On 19/03/11 16:57, Alan Stern wrote:
The transcripts are not complete. Please run the tests again and post
the entire output from the dmesg command instead of just the tail of
the kernel log.
Also, for the "bad" kernel you should enable CONFIG_USB_STORAGE_DEBUG.
Please find transcripts/dmesg of fresh tests.
The short transcripts show the commands I ran. I've included the tail of
dmesg at appropriate points so that you can relate plugging/enabling to
the complete dmesg output, which was captured at the end of the session.
--
Regards,
Richard
Script started on Sun 20 Mar 2011 15:06:03 GMT
root@calder:~# # plugging in device but not enabled
root@calder:~# dmesg | tail
[ 90.540060] usb 6-1: device descriptor read/64, error -71
[ 90.780070] usb 6-1: device descriptor read/64, error -71
[ 91.010047] usb 6-1: new full speed USB device using uhci_hcd and address 3
[ 91.140045] usb 6-1: device descriptor read/64, error -71
[ 91.380070] usb 6-1: device descriptor read/64, error -71
[ 91.610078] usb 6-1: new full speed USB device using uhci_hcd and address 4
[ 92.030046] usb 6-1: device not accepting address 4, error -71
[ 92.150071] usb 6-1: new full speed USB device using uhci_hcd and address 5
[ 92.570068] usb 6-1: device not accepting address 5, error -71
[ 92.570122] hub 6-0:1.0: unable to enumerate USB device on port 1
root@calder:~# # enabling device (and waiting a few seconds)
root@calder:~# dmesg | tail
[ 120.979966] usb-storage: Bulk data transfer result 0x3
[ 120.979968] usb-storage: Attempting to get CSW...
[ 120.979970] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.980203] usb-storage: Status code 0; transferred 12/13
[ 120.980205] usb-storage: -- short transfer
[ 120.980208] usb-storage: Bulk status result = 1
[ 120.980210] usb-storage: -- transport indicates error, resetting
[ 120.980217] usb-storage: usb_stor_pre_reset
[ 121.120090] usb 2-3: reset high speed USB device using ehci_hcd and address 3
[ 136.240062] usb 2-3: device descriptor read/64, error -110
root@calder:~# fdisk -l
Disk /dev/sda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x47c7fe89
Device Boot Start End Blocks Id System
/dev/sda1 * 1 1245 10000431 83 Linux
/dev/sda2 1246 14400 105667537+ 83 Linux
/dev/sda3 14401 14593 1550272+ 82 Linux swap / Solaris
root@calder:~# lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04f2:b070 Chicony Electronics Co., Ltd
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@calder:~# # lsusb hung until device was unplugged
root@calder:~# # about to run complete dmesg ...
root@calder:~# exit
Script done on Sun 20 Mar 2011 15:08:29 GMT
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.37-baddbg+ (root@calder) (gcc version 4.5.2 (Ubuntu/Linaro 4.5.2-6ubuntu4) ) #15 SMP Sat Mar 19 19:07:07 GMT 2011
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.37-baddbg+ root=UUID=51e6266e-2230-442b-8cfa-3708c9a6a51b ro single
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f4de000 (usable)
[ 0.000000] BIOS-e820: 000000007f4de000 - 000000007f4e9000 (reserved)
[ 0.000000] BIOS-e820: 000000007f4e9000 - 000000007f543000 (usable)
[ 0.000000] BIOS-e820: 000000007f543000 - 000000007f546000 (reserved)
[ 0.000000] BIOS-e820: 000000007f546000 - 000000007f5bb000 (usable)
[ 0.000000] BIOS-e820: 000000007f5bb000 - 000000007f5bf000 (reserved)
[ 0.000000] BIOS-e820: 000000007f5bf000 - 000000007f66a000 (usable)
[ 0.000000] BIOS-e820: 000000007f66a000 - 000000007f6bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f6bf000 - 000000007f700000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007f700000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.4 present.
[ 0.000000] DMI: Base Board Product Name/EQUIUM L350, BIOS 1.30 03/19/2008
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7f66a max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFFE0000 mask FFFFE0000 write-protect
[ 0.000000] 1 base 000000000 mask FC0000000 write-back
[ 0.000000] 2 base 040000000 mask FC0000000 write-back
[ 0.000000] 3 base 07F800000 mask FFF800000 uncachable
[ 0.000000] 4 base 07F700000 mask FFFF00000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [ffff8800000fe230] fe230
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f66a000
[ 0.000000] 0000000000 - 007f600000 page 2M
[ 0.000000] 007f600000 - 007f66a000 page 4k
[ 0.000000] kernel direct mapping tables up to 7f66a000 @ 1fffc000-20000000
[ 0.000000] RAMDISK: 36708000 - 3737c000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 TOSINV)
[ 0.000000] ACPI: XSDT 000000007f6fe120 00064 (v01 TOSINV TOSINV00 00000001 01000013)
[ 0.000000] ACPI: FACP 000000007f6fd000 000F4 (v04 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: DSDT 000000007f6f5000 078BB (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: FACS 000000007f675000 00040
[ 0.000000] ACPI: APIC 000000007f6f4000 00068 (v02 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: HPET 000000007f6f3000 00038 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: MCFG 000000007f6f2000 0003C (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: ASF! 000000007f6f1000 000A5 (v32 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: SLIC 000000007f6f0000 00176 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: BOOT 000000007f6ef000 00028 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 000000007f6ee000 004C4 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f66a000
[ 0.000000] Initmem setup node 0 0000000000000000-000000007f66a000
[ 0.000000] NODE_DATA [000000007f4d9000 - 000000007f4ddfff]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff88007cc00000-ffff88007e7fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[5] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007f4de
[ 0.000000] 0: 0x0007f4e9 -> 0x0007f543
[ 0.000000] 0: 0x0007f546 -> 0x0007f5bb
[ 0.000000] 0: 0x0007f5bf -> 0x0007f66a
[ 0.000000] On node 0 totalpages: 521703
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3921 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7079 pages used for memmap
[ 0.000000] DMA32 zone: 510641 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007f4de000 - 000000007f4e9000
[ 0.000000] PM: Registered nosave memory: 000000007f543000 - 000000007f546000
[ 0.000000] PM: Registered nosave memory: 000000007f5bb000 - 000000007f5bf000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007f200000 s83648 r8192 d22848 u1048576
[ 0.000000] pcpu-alloc: s83648 r8192 d22848 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 514562
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.37-baddbg+ root=UUID=51e6266e-2230-442b-8cfa-3708c9a6a51b ro single
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2031776k/2087336k available (5800k kernel code, 524k absent, 55036k reserved, 5123k data, 932k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:512 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 20971520 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1728.970 MHz processor.
[ 0.010005] Calibrating delay loop (skipped), value calculated using timer frequency.. 3457.94 BogoMIPS (lpj=17289700)
[ 0.010016] pid_max: default: 32768 minimum: 301
[ 0.010052] Security Framework initialized
[ 0.010071] AppArmor: AppArmor initialized
[ 0.010392] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.011919] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.012662] Mount-cache hash table entries: 256
[ 0.012869] Initializing cgroup subsys ns
[ 0.012880] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.012888] Initializing cgroup subsys cpuacct
[ 0.012896] Initializing cgroup subsys memory
[ 0.012910] Initializing cgroup subsys devices
[ 0.012914] Initializing cgroup subsys freezer
[ 0.012919] Initializing cgroup subsys net_cls
[ 0.012924] Initializing cgroup subsys blkio
[ 0.012976] CPU: Physical Processor ID: 0
[ 0.012980] CPU: Processor Core ID: 0
[ 0.012985] mce: CPU supports 6 MCE banks
[ 0.012996] CPU0: Thermal monitoring handled by SMI
[ 0.013002] using mwait in idle threads.
[ 0.020057] ACPI: Core revision 20101013
[ 0.040015] ftrace: allocating 22505 entries in 89 pages
[ 0.050080] Setting APIC routing to flat
[ 0.050437] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.154812] CPU0: Intel(R) Pentium(R) Dual CPU T2370 @ 1.73GHz stepping 0d
[ 0.160000] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.160000] PEBS disabled due to CPU errata.
[ 0.160000] ... version: 2
[ 0.160000] ... bit width: 40
[ 0.160000] ... generic registers: 2
[ 0.160000] ... value mask: 000000ffffffffff
[ 0.160000] ... max period: 000000007fffffff
[ 0.160000] ... fixed-purpose events: 3
[ 0.160000] ... event mask: 0000000700000003
[ 0.160000] Booting Node 0, Processors #1 Ok.
[ 0.020000] CPU1: Thermal monitoring handled by SMI
[ 0.320021] Brought up 2 CPUs
[ 0.320030] Total of 2 processors activated (6916.35 BogoMIPS).
[ 0.320466] devtmpfs: initialized
[ 0.320989] regulator: core version 0.5
[ 0.321048] regulator: dummy:
[ 0.321077] Time: 15:05:10 Date: 03/20/11
[ 0.321128] NET: Registered protocol family 16
[ 0.321273] ACPI: bus type pci registered
[ 0.321370] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.321379] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.338459] PCI: Using configuration type 1 for base access
[ 0.339344] bio: create slab <bio-0> at 0
[ 0.341676] ACPI: EC: Look up EC in DSDT
[ 0.343831] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.345359] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.346148] ACPI: SSDT 000000007f674c90 00232 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.346657] ACPI: Dynamic OEM Table Load:
[ 0.346664] ACPI: SSDT (null) 00232 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.347002] ACPI: SSDT 000000007f673610 005B3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.347485] ACPI: Dynamic OEM Table Load:
[ 0.347491] ACPI: SSDT (null) 005B3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.400398] ACPI: SSDT 000000007f674f10 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.400889] ACPI: Dynamic OEM Table Load:
[ 0.400896] ACPI: SSDT (null) 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.401065] ACPI: SSDT 000000007f676d10 00083 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.401550] ACPI: Dynamic OEM Table Load:
[ 0.401556] ACPI: SSDT (null) 00083 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.460339] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 0.600074] ACPI: Interpreter enabled
[ 0.600081] ACPI: (supports S0 S3 S4 S5)
[ 0.600117] ACPI: Using IOAPIC for interrupt routing
[ 0.610886] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.612966] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.613116] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.614335] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.621028] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.621087] ACPI: Power Resource [FN00] (on)
[ 0.621286] ACPI: No dock devices found.
