If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@xxxxxxx>
---
drivers/usb/core/driver.c | 14 ++++++++
drivers/usb/core/hub.c | 9 +++++
drivers/usb/core/usb.h | 5 +++
drivers/usb/host/xhci-hub.c | 9 +++++
drivers/usb/host/xhci-pci.c | 1 +
drivers/usb/host/xhci.c | 74 ++++++++++++++++++++++++++++++++++++++++++-
drivers/usb/host/xhci.h | 4 ++
include/linux/usb.h | 4 ++
include/linux/usb/hcd.h | 1 +
9 files changed, 120 insertions(+), 1 deletions(-)
diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
index 34e3da5..6865a82 100644
--- a/drivers/usb/core/driver.c
+++ b/drivers/usb/core/driver.c
@@ -1700,6 +1700,20 @@ int usb_runtime_idle(struct device *dev)
return 0;
}
+int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
+{
+ struct usb_hcd *hcd = bus_to_hcd(udev->bus);
+ int ret = -EPERM;
+
+ if (hcd->driver->set_usb2_hw_lpm) {
+ ret = hcd->driver->set_usb2_hw_lpm(hcd, udev, enable);
+ if (!ret)
+ udev->usb2_hw_lpm_enabled = enable;
+ }
+
+ return ret;
+}
+
#endif /* CONFIG_USB_SUSPEND */
struct bus_type usb_bus_type = {
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 1a98cb8..3354fe3 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -2347,6 +2347,10 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
}
}
+ /* disable USB2 hardware LPM */
+ if (udev->usb2_hw_lpm_enabled == 1)
+ usb_set_usb2_hardware_lpm(udev, 0);
+
/* see 7.1.7.6 */
if (hub_is_superspeed(hub->hdev))
status = set_port_feature(hub->hdev,
@@ -2558,7 +2562,12 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg)
if (status < 0) {
dev_dbg(&udev->dev, "can't resume, status %d\n", status);
hub_port_logical_disconnect(hub, port1);
+ } else {
+ /* Try to enable USB2 hardware LPM */
+ if (udev->usb2_hw_lpm_capable == 1)
+ usb_set_usb2_hardware_lpm(udev, 1);
}
+
return status;
}
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 0d023cd..3888778 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -82,6 +82,7 @@ extern int usb_remote_wakeup(struct usb_device *dev);
extern int usb_runtime_suspend(struct device *dev);
extern int usb_runtime_resume(struct device *dev);
extern int usb_runtime_idle(struct device *dev);
+extern int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable);
#else
@@ -96,6 +97,10 @@ static inline int usb_remote_wakeup(struct usb_device *udev)
return 0;
}
+static inline int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
+{
+ return 0;
+}
#endif
extern struct bus_type usb_bus_type;
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index aec098a..9dbfa93 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -574,10 +574,19 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
+ if ((temp & PORT_PLS_MASK) != XDEV_U0) {
+ /* Resume the port to U0 first */
+ xhci_set_link_state(xhci, port_array, wIndex,
+ XDEV_U0);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ msleep(10);
+ spin_lock_irqsave(&xhci->lock, flags);
+ }
/* In spec software should not attempt to suspend
* a port unless the port reports that it is in the
* enabled (PED = ‘1’,PLS < ‘3’) state.
