge_close(struct usb_serial_port *port)
{
struct edgeport_serial *edge_serial;
struct edgeport_port *edge_port;
+ struct usb_serial *serial = port->serial;
int port_number;
- int status;
dbg("%s - port %d", __func__, port->number);
@@ -2028,12 +2029,18 @@ static void edge_close(struct usb_serial_port *port)
* send a close port command to it */
dbg("%s - send umpc_close_port", __func__);
port_number = port->number - port->serial->minor;
- status = send_cmd(port->serial->dev,
+
+ mutex_lock(&serial->disc_mutex);
+ if (!serial->disconnected) {
+ send_cmd(serial->dev,
UMPC_CLOSE_PORT,
(__u8)(UMPM_UART1_PORT + port_number),
0,
NULL,
0);
+ }
+ mutex_unlock(&serial->disc_mutex);
+
mutex_lock(&edge_serial->es_lock);
--edge_port->edge_serial->num_ports_open;
if (edge_port->edge_serial->num_ports_open <= 0) {
--
1.7.8.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