[ 0.621293] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.621953] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 0.621968] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.621970] _OSC request data:1 8 1f
[ 0.621976] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.623126] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.623133] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.623139] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.623147] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
[ 0.623169] pci 0000:00:00.0: [8086:2a00] type 0 class 0x000600
[ 0.623229] pci 0000:00:02.0: [8086:2a02] type 0 class 0x000300
[ 0.623248] pci 0000:00:02.0: reg 10: [mem 0x93100000-0x931fffff 64bit]
[ 0.623259] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
[ 0.623268] pci 0000:00:02.0: reg 20: [io 0x6110-0x6117]
[ 0.623312] pci 0000:00:02.1: [8086:2a03] type 0 class 0x000380
[ 0.623328] pci 0000:00:02.1: reg 10: [mem 0x93200000-0x932fffff 64bit]
[ 0.623429] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
[ 0.623490] pci 0000:00:1a.0: reg 20: [io 0x60c0-0x60df]
[ 0.623534] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
[ 0.623595] pci 0000:00:1a.1: reg 20: [io 0x60a0-0x60bf]
[ 0.623656] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
[ 0.623684] pci 0000:00:1a.7: reg 10: [mem 0x96404c00-0x96404fff]
[ 0.623787] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.623793] pci 0000:00:1a.7: PME# disabled
[ 0.623830] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
[ 0.623853] pci 0000:00:1b.0: reg 10: [mem 0x96400000-0x96403fff 64bit]
[ 0.623939] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.623945] pci 0000:00:1b.0: PME# disabled
[ 0.623975] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
[ 0.624062] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.624068] pci 0000:00:1c.0: PME# disabled
[ 0.624101] pci 0000:00:1c.1: [8086:2841] type 1 class 0x000604
[ 0.624188] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.624194] pci 0000:00:1c.1: PME# disabled
[ 0.624230] pci 0000:00:1c.4: [8086:2847] type 1 class 0x000604
[ 0.624317] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.624323] pci 0000:00:1c.4: PME# disabled
[ 0.624356] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
[ 0.624418] pci 0000:00:1d.0: reg 20: [io 0x6080-0x609f]
[ 0.624462] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
[ 0.624523] pci 0000:00:1d.1: reg 20: [io 0x6060-0x607f]
[ 0.624568] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
[ 0.624629] pci 0000:00:1d.2: reg 20: [io 0x6040-0x605f]
[ 0.624688] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
[ 0.624716] pci 0000:00:1d.7: reg 10: [mem 0x96404800-0x96404bff]
[ 0.624818] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.624824] pci 0000:00:1d.7: PME# disabled
[ 0.624852] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.624941] pci 0000:00:1f.0: [8086:2815] type 0 class 0x000601
[ 0.625051] pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.625060] pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO
[ 0.625070] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f)
[ 0.625078] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0007)
[ 0.625127] pci 0000:00:1f.1: [8086:2850] type 0 class 0x000101
[ 0.625146] pci 0000:00:1f.1: reg 10: [io 0x6108-0x610f]
[ 0.625160] pci 0000:00:1f.1: reg 14: [io 0x6124-0x6127]
[ 0.625174] pci 0000:00:1f.1: reg 18: [io 0x6100-0x6107]
[ 0.625188] pci 0000:00:1f.1: reg 1c: [io 0x6120-0x6123]
[ 0.625201] pci 0000:00:1f.1: reg 20: [io 0x60e0-0x60ef]
[ 0.625258] pci 0000:00:1f.2: [8086:2829] type 0 class 0x000106
[ 0.625285] pci 0000:00:1f.2: reg 10: [io 0x60f8-0x60ff]
[ 0.625298] pci 0000:00:1f.2: reg 14: [io 0x611c-0x611f]
[ 0.625310] pci 0000:00:1f.2: reg 18: [io 0x60f0-0x60f7]
[ 0.625323] pci 0000:00:1f.2: reg 1c: [io 0x6118-0x611b]
[ 0.625335] pci 0000:00:1f.2: reg 20: [io 0x6020-0x603f]
[ 0.625348] pci 0000:00:1f.2: reg 24: [mem 0x96404000-0x964047ff]
[ 0.625396] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.625401] pci 0000:00:1f.2: PME# disabled
[ 0.625425] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
[ 0.625443] pci 0000:00:1f.3: reg 10: [mem 0x96405000-0x964050ff]
[ 0.625486] pci 0000:00:1f.3: reg 20: [io 0x6000-0x601f]
[ 0.625611] pci 0000:02:00.0: [10ec:8136] type 0 class 0x000200
[ 0.625633] pci 0000:02:00.0: reg 10: [io 0x4000-0x40ff]
[ 0.625672] pci 0000:02:00.0: reg 18: [mem 0x90010000-0x90010fff 64bit pref]
[ 0.625697] pci 0000:02:00.0: reg 20: [mem 0x90000000-0x9000ffff 64bit pref]
[ 0.625765] pci 0000:02:00.0: unsupported PM cap regs version (7)
[ 0.640023] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.640032] pci 0000:00:1c.0: bridge window [io 0x4000-0x5fff]
[ 0.640038] pci 0000:00:1c.0: bridge window [mem 0x95400000-0x963fffff]
[ 0.640047] pci 0000:00:1c.0: bridge window [mem 0x90000000-0x910fffff 64bit pref]
[ 0.640134] pci 0000:03:00.0: [168c:001c] type 0 class 0x000200
[ 0.640166] pci 0000:03:00.0: reg 10: [mem 0x94300000-0x9430ffff 64bit]
[ 0.640316] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.640334] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 0.640341] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
[ 0.640347] pci 0000:00:1c.1: bridge window [mem 0x94300000-0x953fffff]
[ 0.640355] pci 0000:00:1c.1: bridge window [mem 0x91100000-0x920fffff 64bit pref]
[ 0.640419] pci 0000:00:1c.4: PCI bridge to [bus 08-09]
[ 0.640427] pci 0000:00:1c.4: bridge window [io 0x2000-0x2fff]
[ 0.640432] pci 0000:00:1c.4: bridge window [mem 0x93300000-0x942fffff]
[ 0.640441] pci 0000:00:1c.4: bridge window [mem 0x92100000-0x930fffff 64bit pref]
[ 0.640532] pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
[ 0.640541] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.640547] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.640556] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.640559] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.640562] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.640566] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.640569] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[ 0.640599] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.640853] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.640956] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.641027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.641101] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
[ 0.641267] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 0.641282] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.641284] _OSC request data:1 1f 1f
[ 0.646075] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12)
[ 0.646178] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.646273] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.646368] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.646462] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.646558] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.646652] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.646746] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.646796] HEST: Table is not found!
[ 0.646899] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.646920] vgaarb: loaded
[ 0.647143] SCSI subsystem initialized
[ 0.647171] libata version 3.00 loaded.
[ 0.647171] usbcore: registered new interface driver usbfs
[ 0.647171] usbcore: registered new interface driver hub
[ 0.647171] usbcore: registered new device driver usb
[ 0.647171] wmi: Mapper loaded
[ 0.647171] PCI: Using ACPI for IRQ routing
[ 0.647171] PCI: pci_cache_line_size set to 64 bytes
[ 0.647171] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.647171] reserve RAM buffer: 000000007f4de000 - 000000007fffffff
[ 0.647171] reserve RAM buffer: 000000007f543000 - 000000007fffffff
[ 0.647171] reserve RAM buffer: 000000007f5bb000 - 000000007fffffff
[ 0.647171] reserve RAM buffer: 000000007f66a000 - 000000007fffffff
[ 0.647171] NetLabel: Initializing
[ 0.647171] NetLabel: domain hash size = 128
[ 0.647171] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.647171] NetLabel: unlabeled traffic allowed by default
[ 0.647171] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.647171] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.647171] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.660022] Switching to clocksource hpet
[ 0.669670] AppArmor: AppArmor Filesystem Enabled
[ 0.669704] pnp: PnP ACPI init
[ 0.669745] ACPI: bus type pnp registered
[ 0.670692] pnp 00:00: [bus 00-ff]
[ 0.670696] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.670699] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.670701] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.670704] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.670707] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.670710] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.670712] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.670719] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.670722] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.670725] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.670727] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.670730] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.670733] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.670735] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.670738] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.670741] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.670743] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.670746] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[ 0.670833] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.671005] pnp 00:01: [io 0x002e-0x002f]
[ 0.671008] pnp 00:01: [io 0x004e-0x004f]
[ 0.671011] pnp 00:01: [io 0x0068]
[ 0.671013] pnp 00:01: [io 0x006c]
[ 0.671015] pnp 00:01: [io 0x164e-0x164f]
[ 0.671017] pnp 00:01: [io 0x0061]
[ 0.671019] pnp 00:01: [io 0x0070]
[ 0.671022] pnp 00:01: [io 0x0080]
[ 0.671024] pnp 00:01: [io 0x0092]
[ 0.671026] pnp 00:01: [io 0x00b2-0x00b3]
[ 0.671028] pnp 00:01: [io 0x0063]
[ 0.671030] pnp 00:01: [io 0x0065]
[ 0.671032] pnp 00:01: [io 0x0067]
[ 0.671034] pnp 00:01: [io 0x0800-0x080f]
[ 0.671037] pnp 00:01: [io 0x0400-0x047f]
[ 0.671039] pnp 00:01: [io 0x0500-0x053f]
[ 0.671041] pnp 00:01: [mem 0xf8000000-0xfbffffff]
[ 0.671044] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 0.671047] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 0.671049] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 0.671051] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 0.671054] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.671056] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.671170] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.671184] pnp 00:02: [io 0x0000-0x001f]
[ 0.671186] pnp 00:02: [io 0x0081-0x0091]
[ 0.671189] pnp 00:02: [io 0x0093-0x009f]
[ 0.671191] pnp 00:02: [io 0x00c0-0x00df]
[ 0.671194] pnp 00:02: [dma 4]
[ 0.671231] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.671265] pnp 00:03: [io 0x0070-0x0077]
[ 0.671303] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.671411] pnp 00:04: [irq 0 disabled]
[ 0.671428] pnp 00:04: [irq 8]
[ 0.671431] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.671495] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.671509] pnp 00:05: [io 0x00f0]
[ 0.671516] pnp 00:05: [irq 13]
[ 0.671555] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.671569] pnp 00:06: [mem 0xff800000-0xffffffff]
[ 0.671613] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.671634] pnp 00:07: [io 0x0060]
[ 0.671637] pnp 00:07: [io 0x0064]
[ 0.671643] pnp 00:07: [irq 1]
[ 0.671683] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.671717] pnp 00:08: [irq 12]
[ 0.671770] pnp 00:08: Plug and Play ACPI device, IDs SYN1913 SYN1900 SYN0002 PNP0f13 (active)
[ 0.671930] pnp: PnP ACPI: found 9 devices
[ 0.671936] ACPI: ACPI bus type pnp unregistered
[ 0.671954] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.671961] system 00:01: [io 0x0800-0x080f] has been reserved
[ 0.671966] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.671972] system 00:01: [io 0x0500-0x053f] has been reserved
[ 0.671979] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.671985] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.671990] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.671996] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.672007] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.672013] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.672019] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.672030] system 00:04: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.678801] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.678811] pci 0000:00:1c.0: bridge window [io 0x4000-0x5fff]
[ 0.678820] pci 0000:00:1c.0: bridge window [mem 0x95400000-0x963fffff]
[ 0.678829] pci 0000:00:1c.0: bridge window [mem 0x90000000-0x910fffff 64bit pref]
[ 0.678842] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 0.678848] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
[ 0.678857] pci 0000:00:1c.1: bridge window [mem 0x94300000-0x953fffff]
[ 0.678866] pci 0000:00:1c.1: bridge window [mem 0x91100000-0x920fffff 64bit pref]
[ 0.678878] pci 0000:00:1c.4: PCI bridge to [bus 08-09]
[ 0.678884] pci 0000:00:1c.4: bridge window [io 0x2000-0x2fff]
[ 0.678893] pci 0000:00:1c.4: bridge window [mem 0x93300000-0x942fffff]
[ 0.678901] pci 0000:00:1c.4: bridge window [mem 0x92100000-0x930fffff 64bit pref]
[ 0.678913] pci 0000:00:1e.0: PCI bridge to [bus 06-06]
[ 0.678918] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.678927] pci 0000:00:1e.0: bridge window [mem disabled]
[ 0.678934] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.678964] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.678974] pci 0000:00:1c.0: setting latency timer to 64
[ 0.678986] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.678994] pci 0000:00:1c.1: setting latency timer to 64
[ 0.679002] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.679010] pci 0000:00:1c.4: setting latency timer to 64
[ 0.679019] pci 0000:00:1e.0: setting latency timer to 64
[ 0.679024] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.679027] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.679030] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.679033] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
[ 0.679037] pci_bus 0000:02: resource 0 [io 0x4000-0x5fff]
[ 0.679039] pci_bus 0000:02: resource 1 [mem 0x95400000-0x963fffff]
[ 0.679042] pci_bus 0000:02: resource 2 [mem 0x90000000-0x910fffff 64bit pref]
[ 0.679045] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.679048] pci_bus 0000:03: resource 1 [mem 0x94300000-0x953fffff]
[ 0.679051] pci_bus 0000:03: resource 2 [mem 0x91100000-0x920fffff 64bit pref]
[ 0.679054] pci_bus 0000:08: resource 0 [io 0x2000-0x2fff]
[ 0.679057] pci_bus 0000:08: resource 1 [mem 0x93300000-0x942fffff]
[ 0.679060] pci_bus 0000:08: resource 2 [mem 0x92100000-0x930fffff 64bit pref]
[ 0.679063] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7]
[ 0.679065] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff]
[ 0.679068] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.679071] pci_bus 0000:06: resource 7 [mem 0x80000000-0xfebfffff]
[ 0.679121] NET: Registered protocol family 2
[ 0.679269] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.680229] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.683168] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.683890] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.683900] TCP reno registered
[ 0.683927] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.683962] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.684141] NET: Registered protocol family 1
[ 0.684174] pci 0000:00:02.0: Boot video device
[ 0.684463] PCI: CLS 0 bytes, default 64
[ 0.684544] Trying to unpack rootfs image as initramfs...
