From: Anand Gadiyar <gadiyar@xxxxxx>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@xxxxxx>
Cc: Keshava Munegowda <keshava_mgowda@xxxxxx>
Cc: Tony Lindgren <tony@xxxxxxxxxxx>
Signed-off-by: Felipe Balbi <balbi@xxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxx>
---
arch/arm/mach-omap2/board-4430sdp.c | 19 -------------------
1 files changed, 0 insertions(+), 19 deletions(-)
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 1230121..f603f3b 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -44,7 +44,6 @@
#define ETH_KS8851_IRQ 34
#define ETH_KS8851_POWER_ON 48
#define ETH_KS8851_QUART 138
-#define OMAP4SDP_MDM_PWR_EN_GPIO 157
#define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO 184
#define OMAP4_SFH7741_ENABLE_GPIO 188
@@ -251,16 +250,6 @@ static void __init omap_4430sdp_init_irq(void)
gic_init_irq();
}
-static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
- .phy_reset = false,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL,
-};
-
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_UTMI,
.mode = MUSB_OTG,
@@ -577,14 +566,6 @@ static void __init omap_4430sdp_init(void)
omap_serial_init();
omap4_twl6030_hsmmc_init(mmc);
- /* Power on the ULPI PHY */
- status = gpio_request(OMAP4SDP_MDM_PWR_EN_GPIO, "USBB1 PHY VMDM_3V3");
- if (status)
- pr_err("%s: Could not get USBB1 PHY GPIO\n", __func__);
- else
- gpio_direction_output(OMAP4SDP_MDM_PWR_EN_GPIO, 1);
-
- usbhs_init(&usbhs_bdata);
usb_musb_init(&musb_board_data);
status = omap_ethernet_init();
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
