On Wed, 2011-07-27 at 16:12 +0200, Phil Sutter wrote: > Hello everyone, > > I am testing the above module on linux-2.6.39.2 which should contain the > latest changes to at least sierra_net.c. Although I am able to bring the > module up and then can get traffic through it, initialisation seems to > be a little picky. I wonder if the firmware changed and Sierra hasn't updated the driver yet. I've got a usb306 which also uses sierra_net which doesn't have this problem. It looks like the driver tries to sync with the firmware right after binding to the net interface, so that means at least a couple of SYNC requests have already happened by the time you start getting errors. My first thought here is simply that the firmware on the MC7700 doesn't work like the rest of the devices that sierra_net expects, and for that you'd have to get Sierra to weigh in on the required changes :( Since the MC7700 is an LTE module it's 100% likely the firmware is different, or at least significantly rebased, from the existing Sierra HSPA/EVDO parts that use sierra_net and thus I wouldn't necessarily expect it to work out of the box. Dan > After connecting the module via USB, I get the following final > initialisation message: > | Jul 27 14:01:15 (none) user.info kernel: [166371.982356] sierra_net 1-1:1.7: wwan0: register 'sierra_net' at usb-0000:00:08.2-1, Sierra Wireless USB-to-WWAN Modem, 4a:82:22:b9:05:07 > > Doing nothing (successfully), the driver starts printing errors after a > while: > | Jul 27 14:02:15 (none) user.err kernel: [166432.201461] sierra_net 1-1:1.7: wwan0: Submit SYNC failed -32 > | Jul 27 14:02:15 (none) user.err kernel: [166432.201609] sierra_net 1-1:1.7: wwan0: Send SYNC failed, status -32 > | Jul 27 14:02:15 (none) user.err kernel: [166432.205446] sierra_net 1-1:1.7: wwan0: Submit SYNC failed -32 > | Jul 27 14:02:15 (none) user.err kernel: [166432.205590] sierra_net 1-1:1.7: wwan0: Send SYNC failed, status -32 > > The above messages are the first ones to appear (so there's a delay of > 60 seconds in between), and they repeat each 2 seconds from then on. > Depending on how I continue at that point, results vary: > > a) 'ip link set wwan0 up': setting the interface up stops the above error > messages from being printed. This worked every time I tried. > > b) Sending 'ATZ' on the control-tty: this makes the error-messages > disappear for about 6 seconds, so two iterations of the sync-timer > seem to succeed. When I then try to continue initialisation, I usually > get to 'AT+C' (for AT+CPIN='1234'), then the control-tty dies (neither > echoing of typed characters, nor feedback from the modem printed). > > Trying a) from the state after b) indeed makes the error-messages go > away, but the tty stays dead until I power-cycle the module. Needless to > say, without the control-tty the module is completely useless. > > My first thought was that the driver shouldn't try to SYNC while the > interface being down, but apparently sierra_net_send_sync() doesn't get > called anymore after setting the interface up. > > So in order to prevent the module from dieing, I need to up the > interface before initialisation via AT-interface. > > Another interesting aspect: the above error stays gone after the > interface has been upped once, even if it's brought down right > afterwards without doing anything else. OK, not completely - there needs > to be a little delay in which the interface stays up, but a tenth of a > second was enough. > > What else can I do to track this problem down further? What additional > information do you need from me? Any advice is highly appreciated, of > course! > > Greetings, Phil > -- > To unsubscribe from this list: send the line "unsubscribe netdev" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