[ 1.008938] Freeing initrd memory: 12752k freed
[ 1.017976] Simple Boot Flag at 0x44 set to 0x1
[ 1.018288] Scanning for low memory corruption every 60 seconds
[ 1.018463] audit: initializing netlink socket (disabled)
[ 1.018487] type=2000 audit(1300633510.010:1): initialized
[ 1.034055] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.036326] VFS: Disk quotas dquot_6.5.2
[ 1.036406] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.037205] fuse init (API version 7.16)
[ 1.037318] msgmni has been set to 3993
[ 1.037643] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.037654] io scheduler noop registered
[ 1.037658] io scheduler deadline registered
[ 1.037710] io scheduler cfq registered (default)
[ 1.037964] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 1.037981] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.037983] _OSC request data:1 0 1d
[ 1.038079] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 1.038094] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.038096] _OSC request data:1 0 1d
[ 1.038187] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 1.038201] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.038203] _OSC request data:1 0 1d
[ 1.038250] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.038280] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.039297] vesafb: framebuffer at 0x80000000, mapped to 0xffffc90004980000, using 3072k, total 3072k
[ 1.039306] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[ 1.039310] vesafb: scrolling: redraw
[ 1.039315] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.075192] Console: switching to colour frame buffer device 128x48
[ 1.111329] fb0: VESA VGA frame buffer device
[ 1.111642] intel_idle: MWAIT substates: 0x1110
[ 1.111645] intel_idle: does not run on family 6 model 15
[ 1.111839] ACPI: AC Adapter [ADP0] (off-line)
[ 1.112345] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 1.112902] ACPI: Power Button [PWRB]
[ 1.113202] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 1.117538] ACPI: Lid Switch [LID]
[ 1.117837] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.118338] ACPI: Power Button [PWRF]
[ 1.118699] ACPI: Fan [FAN] (on)
[ 1.119069] ACPI: acpi_idle registered with cpuidle
[ 1.119267] Monitor-Mwait will be used to enter C-1 state
[ 1.119305] Monitor-Mwait will be used to enter C-2 state
[ 1.119337] Monitor-Mwait will be used to enter C-3 state
[ 1.119345] Marking TSC unstable due to TSC halts in idle
[ 1.122105] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.122492] ACPI: Thermal Zone [THRM] (61 C)
[ 1.122847] ERST: Table is not found!
[ 1.123738] Linux agpgart interface v0.103
[ 1.124075] ACPI: Battery Slot [BAT0] (battery present)
[ 1.124126] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[ 1.124304] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[ 1.125641] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 1.132332] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
[ 1.132854] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.263525] brd: module loaded
[ 1.264464] loop: module loaded
[ 1.264938] ata_piix 0000:00:1f.1: version 2.13
[ 1.264965] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.280675] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.281094] scsi0 : ata_piix
[ 1.296593] scsi1 : ata_piix
[ 1.311736] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x60e0 irq 14
[ 1.327130] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x60e8 irq 15
[ 1.342809] Fixed MDIO Bus: probed
[ 1.357916] PPP generic driver version 2.4.2
[ 1.372946] tun: Universal TUN/TAP device driver, 1.6
[ 1.387811] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 1.402956] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.418286] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.433856] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.433861] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.449186] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.464504] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.483278] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[ 1.483303] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x96404c00
[ 1.520019] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.534800] ata1.00: ATAPI: TSSTcorp CDDVDW TS-L632H, TO01, max UDMA/33
[ 1.534955] hub 1-0:1.0: USB hub found
[ 1.534961] hub 1-0:1.0: 4 ports detected
[ 1.535071] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.535090] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.535095] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.535161] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 1.620057] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.637639] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 1.637679] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x96404800
[ 1.650255] ata1.00: configured for UDMA/33
[ 1.665388] scsi 0:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L632H TO01 PQ: 0 ANSI: 5
[ 1.680021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.694120] hub 2-0:1.0: USB hub found
[ 1.707739] hub 2-0:1.0: 6 ports detected
[ 1.721143] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.734500] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.747658] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.747760] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.747778] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.747782] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.747854] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 1.800499] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.813911] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.813989] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.850058] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000060c0
[ 1.863491] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 1.863658] hub 3-0:1.0: USB hub found
[ 1.863664] hub 3-0:1.0: 2 ports detected
[ 1.863769] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.863778] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.863782] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.863834] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.945584] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000060a0
[ 1.959339] hub 4-0:1.0: USB hub found
[ 1.972704] hub 4-0:1.0: 2 ports detected
[ 1.986135] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.999713] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.999718] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.013135] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.026928] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00006080
[ 2.040599] hub 5-0:1.0: USB hub found
[ 2.054188] hub 5-0:1.0: 2 ports detected
[ 2.067673] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.081482] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.081486] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.095195] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.110068] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006060
[ 2.124045] hub 6-0:1.0: USB hub found
[ 2.137657] hub 6-0:1.0: 2 ports detected
[ 2.151136] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.164795] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.164800] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.178401] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.194684] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040
[ 2.208550] hub 3-0:1.0: over-current change on port 1
[ 2.208590] hub 7-0:1.0: USB hub found
[ 2.208596] hub 7-0:1.0: 2 ports detected
[ 2.208764] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
[ 2.275833] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.289446] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.303060] mousedev: PS/2 mouse device common for all mice
[ 2.316772] rtc_cmos 00:03: RTC can wake from S4
[ 2.330416] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.344033] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 2.357688] device-mapper: uevent: version 1.0.3
[ 2.371032] hub 6-0:1.0: over-current change on port 2
[ 2.371185] device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@xxxxxxxxxx
[ 2.371259] device-mapper: multipath: version 1.1.1 loaded
[ 2.371262] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.371500] cpuidle: using governor ladder
[ 2.439337] cpuidle: using governor menu
[ 2.452811] TCP cubic registered
[ 2.465982] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.466056] NET: Registered protocol family 10
[ 2.466448] lo: Disabled Privacy Extensions
[ 2.466689] NET: Registered protocol family 17
[ 2.466718] Registering the dns_resolver key type
[ 2.533888] PM: Hibernation image not present or could not be loaded.
[ 2.533905] registered taskstats version 1
[ 2.547320] Magic number: 3:587:83
[ 2.561404] rtc_cmos 00:03: setting system clock to 2011-03-20 15:05:13 UTC (1300633513)
[ 2.574879] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.588404] EDD information not available.
[ 2.604532] Freeing unused kernel memory: 932k freed
[ 2.618447] Write protecting the kernel read-only data: 10240k
[ 2.633930] Freeing unused kernel memory: 324k freed
[ 2.655699] Freeing unused kernel memory: 1564k freed
[ 2.708027] udev[75]: starting version 167
[ 2.860329] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.860360] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.860420] r8169 0000:02:00.0: setting latency timer to 64
[ 2.860499] r8169 0000:02:00.0: irq 40 for MSI/MSI-X
[ 2.861105] r8169 0000:02:00.0: eth0: RTL8102e at 0xffffc90000332000, 00:1e:33:3b:3a:29, XID 14a00000 IRQ 40
[ 2.906477] ahci 0000:00:1f.2: version 3.0
[ 2.906501] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.906579] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 2.906629] ahci: SSS flag set, parallel bus scan disabled
[ 2.906665] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x3 impl SATA mode
[ 2.906669] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ccc ems
[ 2.906675] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.967317] scsi2 : ahci
[ 2.983045] scsi3 : ahci
[ 2.983196] scsi4 : ahci
[ 2.983350] ata3: SATA max UDMA/133 abar m2048@0x96404000 port 0x96404100 irq 41
[ 2.983355] ata4: SATA max UDMA/133 abar m2048@0x96404000 port 0x96404180 irq 41
[ 2.983357] ata5: DUMMY
[ 3.770067] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.168275] ata3.00: ATA-8: TOSHIBA MK1246GSX, LB213M, max UDMA/100
[ 4.182952] ata3.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.198916] ata3.00: configured for UDMA/100
[ 4.213961] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1246GS LB21 PQ: 0 ANSI: 5
[ 4.229515] sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 4.229553] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 4.260183] sd 2:0:0:0: [sda] Write Protect is off
[ 4.275231] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.275263] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.369904] sda: sda1 sda2 sda3
[ 4.385295] sd 2:0:0:0: [sda] Attached SCSI disk
[ 4.590092] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.096868] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 14.256248] Adding 1550268k swap on /dev/sda3. Priority:-1 extents:1 across:1550268k
[ 14.322326] udev[289]: starting version 167
[ 14.487278] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.597853] lp: driver loaded but no devices found
[ 14.764093] Linux video capture interface: v2.00
[ 14.799452] uvcvideo: Found UVC 1.00 device CNF7051 (04f2:b070)
[ 14.816300] input: CNF7051 as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input4
[ 14.816390] usbcore: registered new interface driver uvcvideo
[ 14.816393] USB Video Class driver (v1.0.0)
[ 14.950567] cfg80211: Calling CRDA to update world regulatory domain
[ 15.000322] cfg80211: World regulatory domain updated:
[ 15.000326] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.000330] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.000334] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.000337] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.000340] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.000343] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.191790] [drm] Initialized drm 1.1.0 20060810
[ 15.414108] type=1400 audit(1300633526.348:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=541 comm="apparmor_parser"
[ 15.414202] type=1400 audit(1300633526.348:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=541 comm="apparmor_parser"
[ 15.414272] type=1400 audit(1300633526.348:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=541 comm="apparmor_parser"
[ 15.530490] type=1400 audit(1300633526.468:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=522 comm="apparmor_parser"
[ 15.530586] type=1400 audit(1300633526.468:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=522 comm="apparmor_parser"
[ 15.531766] type=1400 audit(1300633526.468:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=522 comm="apparmor_parser"
[ 15.579090] ath5k 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 15.579108] ath5k 0000:03:00.0: setting latency timer to 64
[ 15.579271] ath5k 0000:03:00.0: registered as 'phy0'
[ 15.589398] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.589405] i915 0000:00:02.0: setting latency timer to 64
[ 16.052824] i915 0000:00:02.0: irq 42 for MSI/MSI-X
[ 16.108419] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 16.108741] [drm] initialized overlay support
[ 16.147089] ath: EEPROM regdomain: 0x69
[ 16.147093] ath: EEPROM indicates we should expect a direct regpair map
[ 16.147098] ath: Country alpha2 being used: 00
[ 16.147100] ath: Regpair used: 0x69
[ 16.147104] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147107] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147110] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147114] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147116] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147120] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147122] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147126] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147128] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147132] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147134] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147137] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147140] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147143] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147146] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147149] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147152] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147155] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147158] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147161] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147164] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147167] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 16.147170] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel
[ 16.147172] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel
[ 16.147175] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
[ 16.147178] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147181] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147184] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147187] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147190] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147193] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147196] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147199] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147202] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147205] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147208] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147211] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147213] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147217] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147219] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147223] cfg80211: 5140000 KHz - 5360000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147225] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147229] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147231] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147235] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147237] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147241] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147243] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147247] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147249] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147253] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147255] cfg80211: Updating information on frequency 5600 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147259] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147261] cfg80211: Updating information on frequency 5620 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147264] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147267] cfg80211: Updating information on frequency 5640 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147270] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147273] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147276] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147279] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147282] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147285] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147288] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147291] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147294] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147297] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147300] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147303] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147306] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147308] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147312] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147314] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule:
[ 16.147318] cfg80211: 5460000 KHz - 5860000 KHz @ KHz), (N/A mBi, 3000 mBm)
[ 16.147424] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 16.233540] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x9280b1, caps: 0xa04711/0xa04000/0x0
[ 16.292175] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 16.292912] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa2, PHY: 0x61)
[ 16.311087] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[ 16.486380] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 16.519738] checking generic (80000000 300000) vs hw (80000000 10000000)
[ 16.519743] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 16.519858] Console: switching to colour dummy device 80x25
[ 16.540106] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is zero.
