Hello. On 15-09-2011 18:19, Kishon Vijay Abraham I wrote:
Setting OTG_INTERFSEL to UTMI interferes with charger detection resulting in incorrect detection of charger type. Hence OTG_INTERFSEL is configured to ULPI initially and changed to UTMI only after receiving USB_EVENT_ID or USB_EVENT_VBUS notification.
Signed-off-by: Kishon Vijay Abraham I<kishon@xxxxxx> Signed-off-by: Balaji T K<balajitk@xxxxxx>
AFAIK, full name is needed here.
[sandesh.gowda@xxxxxx: The interface selection has to be done before the PHY is activated and is not allowed to change when the PHY clock is already running]
No signoff from him?
--- drivers/usb/musb/omap2430.c | 50 +++++++++++++++++++++++++++++++++++------- 1 files changed, 41 insertions(+), 9 deletions(-)
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index fc9377c..724450b 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -228,6 +228,7 @@ static inline void omap2430_low_level_init(struct musb *musb) static int musb_otg_notifications(struct notifier_block *nb, unsigned long event, void *unused) { + u32 val; struct musb *musb = container_of(nb, struct musb, nb); struct device *dev = musb->controller; struct musb_hdrc_platform_data *pdata = dev->platform_data; @@ -240,11 +241,32 @@ static int musb_otg_notifications(struct notifier_block *nb, if (is_otg_enabled(musb)) { if (musb->gadget_driver) { pm_runtime_get_sync(musb->controller); + + val = musb_readl(musb->mregs, OTG_INTERFSEL); + if (data->interface_type == + MUSB_INTERFACE_UTMI) { + val&= ~ULPI_12PIN; + val |= UTMI_8BIT; + } else { + val |= ULPI_12PIN; + } + musb_writel(musb->mregs, OTG_INTERFSEL, val); + usb_phy_init(musb->xceiv); omap2430_musb_set_vbus(musb, 1); } } else { pm_runtime_get_sync(musb->controller); + + val = musb_readl(musb->mregs, OTG_INTERFSEL); + if (data->interface_type == MUSB_INTERFACE_UTMI) { + val&= ~ULPI_12PIN; + val |= UTMI_8BIT; + } else { + val |= ULPI_12PIN; + } + musb_writel(musb->mregs, OTG_INTERFSEL, val); + usb_phy_init(musb->xceiv); omap2430_musb_set_vbus(musb, 1); } @@ -255,6 +277,16 @@ static int musb_otg_notifications(struct notifier_block *nb, if (musb->gadget_driver) pm_runtime_get_sync(musb->controller); + + val = musb_readl(musb->mregs, OTG_INTERFSEL); + if (data->interface_type == MUSB_INTERFACE_UTMI) { + val&= ~ULPI_12PIN; + val |= UTMI_8BIT; + } else { + val |= ULPI_12PIN; + } + musb_writel(musb->mregs, OTG_INTERFSEL, val); + usb_phy_init(musb->xceiv); break;
Why repeat the same sequence 3 times. Couldn't you factor it out into a subroutine?
@@ -272,6 +304,11 @@ static int musb_otg_notifications(struct notifier_block *nb, otg_set_vbus(musb->xceiv->otg, 0); } usb_phy_shutdown(musb->xceiv); + + val = musb_readl(musb->mregs, OTG_INTERFSEL); + val |= ULPI_12PIN; + musb_writel(musb->mregs, OTG_INTERFSEL, val); + break; default: dev_dbg(musb->controller, "ID float\n"); @@ -304,16 +341,11 @@ static int omap2430_musb_init(struct musb *musb) goto err1; } + /* Set OTG_INTERFSEL to ULPI for correct charger detection. + * This should be later set to UTMI. + */ l = musb_readl(musb->mregs, OTG_INTERFSEL); - - if (data->interface_type == MUSB_INTERFACE_UTMI) { - /* OMAP4 uses Internal PHY GS70 which uses UTMI interface */ - l&= ~ULPI_12PIN; /* Disable ULPI */ - l |= UTMI_8BIT; /* Enable UTMI */ - } else { - l |= ULPI_12PIN; - } - + l |= ULPI_12PIN; musb_writel(musb->mregs, OTG_INTERFSEL, l);
This also seems to be the same code repeated twice... WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html