*/
+ temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
|| (temp & PORT_PLS_MASK) >= XDEV_U3) {
xhci_warn(xhci, "USB core suspending device "
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 1516fe5..cac9bfb 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -348,6 +348,7 @@ static const struct hc_driver xhci_pci_hc_driver = {
* call back when device connected and addressed
*/
.update_device = xhci_update_device,
+ .set_usb2_hw_lpm = xhci_set_usb2_hardware_lpm,
};
/*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 2bfadd7..7b944a2 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -2704,6 +2704,11 @@ void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev)
del_timer_sync(&virt_dev->eps[i].stop_cmd_timer);
}
+ if (udev->usb2_hw_lpm_enabled) {
+ xhci_set_usb2_hardware_lpm(hcd, udev, 0);
+ udev->usb2_hw_lpm_enabled = 0;
+ }
+
spin_lock_irqsave(&xhci->lock, flags);
/* Don't disable the slot if the host controller is dead. */
state = xhci_readl(xhci, &xhci->op_regs->status);
@@ -3117,20 +3122,87 @@ finish:
return ret;
}
+int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
+ struct usb_device *udev, int enable)
+{
+ struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ __le32 __iomem **port_array;
+ __le32 __iomem *pm_addr;
+ u32 temp;
+ unsigned int port_num;
+ unsigned long flags;
+ int u2del, hird;
+
+ if (hcd->speed == HCD_USB3 || !xhci->hw_lpm_support ||
+ !udev->lpm_capable)
+ return -EPERM;
+
+ if (!udev->parent || udev->parent->parent ||
+ udev->descriptor.bDeviceClass == USB_CLASS_HUB)
+ return -EPERM;
+
+ if (udev->usb2_hw_lpm_capable != 1)
+ return -EPERM;
+
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ port_array = xhci->usb2_ports;
+ port_num = udev->portnum - 1;
+ pm_addr = port_array[port_num] + 1;
+ temp = xhci_readl(xhci, pm_addr);
+
+ xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
+ enable ? "enable" : "disable", port_num);
+
+ u2del = HCS_U2_LATENCY(xhci->hcs_params3);
+ if (le32_to_cpu(udev->bos->ext_cap->bmAttributes) & (1 << 2))
+ hird = xhci_calculate_hird_besl(u2del, 1);
+ else
+ hird = xhci_calculate_hird_besl(u2del, 0);
+
+ if (enable) {
+ temp &= ~PORT_HIRD_MASK;
+ temp |= PORT_HIRD(hird) | PORT_RWE;
+ xhci_writel(xhci, temp, pm_addr);
+ temp = xhci_readl(xhci, pm_addr);
+ temp |= PORT_HLE;
+ xhci_writel(xhci, temp, pm_addr);
+ } else {
+ temp &= ~(PORT_HLE | PORT_RWE | PORT_HIRD_MASK);
+ xhci_writel(xhci, temp, pm_addr);
+ }
+
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ return 0;
+}
+
int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int ret;
ret = xhci_usb2_software_lpm_test(hcd, udev);
- if (!ret)
+ if (!ret) {
xhci_dbg(xhci, "software LPM test succeed\n");
+ if (xhci->hw_lpm_support == 1) {
+ udev->usb2_hw_lpm_capable = 1;
+ ret = xhci_set_usb2_hardware_lpm(hcd, udev, 1);
+ if (!ret)
+ udev->usb2_hw_lpm_enabled = 1;
+ }
+ }
return 0;
}
#else
+int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
+ struct usb_device *udev, int enable)
+{
+ return 0;
+}
+
int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
{
return 0;
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 9a94308..978154b 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -367,7 +367,9 @@ struct xhci_op_regs {
#define PORT_L1S_SUCCESS 1
#define PORT_RWE (1 << 3)
#define PORT_HIRD(p) (((p) & 0xf) << 4)
+#define PORT_HIRD_MASK (0xf << 4)
#define PORT_L1DS(p) (((p) & 0xff) << 8)
+#define PORT_HLE (1 << 16)
/**
* struct xhci_intr_reg - Interrupt Register Set
@@ -1532,6 +1534,8 @@ int xhci_free_streams(struct usb_hcd *hcd, struct usb_device *udev,
gfp_t mem_flags);
int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev);
int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev);
+int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
+ struct usb_device *udev, int enable);
int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
struct usb_tt *tt, gfp_t mem_flags);
int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags);
diff --git a/include/linux/usb.h b/include/linux/usb.h
index cf13924..8f4e567 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -411,6 +411,8 @@ struct usb_tt;
* @authenticated: Crypto authentication passed
* @wusb: device is Wireless USB
* @lpm_capable: device supports LPM
+ * @usb2_hw_lpm_capable: device can perform USB2 hardware LPM
+ * @usb2_hw_lpm_enabled: USB2 hardware LPM enabled
* @string_langid: language ID for strings
* @product: iProduct string, if present (static)
* @manufacturer: iManufacturer string, if present (static)
@@ -474,6 +476,8 @@ struct usb_device {
unsigned authenticated:1;
unsigned wusb:1;
unsigned lpm_capable:1;
+ unsigned usb2_hw_lpm_capable:1;
+ unsigned usb2_hw_lpm_enabled:1;
int string_langid;
/* static strings from the device */
diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h
index 0097136..a4cd6c5 100644
--- a/include/linux/usb/hcd.h
+++ b/include/linux/usb/hcd.h
@@ -343,6 +343,7 @@ struct hc_driver {
* address is set
*/
int (*update_device)(struct usb_hcd *, struct usb_device *);
+ int (*set_usb2_hw_lpm)(struct usb_hcd *, struct usb_device *, int);
};
extern int usb_hcd_link_urb_to_ep(struct usb_hcd *hcd, struct urb *urb);
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