[ 16.540130] Console: switching to colour frame buffer device 180x56
[ 16.544344] fb0: inteldrmfb frame buffer device
[ 16.544347] drm: registered panic notifier
[ 16.556358] acpi device:19: registered as cooling_device3
[ 16.557941] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 16.558220] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 16.558997] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 16.559092] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 16.559177] HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 16.559222] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 16.688707] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 16.772472] hda_codec: ALC268: BIOS auto-probing.
[ 16.778226] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 16.778329] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 17.092229] ppdev: user-space parallel port driver
[ 17.207954] r8169 0000:02:00.0: eth0: link down
[ 17.208319] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.217339] type=1400 audit(1300633528.148:8): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=802 comm="apparmor_parser"
[ 17.260700] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 17.857136] type=1400 audit(1300633528.788:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=803 comm="apparmor_parser"
[ 17.857235] type=1400 audit(1300633528.788:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=803 comm="apparmor_parser"
[ 17.857306] type=1400 audit(1300633528.788:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=803 comm="apparmor_parser"
[ 25.554763] audit_printk_skb: 18 callbacks suppressed
[ 25.554767] type=1400 audit(1300633536.488:18): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=842 comm="apparmor_parser"
[ 25.555779] type=1400 audit(1300633536.488:19): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=842 comm="apparmor_parser"
[ 25.556397] type=1400 audit(1300633536.488:20): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=842 comm="apparmor_parser"
[ 90.410053] usb 6-1: new full speed USB device using uhci_hcd and address 2
[ 90.540060] usb 6-1: device descriptor read/64, error -71
[ 90.780070] usb 6-1: device descriptor read/64, error -71
[ 91.010047] usb 6-1: new full speed USB device using uhci_hcd and address 3
[ 91.140045] usb 6-1: device descriptor read/64, error -71
[ 91.380070] usb 6-1: device descriptor read/64, error -71
[ 91.610078] usb 6-1: new full speed USB device using uhci_hcd and address 4
[ 92.030046] usb 6-1: device not accepting address 4, error -71
[ 92.150071] usb 6-1: new full speed USB device using uhci_hcd and address 5
[ 92.570068] usb 6-1: device not accepting address 5, error -71
[ 92.570122] hub 6-0:1.0: unable to enumerate USB device on port 1
[ 119.380080] usb 2-3: new high speed USB device using ehci_hcd and address 3
[ 119.952000] usbcore: registered new interface driver uas
[ 119.973284] Initializing USB Mass Storage driver...
[ 119.973361] usb-storage: USB Mass Storage device detected
[ 119.973436] usb-storage: -- associate_dev
[ 119.973439] usb-storage: Vendor: 0x0644, Product: 0x800d, Revision: 0x0150
[ 119.973441] usb-storage: Interface Subclass: 0x06, Protocol: 0x50
[ 119.973449] usb-storage: Transport: Bulk
[ 119.973451] usb-storage: Protocol: Transparent SCSI
[ 119.973486] scsi5 : usb-storage 2-3:1.0
[ 119.973604] usb-storage: *** thread sleeping.
[ 119.973636] usbcore: registered new interface driver usb-storage
[ 119.973638] USB Mass Storage support registered.
[ 119.974628] usb-storage 2-3:1.0: device found
[ 119.974633] usb-storage 2-3:1.0: waiting for device to settle before scanning
[ 120.970065] usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
[ 120.970714] usb-storage: GetMaxLUN command result is -32, data is 0
[ 120.970797] usb-storage 2-3:1.0: scan complete
[ 120.970876] usb-storage: queuecommand_lck called
[ 120.970897] usb-storage: *** thread awakened.
[ 120.970900] usb-storage: Command INQUIRY (6 bytes)
[ 120.970902] usb-storage: 12 00 00 00 24 00
[ 120.970910] usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
[ 120.970913] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 120.971206] usb-storage: Status code 0; transferred 31/31
[ 120.971209] usb-storage: -- transfer complete
[ 120.971211] usb-storage: Bulk command transfer result=0
[ 120.971213] usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
[ 120.973080] usb-storage: Status code 0; transferred 36/36
[ 120.973082] usb-storage: -- transfer complete
[ 120.973084] usb-storage: Bulk data transfer result 0x0
[ 120.973086] usb-storage: Attempting to get CSW...
[ 120.973088] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.973329] usb-storage: Status code 0; transferred 13/13
[ 120.973331] usb-storage: -- transfer complete
[ 120.973333] usb-storage: Bulk status result = 0
[ 120.973336] usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
[ 120.973338] usb-storage: scsi cmd done, result=0x0
[ 120.973343] usb-storage: *** thread sleeping.
[ 120.973388] scsi 5:0:0:0: Direct-Access USB-HS SAMSUNG SP0411N 0.01 PQ: 0 ANSI: 0
[ 120.973428] usb-storage: queuecommand_lck called
[ 120.973447] usb-storage: *** thread awakened.
[ 120.973450] usb-storage: Bad LUN (0:1)
[ 120.973452] usb-storage: scsi cmd done, result=0x40000
[ 120.973455] usb-storage: *** thread sleeping.
[ 120.973520] usb-storage: queuecommand_lck called
[ 120.973538] usb-storage: *** thread awakened.
[ 120.973541] usb-storage: Bad target number (1:0)
[ 120.973543] usb-storage: scsi cmd done, result=0x40000
[ 120.973546] usb-storage: *** thread sleeping.
[ 120.973599] usb-storage: queuecommand_lck called
[ 120.973617] usb-storage: *** thread awakened.
[ 120.973620] usb-storage: Bad target number (2:0)
[ 120.973622] usb-storage: scsi cmd done, result=0x40000
[ 120.973625] usb-storage: *** thread sleeping.
[ 120.973676] usb-storage: queuecommand_lck called
[ 120.973694] usb-storage: *** thread awakened.
[ 120.973697] usb-storage: Bad target number (3:0)
[ 120.973699] usb-storage: scsi cmd done, result=0x40000
[ 120.973702] usb-storage: *** thread sleeping.
[ 120.973753] usb-storage: queuecommand_lck called
[ 120.973771] usb-storage: *** thread awakened.
[ 120.973773] usb-storage: Bad target number (4:0)
[ 120.973775] usb-storage: scsi cmd done, result=0x40000
[ 120.973778] usb-storage: *** thread sleeping.
[ 120.973829] usb-storage: queuecommand_lck called
[ 120.973846] usb-storage: *** thread awakened.
[ 120.973848] usb-storage: Bad target number (5:0)
[ 120.973850] usb-storage: scsi cmd done, result=0x40000
[ 120.973854] usb-storage: *** thread sleeping.
[ 120.973906] usb-storage: queuecommand_lck called
[ 120.973923] usb-storage: *** thread awakened.
[ 120.973925] usb-storage: Bad target number (6:0)
[ 120.973927] usb-storage: scsi cmd done, result=0x40000
[ 120.973931] usb-storage: *** thread sleeping.
[ 120.973983] usb-storage: queuecommand_lck called
[ 120.973999] usb-storage: *** thread awakened.
[ 120.974002] usb-storage: Bad target number (7:0)
[ 120.974004] usb-storage: scsi cmd done, result=0x40000
[ 120.974007] usb-storage: *** thread sleeping.
[ 120.974188] usb-storage: queuecommand_lck called
[ 120.974196] usb-storage: *** thread awakened.
[ 120.974199] usb-storage: Command TEST_UNIT_READY (6 bytes)
[ 120.974201] usb-storage: 00 00 00 00 00 00
[ 120.974208] usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
[ 120.974211] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 120.974348] usb-storage: Status code 0; transferred 31/31
[ 120.974351] usb-storage: -- transfer complete
[ 120.974353] usb-storage: Bulk command transfer result=0
[ 120.974355] usb-storage: Attempting to get CSW...
[ 120.974358] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.974457] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 120.974702] usb-storage: Status code 0; transferred 13/13
[ 120.974704] usb-storage: -- transfer complete
[ 120.974707] usb-storage: Bulk status result = 0
[ 120.974710] usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
[ 120.974713] usb-storage: scsi cmd done, result=0x0
[ 120.974719] usb-storage: *** thread sleeping.
[ 120.974753] usb-storage: queuecommand_lck called
[ 120.974758] usb-storage: *** thread awakened.
[ 120.974760] usb-storage: Command READ_CAPACITY (10 bytes)
[ 120.974762] usb-storage: 25 00 00 00 00 00 00 00 00 00
[ 120.974771] usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10
[ 120.974774] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 120.974831] usb-storage: Status code 0; transferred 31/31
[ 120.974833] usb-storage: -- transfer complete
[ 120.974835] usb-storage: Bulk command transfer result=0
[ 120.974838] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
[ 120.975586] usb-storage: Status code 0; transferred 8/8
[ 120.975589] usb-storage: -- transfer complete
[ 120.975592] usb-storage: Bulk data transfer result 0x0
[ 120.975594] usb-storage: Attempting to get CSW...
[ 120.975596] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.977197] usb-storage: Status code 0; transferred 13/13
[ 120.977201] usb-storage: -- transfer complete
[ 120.977204] usb-storage: Bulk status result = 0
[ 120.977206] usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
[ 120.977211] usb-storage: scsi cmd done, result=0x0
[ 120.977216] usb-storage: *** thread sleeping.
[ 120.977256] sd 5:0:0:0: [sdb] 78242976 512-byte logical blocks: (40.0 GB/37.3 GiB)
[ 120.977283] usb-storage: queuecommand_lck called
[ 120.977289] usb-storage: *** thread awakened.
[ 120.977292] usb-storage: Command MODE_SENSE (6 bytes)
[ 120.977294] usb-storage: 1a 00 3f 00 c0 00
[ 120.977302] usb-storage: Bulk Command S 0x43425355 T 0x4 L 192 F 128 Trg 0 LUN 0 CL 6
[ 120.977305] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 120.977455] usb-storage: Status code 0; transferred 31/31
[ 120.977458] usb-storage: -- transfer complete
[ 120.977460] usb-storage: Bulk command transfer result=0
[ 120.977463] usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
[ 120.978082] usb-storage: Status code -121; transferred 12/192
[ 120.978086] usb-storage: -- short read transfer
[ 120.978089] usb-storage: Bulk data transfer result 0x1
[ 120.978091] usb-storage: Attempting to get CSW...
[ 120.978093] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.978586] usb-storage: Status code -32; transferred 0/13
[ 120.978591] usb-storage: clearing endpoint halt for pipe 0xc0010380
[ 120.978594] usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
[ 120.978708] usb-storage: usb_stor_clear_halt: result = 0
[ 120.978710] usb-storage: Attempting to get CSW (2nd try)...
[ 120.978713] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.978827] usb-storage: Status code 0; transferred 13/13
[ 120.978830] usb-storage: -- transfer complete
[ 120.978832] usb-storage: Bulk status result = 0
[ 120.978834] usb-storage: Bulk Status S 0x53425355 T 0x4 R 180 Stat 0x0
[ 120.978838] usb-storage: scsi cmd done, result=0x0
[ 120.978844] usb-storage: *** thread sleeping.
[ 120.978876] sd 5:0:0:0: [sdb] Write Protect is off
[ 120.978880] sd 5:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 120.978903] usb-storage: queuecommand_lck called
[ 120.978910] usb-storage: *** thread awakened.
[ 120.978913] usb-storage: Command MODE_SENSE (6 bytes)
[ 120.978915] usb-storage: 1a 00 3f 00 04 00
[ 120.978922] usb-storage: Bulk Command S 0x43425355 T 0x5 L 4 F 128 Trg 0 LUN 0 CL 6
[ 120.978925] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 120.979208] usb-storage: Status code 0; transferred 31/31
[ 120.979210] usb-storage: -- transfer complete
[ 120.979212] usb-storage: Bulk command transfer result=0
[ 120.979215] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4 bytes, 1 entries
[ 120.979961] usb-storage: Status code -75; transferred 0/4
[ 120.979964] usb-storage: -- babble
[ 120.979966] usb-storage: Bulk data transfer result 0x3
[ 120.979968] usb-storage: Attempting to get CSW...
[ 120.979970] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 120.980203] usb-storage: Status code 0; transferred 12/13
[ 120.980205] usb-storage: -- short transfer
[ 120.980208] usb-storage: Bulk status result = 1
[ 120.980210] usb-storage: -- transport indicates error, resetting
[ 120.980217] usb-storage: usb_stor_pre_reset
[ 121.120090] usb 2-3: reset high speed USB device using ehci_hcd and address 3
[ 136.240062] usb 2-3: device descriptor read/64, error -110
[ 151.060049] usb-storage: command_abort called
[ 151.470063] usb 2-3: device descriptor read/64, error -110
[ 151.700061] usb 2-3: reset high speed USB device using ehci_hcd and address 3
[ 166.820044] usb 2-3: device descriptor read/64, error -110
[ 170.270332] usb-storage: usb_stor_post_reset
[ 170.270338] usb-storage: usb_reset_device returns -19
[ 170.270343] usb-storage: usb_stor_Bulk_reset called
[ 170.270347] usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
[ 170.270351] usb-storage: Soft reset failed: -19
[ 170.270354] usb-storage: scsi cmd done, result=0x70000
[ 170.270360] usb-storage: *** thread sleeping.
[ 170.270367] usb-storage: queuecommand_lck called
[ 170.270371] usb-storage: *** thread awakened.
[ 170.270374] usb-storage: Command TEST_UNIT_READY (6 bytes)
[ 170.270376] usb-storage: 00 00 00 00 00 00
[ 170.270384] usb-storage: Bulk Command S 0x43425355 T 0x6 L 0 F 0 Trg 0 LUN 0 CL 6
[ 170.270387] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 170.270390] usb-storage: Status code -19; transferred 12/31
[ 170.270392] usb-storage: -- unknown error
[ 170.270394] usb-storage: Bulk command transfer result=4
[ 170.270396] usb-storage: -- transport indicates error, resetting
[ 170.270398] usb-storage: unable to lock device for reset: -19
[ 170.270400] usb-storage: usb_stor_Bulk_reset called
[ 170.270403] usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
[ 170.270406] usb-storage: Soft reset failed: -19
[ 170.270408] usb-storage: scsi cmd done, result=0x70000
[ 170.270411] usb-storage: *** thread sleeping.
[ 170.270417] usb-storage: device_reset called
[ 170.270419] usb-storage: usb_stor_Bulk_reset called
[ 170.270422] usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
[ 170.270425] usb-storage: Soft reset failed: -19
[ 170.270428] usb-storage: bus_reset called
[ 170.270430] usb-storage: unable to lock device for reset: -19
[ 170.270434] sd 5:0:0:0: Device offlined - not ready after error recovery
[ 170.270466] sd 5:0:0:0: [sdb] Asking for cache data failed
[ 170.270473] usb 2-3: USB disconnect, address 3
[ 170.270547] usb-storage: storage_disconnect() called
[ 170.272587] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 170.274850] usb-storage: queuecommand_lck called
[ 170.274855] usb-storage: Fail command during disconnect
[ 170.274890] usb-storage: queuecommand_lck called
[ 170.274893] usb-storage: Fail command during disconnect
[ 170.274909] usb-storage: queuecommand_lck called
[ 170.274911] usb-storage: Fail command during disconnect
[ 170.274925] usb-storage: queuecommand_lck called
[ 170.274927] usb-storage: Fail command during disconnect
[ 170.274937] sd 5:0:0:0: [sdb] READ CAPACITY failed
[ 170.274940] sd 5:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 170.274945] sd 5:0:0:0: [sdb] Sense not available.
[ 170.274953] usb-storage: queuecommand_lck called
[ 170.274955] usb-storage: Fail command during disconnect
[ 170.274969] usb-storage: queuecommand_lck called
[ 170.274971] usb-storage: Fail command during disconnect
[ 170.274981] sd 5:0:0:0: [sdb] Asking for cache data failed
[ 170.276923] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 170.278752] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 170.292433] usb-storage: -- usb_stor_release_resources
[ 170.292437] usb-storage: -- sending exit command to thread
[ 170.292445] usb-storage: *** thread awakened.
[ 170.292447] usb-storage: -- exiting
[ 170.292474] usb-storage: -- dissociate_dev
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.37-custom13+ (root@calder) (gcc version 4.5.2 (Ubuntu/Linaro 4.5.2-6ubuntu4) ) #14 SMP Fri Mar 18 23:15:07 GMT 2011
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.37-custom13+ root=UUID=51e6266e-2230-442b-8cfa-3708c9a6a51b ro single
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f4de000 (usable)
[ 0.000000] BIOS-e820: 000000007f4de000 - 000000007f4e9000 (reserved)
[ 0.000000] BIOS-e820: 000000007f4e9000 - 000000007f543000 (usable)
[ 0.000000] BIOS-e820: 000000007f543000 - 000000007f546000 (reserved)
[ 0.000000] BIOS-e820: 000000007f546000 - 000000007f5bb000 (usable)
[ 0.000000] BIOS-e820: 000000007f5bb000 - 000000007f5bf000 (reserved)
[ 0.000000] BIOS-e820: 000000007f5bf000 - 000000007f66a000 (usable)
[ 0.000000] BIOS-e820: 000000007f66a000 - 000000007f6bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f6bf000 - 000000007f700000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007f700000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.4 present.
[ 0.000000] DMI: Base Board Product Name/EQUIUM L350, BIOS 1.30 03/19/2008
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7f66a max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFFE0000 mask FFFFE0000 write-protect
[ 0.000000] 1 base 000000000 mask FC0000000 write-back
[ 0.000000] 2 base 040000000 mask FC0000000 write-back
[ 0.000000] 3 base 07F800000 mask FFF800000 uncachable
[ 0.000000] 4 base 07F700000 mask FFFF00000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [ffff8800000fe230] fe230
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f66a000
[ 0.000000] 0000000000 - 007f600000 page 2M
[ 0.000000] 007f600000 - 007f66a000 page 4k
[ 0.000000] kernel direct mapping tables up to 7f66a000 @ 1fffc000-20000000
[ 0.000000] RAMDISK: 3672c000 - 3738e000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 TOSINV)
[ 0.000000] ACPI: XSDT 000000007f6fe120 00064 (v01 TOSINV TOSINV00 00000001 01000013)
[ 0.000000] ACPI: FACP 000000007f6fd000 000F4 (v04 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: DSDT 000000007f6f5000 078BB (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: FACS 000000007f675000 00040
[ 0.000000] ACPI: APIC 000000007f6f4000 00068 (v02 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: HPET 000000007f6f3000 00038 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: MCFG 000000007f6f2000 0003C (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: ASF! 000000007f6f1000 000A5 (v32 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: SLIC 000000007f6f0000 00176 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: BOOT 000000007f6ef000 00028 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 000000007f6ee000 004C4 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f66a000
[ 0.000000] Initmem setup node 0 0000000000000000-000000007f66a000
[ 0.000000] NODE_DATA [000000007f4d9000 - 000000007f4ddfff]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff88007cc00000-ffff88007e7fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[5] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007f4de
[ 0.000000] 0: 0x0007f4e9 -> 0x0007f543
[ 0.000000] 0: 0x0007f546 -> 0x0007f5bb
[ 0.000000] 0: 0x0007f5bf -> 0x0007f66a
[ 0.000000] On node 0 totalpages: 521703
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3921 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7079 pages used for memmap
[ 0.000000] DMA32 zone: 510641 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007f4de000 - 000000007f4e9000
[ 0.000000] PM: Registered nosave memory: 000000007f543000 - 000000007f546000
[ 0.000000] PM: Registered nosave memory: 000000007f5bb000 - 000000007f5bf000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007f200000 s83648 r8192 d22848 u1048576
[ 0.000000] pcpu-alloc: s83648 r8192 d22848 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 514562
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.37-custom13+ root=UUID=51e6266e-2230-442b-8cfa-3708c9a6a51b ro single
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2032000k/2087336k available (5774k kernel code, 524k absent, 54812k reserved, 5146k data, 916k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:512 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 20971520 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1729.331 MHz processor.
[ 0.010015] Calibrating delay loop (skipped), value calculated using timer frequency.. 3458.66 BogoMIPS (lpj=17293310)
[ 0.010026] pid_max: default: 32768 minimum: 301
[ 0.010056] Security Framework initialized
[ 0.010074] AppArmor: AppArmor initialized
[ 0.010429] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.011975] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.012719] Mount-cache hash table entries: 256
[ 0.012931] Initializing cgroup subsys ns
[ 0.012945] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.012953] Initializing cgroup subsys cpuacct
[ 0.012961] Initializing cgroup subsys memory
[ 0.012974] Initializing cgroup subsys devices
[ 0.012980] Initializing cgroup subsys freezer
[ 0.012985] Initializing cgroup subsys net_cls
[ 0.012989] Initializing cgroup subsys blkio
[ 0.013043] CPU: Physical Processor ID: 0
[ 0.013048] CPU: Processor Core ID: 0
[ 0.013053] mce: CPU supports 6 MCE banks
[ 0.013064] CPU0: Thermal monitoring handled by SMI
[ 0.013070] using mwait in idle threads.
[ 0.013074] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.013085] PEBS disabled due to CPU errata.
[ 0.013093] ... version: 2
[ 0.013097] ... bit width: 40
[ 0.013101] ... generic registers: 2
[ 0.013105] ... value mask: 000000ffffffffff
[ 0.013110] ... max period: 000000007fffffff
[ 0.013114] ... fixed-purpose events: 3
[ 0.013118] ... event mask: 0000000700000003
[ 0.020142] ACPI: Core revision 20101013
[ 0.040015] ftrace: allocating 22428 entries in 88 pages
[ 0.050081] Setting APIC routing to flat
[ 0.050439] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.153573] CPU0: Intel(R) Pentium(R) Dual CPU T2370 @ 1.73GHz stepping 0d
[ 0.160000] Booting Node 0, Processors #1 Ok.
[ 0.020000] CPU1: Thermal monitoring handled by SMI
[ 0.320021] Brought up 2 CPUs
[ 0.320029] Total of 2 processors activated (6917.08 BogoMIPS).
[ 0.320464] devtmpfs: initialized
[ 0.320975] regulator: core version 0.5
[ 0.321033] regulator: dummy:
[ 0.321062] Time: 14:58:48 Date: 03/20/11
[ 0.321115] NET: Registered protocol family 16
[ 0.321264] ACPI: bus type pci registered
[ 0.321362] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.321371] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.338453] PCI: Using configuration type 1 for base access
[ 0.339343] bio: create slab <bio-0> at 0
[ 0.341670] ACPI: EC: Look up EC in DSDT
[ 0.343817] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.345344] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.346131] ACPI: SSDT 000000007f674c90 00232 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.346636] ACPI: Dynamic OEM Table Load:
[ 0.346643] ACPI: SSDT (null) 00232 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.346980] ACPI: SSDT 000000007f673610 005B3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.347457] ACPI: Dynamic OEM Table Load:
[ 0.347464] ACPI: SSDT (null) 005B3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.380397] ACPI: SSDT 000000007f674f10 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.380887] ACPI: Dynamic OEM Table Load:
[ 0.380894] ACPI: SSDT (null) 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.381064] ACPI: SSDT 000000007f676d10 00083 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.381543] ACPI: Dynamic OEM Table Load:
[ 0.381550] ACPI: SSDT (null) 00083 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.420334] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 0.560073] ACPI: Interpreter enabled
[ 0.560080] ACPI: (supports S0 S3 S4 S5)
[ 0.560115] ACPI: Using IOAPIC for interrupt routing
[ 0.570889] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.572959] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.573111] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.574320] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-723)
[ 0.581081] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.581140] ACPI: Power Resource [FN00] (on)
[ 0.581334] ACPI: No dock devices found.
[ 0.581341] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.582003] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 0.582019] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.582021] _OSC request data:1 8 1f
[ 0.582027] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.583183] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.583191] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.583197] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.583205] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
[ 0.583226] pci 0000:00:00.0: [8086:2a00] type 0 class 0x000600
[ 0.583288] pci 0000:00:02.0: [8086:2a02] type 0 class 0x000300
[ 0.583306] pci 0000:00:02.0: reg 10: [mem 0x93100000-0x931fffff 64bit]
[ 0.583318] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
[ 0.583327] pci 0000:00:02.0: reg 20: [io 0x6110-0x6117]
[ 0.583372] pci 0000:00:02.1: [8086:2a03] type 0 class 0x000380
[ 0.583388] pci 0000:00:02.1: reg 10: [mem 0x93200000-0x932fffff 64bit]
[ 0.583489] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
[ 0.583551] pci 0000:00:1a.0: reg 20: [io 0x60c0-0x60df]
[ 0.583599] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
[ 0.583660] pci 0000:00:1a.1: reg 20: [io 0x60a0-0x60bf]
[ 0.583722] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
[ 0.583750] pci 0000:00:1a.7: reg 10: [mem 0x96404c00-0x96404fff]
[ 0.583855] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.583861] pci 0000:00:1a.7: PME# disabled
[ 0.583894] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
[ 0.583917] pci 0000:00:1b.0: reg 10: [mem 0x96400000-0x96403fff 64bit]
[ 0.584004] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.584009] pci 0000:00:1b.0: PME# disabled
[ 0.584039] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
[ 0.584128] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.584134] pci 0000:00:1c.0: PME# disabled
[ 0.584166] pci 0000:00:1c.1: [8086:2841] type 1 class 0x000604
[ 0.584254] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.584260] pci 0000:00:1c.1: PME# disabled
[ 0.584296] pci 0000:00:1c.4: [8086:2847] type 1 class 0x000604
[ 0.584385] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.584390] pci 0000:00:1c.4: PME# disabled
[ 0.584424] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
[ 0.584485] pci 0000:00:1d.0: reg 20: [io 0x6080-0x609f]
[ 0.584530] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
[ 0.584591] pci 0000:00:1d.1: reg 20: [io 0x6060-0x607f]
[ 0.584639] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
[ 0.584700] pci 0000:00:1d.2: reg 20: [io 0x6040-0x605f]
[ 0.584760] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
[ 0.584788] pci 0000:00:1d.7: reg 10: [mem 0x96404800-0x96404bff]
[ 0.584892] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.584898] pci 0000:00:1d.7: PME# disabled
[ 0.584924] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.585012] pci 0000:00:1f.0: [8086:2815] type 0 class 0x000601
[ 0.585122] pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.585132] pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO
[ 0.585142] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f)
[ 0.585150] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0007)
[ 0.585198] pci 0000:00:1f.1: [8086:2850] type 0 class 0x000101
[ 0.585217] pci 0000:00:1f.1: reg 10: [io 0x6108-0x610f]
[ 0.585231] pci 0000:00:1f.1: reg 14: [io 0x6124-0x6127]
[ 0.585245] pci 0000:00:1f.1: reg 18: [io 0x6100-0x6107]
[ 0.585258] pci 0000:00:1f.1: reg 1c: [io 0x6120-0x6123]
[ 0.585272] pci 0000:00:1f.1: reg 20: [io 0x60e0-0x60ef]
[ 0.585329] pci 0000:00:1f.2: [8086:2829] type 0 class 0x000106
[ 0.585356] pci 0000:00:1f.2: reg 10: [io 0x60f8-0x60ff]
[ 0.585369] pci 0000:00:1f.2: reg 14: [io 0x611c-0x611f]
[ 0.585382] pci 0000:00:1f.2: reg 18: [io 0x60f0-0x60f7]
[ 0.585395] pci 0000:00:1f.2: reg 1c: [io 0x6118-0x611b]
[ 0.585407] pci 0000:00:1f.2: reg 20: [io 0x6020-0x603f]
[ 0.585420] pci 0000:00:1f.2: reg 24: [mem 0x96404000-0x964047ff]
[ 0.585468] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.585474] pci 0000:00:1f.2: PME# disabled
[ 0.585498] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
[ 0.585516] pci 0000:00:1f.3: reg 10: [mem 0x96405000-0x964050ff]
[ 0.585560] pci 0000:00:1f.3: reg 20: [io 0x6000-0x601f]
[ 0.585685] pci 0000:02:00.0: [10ec:8136] type 0 class 0x000200
[ 0.585708] pci 0000:02:00.0: reg 10: [io 0x4000-0x40ff]
[ 0.585747] pci 0000:02:00.0: reg 18: [mem 0x90010000-0x90010fff 64bit pref]
[ 0.585772] pci 0000:02:00.0: reg 20: [mem 0x90000000-0x9000ffff 64bit pref]
[ 0.585841] pci 0000:02:00.0: unsupported PM cap regs version (7)
[ 0.600024] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.600033] pci 0000:00:1c.0: bridge window [io 0x4000-0x5fff]
[ 0.600039] pci 0000:00:1c.0: bridge window [mem 0x95400000-0x963fffff]
[ 0.600048] pci 0000:00:1c.0: bridge window [mem 0x90000000-0x910fffff 64bit pref]
[ 0.600139] pci 0000:03:00.0: [168c:001c] type 0 class 0x000200
[ 0.600170] pci 0000:03:00.0: reg 10: [mem 0x94300000-0x9430ffff 64bit]
[ 0.600320] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.600338] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 0.600346] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
[ 0.600352] pci 0000:00:1c.1: bridge window [mem 0x94300000-0x953fffff]
[ 0.600361] pci 0000:00:1c.1: bridge window [mem 0x91100000-0x920fffff 64bit pref]
[ 0.600424] pci 0000:00:1c.4: PCI bridge to [bus 08-09]
[ 0.600432] pci 0000:00:1c.4: bridge window [io 0x2000-0x2fff]
[ 0.600438] pci 0000:00:1c.4: bridge window [mem 0x93300000-0x942fffff]
[ 0.600447] pci 0000:00:1c.4: bridge window [mem 0x92100000-0x930fffff 64bit pref]
[ 0.600540] pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
[ 0.600549] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.600555] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.600564] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.600567] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.600571] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.600574] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.600577] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[ 0.600608] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.600865] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.600969] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.601040] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.601116] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
[ 0.601282] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 0.601297] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.601299] _OSC request data:1 1f 1f
[ 0.606046] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12)
[ 0.606150] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.606248] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.606343] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.606438] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.606536] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.606631] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.606726] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.606777] HEST: Table is not found!
[ 0.606875] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.606897] vgaarb: loaded
[ 0.607124] SCSI subsystem initialized
[ 0.607147] libata version 3.00 loaded.
[ 0.607147] usbcore: registered new interface driver usbfs
[ 0.607147] usbcore: registered new interface driver hub
[ 0.607147] usbcore: registered new device driver usb
[ 0.607147] wmi: Mapper loaded
[ 0.607147] PCI: Using ACPI for IRQ routing
[ 0.607147] PCI: pci_cache_line_size set to 64 bytes
[ 0.607147] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.607147] reserve RAM buffer: 000000007f4de000 - 000000007fffffff
[ 0.607147] reserve RAM buffer: 000000007f543000 - 000000007fffffff
[ 0.607147] reserve RAM buffer: 000000007f5bb000 - 000000007fffffff
[ 0.607147] reserve RAM buffer: 000000007f66a000 - 000000007fffffff
[ 0.607147] NetLabel: Initializing
[ 0.607147] NetLabel: domain hash size = 128
[ 0.607147] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.607147] NetLabel: unlabeled traffic allowed by default
[ 0.607147] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.607147] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.607147] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.620023] Switching to clocksource tsc
[ 0.629983] AppArmor: AppArmor Filesystem Enabled
[ 0.630015] pnp: PnP ACPI init
[ 0.630056] ACPI: bus type pnp registered
[ 0.630970] pnp 00:00: [bus 00-ff]
[ 0.630974] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.630977] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.630980] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.630983] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.630986] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.630989] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.630992] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.630994] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.630997] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.631004] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.631007] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.631010] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.631013] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.631016] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.631018] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.631021] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.631024] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.631027] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[ 0.631120] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.631296] pnp 00:01: [io 0x002e-0x002f]
[ 0.631299] pnp 00:01: [io 0x004e-0x004f]
[ 0.631301] pnp 00:01: [io 0x0068]
[ 0.631303] pnp 00:01: [io 0x006c]
[ 0.631306] pnp 00:01: [io 0x164e-0x164f]
[ 0.631308] pnp 00:01: [io 0x0061]
[ 0.631311] pnp 00:01: [io 0x0070]
[ 0.631313] pnp 00:01: [io 0x0080]
[ 0.631315] pnp 00:01: [io 0x0092]
[ 0.631318] pnp 00:01: [io 0x00b2-0x00b3]
[ 0.631320] pnp 00:01: [io 0x0063]
[ 0.631323] pnp 00:01: [io 0x0065]
[ 0.631325] pnp 00:01: [io 0x0067]
[ 0.631327] pnp 00:01: [io 0x0800-0x080f]
[ 0.631330] pnp 00:01: [io 0x0400-0x047f]
[ 0.631332] pnp 00:01: [io 0x0500-0x053f]
[ 0.631335] pnp 00:01: [mem 0xf8000000-0xfbffffff]
[ 0.631337] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 0.631340] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 0.631342] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 0.631345] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 0.631347] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.631350] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.631464] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.631481] pnp 00:02: [io 0x0000-0x001f]
[ 0.631484] pnp 00:02: [io 0x0081-0x0091]
[ 0.631486] pnp 00:02: [io 0x0093-0x009f]
[ 0.631489] pnp 00:02: [io 0x00c0-0x00df]
[ 0.631492] pnp 00:02: [dma 4]
[ 0.631529] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.631562] pnp 00:03: [io 0x0070-0x0077]
[ 0.631600] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.631707] pnp 00:04: [irq 0 disabled]
[ 0.631722] pnp 00:04: [irq 8]
[ 0.631725] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.631788] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.631803] pnp 00:05: [io 0x00f0]
[ 0.631814] pnp 00:05: [irq 13]
[ 0.631854] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.631868] pnp 00:06: [mem 0xff800000-0xffffffff]
[ 0.631911] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.631932] pnp 00:07: [io 0x0060]
[ 0.631934] pnp 00:07: [io 0x0064]
[ 0.631941] pnp 00:07: [irq 1]
[ 0.631982] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.632016] pnp 00:08: [irq 12]
[ 0.632066] pnp 00:08: Plug and Play ACPI device, IDs SYN1913 SYN1900 SYN0002 PNP0f13 (active)
[ 0.632225] pnp: PnP ACPI: found 9 devices
[ 0.632232] ACPI: ACPI bus type pnp unregistered
[ 0.632249] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.632256] system 00:01: [io 0x0800-0x080f] has been reserved
[ 0.632262] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.632267] system 00:01: [io 0x0500-0x053f] has been reserved
[ 0.632274] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.632281] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.632287] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.632293] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.632299] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.632306] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.632312] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.632327] system 00:04: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.639117] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.639128] pci 0000:00:1c.0: bridge window [io 0x4000-0x5fff]
[ 0.639138] pci 0000:00:1c.0: bridge window [mem 0x95400000-0x963fffff]
[ 0.639147] pci 0000:00:1c.0: bridge window [mem 0x90000000-0x910fffff 64bit pref]
[ 0.639160] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 0.639166] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
[ 0.639176] pci 0000:00:1c.1: bridge window [mem 0x94300000-0x953fffff]
[ 0.639184] pci 0000:00:1c.1: bridge window [mem 0x91100000-0x920fffff 64bit pref]
[ 0.639197] pci 0000:00:1c.4: PCI bridge to [bus 08-09]
[ 0.639203] pci 0000:00:1c.4: bridge window [io 0x2000-0x2fff]
[ 0.639212] pci 0000:00:1c.4: bridge window [mem 0x93300000-0x942fffff]
[ 0.639221] pci 0000:00:1c.4: bridge window [mem 0x92100000-0x930fffff 64bit pref]
[ 0.639233] pci 0000:00:1e.0: PCI bridge to [bus 06-06]
[ 0.639238] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.639247] pci 0000:00:1e.0: bridge window [mem disabled]
[ 0.639254] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.639284] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.639294] pci 0000:00:1c.0: setting latency timer to 64
[ 0.639306] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.639314] pci 0000:00:1c.1: setting latency timer to 64
[ 0.639323] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.639332] pci 0000:00:1c.4: setting latency timer to 64
[ 0.639341] pci 0000:00:1e.0: setting latency timer to 64
[ 0.639346] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.639349] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.639352] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.639355] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
[ 0.639358] pci_bus 0000:02: resource 0 [io 0x4000-0x5fff]
[ 0.639361] pci_bus 0000:02: resource 1 [mem 0x95400000-0x963fffff]
[ 0.639364] pci_bus 0000:02: resource 2 [mem 0x90000000-0x910fffff 64bit pref]
[ 0.639367] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.639370] pci_bus 0000:03: resource 1 [mem 0x94300000-0x953fffff]
[ 0.639373] pci_bus 0000:03: resource 2 [mem 0x91100000-0x920fffff 64bit pref]
[ 0.639376] pci_bus 0000:08: resource 0 [io 0x2000-0x2fff]
[ 0.639379] pci_bus 0000:08: resource 1 [mem 0x93300000-0x942fffff]
[ 0.639382] pci_bus 0000:08: resource 2 [mem 0x92100000-0x930fffff 64bit pref]
[ 0.639385] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7]
[ 0.639388] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff]
[ 0.639391] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.639394] pci_bus 0000:06: resource 7 [mem 0x80000000-0xfebfffff]
[ 0.639443] NET: Registered protocol family 2
[ 0.639600] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.640606] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.643556] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.644283] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.644294] TCP reno registered
[ 0.644322] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.644357] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.644544] NET: Registered protocol family 1
[ 0.644577] pci 0000:00:02.0: Boot video device
[ 0.644863] PCI: CLS 0 bytes, default 64
[ 0.644943] Trying to unpack rootfs image as initramfs...
[ 0.974165] Freeing initrd memory: 12680k freed
[ 0.983107] Simple Boot Flag at 0x44 set to 0x1
[ 0.983397] Scanning for low memory corruption every 60 seconds
[ 0.983582] audit: initializing netlink socket (disabled)
[ 0.983603] type=2000 audit(1300633126.970:1): initialized
[ 0.999184] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.001413] VFS: Disk quotas dquot_6.5.2
[ 1.001492] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.002289] fuse init (API version 7.15)
[ 1.002407] msgmni has been set to 3993
[ 1.002695] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.002705] io scheduler noop registered
[ 1.002709] io scheduler deadline registered
[ 1.002761] io scheduler cfq registered (default)
[ 1.003018] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 1.003036] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.003038] _OSC request data:1 0 1d
[ 1.003135] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 1.003149] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.003151] _OSC request data:1 0 1d
[ 1.003243] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20101013/nspredef-352)
[ 1.003258] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.003260] _OSC request data:1 0 1d
[ 1.003307] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.003337] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.004356] vesafb: framebuffer at 0x80000000, mapped to 0xffffc90004980000, using 3072k, total 3072k
[ 1.004364] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[ 1.004369] vesafb: scrolling: redraw
[ 1.004374] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.040190] Console: switching to colour frame buffer device 128x48
[ 1.076292] fb0: VESA VGA frame buffer device
[ 1.076602] intel_idle: MWAIT substates: 0x1110
[ 1.076605] intel_idle: does not run on family 6 model 15
[ 1.076799] ACPI: AC Adapter [ADP0] (off-line)
[ 1.077307] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 1.077865] ACPI: Power Button [PWRB]
[ 1.078168] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 1.082561] ACPI: Lid Switch [LID]
[ 1.082864] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.083365] ACPI: Power Button [PWRF]
[ 1.083721] ACPI: Fan [FAN] (on)
[ 1.084090] ACPI: acpi_idle registered with cpuidle
[ 1.084277] Monitor-Mwait will be used to enter C-1 state
[ 1.084308] Monitor-Mwait will be used to enter C-2 state
[ 1.084331] Monitor-Mwait will be used to enter C-3 state
[ 1.084338] Marking TSC unstable due to TSC halts in idle
[ 1.084754] Switching to clocksource hpet
[ 1.087179] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.087567] ACPI: Thermal Zone [THRM] (63 C)
[ 1.087921] ERST: Table is not found!
[ 1.088798] Linux agpgart interface v0.103
[ 1.089138] ACPI: Battery Slot [BAT0] (battery present)
[ 1.089187] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[ 1.089364] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[ 1.090709] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 1.097365] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
[ 1.097888] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.251901] brd: module loaded
[ 1.252824] loop: module loaded
[ 1.268416] ata_piix 0000:00:1f.1: version 2.13
[ 1.268444] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.284083] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.284514] scsi0 : ata_piix
[ 1.299943] scsi1 : ata_piix
[ 1.315025] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x60e0 irq 14
[ 1.330349] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x60e8 irq 15
[ 1.346110] Fixed MDIO Bus: probed
[ 1.361104] PPP generic driver version 2.4.2
[ 1.375989] tun: Universal TUN/TAP device driver, 1.6
[ 1.390896] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 1.406199] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.421633] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.437075] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.437080] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.452228] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.467362] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.485936] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[ 1.485961] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x96404c00
[ 1.520022] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.520374] ata1.00: ATAPI: TSSTcorp CDDVDW TS-L632H, TO01, max UDMA/33
[ 1.548726] hub 1-0:1.0: USB hub found
[ 1.560255] ata1.00: configured for UDMA/33
[ 1.576873] hub 1-0:1.0: 4 ports detected
[ 1.590647] scsi 0:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L632H TO01 PQ: 0 ANSI: 5
[ 1.590753] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.590776] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.590781] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.590856] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 1.650056] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.667733] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 1.667757] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x96404800
[ 1.688239] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.700022] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.700193] hub 2-0:1.0: USB hub found
[ 1.700199] hub 2-0:1.0: 6 ports detected
[ 1.700318] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.700338] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.700434] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.700445] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.700449] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.700512] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 1.807722] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.821038] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.821109] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.840070] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000060c0
[ 1.853552] hub 3-0:1.0: USB hub found
[ 1.866855] hub 3-0:1.0: 2 ports detected
[ 1.880123] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.893598] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.893602] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.906957] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.940062] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000060a0
[ 1.953630] hub 4-0:1.0: USB hub found
[ 1.966842] hub 4-0:1.0: 2 ports detected
[ 1.979945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.993389] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.993394] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.006659] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.020001] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00006080
[ 2.033565] hub 5-0:1.0: USB hub found
[ 2.046804] hub 5-0:1.0: 2 ports detected
[ 2.060095] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 2.060179] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.060189] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.060193] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.060257] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.114832] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006060
[ 2.128542] hub 6-0:1.0: USB hub found
[ 2.141883] hub 6-0:1.0: 2 ports detected
[ 2.155132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.168598] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.168603] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.181974] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.195586] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040
[ 2.209236] hub 7-0:1.0: USB hub found
[ 2.222534] hub 7-0:1.0: 2 ports detected
[ 2.235772] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
[ 2.280797] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.294657] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.308221] mice: PS/2 mouse device common for all mice
[ 2.321620] rtc_cmos 00:03: RTC can wake from S4
[ 2.336185] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.349475] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 2.362996] hub 3-0:1.0: over-current change on port 1
[ 2.363006] device-mapper: uevent: version 1.0.3
[ 2.363186] device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@xxxxxxxxxx
[ 2.363255] device-mapper: multipath: version 1.1.1 loaded
[ 2.363258] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.363505] cpuidle: using governor ladder
[ 2.443101] cpuidle: using governor menu
[ 2.456262] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.456483] TCP cubic registered
[ 2.456641] NET: Registered protocol family 10
[ 2.457028] lo: Disabled Privacy Extensions
[ 2.457266] NET: Registered protocol family 17
[ 2.457296] Registering the dns_resolver key type
[ 2.537194] PM: Hibernation image not present or could not be loaded.
[ 2.537212] registered taskstats version 1
[ 2.550278] hub 6-0:1.0: over-current change on port 2
[ 2.550631] Magic number: 3:411:991
[ 2.576433] rtc_cmos 00:03: setting system clock to 2011-03-20 14:58:50 UTC (1300633130)
[ 2.589872] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.603324] EDD information not available.
[ 2.616823] Freeing unused kernel memory: 916k freed
[ 2.630606] Write protecting the kernel read-only data: 10240k
[ 2.644553] Freeing unused kernel memory: 352k freed
[ 2.658514] Freeing unused kernel memory: 1600k freed
[ 2.710779] udev[75]: starting version 167
[ 2.867339] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.867373] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.867431] r8169 0000:02:00.0: setting latency timer to 64
[ 2.867507] r8169 0000:02:00.0: irq 40 for MSI/MSI-X
[ 2.868104] r8169 0000:02:00.0: eth0: RTL8102e at 0xffffc90000332000, 00:1e:33:3b:3a:29, XID 14a00000 IRQ 40
[ 2.899985] ahci 0000:00:1f.2: version 3.0
[ 2.900038] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.900117] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 2.900168] ahci: SSS flag set, parallel bus scan disabled
[ 2.900203] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x3 impl SATA mode
[ 2.900207] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ccc ems
[ 2.900214] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.921414] scsi2 : ahci
[ 2.921583] scsi3 : ahci
[ 2.921721] scsi4 : ahci
[ 2.921878] ata3: SATA max UDMA/133 abar m2048@0x96404000 port 0x96404100 irq 41
[ 2.921883] ata4: SATA max UDMA/133 abar m2048@0x96404000 port 0x96404180 irq 41
[ 2.921885] ata5: DUMMY
[ 3.740091] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.124201] ata3.00: ATA-8: TOSHIBA MK1246GSX, LB213M, max UDMA/100
[ 4.138591] ata3.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.154054] ata3.00: configured for UDMA/100
[ 4.168625] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1246GS LB21 PQ: 0 ANSI: 5
[ 4.183781] sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 4.183825] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 4.213444] sd 2:0:0:0: [sda] Write Protect is off
[ 4.228074] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.228103] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.325823] sda: sda1 sda2 sda3
[ 4.340777] sd 2:0:0:0: [sda] Attached SCSI disk
[ 4.530092] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.965131] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 4.980233] EXT4-fs (sda1): write access will be enabled during recovery
[ 6.311178] EXT4-fs (sda1): orphan cleanup on readonly fs
[ 6.326092] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 287
[ 6.326134] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 23
[ 6.326147] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 21
[ 6.326158] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 20
[ 6.326168] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 19
[ 6.326177] EXT4-fs (sda1): 5 orphan inodes deleted
[ 6.340942] EXT4-fs (sda1): recovery complete
[ 6.434367] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.370833] Adding 1550268k swap on /dev/sda3. Priority:-1 extents:1 across:1550268k
[ 15.384929] udev[286]: starting version 167
[ 15.640512] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 15.872205] lp: driver loaded but no devices found
[ 15.995027] Linux video capture interface: v2.00
[ 16.025242] uvcvideo: Found UVC 1.00 device CNF7051 (04f2:b070)
[ 16.047051] input: CNF7051 as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input4
[ 16.047151] usbcore: registered new interface driver uvcvideo
[ 16.047153] USB Video Class driver (v1.0.0)
[ 16.110669] cfg80211: Calling CRDA to update world regulatory domain
[ 16.162367] [drm] Initialized drm 1.1.0 20060810
[ 16.178618] cfg80211: World regulatory domain updated:
[ 16.178623] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.178627] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.178631] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 16.178634] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 16.178637] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.178640] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.496634] type=1400 audit(1300633144.431:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=538 comm="apparmor_parser"
[ 16.496727] type=1400 audit(1300633144.431:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=538 comm="apparmor_parser"
[ 16.496796] type=1400 audit(1300633144.431:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=538 comm="apparmor_parser"
[ 16.519995] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 16.520036] i915 0000:00:02.0: setting latency timer to 64
[ 16.614011] i915 0000:00:02.0: irq 42 for MSI/MSI-X
[ 16.616806] type=1400 audit(1300633144.551:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=532 comm="apparmor_parser"
[ 16.616899] type=1400 audit(1300633144.551:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=532 comm="apparmor_parser"
[ 16.616967] type=1400 audit(1300633144.551:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=532 comm="apparmor_parser"
[ 16.670610] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 16.670941] [drm] initialized overlay support
[ 16.729625] ath5k 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 16.729643] ath5k 0000:03:00.0: setting latency timer to 64
[ 16.729763] ath5k 0000:03:00.0: registered as 'phy0'
[ 16.897239] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x9280b1, caps: 0xa04711/0xa04000/0x0
[ 16.975163] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[ 17.079636] checking generic (80000000 300000) vs hw (80000000 10000000)
[ 17.079641] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 17.079759] Console: switching to colour dummy device 80x25
[ 17.100083] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is zero.
[ 17.100101] Console: switching to colour frame buffer device 180x56
[ 17.104236] fb0: inteldrmfb frame buffer device
[ 17.104238] drm: registered panic notifier
[ 17.118111] acpi device:19: registered as cooling_device3
[ 17.119924] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 17.120161] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 17.121182] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 17.291158] ath: EEPROM regdomain: 0x69
[ 17.291162] ath: EEPROM indicates we should expect a direct regpair map
[ 17.291166] ath: Country alpha2 being used: 00
[ 17.291169] ath: Regpair used: 0x69
[ 17.392824] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 17.392909] HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 17.392948] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 17.459376] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 17.460108] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa2, PHY: 0x61)
[ 17.618139] hda_codec: ALC268: BIOS auto-probing.
[ 17.623989] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 17.624098] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 17.975795] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 18.055914] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 18.248167] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 18.248239] IP: [<ffffffff81305850>] fb_release+0x30/0x70
[ 18.248286] PGD 7a3e6067 PUD 3714f067 PMD 0
[ 18.248336] Oops: 0000 [#1] SMP
[ 18.248377] last sysfs file: /sys/module/parport/initstate
[ 18.248417] CPU 0
[ 18.248436] Modules linked in: snd_hda_codec_realtek arc4 joydev snd_hda_intel ath5k ath snd_hda_codec snd_hwdep snd_pcm i915 snd_seq_midi snd_rawmidi mac80211 drm_kms_helper snd_seq_midi_event drm cfg80211 snd_seq uvcvideo snd_timer videodev v4l1_compat snd_seq_device psmouse v4l2_compat_ioctl32 i2c_algo_bit snd sparse_keymap video serio_raw lp shpchp soundcore snd_page_alloc output parport ahci r8169 libahci
[ 18.248949]
[ 18.248967] Pid: 237, comm: plymouthd Not tainted 2.6.37-custom13+ #14 Base Board Product Name/EQUIUM L350
[ 18.249030] RIP: 0010:[<ffffffff81305850>] [<ffffffff81305850>] fb_release+0x30/0x70
[ 18.249084] RSP: 0018:ffff880079c57eb8 EFLAGS: 00010286
[ 18.249125] RAX: ffff880079c56000 RBX: ffff88007e816000 RCX: 0000000000000001
[ 18.249166] RDX: 0000000000000000 RSI: ffff880077096300 RDI: ffff88007e816008
[ 18.249208] RBP: ffff880079c57ec8 R08: 0000000000000000 R09: 0000000000000000
[ 18.249248] R10: ffff880077aa06d0 R11: ffff880077096310 R12: ffff88007e816008
[ 18.249290] R13: ffff88007a4eaf00 R14: ffff88007cba23c0 R15: ffff880077aa06d0
[ 18.249333] FS: 00007fb4af842720(0000) GS:ffff88007f200000(0000) knlGS:0000000000000000
[ 18.249390] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 18.249425] CR2: 0000000000000010 CR3: 0000000036c06000 CR4: 00000000000006f0
[ 18.249467] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 18.249508] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 18.249550] Process plymouthd (pid: 237, threadinfo ffff880079c56000, task ffff8800371216c0)
[ 18.249609] Stack:
[ 18.249628] ffff880077096300 0000000000000008 ffff880079c57f18 ffffffff8115af9a
[ 18.249701] ffff880077aa06d0 ffff880077096310 ffff880079c57f78 ffff880077096300
[ 18.249773] ffff880036f9d600 0000000000000000 000000000000000b 0000000000000000
[ 18.249845] Call Trace:
[ 18.249868] [<ffffffff8115af9a>] fput+0xea/0x250
[ 18.249900] [<ffffffff81157680>] filp_close+0x60/0x90
[ 18.249940] [<ffffffff81157d07>] sys_close+0xb7/0x120
[ 18.249985] [<ffffffff8100bf82>] system_call_fastpath+0x16/0x1b
[ 18.250015] Code: 83 ec 10 48 89 1c 24 4c 89 64 24 08 0f 1f 44 00 00 48 8b 9e a0 00 00 00 4c 8d 63 08 4c 89 e7 e8 e7 25 29 00 48 8b 93 c0 03 00 00 <48> 8b 42 10 48 85 c0 74 11 be 01 00 00 00 48 89 df ff d0 48 8b
[ 18.250015] RIP [<ffffffff81305850>] fb_release+0x30/0x70
[ 18.250015] RSP <ffff880079c57eb8>
[ 18.250015] CR2: 0000000000000010
[ 18.250700] ---[ end trace f67893e2336dea83 ]---
[ 18.261642] ppdev: user-space parallel port driver
[ 18.406478] r8169 0000:02:00.0: eth0: link down
[ 18.406853] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.470380] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.584115] type=1400 audit(1300633146.521:8): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=832 comm="apparmor_parser"
[ 19.201311] type=1400 audit(1300633147.141:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=833 comm="apparmor_parser"
[ 19.208214] type=1400 audit(1300633147.141:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=833 comm="apparmor_parser"
[ 19.220165] type=1400 audit(1300633147.161:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=833 comm="apparmor_parser"
[ 26.843338] audit_printk_skb: 18 callbacks suppressed
[ 26.847452] type=1400 audit(1300633154.781:18): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=849 comm="apparmor_parser"
[ 26.857010] type=1400 audit(1300633154.791:19): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=849 comm="apparmor_parser"
[ 26.866407] type=1400 audit(1300633154.811:20): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=849 comm="apparmor_parser"
[ 115.580038] usb 6-1: new full speed USB device using uhci_hcd and address 2
[ 115.710061] usb 6-1: device descriptor read/64, error -71
[ 115.950059] usb 6-1: device descriptor read/64, error -71
[ 116.180059] usb 6-1: new full speed USB device using uhci_hcd and address 3
[ 116.310058] usb 6-1: device descriptor read/64, error -71
[ 116.550039] usb 6-1: device descriptor read/64, error -71
[ 116.780039] usb 6-1: new full speed USB device using uhci_hcd and address 4
[ 117.200037] usb 6-1: device not accepting address 4, error -71
[ 117.320039] usb 6-1: new full speed USB device using uhci_hcd and address 5
[ 117.740057] usb 6-1: device not accepting address 5, error -71
[ 117.740114] hub 6-0:1.0: unable to enumerate USB device on port 1
[ 155.730081] usb 2-3: new high speed USB device using ehci_hcd and address 3
[ 155.985889] usb 2-3: selecting invalid altsetting 1
[ 155.985958] usbcore: registered new interface driver uas
[ 156.016724] Initializing USB Mass Storage driver...
[ 156.016961] scsi5 : usb-storage 2-3:1.0
[ 156.017134] usbcore: registered new interface driver usb-storage
[ 156.017180] USB Mass Storage support registered.
[ 157.013514] scsi 5:0:0:0: Direct-Access USB-HS SAMSUNG SP0411N 0.01 PQ: 0 ANSI: 0
[ 157.014966] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 157.017760] sd 5:0:0:0: [sdb] 78242976 512-byte logical blocks: (40.0 GB/37.3 GiB)
[ 157.019509] sd 5:0:0:0: [sdb] Write Protect is off
[ 157.019559] sd 5:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 157.019590] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 157.023359] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 157.032759] sdb: sdb1
[ 157.037001] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 157.037054] sd 5:0:0:0: [sdb] Attached SCSI disk
Script started on Sun 20 Mar 2011 14:59:56 GMT
root@calder:~# # plugging in device but not enabled
root@calder:~# dmesg | tail
[ 115.710061] usb 6-1: device descriptor read/64, error -71
[ 115.950059] usb 6-1: device descriptor read/64, error -71
[ 116.180059] usb 6-1: new full speed USB device using uhci_hcd and address 3
[ 116.310058] usb 6-1: device descriptor read/64, error -71
[ 116.550039] usb 6-1: device descriptor read/64, error -71
[ 116.780039] usb 6-1: new full speed USB device using uhci_hcd and address 4
[ 117.200037] usb 6-1: device not accepting address 4, error -71
[ 117.320039] usb 6-1: new full speed USB device using uhci_hcd and address 5
[ 117.740057] usb 6-1: device not accepting address 5, error -71
[ 117.740114] hub 6-0:1.0: unable to enumerate USB device on port 1
root@calder:~# # enabling device (and waiting a few seconds)
root@calder:~# dmesg | tail
[ 157.013514] scsi 5:0:0:0: Direct-Access USB-HS SAMSUNG SP0411N 0.01 PQ: 0 ANSI: 0
[ 157.014966] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 157.017760] sd 5:0:0:0: [sdb] 78242976 512-byte logical blocks: (40.0 GB/37.3 GiB)
[ 157.019509] sd 5:0:0:0: [sdb] Write Protect is off
[ 157.019559] sd 5:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 157.019590] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 157.023359] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 157.032759] sdb: sdb1
[ 157.037001] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 157.037054] sd 5:0:0:0: [sdb] Attached SCSI disk
root@calder:~# fdisk -l
Disk /dev/sda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x47c7fe89
Device Boot Start End Blocks Id System
/dev/sda1 * 1 1245 10000431 83 Linux
/dev/sda2 1246 14400 105667537+ 83 Linux
/dev/sda3 14401 14593 1550272+ 82 Linux swap / Solaris
Disk /dev/sdb: 40.1 GB, 40060403712 bytes
255 heads, 63 sectors/track, 4870 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xce3e5a45
Device Boot Start End Blocks Id System
/dev/sdb1 1 522 4192933+ 6 FAT16
root@calder:~# mount /dev/sdb1 /media/tascam
root@calder:~# ls /media/tascam
BACKUP UTILITY WAVE
root@calder:~# umount /dev/sdb1
root@calder:~# lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 0644:800d TEAC Corp. TASCAM Portastudio DP-01FX
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04f2:b070 Chicony Electronics Co., Ltd
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@calder:~# # about to run complete dmesg ...
root@calder:~# exit
Script done on Sun 20 Mar 2011 15:02:43 GMT
